SAMSUNG TXP2011T-XAP Service Manual

Specifications

Alignment and Adjustments

Exploded View & Part List

Electrical Part List

PCB Diagram

Schematic Diagrams

COLOR TELEVISION RECEIVER

Chassis : KS9A(N) Model : TXP2011T/XAP

SERVICE

Manual

COLOR TELEVISION RECEIVER CONTENTS

This Service Manual is a property of Samsung Electronics Co.,Ltd.

Any unauthorized use of Manual can be punished under applicable

International and/or domestic law.

Printed in Korea

AA82-02249A

ELECTRONICS

Specifications

Samsung Electronics 1-1

1. Specifications

Broadcasting System

Regions

Tuning System

Intermediate Frequency

Power Supply

NTSC

North America

Electronic Remote Control System VHF (CH 2 ~ 13) UHF (CH 14 ~ 69)

CATV (CH 1, 14 ~ 125) VHF, UHF 75 unbalanced Video : 45.75 MHz Sound : 41.25 MHz

Chrominance Subcarrier: 42.17 MHz

ANTENNA INPUT RESISTANCE

Receiving Channels

South Central America MEXICO

AC 120V, 60Hz AC 100~240V, 60Hz AC 120V, 60Hz

MEMO

1-2 Samsung Electronics

Alignment and Adjustments

Samsung Electronics 2-1

2. Alignment and Adjustments

2-1 General Alignment Instructions

1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus.

2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below.

3. Use the specified test equipment or its equivalent.

4. Correct impedance matching is essential.

5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results.

6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.

7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.

8. To protect against shock hazard, use an isolation transformer.

2-2 Automatic Degaussing

A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation.

The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes.

If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF.

If color shading persists, perform the following Color purity and Convergence adjustments.

2-3 High Voltage Check

CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).

1. Connect a digital voltmeter to the second anode of the picture tube.

2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current).

3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 30 KV under any conditions.

Alignment and Adjustments

2-2 Samsung Electronics

2-4 FOCUS Adjustment

1. Iput a black and white signal.

2. Adjust the tuning control for the clearest picture.

3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.

2-5 Factory Adjustment

1. To enter the “Service Mode”, Press the remote-control keys in this sequence :

- If you do not have Factory remote-control

- If you have Factory remote-control

2-5-1 Service Mode

2-5-2 Factoy Mode OSD

ADJUST OPTION CHCKSUM RESET

T-FMTNUS-0000

2-5-2 ADJUST

PICTURE OFF PICTURE ON

MUTE 1 8 2

PICTURE ON

DISPLAY

)

(

FACTORY

+ 14 hidden pages