1. Warning: Prior to repair, disconnect the
power cord from the circuit breaker.
2. Use proper parts: Use only exact replacement parts. (Also, we recommend replacing
parts rather than repairing them.)
3. Use the proper tools: Use the proper tools
and test equipment, and know how to use
them. Using defective tools or test equipment may cause problems later-intermittent
contact, for example.
4. Power Cord: Prior to repair, check the
power cord and replace it if necessary.
5. Avoid using an extension cord, and avoid
tapping into a power cord. This practice
may result in malfunction or fire.
6. After completing repairs and reassembly,
check the insulation resistance.
Procedure: Prior to applying power, measure the resistance between the power cord
and the ground terminal. The resistance
must be greater than 30 megaohms.
Fig. 1-1 Avoid Dangerous Contact
Fig. 1-2 No Tapping and No Extension Cords
7. Make sure that the grounds are adequate.
8. Make sure that the installation conditions
are satisfactory.
Relocate the unit if necessary.
9. Keep children away from the unit while it is
being repaired.
10. Be sure to clean the unit and its surrounding area.
Fig. 1-3 No Kids Nearby!
Fig. 1-4 Clean the Unit
1-1Samsung Electronics
MEMO
Samsung Electronics1-2
2. Product Specifications
2-1 Table
Item
Power Sourse
Performance
Electrical
Rating
Features
Dimensions
&
Weight
Model
Capacity (ISO/SASO)kcal/h
BTU/h
2
Air circulation (High)m
Moisture removal (High)Liters/h
Available voltage rangeV
Running amperesA
Power inputkw
Power factor%
Energy efficiency ratioBTU/wh
Compressor locked rotor amperesA
Controls/Temperature control
Control unit
Timer
Fan speedIndoor/Outdoor
Airflow direction (indoor)Horizontal
Comperssor
Refrigerant/Amount charged at ratingg
Refrigerant control
Operation soundIndoor Hi/Mi/LodB-A
Indoor air temperatureISO(50Hz) : 27˚C DB/19.0˚C WB, ISO(60Hz) : 27.0˚C DB/19.5˚C WB
Outdoor air temperature ISO : 35.0˚C DB/24.0˚C WB
2-1Samsung Electronics
Table (cont.)
Item
Power Sourse
Performance
Electrical
Rating
Features
Dimensions
&
Weight
Model
Capacity (ISO/SASO)kcal/h
BTU/h
2
Air circulation (High)m
Moisture removal (High)Liters/h
Available voltage rangeV
Running amperesA
Power inputkw
Power factor%
Energy efficiency ratioBTU/wh
Compressor locked rotor amperesA
Controls/Temperature control
Control unit
Timer
Fan speedIndoor/Outdoor
Airflow direction (indoor)Horizontal
Comperssor
Refrigerant/Amount charged at ratingg
Refrigerant control
Operation soundIndoor Hi/Mi/LodB-A
Air circulation (High)m
Moisture removal (High)Liters/h
Available voltage rangeV
Running amperesA
Power inputkw
Power factor%
Energy efficiency ratioBTU/wh
Compressor locked rotor amperesA
Controls/Temperature control
Control unit
Timer
Fan speedIndoor/Outdoor
Airflow direction (indoor)Horizontal
Comperssor
Refrigerant/Amount charged at ratingg
Refrigerant control
Operation soundIndoor Hi/Mi/LodB-A
Indoor air temperatureISO(50Hz) : 27˚C DB/19.0˚C WB, ISO(60Hz) : 27.0˚C DB/19.5˚C WB
Outdoor air temperature ISO : 35.0˚C DB/24.0˚C WB
Samsung Electronics2-4
2-2 Major Component specifications
■
Indoor unit
PCB
Fan
&
Fan Motor
S-Motor
Heat
Exch.
■
Outdoor unit
Comp-
ressor
Fan
&
Fan
Heat
Exch.
Model
Part No.
Controls
Control circuit fuse
Type
Dia. and lengthmm
Fan motor model
Pols,rpm(at 240V)
Normal outW
Coil resistance(Ambient temp.20˚C)Ω
Safety devices Type
Operating temp. Open˚C
Run capacitorµF x VAC
Type
Model
Rating
Coil resistance (Ambient temp. 25˚C)Ω
Coil
Rows x Steps
Fin pitchmm
Face aream
Model
Type
Compressor model
Normal outputW
Comperssor oil kind
Comperssor oilcc
Oil Specific gravity
Coil resistance(Ambient temp.25˚C)Ω
Safety devicesType
Overloal relay
Operating temp. Open˚C
Close˚C
Operating amp(Ambient temp.)
Run capacitorµF x VAC
Type
Dia. and lengthmm
Fan motor model
Pols, rpm(at240V)
Normal outputW
Coil resistance(Ambient temp.20˚C)Ω
Safety devicesType
Operating temp. Open˚C
Close˚C
Run capacitorµF x VAC
Coil
Rows x Steps
Fin pitchmm
Face aream
Controls
Control circuit fuse
Type
Dia. and lengthmm
Fan motor model
Pols,rpm(at 240V)
Fan
Normal outW
&
Fan Motor
S-Motor
Heat
Exch.
■
Comp-
ressor
Coil resistance(Ambient temp.20˚C)Ω
Safety devices Type
Operating temp. Open˚C
Run capacitorµF x VAC
Type
Model
Rating
Coil resistance (Ambient temp. 25˚C)Ω
Coil
Rows x Steps
Fin pitchmm
Face aream
Outdoor unit
Model
Type
Compressor model
Normal outputW
Comperssor oil kind
Comperssor oilcc
Oil Specific gravity
Coil resistance(Ambient temp.25˚C)Ω
Safety devicesType
Overloal relay
Operating temp. Open˚C
Operating amp(Ambient temp.)
Run capacitorµF x VAC
Type
Dia. and lengthmm
Fan motor model
Pols, rpm(at240V)
Fan
Normal outputW
&
Coil resistance(Ambient temp.20˚C)Ω
Fan
Safety devicesType
Operating temp. Open˚C
Run capacitorµF x VAC
Coil
Rows x Steps
Heat
Exch.
Fin pitchmm
Face aream
2
Close˚C
Close˚C
2
AQ24A(B)5(6)RBD
PD-SH30ZC-02
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-9430SKC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5˚C
2µF x 450VAC
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.2
0.315
UQ24A(B)5(6)RBD
Rotary
55A240IUZEM
2220
SUNISO-4GSDT
800
0.92
Common to main : 1.84
-
3HM605-41
Internal Line Break
135
74
95˚F(35˚C)
40µF x 450VAC
Propeller
ø460
OSM-906SRC
6P, 850/400 RPM
70W
MAIN : 55Ω
SUB : 65Ω
17AM037A5
150±5˚C
-
4µF x 450VAC
AL-FIN / Copper tube
2 x 24
1.7
0.5376
AQT18A(B)9RE/AQT18A(B)02RE
PD-SH30ZC-02
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-9430SKC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5˚C
2µF x 450VAC
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.5
0.315
UQT18A9RE/UQT18A0RE
Reciprocating
AWG5524EXC
2030
WITCO LP200 OR EQUIVALENT
INITIAL : 1125 REFILL : 1066
0.92
Common to main : 2.98
Common to sub: 1.42
15HM2416-148
Internal Line Break
120
69
73.0 AT 2-10 SECOND
35µF x 450VAC
Propeller
ø405
ASS030AVEB
4P, 950/500 RPM
35W
MAIN : 180Ω
SUB : 200Ω
17AM034A5
135±5˚C
-
2.5µF x 450VAC
AL-FIN / Copper tube
2 x 24
1.7
0.504
AQT18C0REF
PD-SH30ZC-02
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-9430SKC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5˚C
2µF x 450VAC
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.5
0.315
UQT18C0REF
Rotary
55A200JT1EM
1920
SUNISO-4GSDT
650
0.92
Common to main : 1.14
Common to sub: 4.13
3HM532-41
Internal Line Break
135
74
95˚F(35˚C)
45µFx450VAC
Propeller
ø405
ASS030AVEB
4P, 950/500 RPM
35W
MAIN : 180Ω
SUB : 200Ω
17AM034A5
135±5˚C
-
3.0µF x 450VAC
AL-FIN / Copper tube
2 x 24
1.7
0.504
Samsung Electronics2-6
AQT18A(B)9RB/AQT18A(B)0RB/AQT18C9(0)RB
PD-SH30ZC-00
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-9430SKC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5°C
2µF x 450VAC
AQ18A(B)9RE/AQ18A(B)0RE/SH18ZA(B)9
PD-SH30ZC-00
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-94309KC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5°C
2.0µF x 450VAC
AQ18A(B)9(0)RBD
PD-SH30ZC-00
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-94309KC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5°C
2.0µF x 450VAC
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.5
0.315
UQT18AB(9)RB/UQT18A(B)0RB/UQT18C9(0)RB
Reciprocating
AWG5520EXN
2070
WITCO LP200 OR EQUIVALENT
INITIAL : 1125 REFILL : 1066
0.92
Common to main : 2.72
Common to sub : 1.32
15HM2311-148
Internal Line Break
120
69
73.0 AT 2-10 SECOND
25MF x 370VAC
Propeller
ø405
ASS030ZTEC
4P, 950/500 RPM
35W
MAIN : 160Ω
SUB : 170Ω
17AM034A5
135±5˚C
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.5
0.315
UQ18A(B)9RE/UQ18A(B)0RE/SH18ZA(B)9X
Rotary
48B180JV1EH
1885
SUNISO-4GSD-T
600
0.92
Common to main : 1.84
Common to sub : -
RAC12016-9622
External Line Break
165˚C
74˚C
120°C : 10.7A 130°C : 9.4A
40µF x 450VAC
Propeller
ø405
ASS030AVEB
4P, 950/500 RPM
35W
MAIN : 180Ω
SUB : 200Ω
17AM037A5
135±5˚C
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.5
0.315
UQ18A(B)9(0)RBD
Rotary
48D190IU1EH
1769
SUNISO-4GSD
600
0.92
Common to main : 1.84
-
RAC12016-9622
External Line Break
165˚C
74˚C
95˚F(35˚C)
40µF x 450VAC
Propeller
ø405
ASS030ZTEC
4P, 950/500 RPM
35W
MAIN : 180Ω
SUB : 200Ω
17AM037A5
135±5˚C
2.5µF x 450VAC
AL-FIN / Copper tube
2 x 24
1.7
0.504
2.5µF x 450VAC
AL-FIN / Copper tube
2 x 24
1.7
0.504
2.5µF x 450VAC
AL-FIN / Copper tube
2 x 28
1.5
0.534
2-7Samsung Electronics
Major Component specifications (cont.)
■
Indoor unit
PCB
Fan
&
Fan Motor
S-Motor
Heat
Exch.
■
Outdoor unit
Comp-
ressor
Fan
&
Fan
Heat
Exch.
Model
Part No.
Controls
Control circuit fuse
Type
Dia. and lengthmm
Fan motor model
Pols,rpm(at 240V)
Normal outW
Coil resistance(Ambient temp.20˚C)Ω
Safety devicesType
Operating temp. Open˚C
Run capacitorµF x VAC
Type
Model
Rating
Coil resistance (Ambient temp. 25˚C)Ω
Coil
Rows x Steps
Fin pitchmm
Face aream
Model
Type
Compressor model
Normal outputW
Comperssor oil kind
Comperssor oilcc
Oil Specific gravity
Coil resistance(Ambient temp.25˚C)Ω
Safety devicesType
Overloal relay
Operating temp. Open˚C
Close˚C
Operating amp(Ambient temp.)
Run capacitorµF x VAC
Type
Dia. and lengthmm
Fan motor model
Pols, rpm(at240V)
Normal outputW
Coil resistance(Ambient temp.20˚C)Ω
Safety devicesType
Operating temp. Open˚C
Close˚C
Run capacitorµF x VAC
Coil
Rows x Steps
Fin pitchmm
Face aream
AQT24A(B)5(6)RED/SH24TA(B)6D
2
UQT24A(B)5(6)RED/SH24TA(B)6DX
WITCO LP200 OR EQUIVALENT
2
PD-SH30ZC-00
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-9430SKC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5°C
2µF x 450VAC
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.2
0.315
Reciprocating
AWG5532EXC
2660
INITIAL : 1125 REFILL : 1066
0.92
Start winding : 2.49
Run winding : 0.81
15HM2415-148
Internal Line Break
120
69
73.0 AT 2-10 SECOND
45MF x 370VAC
Propeller
ø460
OSME-906SRC
6P, 850/400 RPM
70W
MAIN : 55Ω
SUB : 60Ω
17AM037A5
150±5°C
4µF x 450VAC
AL-FIN / Copper tube
2 x 28
1.5
0.543
AQ18A(B)9(0)RE(B)D/SH18ZA(B)0D
PD-SH30ZC-00
Microprocessor
250V, 3.15A
Cross-Flow
ø95/L = 842
IC-94309KC7A
4P, 1350 RPM
40W
MAIN : 137Ω
SUB : 132Ω
17AM034A5
135 ± 5°C
2.0µF x 450VAC
MSFCC20A03
DC 12V
530Ω
AL-FIN/Copper tube
2 x 15
1.5
0.315
UQ18A(B)9(0)RED/SH18ZA(B)0DX
Rotary
48B180JV1EH
1885
SUNSO-4GSD-T
600
0.92
Common to main : 1.84
Common to sub : -
RAC12016-9622
External Line Break
165°C
74°C
120°C : 10.7A 130°C : 9.4A
40µF x 450VAC
Propeller
ø405
ASS030AVEB
4P, 950/500 RPM
35W
MAIN : 180Ω
SUB : 200Ω
17AM037A5
135±5°C
2.5µF x 450VAC
AL-FIN / Copper tube
2 x 28
1.5
0.504
Samsung Electronics2-8
2-3 Dimensions
2-3-1 Indoor Unit
(Front view)
(Remote control)
(Rear view)
2-3-2 Outdoor Unit
2-3-2(a) 24K BTU
275
1080204
✳The feature is subject to be varied as a model.
115
2245
(Front view)(Rear view)
310
638
660
880
2-9Samsung Electronics
Product Specifications
2-3-3(b) 18K BTU
320
(Front view)(Rear view)
620
582
787
340
Samsung Electronics2-10
2-4 Pressure Graph
■ 24K BTU
G)
2
Low pressure(kg/cm
Outdoor inlet air D.B.temp.(˚C)
■ 18 BTU
G)
2
Low pressure(kg/cm
Outdoor inlet air D.B.temp.(˚C)
2-11Samsung Electronics
MEMO
Samsung Electronics2-12
3. Operating Instructions and Installation
3-1 Operating Instructions
3-1-1 The Feature of Key in remote controller
NO
NAMED OF KEY
1
(UP)
2
(DOWN)
3
4
5
Power On/Off button to start and stop airconditioner or timer set up.
Temp. up button. To increase the temperatute by the pressing
the temperature button.
Temp. down button. To decrease the temperature by the pressing
the temperature button.
Each time you press this button
Mode is changed in the following order
Press until the appearance. the air condition cools or heats
the room as quickly as possible. after 30minutes, the air,
the airconditioner is reset automatically to the previous mode.
Press until the appearance. the sleep timer can be used when
you are cooling or heating your room to switch the air conditioner off
automatically after a perriod of six hours.
Each time you press this button,
FAN SPEED is changed in the following order.
FUNCTION OF KEY
: Auto Mode: Fan Only
: Cool Mode: Heat Mode
: Dry Mode
6
7
8
9
Adjust air flow vertically.
The ON Timer enables you to switch onthe air conditioner automatically
after a given period of time that is from 30 minutes to 24 hours.
To cancel, press the (Set/Cancel) button.
The Off Timer enables you to switch off the air conditioner automatically
after a given period of time that is from 30 minutes to 24 hours.
To cancel, press the (Set/Cancel) button.
To select the 5 way function with the remote control, press the 5 way
button one or more times until the desired mode is selected.
Each time you press the 5 way button
Each 5 way indicator on the indoor unit comes on in order.
3-1Samsung Electronics
Operating Instructions and Installation
3-1-2 Name & Function of Key in remote controller
1. AUTO MODE : In this mode, operation
mode(COOL, HEAT) is selected automatically by the room temperature of initial
operation.
Room Temp
Tr≥ 21˚C+∆T
21˚C +∆T>Tr
∆T= -1˚C, -2˚C, 0˚C+1˚C+2˚C
∆T is controlled by setting temperature
up/down key of remote controller
2. COOL MODE : The unit operates according
to the difference between the setting and
room temperature. (18˚C~30˚C)
3. HEAT MODE : The unit operates according
to the difference between the setting and
room temperature.(16˚C~30˚C)
*Prevention against cold wind : For about
3~5 minutes after initial operation, thermo
control or “de-ice”, the indoor fan will
either not operate or operate very slowly,
then switch to the selected fan speed. This
period is to allow the indoor unit's heatexchanger to prewarm before emitting
warm air.
*High temperature release function : The
outdoor unit for and compressor ON/OFF
control for safety operation, when the overheat is heat exchanger of indoor unit.
*De-ice : Deicing operation is controlled by
indoor unit's heat exchanger temperature
and accumulating time of compressor's
operation.
De-ice end by sensing of the processing
time by de-ice Condition.
Cool Operation (Set Temp : 24˚C+∆T)
Heat Operation (Set Temp : 22˚C+∆T)
Operation Type
4. DRY MODE : Has 3 states, each determined
by room temperature.
The unit operates in DRY mode.
*Compressor ON/OFF Time is controlled
compulsorily(can not set up the fan speed,
always breeze).
*Protective function : Low temperature
release. (Prevention against freeze)
5. TURBO MODE : This mode is available in
AUTO, COOL, HEAT, DRY, FAN MODE.
When this button is pressed at first, the air
conditioner is operated “powerful” state for
30 minutes regardless of the set temperature, room temperature.
When this button is pressed again, or when
the operating time is 30 minutes, turbo
operation mode is canceled and returned to
the previous mode.
*But, if you press the TURBO button in DRY
or FAN mode that is changed with AUTO
mode automatically.
6. SLEEP MODE : Sleep mode is available
only in COOL or HEAT mode.
The operation will stop after 6 hours.
*In COOL mode : The setting temperature
is automatically raised by 1˚C each 1hour
When the temperature has been raised by
total of 2˚C, that temperature is maintained.
*In HEAT mode : The setting temperature
is automatically droped by 1˚C each 1hour.
When the temperature has been droped by
total of 2˚C, that temperature is maintained.
7. FAN SPEED : Manual (3 step), Auto (4 step)
Fan speed automatically varies depending
on both the difference between setting and
the room temperature.
Samsung Electronics3-2
Operating Instructions and Installation
8. COMPULSORY OPERATION :
For operating the air conditioner without
the remote controller.
*AUTO : The operating is the same function that AUTO MODE in the remote controller. And each time you press the button
the 5WAY func-tion is changed as follow.
STD ➝ NATURE ➝ POWER ➝ SAVING ➝
SILENCE ➝ POWER OFF
❊ STD(standard)( ) : General operation
Mode
❊ NATURE( ) : The unit is operated
according to health
pattern control
❊ POWER( ) : The unit is operated in
powerful state
❊ SAVING( ) : The unit is operated in
power saving state
❊ SILENCE( ) : The unit is operated
quitely
Each mode has Auto, Cool and SLEEP operation designed in advarce.
OFF TIMER : The air Conditioner is turned
OFF at a specified time using .
*ON TIMER : Only timer LED lights on.
*OFF TIMER : Both timer and operation
LED lights on.
11. SELF Diagnosis
LED DISPLAY
TIMER
STD
Check Point
Indoor unit room temperature sensor
error(open or short)
Indoor unit heat exchanger temperature
sensor error(open or short)
Indoor fan mal function
EEPROM error
Option error(option wasn’t set up or
option data error)
NATURE POWER SAVING SILENCE
9. SWING : BLADE-H is rotated vertically by
the stepping motor.
*Swing Set : Press the button under the
remote control is displayed on LCD the
and the blades move up and down. If the one
more time press the button, blades location is stop.
10. 24-Hour ON/OFF Real Setting Timer. : The
air conditioner is turned ON at a specified
time using .
LED
:
blinking
: LED off
12. BUZZER SOUND : Whenever the ON/OFF
button is pressed or whenever change
occurs to the condition which is set up or
select, the compulsory operation mode,
buzzer is sounded "beep".
3-3Samsung Electronics
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.