This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must by authorized by Macrovision Corporized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Symbols
1
Press/push
= Step number
1
4
1
Hold down
☛
ImportantNote
➢
Safety Instructions
The following illustrations represent precautions.
The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.
DO NOT OPEN THE DVD-VCR. Refer to service personnel.
GB
10%75%
HH
40°C
5°C
Do NOT expose the DVD-VCR
to extreme temperature conditions (below 5°C and above
40°C) or to extreme humidity
conditions (less than 10% and
more than 75%).
Do NOT place any objects on
the DVD-VCR or remote
control.
Do NOT expose the DVD-VCR
to direct sunlight.
During a storm and/or lightning, unplug the DVD-VCR
from the mains socket and
aerial.
Do NOT expose the DVD-VCR
to any liquids.
If the remote control is not
used for a long period of time,
remove the batteries and store
it in a cool, dry place.
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL
ENVIRONMENTS
5
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos :
GB
Disc Types
(Logos)
DVD
VIDEO-CD
AUDIO-CD
Recording
Types
Audio
+
Video
Audio
+
Video
Audio
Disc Size
12 Cm
8 Cm
12 Cm
8 Cm
12 Cm
8 Cm
Max.
Playing
Time
Single-sided
240 min.
Double-sided
480 min.
Single-sided
80 min.
Double-sided
160 min.
74 min.
20 min.
74 min.
20 min.
Characteristics
• DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
• Various screen and audio
functions can be easily selected
through the on-screen menu.
• Video with CD sound, VHS
quality & MPEG-1 compression
technology.
• An LP is recorded as an analog
signal with more distortion. CD
is recorded as a Digital Signal
with better audio quality, less
distortion and less deterioration
of audio quality over time.
* DO NOT play CD-ROM, CD-I and DVD-ROM in this player!
(CDGs play audio only, not graphics.)
Disc Markings
~
• Playback
Region
Number
PAL
PAL colour system
•
in Australia,
Newzealand, etc.
NTSC
• NTSC broadcast
system in USA,
Canada, japan,
• Dolby
Digital disc
STEREO
• Stereo
disc
South Korea, etc.
Playback Region Number
Both the DVD player and the discs are coded by region. These regional codes must match in order for the
disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
6
DIGITAL
SOUND
• Digital
Audio disc
• DTS disc
Front View of the DVD-VCR
( DVD-V70 )
RECORD
BUTTON
OPEN/CLOSE
BUTTON
STANDBY/ON
BUTTON
REW /SKIP BACK
BUTTON
DVD DECK
VIDEO CASSETTE
COMPARTMENT
DVD SELECT BUTTON
VCR SELECT BUTTON
EJECT BUTTON
GB
STANDBY/ON
STOP BUTTON
PLAY/STILL
BUTTON
( DVD-V80 )
STANDBY/ON
BUTTON
STOP BUTTON
REW /SKIP BACK
STANDBY/ON
PLAY/STILL
BUTTON
BUTTON
F.F / SKIP NEXT
BUTTON
DVD DECK
RECORD
BUTTON
F.F / SKIP NEXT
BUTTON
EZ VIEW BUTTON
OPEN/CLOSE
BUTTON
EZ VIEW BUTTON
PROG
DVD
PROGRAMME
SELECTION BUTTON
VIDEO CASSETTE
COMPARTMENT
DVD SELECT BUTTON
PROG
DVD
PROGRAMME
SELECTION BUTTON
VCR
LINE2 VIDEO
INPUT JACK
VCR SELECT BUTTON
VCR
LINE2 VIDEO
INPUT JACK
LINE2
LINE2
LINE2 AUDIO L, R
INPUT JACK
EJECT BUTTON
EJECT
LINE2 AUDIO L, R
INPUT JACK
( DVD-V85 )
STANDBY/ON
BUTTON
STOP BUTTON
REW /SKIP BACK
STANDBY/ON
PLAY/STILL
BUTTON
BUTTON
DVD DECK
RECORD
BUTTON
F.F / SKIP NEXT
BUTTON
OPEN/CLOSE
BUTTON
EZ VIEW BUTTON
VIDEO CASSETTE
COMPARTMENT
DVD SELECT BUTTON
PROG
PROGRAMME
SELECTION BUTTON
DVD
VCR SELECT BUTTON
VCR
LINE2
LINE2 VIDEO
INPUT JACK
EJECT BUTTON
LINE2 AUDIO L, R
INPUT JACK
7
Rear View of the DVD-VCR
( DVD-V70 )
GB
DIGITAL AUDIO OUT
SOCKET (COAXIAL)
S-VIDEO OUT
JACK
COMPONENT
VIDEO OUT
AUDIO LINE OUT TO TV
(S-VIDEO OR COMPONENT)
( DVD-V80 / DVD-V85)
LINE IN 1
LINE OUT TO TV
(COMPOSITE)
RF ANTENNA INPUT
RF OUT TO TV
DIGITAL AUDIO OUT
SOCKET (COAXIAL)
S-VIDEO OUT JACK
DIGITAL AUDIO OUT
SOCKET (OPTICAL)
COMPONENT
VIDEO OUT
AUDIO LINE OUT TO TV
(S-VIDEO OR COMPONENT)
LINE IN 1
LINE OUT TO TV
(COMPOSITE)
RF ANTENNA INPUT
RF OUT TO TV
8
Infrared Remote Control
( DVD-V70 )
10
11
12
13
14
15
16
17
STANDBY/ON
1
OPEN/CLOSE
18
1STANDBY/ON
2SHUTTLE << / >>
3CLEAR
GB
4DVD, VCR SELECT
5AUDIO
6TRK
7REWIND
2
19
3
20
21
4
5
6
7
8
9
22
23
24
25
26
27
OK
28
29
30
31
8STOP
9SUBTITLE
10 MENU
11 UP
12 LEFT
13 DOWN
14 SPEED SP/LP
15 RECORD
16 TIMER
17 ANGLE
25 PLAY/STILL
26 INFO.
27 RETURN
28 RIGHT
29 OK
30 EZ VIEW
31 DISC MENU
32 MARK
SEARCH
33 MODE
REPEAT
10
Display Indicators
O
P
E
N
/
C
L
O
S
E
S
T
A
N
D
B
Y
/
O
N
1 2 3 4 5
6 7 8
GB
STEREO
1The DVD Deck is active
2A DVD, CD, VCD, or SVCD is loaded
3The time, counter position, time remaining or
current deck status is displayed
4VHS tape is inserted
6A DVD with a DTS soundtrack is loaded
7The Hi-Fi track of a VHS tape is playing
(The current TV show or video is broadcast in
Stereo)
8 A Timer Recording is programmed or in progress.
5The VCR Deck is active
Accessories
You have just purchased a SAMSUNG Video Cassette Recorder (DVD-VCR).
Together with your DVD-VCR, you will find the following accessories in the box.
REMOTE CONTROL
& BATTERIES
AUDIO & VIDEO
CABLE
OWNER’S
INSTRUCTIONS
COAXIAL CABLE
11
GB
Deciding How to Connect DVD-VCR
You must take into account various factors when connecting audio or video systems:
◆ Types of connectors available on your systems
◆ Systems connected permanently to the DVD-VCR (satellite receiver for example) or
temporarily (camcorder for example)
Your DVD-VCR is equipped with the following connectors.
ConnectorLocationTypeDirectionRecommended Use
LINE 1
Audio outputRearAudio RCAOut◆ Audio out (DVD only)
LINE 2
COMPONENT RearRCAOut◆ COMPONENT out (DVD only)
output
S-VIDEO RearS-JACKOut◆ S-Video out (DVD only)
output
Digital AUDIO RearOptical
outputcoaxial
RearAudio/Video RCAIn/Out◆ Television
Front
LINE 2
Audio/VideoVideo in
★
(DVD-V80/ DVD-V85)
In◆ Audio in
Out◆ Digital Audio out (DVD only)
◆ Other VCR
OUT TO TVRear75 ΩOut◆ Television
coaxial
IN FROM ANT. Rear75 ΩIn◆ Aerial
coaxial◆ Cable television network
◆ Satellite receiver
☛ Whenever you connect an audio or video system to your DVD-VCR, ensure that all elements
are switched off
Refer to the documentation supplied with your equipment for detailed connection instructions
12
.
Connecting DVD-VCR to the TV using the Coaxial Cable
To receive television programmes a signal must be received from
one of the following sources:
◆ An outdoor aerial
◆ An indoor aerial
◆ A cable television network
◆ A satellite receiver
☛ Make sure that both the television and the DVD-VCR are
switched off
1Remove the aerial or network input cable from the television.
2Connect this cable to the 75Ω coaxial socket marked on the
rear of your DVD-VCR.
3Plug the coaxial cable supplied into the socket on your
DVD-VCR.
4Plug the other end of the coaxial cable into the connector
previously used for the aerial on the television.
5To obtain better quality pictures and sound on your television, you
can also connect your DVD-VCR to the television via the RCA
cable (see section below) if your television is equipped with this
type of connection.
before connecting the cables.
TV
TV
4
GB
2
3
Connecting DVD-VCR to the TV using the RCA Cable
Aerial
TV
3
RF coaxial cable
You can connect your DVD-VCR to the television using the RCA cable if the appropriate input is available on
the television. You thus:
◆ Obtain better quality sound and pictures
◆ Simplify the setting up procedure of your DVD-VCR
2
☛ ◆ Regardless of the type of connection chosen, you must always connect the coaxial cable supplied.
Otherwise, no picture will be visible on the screen when the DVD-VCR is switched off.
◆ Make sure that both the television and the DVD-VCR are switched off
1Connect the coaxial cable as indicated in the above section.
before connecting the cables.
2Connect one end of the RCA Audio/Video cable to the Video output and Audio L, R output socket on the rear of
the DVD-VCR.
3Plug the other end into the appropriate connector on the television.
13
GB
Connecting DVD-VCR to a Satellite Receiver or Other Equipment
You can connect other audio and/or video equipment to your DVD-VCR in different ways. The following
illustrations give a few examples of the connection possibilities.
➢The RCA input/output connectors on the rear of the DVD-VCR are used for equipment, such as
camcorders, VCRs or sound systems.
Camcorder
VCR
REAR OF THE DVD-VCR
Sound system
14
Plug & Auto Set up
Your DVD-VCR will automatically set itself up when it is plugged
into the mains for the first time. TV stations will be stored in
memory. The process takes a few minutes. Your DVD-VCR will
then be ready for use.
1Connect the coaxial cable as indicated on page 13.
(Connecting Your DVD-VCR to the TV Using the Coaxial Cable)
2Plug the DVD-VCR into the mains.
Result:The Language Set menu is displayed.
TV
GB
3Select the required language by pressing the
or
4Press OK to store the language selected.
Result
:A message appears.
5Press OK button.
6Press OK to start the auto scanning.
◆The number of stations automatically stored by the VCR
depends on the number of stations that it has found.
➢ Auto preset can be performed by pressing
the VCR continuously for 5 seconds or more with no
tape inserted.
(STOP) on
■
buttons.
Please wait
2
Auto setup
00 %
Clock Set
Time Date Year
12 : 00 1/JAN 2003
WED
15
Tuning Your Television for the DVD-VCR
You must tune your television for the DVD-VCR only if you are not
using a RCA cable
GB
STANDBY/ON
OPEN/CLOSE
2
➢ To view pictures from your DVD-VCR when a RCA cable
is used, the television must be set to the audio/video
mode (AV).
1Switch on the television.
2Switch on the DVD-VCR by pressing STANDBY/ON on the front of
the DVD-VCR or STANDBY/ON on the remote control.
3Select a programme position on the television to be reserved for
use with your DVD-VCR.
4Insert the video cassette in the DVD-VCR. Check that the
DVD-VCR starts reading the cassette; if not, press
II
button
.
5Start a scan on your television or set the television to UHF
channel 36 (Australia:UHF 38 CH).
4
6Fine tune the television until the pictures and sound are obtained
clearly.
7If you cannot find the pictures and sound, or there is interference
from nearby channels, it may be necessary to change the setting
of the DVD-VCR output channel (see Setting the DVD-VCR
Output Channel on page 25 and Problems and Solutions on page
69).
8When the picture and sound are perfectly clear, store this channel
at the desired programme position on the television.
:That programme is now reserved for use with your
Result
DVD-VCR.
16
Deck Control Keys
The DVD-VCR uses one set of controls to operate both decks. The
following keys are helpful in successfully controlling each deck.
1STANDBY/ON Button
Press the STANDBY/ON button on the remote control or front
panel to turn on the DVD-VCR.
2DVD Button
Press the DVD button on the remote control when you want to
control the DVD deck.
◆ The DVD indicator will light on the Front Panel Display to show
that the DVD deck is selected.
VCR Button
3
Press the VCR button on remote control when you want to control
the VCR deck.
◆ The VCR indicator will light on the Front Panel Display to show
that VHS deck is selected.
4INPUT SEL. BUTTON
Press the INPUT SEL. button repeatedly to cycle through all of
your input sources, including the Tuner (PR##), Line 1 (rear AV
input), and Line 2 (front AV input).
• Input select is only available when the VCR deck is selected.
➢ Before using the VCR operation of 21~47 pages, press
the VCR button on the remote control to select VCR
mode.
Before using the DVD operation of 48~67 pages, press
the DVD button on the remote control to select and
watch DVD.
STANDBY/ON
STANDBY/ON
1
2
1
3
4
GB
17
Basic TV Tuner Operations
The following buttons are used when watching television via the
DVD-VCR’s built-in TV tuner.
GB
1
1TV/VCR Button
Press to switch between your TV’s tuner and the VCR’s internal
tuner.
2PROG Button
Press to change to the next or previous channel.
30-9 Buttons
Press to select channels directly.
2
2
3
4INFO.
Press to display the channel you are watching.
◆ Also works in DVD and VCR mode.
18
4
OK
Inserting Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the DVD-VCR
◆ Find that the remote control is no longer working
correctly
1Push the tab in the direction of the arrow to release the battery
compartment cover on the rear of the remote control.
2Insert two AAA, RO3 or equivalent batteries, taking care to respect
the polarities:
◆+ on the battery with + on the remote control
◆– on the battery with – on the remote control
3Replace the cover by aligning it with the base of the remote
control and pushing it back into place.
➢ Do not mix different battery types (manganese and
alkaline for example).
Setting the Date and Time
1
GB
Your DVD-VCR contains a 24-hour clock and calendar used to:
◆ Automatically stop programme recording
◆ Preset your DVD-VCR to record a programme
automatically
You must set the date and time when:
◆ You purchase the DVD-VCR
☛
1After pressing the MENU, press the OK or
2Press the corresponding
3Press the OK or
4Press
5Press the
◆ Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
:The Setup menu is displayed.
Result
,
option.
Result
:The Clock Set menu is displayed.
¥or
Result
:The option selected highlight.
Result
or
:The day of the week is displayed automatically.
➢You can hold the
quickly through the values.
to select this option.
to select the hour, minutes, day, month and year.
buttons to increase or decrease the value.
or
buttons down to scroll more
.
buttons to select the Clock
6On completion, press RETURN to exit the menu.
Clock Set
Time Date Year
12 : 00 1 / JAN / 2003 WED
19
GB
Setting the Menu Language
1Open “MENU”
After pressing the MENU, press the OK or
1
OK
2Select “Language”
Use the orbuttons to highlight
“Language,” then press the OK or
3Set menu Language
Place the selection arrow next to your desired Language, then
press the OK button.
.
.
English
Français
Deutsch
Español
Italiano
Nederlands
Language Set
4Press the
or
buttons to select language you want.
Place the selection arrow next to your desired Language, then
press the OK button.
5On completion, press RETURN to exit the menu.
20
Presetting the Stations Automatically
You do not need to preset the stations if you have already
☛
set them automatically (see Plug & Auto Set Up on page 15).
Your DVD-VCR contains a built-in tuner used to receive television
broadcasts.
You must preset the stations received through the tuner. This can be
done:
◆ Plug & Auto Set up (see page 15)
◆ Automatically
◆ Manually (see page 22)
You can store up to 80 stations.
VCR
GB
Australia Model
1After pressing the MENU, press the OK or
.
Result:The Setup menu is displayed.
2Press the corresponding
,
buttons to select the Install
option.
3Press the OK or
Result
:The Install menu is displayed.
4Press the corresponding
to select this option.
or
buttons, until the Auto Setup
is selected.
And then press the OK or
:A message appears, indicating that any channels
Result
to select this option.
already preset on your DVD-VCR will be deleted.
5Press OK button.
:A message appears, indicating that any channels
Result
already preset on your VCR will be deleted.
6Press OK to start the auto scanning.
Result
:◆ The Please Wait indication highlight on the
television screen.
◆ The first frequency band is scanned and the first
station found is displayed and stored.
◆ The DVD-VCR then searches for the second station
and so on.
◆ When the automatic scanning procedure has
finished, the DVD-VCR switches automatically to
programme 1.
➢The number of stations automatically stored by the DVD-
VCR depends on the number of stations that it has found.
Auto Setup
Manual Setup
VCR Output CH : CH 38
Newzealand Model
Auto Setup
Manual Setup
TV System : G
VCR Output CH : CH 36
Your date will be lost
Press OK to continue
Menu to exit
Install
Install
Auto Setup
7If you wish to cancel the auto scanning before the end, press the
MENU button to exit the menu.
➢◆ Once the auto scanning procedure has finished, some
stations may have been stored more than once; select
the stations with the best reception and delete the ones
no longer required (see page 23).
Auto Setup
Please Wait
15%
21
VCR
Presetting the Stations Manually
☛ You do not need to preset the stations manually if you
have already set them automatically.
GB
Australia Model
Auto Setup
Manual Setup
VCR Output CH : CH 38
Newzealand Model
Auto Setup
Manual Setup
TV System : G
VCR Output CH : CH 36
TV STATION TABLE
PR CH NAME
1
2
3
4
5
SWAPPING : OK
DELETE : CLEARRETURN
MANUAL TUNING
PR :
CH : - -
MFT : NAME : - - - -
MEMORY : OK
RETURN
Install
Install
1After pressing the MENU, press the OK or
.
Result:The Setup menu is displayed.
2Press the corresponding
,
buttons to select the Install
option.
3Press the OK or
Result:The
4Press the corresponding
to select this option.
Install menu is displayed.
or
buttons, until the Manual
Setup option is selected.
5Press the OK or
Result
:The TV STATION TABLE menu is displayed.
6Press the
required.
7Press the
Result
:The MANUAL TUNING menu is displayed.
8Press the
Result:The frequency band is scanned and the first station
9Press the
The station name is set automatically from the broadcast signal.
10To change the programme’s name, press the
:The first letter of the name flashes.
Result
to select a Manual Setup option.
or buttons to select a programme number as
button to preset the station.
¥or
buttons to start scanning channel.
found is displayed.
or
buttons until the NAME is selected.
button.
11To...Then...
Select a character Press the orbutton until the
in the namerequired character is displayed
(letters, numbers or “-” character).
Move to the next orPress the or ¥buttons
previous characterrespectively.
12If you...Then...
Wish to store the◆ Press the or
station displayedis selected.
◆ Press the
picture, if necessary.
◆ Press OK to store the station
Do not wish to ◆ Press the or
store the stationis selected.
displayed
◆ Press the
scanning the frequency band and display
the next station
◆ Go back to the beginning of Step 14
buttons until the MFT
¥or
buttons to adjust the
buttons until the CH
¥or
buttons to go on
13Repeat this procedure from Step 6 onwards, until all the required
stations have been stored.
14On completion, press the RETURN button three times to exit the
menu.
22
Loading...
+ 49 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.