Samsung TXN2771HFX, TXN2771HFXAC, TXN2670WHFXXAA, TXN2771HFXAA Service Manual

COLOR TELEVISION RECEIVER

Chassis : K55A

Model : TXN2771HFX/XAA

TXN2771HFX/XAC TXN2670WHFXXAA

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Reference Information

Specifications

Alignment and Adjustments

Exploded Views and Parts List

Electrical Parts List

Troubleshooting

Block Diagrams

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

ELECTRONICS

Printed in Korea

AA82-00406A

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGE CURRENT

TESTER

DEVICE UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

EARTH

GROUND

(READING SHOULD

NOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning: The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

Precautions

Samsung Electronics 1-3

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between

the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

Precautions

1-4 Samsung Electronics

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Reference Information

Samsung Electronics 2-1

2. Reference Information

2-1 Tables of Abbreviations and Acronyms

A Ah Å dB dBm

°C °F °K F G GHz g H Hz h ips kWh kg kHz kΩ km km/h kV kVA kW I MHz

Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz

MV MW MΩ m µA µF µH µm µs µW mA mg mH mI mm ms mV nF

Ω

pF Ib rpm rps s V VA W Wh

Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour

Table 2-1 Abbreviations

Reference Information

2-2 Samsung Electronics

Table 2-2 Table of Acronyms

ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF

Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency

I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR

Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor

Reference Information

Samsung Electronics 2-3

2-2 IC Line Up

Block Des-Loc Part-Number IC Name Description

MAIN

IC901

HIC401

TU02S

IC06

IC805

HC401

D801S

HC801

IC602

IC801S

IC301

IC902

IC401

IC803

AA09-00041A

AA13-00094A

AA40-00041A

1203-002000

1203-001006

0502-001230

0402-001399

1230-001006

1201-001385

1203-002512

1204-000517

1103-001177

1202-000103

1203-001225

SDA555X-OTP

DDRI001A

TCPN3081PC09C(S)

DETECTOR;7027

78R05)

FJL6920YDTU)

GSIB660

78R05

7269A

KA5Q1565RF

LA7845

24WC16

393, DIP, 8P

78R09

IC-MCU

IC HYBRID

TUNER-F/S

IC-VOL

IC-VOLTAGE REGULATOR

TR-POWER

DIODE-BREDGE

IC-VOLTAGE REGULATOR

IC-POWER AMP

IC-PWM CONTROLLER

IC-VERTICAL DEF

IC-EEPROM

IC-VOLTAGE COMP

IC-POSI.FIXED REG

F-BOX

IC601

TU01S

IC402

IC804

IC904

IC202

Q402

IC903

IC06

IC11

IC03

IC10

IC08

IC05

1204-001970

AA40-00020A

1203-000243

1203-001217

1203-001943

1203-001944

0505-001116

1203-001944

1203-002000

0801-000662

1001-001082

1001-001177

1203-001419

1203-002186

MSP3421G0P0-8

TCLN3181PA09A(S)

7812A

431

7025

78RM33

BUZ73A

78RM33

7027

74HC123

BA7657F

TEA6425D

4931

18, DPAK

IC-SOUND PROCESSOR

TUNER-F/S

IC-POSI.FIXED REG

IC-POSI.ADJUST REG

IC-VOL DETECTOR

IC-POSI.FIXED REG

FET-SILICON

IC-POSI.FIXED REG

IC-VOL DETECTOR

IC-CMOS LIGIC

IC-VIDEO SWITCH

IC-VOLTAGE REGULATOR

IC-POSI.FIXED REG

Reference Information

2-4 Samsung Electronics

Block Des-Loc Part-Number IC Name Description

F-BOX

29"34"

CRT

32"

CRT

IC07

IC02

IC09

IC01

IC04

QF10

QF09

IC501

IC502

IC503

IC504

IC505

QF10

QF09

1203-002351

1204-001814

1204-001935

1204-001938

1204-001989

0502-000153

0502-000131

1201-001131

1201-000010

1203-000165

0502-000153

0502-000131

LF25C

CXA2151Q

UPD64083GF

VSP9407B-B11

CXA2165Q

SC2344-D

2SA1011-D

6111Q

2030

78R12

2SC2344-D

2SCA1011-D

IC-VOLTAGE REGULATOR

IC-SELECTOR

IC-SEPARATOR

IC-DECODER

IC-VIDEO PROCESS

TR-POWER

TR-POWER;

IC-VIDEO AMP

IC-OP AMP

IC -POSI.ADJUST REG

TR-POWER

IC501

IC502

IC503

IC504

1201-001588

1201-000010

6120Q

2030

IC-VIDEO AMP

IC-OP AMP

Specifications

Samsung Electronics 3-1

3. Specifications

Broadcasting System

Tuning System

Intermediate Frequency

Power Supply

NTSC-M

VHF (CH 2 ~ 13) UHF (CH 14 ~ 69)

CATV (CH 1, 14 ~ 125) VHF, UHF 75 unbalanced Video: 45.75 MHz Sound: 41.25 MHz

Chrominance Subcarrier: 42.17 MHz AC 120V, 60Hz

Electronic Remote Control System

ANTENNA INPUT RESISTANCE

Receiving Channels

3-2 Samsung Electronics

MEMO

Alignment and Adjustments

Samsung Electronics 4-1

4. Alignment and Adjustments

4-1 Adjustments

Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for good black and white details. There must be no objectionable color shading: If color shading is present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments.

Note :

1. This ‘4. Alignment and Adjustments’ applies to KS4A chassis applications.

2. AC Power Supply: 220 V only

3. This service manual has been written on the basis of domestic remote-control model adopting KS4A chassis. Depending on sales location and product specifications, some of specifications herein may be changed.

KS4A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust in the following sequence:

4-1-1 General Alignment Instructions

4-1-2 Focus Adjustment

Dynamic Focus Adjustment

1. Input a crosshatch pattern.

2. Select “Standard” from the menu,

3. Turn the Static Focus VR clockwise to set it to its maximum.

4. Turn the Dynamic Focus VR counterclockwise to set it to its maximum.

5. Turn the Static Focus VR counterclockwise slowly for the clearest center vertical line.

6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.

7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6.

V

STATIC FOCUS VR

H

DYNAMIC FOCUS VR

NO USE

After Adjustment

1 2

3

Alignment and Adjustments

4-2 Samsung Electronics

4-1-3 Screen Voltage Adjustment

1. Enter the Service Mode by pressing the remote control keys in the following sequence

: Power Off Mute 1 8 2 Power On

2. Initialize all set data.

3. Input a Toshiba pattern.

4. Use an oscilloscope to identify RK, BK, GK. And then adjust FBT Screen VR so that the voltage of

pedestal level doesn’t exceed 175V. If a Toshiba pattern is not available, cancel the blue screen and input “No Signal” to AV IN so the voltage of pedestal level doesn’t exceed 188V. If an oscilloscope is not available, use a DC multi-meter in No Signal (black screen) to adjust RK, BK, GK so that the highest voltage becomes 175Vp-p.

4-1-4 White Balance Adjustment

1. Warm up the TV set for at least 30 minutes.

2. Enter the Service Mode by pressing the remote control keys in the following sequence: Power Off -> Mute 1 8 2 Power On

3. Initialize all set data.

4. Input a Toshiba pattern.

5. Using a probe (CA100), do the White Balance adjustments.

a) Adjust Low-Light.

- Adjust Sub Brightness to set Y.

- Adjust B Cutoff to set y.

- Adjust R Cutoff to set x.

b) Adjust High-Light.

- Adjust Sub Contrast to set Y.

- Adjust B Drive to set y.

- Adjust R Drive to set x.

c) Check the value of Low-Light. If necessary, readjust Low-Light.

d) Check the value of High-Light. If necessary, readjust High-Light.15

Alignment and Adjustments

Samsung Electronics 4-3

4-1-5 When adjusting Screen Voltage and White Balance

1. Screen Voltage and White Balance are related each other. Make sure both adjustments are correct.

2. Adjust Screen Voltage before White Balance Adjustments. Make sure Screen Voltage is correct.

3. If White Balance has been readjusted, re-check Screen Voltage.

4. After adjustments are complete, check the following.

- If spots appear on the screen after pressing the Power On/Off key, readjust Screen Voltage.

- If flyback lines appear on the screen, readjust Screen Voltage.

Alignment and Adjustments

4-4 Samsung Electronics

4-2 MICOM PORT

PIN FUNCTION

1

W-PORT

2

ROM SDA

3

ROM SCL

4

BUS-STOP

5

MAIN SDA

6

MAIN SCL

7

S-RESET

8

V-RESET

9

VDD 2.5V

10

11

12

13

14

15

16

17

GND

VDD 3.3V

CVBS IN

VDD 2.5V

GND

AFT

SC1-ID

SC-2-ID

FIRST STATE

HIGH

SERIAL H

HIGH

SERIAL H

HIGH

IV p-p

HIGH

- RESET Control jack during E2PROM latch UP (Function: Low)SERIAL H

- E2PROM only SDA LINE

- E2PROM only SCL LINE

- Automation and after-sales service related BUS STOP (STOP: LOW)

- CXA2150Q / CXA2151Q /VSP940X / BA7657F / MSP34XX / TUNER Control jack

- Reset when MSP34XX IC (SOUND PROCESS IC) has an error (Active: LOW)

- Reset when VSP940X IC (1-chip IC) has an error

- Analog GND

- TTX and USA Caption Input source Line ( 1V p-p)

- Main AFT Control jack ( 0 - 3.3V)

AV MODE

4 : 3 MODE

RANGE

TV MODE

0 ~ 2V 4.5 ~ 7V 9.5 ~ 12V

16 : 9 MODE

18

19

20

21

22

23

24

25

26

27

28

29

30

31(33)

32(34)

33(35)

34(36)

35(37)

36(38)

37(39)

KEY-1

H-SYNC

V-SYNC

KEY-3

KEY-2

X-RAY

IR-IN

STD-LED

TIM-LED

RELAY

SW1

GND

VDD 3.3V

RESET

X-IN

X-OUT

GND

VDD 2.5V

OSD-R

OSD-G

HIGH

POSITIVE

HIGH

LOW

HIGH

LOW

HIGH

1.2V p-p

MENU

PHILIPS 0 ~ 0.1V 0.1 ~ 0.7V

- MICOM "H-SYNC" Input, POSITIVE Input (3.3 V p-p)

- MICOM "V-SYNC" Input, POSITIVE Input (3.3 V p-p)

- Power ON/OFF Control jack

- TV/VIDEO switching control jack

- Function: Low

- Remote Control Input Jack

- STANDBY: Hight, OFF: LOW

- TIME ON: H TIME OFF: L

- DEGAUSSING COIL CONTROL: Based on standard specifications

- H: IN1, L: IN2 (BA7657F) PIN (#16) Control jack

- Reset active : HIGH

- Crystal oscillation input jack

- Crystal oscillation output jack

- OSD R-OUT OUTPUT jack (0.38V p-p) ,half tone: 0.9V p-p

- OSD G-OUT OUTPUT jack (0.38V p-p) ,half tone: 0.9V p-p

VOL-

VOL+

0.7V ~ 13V 1.3V ~ 1.9V 0.9 ~ 2.4V

CH- CH+

Alignment and Adjustments

Samsung Electronics 4-5

PIN FUNCTION

37(40)

38(41)

39(42)

40(43)

41(44)

42(45)

43(46)

44(47)

45(48)

46(49)

47(50)

48(51)

49(52)

OSD-B

CORE

VDD 2.5V

GND

VDD 3.3V

PX, Y

SW3

SW2

S-MUTE

POWER

H.P-ID

TILT

FIRST STATE

1.2V p-p

0.9V p-p

HIGH

H

L

HIGH

ASSIGNMENT

- OSD B-OUT OUTPUT jack (0.38V p-p) ,half tone: 0.9V p-p

- OSD F/B OUTPUT jack (Clamped at SAND PULSE, Half Tone: "LOW")

- V-SYNC INPUT

- F/B INPUT JACK

F1

L

M

- System (NTSC/PAL) MUST be separated

- Active "LOW"

- 1080I control jack: 1080i (LOW), RF (High)

- Magnetic field control

F0

M

L

fH

1.75KHz (480i/480P)

33.75KHz (1080i)

LOW: GNDHIGH : OPEN STATUS

Initially, these pins select an input

source at LOW state

4-3-1 Factory Adjustment Values

Alignment and Adjustments

4-6 Samsung Electronics

4-3 Factory Adjustment Values and White Balance Settings

SERVICE

Deflection 480P Offset 1080i Offset PC Offset Video Adjust 1 Video Adjust 2 Option (2EH 00H) Reset

4-3-2 White Balance Settings

W/B

Value

Model

H

L

INCH

SDI CRT

TXM2796HFX TXM2796HFX TXM2798HFX

275/265 45FL

275/265 1.0FL

LG CRT TOSHIBA CRT

32" WIDE29" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

275/265 50FL

275/265 1.5FL

34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

275/265 40FL

275/265 1.0FL

SDI CRT SDI CRT SDI CRT SDI CRT

32" WIDE 32" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

275/265 45FL

275/265 1.0FL

34" FLAT 29" FLAT 34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

275/265 40FL

275/265 1.0FL

CT29Z7PGX CT32Z7PGX CT34Z7PGX

275/265 45FL

275/265 1.0FL

275/265 45FL

275/265 1.0FL

TOSHIBA CRT

275/265 40FL

275/265 1.0FL

: Fixed Value

Alignment and Adjustments

Samsung Electronics 4-7

4-4 Functions of Each Port in Service Mode

DEFLECTION

V-AMP

V-SHIFT

H-EW

H-SHIFT

V-LIN

UP-LIN

LOW-LIN

V-SC

H-PAR

UP-COR

LOW-COR

H-TRA

BOW

ANGLE

V-POSI

CXA Left BLK

CXA Right BLK

SDI CRT

TXM2796HFX TXM2796HFX TXM2798HFX

TXM3096HFX TXM3097HFX TXM3098HFX

TXM3296HFX TXM3297HFX TXM3298HFX

TXM3096HFX TXM3097HFX TXM3098HFX

TXM3296HFX TXM3297HFX TXM3298HFX

CT29Z7PGX CT32Z7PGX CT34Z7PGX

INCH

ITEM

Model

32" WIDE29" WIDE

LG CRT TOSHIBA CRT

34" FLAT

32" WIDE 32" WIDE

34" FLAT 29" FLAT 34" FLAT

SDI CRT SDI CRT SDI CRT SDI CRT

TOSHIBA

CRT

45

26

46

27

5

6

3

24

27

26

37

32

30

37

30

25

6

4

3

32

35

30

32

30

37

50

28

30

25

5

7

3

40

35

45

32

30

37

30

6

4

3

32

35

30

32

30

37

42

29

20

31

10

15

5

45

38

41

28

31

30

32

30

37

45

26

46

27

5

6

3

24

27

26

37

32

30

37

30

6

4

3

32

35

30

32

30

37

50

28

30

25

5

7

3

40

35

45

32

30

37

Alignment and Adjustments

4-8 Samsung Electronics

480P OFFSET

ITEM

V-AMP

V-SHIFT

H-EW

H-SHIFT

V-LIN

UP-LIN

LOW-LIN

V-SC

H-PAR

UP-COR

LOW-COR

INCH

Model

SDI CRT

TXM2796HFX TXM2796HFX TXM2798HFX

0

-2

7

8

0

LG CRT TOSHIBA CRT

32" WIDE29" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

0

-1

6

3

0

2

0

34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

2

-1

4

8

0

-2

0

SDI CRT SDI CRT SDI CRT SDI CRT

32" WIDE 32" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

0

-1

6

3

0

2

0

34" FLAT 29" FLAT 34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

1

0

4

0

-2

0

CT29Z7PGX CT32Z7PGX CT34Z7PGX

0

-2

7

8

0

TOSHIBA

0

-1

6

3

0

2

0

CRT

2

-1

4

8

0

-2

0

H-TRA

BOW

ANGLE

V-POSI

CXA Left BLK

CXA Right BLK

28

36

0

28

36

0

28

36

0

28

36

0

28

36

0

28

36

0

28

36

0

28

36

Alignment and Adjustments

Samsung Electronics 4-9

1080i OFFSET

ITEM

V-AMP

V-SHIFT

H-EW

H-SHIFT

V-LIN

UP-LIN

LOW-LIN

V-SC

H-PAR

UP-COR

LOW-COR

INCH

Model

SDI CRT

TXM2796HFX TXM2796HFX TXM2798HFX

-14

-5

8

1

0

-2

LG CRT TOSHIBA CRT

32" WIDE29" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

-13

-4

0

-1

0

-7

-3

-1

34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

-15

-4

10

-1

0

-3

0

SDI CRT SDI CRT SDI CRT SDI CRT

32" WIDE 32" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

-13

-4

0

-1

0

-7

-3

-1

34" FLAT 29" FLAT 34" FLAT

TXM3296HFX TXM3297HFX

CT29Z7PGX CT32Z7PGX CT34Z7PGX

TXM3298HFX

-12

-3

9

-1

0

7

-1

1

-14

-5

-2

-13

8

1

0

TOSHIBA

CRT

-15

-4

0

-1

0

-7

-3

-1

-4

10

1

0

-3

0

H-TRA

BOW

ANGLE

V-POSI

CXA Left BLK

CXA Right BLK

50

27

3

4

2

0

50

27

-3

0

50

27

-3

-2

0

50

27

-3

0

-3

50

27

3

1

0

4

2

0

50

27

-3

50

27

-3

0

-2

0

50

27

Alignment and Adjustments

4-10 Samsung Electronics

PC OFFSET

ITEM

V-AMP

V-SHIFT

H-EW

H-SHIFT

V-LIN

UP-LIN

LOW-LIN

V-SC

H-PAR

UP-COR

LOW-COR

H-TRA

BOW

ANGLE

V-POSI

CXA Left BLK

CXA Right BLK

INCH

Model

SDI CRT

TXM2796HFX TXM2796HFX TXM2798HFX

*

LG CRT TOSHIBA CRT

32" WIDE29" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

*

34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

*

SDI CRT SDI CRT SDI CRT SDI CRT

32" WIDE 32" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

*

34" FLAT 29" FLAT 34" FLAT

TXM3296HFX TXM3297HFX

CT29Z7PGX CT32Z7PGX CT34Z7PGX

TXM3298HFX

*

-22

0

-26

19

0

8

2

0

20

10

-16

-20

18

20

10

TOSHIBA CRT

-16

0

-21

16

0

4

5

2

0

7

2

0

20

10

Alignment and Adjustments

Samsung Electronics 4-11

VIDEO ADJUST 1

: Fixed Value

INCH

Model

ITEM

R-Cutoff

G-Cutoff

B-Cutoff

Color on/off

CR offset

CB offset

R-Drive

G-Drive

B-Drive

Sub-Bright

SDI CRT

TXM2796HFX TXM2796HFX TXM2798HFX

32

1

31

32

23

LG CRT TOSHIBA CRT

32" WIDE29" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

32

1

31

32

24

32

25

34" FLAT

TXM3296HFX TXM3297HFX TXM3298HFX

32

1

31

32

10

SDI CRT SDI CRT SDI CRT SDI CRT

32" WIDE 32" WIDE

TXM3096HFX TXM3097HFX TXM3098HFX

32

1

31

32

20

34" FLAT 29" FLAT 34" FLAT

TXM3296HFX TXM3297HFX

CT29Z7PGX CT32Z7PGX CT34Z7PGX

TXM3298HFX

32

1

31

32

10

32

1

31

32

23

TOSHIBA CRT

32

1

31

32

20

32

31

32

10

1

Sub-Contrast

Sub-Color

Sub-Tint

CTI-Level

COL AXIS

LTI-Level

PC DPIC Level

PC DC Trans

PC VM Level

10

18

10

18

7

1

2

1

*

7

1

2

1

*

10

18

10

18

7

1

2

1

*

7

1

2

1

*

18

5

7

1

2

1

*

10

18

10

18

7

1

2

1

0

7

1

2

1

0

10

18

7

1

2

1

0