Operating Instructions
VACUUM CLEANER
❈ Before operating this unit, please read the instructions carefully.
Register your product at www.samsung.com/global/register
FEATURES
Features include automatic cord rewind and dust indicator.
NOTE : Not all models have the same features.
IMPORTANT SAFEGUARDS
1. Read all instructions carefully. Before switching on, make sure that the
voltage of your electricity supply is the same as that indicated on the
rating plate on the bottom of the cleaner.
2. WARNING: Do not use the vacuum cleaner when rug or floor is wet.
3. Close supervision is necessary when any appliance is used by or near
children. Do not allow the vacuum cleaner to be used as a toy. Do not
allow the vacuum cleaner to run unattended at any time. Use the vacuum
cleaner only for its intended use as described in these instructions.
4. Do not use the vacuum cleaner without a dust bag. Change the dust bag
before it is full in order to maintain best efficiency.
5. Do not use the vacuum cleaner to pick up matches, live ashes or
cigarette butts. Keep the vacuum cleaner away from stoves and other
heat sources. Heat can deform and discolour the plastic parts of the unit.
6. Avoid picking up hard, sharp objects with the vacuum cleaner as they
may damage the cleaner parts. Do not stand on the hose assembly. Do
not put a weight on the hose. Do not block the suction or the exhaustion
part.
7. Switch the vacuum cleaner off at the machine before unplugging from the
electrical outlet. Grasp the plug to disconnect from power outlet to avoid
damage to cord, plug, prongs or socket. Do not pull the power cord.
Always disconnect cord from electrical outlet before changing the dust
bag.
8. The use of an extension cord is not recommended.
9. If your vacuum cleaner is not operating correctly, switch off the power
supply and consult an authorized service agent.
10. Do not attempt to replace a damaged power supply cord. Only the
manufacturer or qualified service personnel can replace power cords.
Serious injury may result.
1
IDENTIFICATIONS OF PARTS
HANDLE
AIR REGULATOR
TUBE*
FLOOR NOZZLE*
RUG/FLOOR SELECTOR
BUTTON FOR
SUCTION HOSE
REMOVAL
BELT-STRAP ASSY
SUCTION HOSE
CORD REWIND
BUTTON
DUST-FULL
INDICATOR
POWER CONTROL
SWITCH* & ON/OFF
SWITCH
CARRYING HANDLE
CLAMPER FOR DUST
BAG COMPARTMENT
*
CREVICE-TOOL
HANGER ACCESSORY DUSTING BRUSH
▲
Features marked * may vary according to model.
2
ASSEMBLING THE VACUUM-CLEANER READY FOR USE
1) Connect the suction hose to the
suction tube.
2) Connect the suction tubes together
(depending on model).
3) Connect the nozzle to the suction
tube.
4) Grip the body connector with one
hand and squeeze the tube in an
inward direction.
OPTION :
① EXTENDING : Holding the
narrow part of the telescopic
tube with one hand, pull the
handle in the opposite direction
with your other hand.
➁ SHORTENING : Holding the
narrow part of the telescopic
tube with one hand, push the
handle towards it using the other
hand.
- Adjustable telescopic tube not
available with all models.
POWER CORD
1) PULLING OUT
The power cord is long enough to be
drawn out for convenience.
2) REWINDING
When you have finished cleaning,
disconnect the plug from the electrical
outlet and simply press the cord
rewind button lightly with your toe.
NOTE : When removing the power cord from the electrical outlet, grasp the
plug, not the cord.
3
With the cord plugged into an electrical outlet,
start or stop the vacuum cleaner by pushing
lightly downward on the switch.
NOTE :
ON/OFF switch is combined with
POWER CONTROLLER - To start or stop
the unit just lightly press it downward.
POWER CONTROL
The vacuuming power can be adjusted to suit
any situation with the electrical power control.
MIN = For delicate fabrics, e.g.net curtains.
MAX =
For hard floors and heavily soiled carpets.
-To adjust power output just turn it right or left.
(VARIABLE CONTROL TYPE ONLY)
DUST-FULL INDICATOR
ON/OFF SWITCH
If the “Dust-Full” indicator changes to “RED” while you are cleaning, the dust
bag requires replacement.
NOTE : If the “Dust-Full” indicator continues to display “RED” even after
changing the dust bag, turn the cleaner off and check whether the
hose, tube or nozzle is clogged.
USING THE ACCESSORIES
CREVICE DUSTING
Crevice tool for radiators,
crevices, corners, between
cushions.
Your cleaner features a tool storage device.
Assemble the accessory hanger on to the
extension tube.
It can be used to store the cleaning tools while
they are not in use.
This tool can be separated into two parts.
Dusting brush for
furniture, shelves, books,
etc.
4
•
Before use, assemble the
dusting brush to the crevice
tool
TOOL STORAGE
USING & ASSEMBLING THE STRAP
This appliance is designed to be
conveniently carried on your waist using the
belt-strap accessory.
When cleaning steps, curtains, shelves, etc,
you can carry the unit with the strap over
your shoulder.
Ready for use
▼
1) Insert the lockers into the holes on the
cleaner, taking care of the lockers’ direction.
*
Strap-ends should face the body of the
cleaner.
2) Pull the lockers to the front of the cleaner
until they click into place.
3) Adjust the strap length to fit your body.
When not using the strap
▼
- Detach the lockers by pushing them down
and drawing them out from the unit.
-
Keep the strap separately for the next time
you want to use it
.
1)
2) 3)
PARK POSITION
Located on the top rear side of the vacuumcleaner, there is a nozzle support that can be
used to park the nozzle during pauses in
cleaning.
(OPTIONAL)
*
Locker
TRANSPORTING AND STORING THE VACUUM CLEANER
For easy storage and transportation, this vacuum
cleaner has a clip system built onto the body,
which will keep the tube, hose and nozzle in a
vertical position.
5
1) To open the dust cover of the dust
bag compartment, press the clamper
upwards.(The clamper is located at
the front of the dust cover)
3)
After removing the used dust bag,
insert the cardboard bag collar of the
new dust bag into its original position.
2) Remove the dust bag from the
cleaner.
4) Press the dust cover down gently
until the clamper relocks.
FOR CLOTH FILTER BAG
REPLACING THE DUST BAG
After using, if the cloth filter bag is full of dust, clean the cloth filter bag and use it again.
MAINTENANCE OR REPLACEMENT OF THE FILTERS
INLET FILTER
▼
To protect the motor, your cleaner features a secondary filter at the front of the motor in
the dust compartment. Do not allow the filter to become clogged. Suction power reduction or motor damage may result. After cleaning the secondary filter attach it in place.
SECONDARY FILTER
SECONDARY FILTER
OUTLET FILTER
▼
1) Open the grille part, separate the
exhausted filter.
2) Reassemble it after cleaning or
replacing the filter in the reverse order.
NOTE: The filters must be completely dried before being replaced in the dust
compartment.
6
USAGE OF FLOOR NOZZLE
FOR RUG / FLOOR SELECTOR
Before use make sure that the position of the selector is in the right position for
the type of surface to be cleaned.
Select the carpet indicator ➀ when cleaning carpets.
Select flat surface indicator ➁ when cleaning the
floors, tiles, etc.
FOR UNIVERSAL BRUSH
Use the floor nozzle for cleaning all surfaces.
NOTE: For optimum efficiency, clean floor brush with crevice tool.
TROUBLE SHOOTING
PROBLEM CAUSE REMEDY
Motor does not start. No power supply. Check cable, plug and
Suction force is gradually Filter, nozzle, suction hose Remove the object.
decreasing. or tube is blocked.
Cord does not rewind fully. Check that the cord is not Pull the cord out 2~3m &
If you have any comments or questions regarding a Samsung products,
contact the SAMSUNG customer care center.
Country
AUSTRALIA
HONG KONG
MALAYSIA
SINGAPORE
twisted or wound unevenly. push down the cord rewind
Customer Care Center
1300 362 603
2862 6001
1800-88-9999
1800-SAMSUNG (7267864)
7
socket.
button.
☎
Web Site
www.samsung.com/au
www.samsung.com/hk
www.samsung.com/my
www.samsung.com/sg
DJ68-00094J REV(1.0)
Loading...