SAMSUNG CXJ1331, CXJ1331AX, CXJ1331TUCX, CXJ1352, CXJ1352AX Service manual & schematics

...

Download

Page 1

Television Video Cassette Recorder

Chassis : V15A Model: TT20A54X/XAX TT20A54X/GSU

TT20A54X/RCL TT14A54X/XAX

SERVICE Manual

Television Video Cassette Recorder

1. Precautions
2. Specifications
3. Alignment and Adjustment (VCR)
4. Alignment and Adjustment (TV)
5. Timing Chart
6. Troubleshooting
7. Exploded View and Parts List
8. Electric Parts List
9. Block Diagram
10. Wiring Diagram
11. PCB Layout
12. Schematic Diagrams

Page 2

1. Precautions

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.
3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check

With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits:

High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be

reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Page 3

1-1 Safety Precautions (Continued)

High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.
10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty.
11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.
13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.
16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.
17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading, (A) or (A). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Page 4

1-2 Servicing Precautions

Warning 1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning 2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet. Follow them.
Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.
3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.
4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks).
6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.
8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.

Page 5

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.
2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power this is an electric shock precaution.)
3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.
4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.
8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.
9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

Page 6

2. Specifications

Format	VHS Standard
Recording System	Rotary, azimuth two-head or four-head helical scanning system Luminance : FM azimuth recording Color signal : converted subcarrier phase shift recording
Television System	NTSC-type color signal EIA standard (525 lines, 60 fields)
Audio Track	1 track
Tape Width	12.7 mm (1/2 inch)
Record Speed
SP	33.35 mm/s (1.31 in./s)
SLP	11.12 mm/s (0.43 in./s)
Record/Playback Time	480 min. with T-160 used in SLP mode
FF/Rew Time	Less than 100 sec. with T-120
Heads	Video : 2 rotary heads, 4 rotary head Audio/Control : 1 stationary head Erase : 1 full track erase 1 audio track erase
VIDEO
Input	VIDEO IN jack (RCA) 1.0Vp-p, 75 ohm unbalanced
Signal-to-Noise Ratio	Better than 35dB
Horizontal Resolution	Color/Monochrome: more than 220 lines
AUDIO
Input	AUDIO IN jack (RCA) -8dBm,50kohm unbalanced
Horizontal Resolution	Color/Monochrome : more than 220 lines
Frequency Response
SP : - 6dB SLP : - 6dB	100Hz - 10KHz 100Hz - 5KHz
TV Tuner	VHF input : Ch.2 - Ch.13, Cable channels 4A, A~W, W+1~W+84, A-5~A-1 75 ohm unbalanced UHF input : Ch.14-Ch.69 VHF,UHF one input 75 ohm unbalanced
Power Requirement	120V AC, 60Hz (USA/CANADA), 100V ~ 240V (LATIN)
Power Consumption	13 (14) Inch : Approx. 65 watts when on 19 (20) Inch : Approx. 80 watts when on
Operating Temperature	41°F - 104°F (5°C - 40°C)
Operating Humidity	10%-75%

Equipment specifications are subject to change without notice.

Page 7

3. Alignments and Adjustments (VCR)

3-1 Mechanical Adjustments

3-1-1 Tape Transport Adjustment

Note : The tape transport system was adjusted precisely in the factory, any adjustments is unnecessary except for:

♦ Noise on the screen.
✤ Tape damage.
Parts replacement in the tape transport system.

3-1-1(A) PARTS LOCATIONS

The lower flange height of tape guide is used as the reference height for the transport adjustment. To maintain the height of the tape guide, do not apply excessive force onto the main base.

Page 8

3-2 Adjustments

3-2-1 Preadjustment

1. When parts are replaced, the tape ran sport system may be changed. When many different parts are replaced, refer to the procedures for the tape transport system.

To begin run a T-120 tape and make sure that excessive tape wrinkle does not occur at each of the tape guides.

2. If tape wrinkle occurs at the S, T-guide rollers, turn the S, T-guide rollers until the tape wrinkle disappears.
3. If tape wrinkle still occurs at the tape guide, adjust the tilt of A/C head.
4. A/C head adjustment locations

Test Points : JM112-CTL (control waveform) JM113-H'D SW (head switching sync) JM114-EnV (envelope waveform) JM119-A.OUT (audio output) Test Tape : Color bar (1 KHz) Lion pattern(7 KHz)

3-2-2(A) A/C HEAD HEIGHT ADJUSTMENT
1. Run the alignment tape (Color bar) in the playback mode.
2. Observe surface of the audio head using a dental mirror.
3. Turn screw (C) clockwise or counterclockwise until the gap of lower tape edge and the lower edge of the control head is about 0.25mm (Refer to Fig. 3-4 and 3-5).

Fig. 3-4 Location of A/C Head Adjustment Screw

Page 9

3-2-2 (B) A/C HEAD TILT ADJUSTMENT

1. Playback a blank tape and observe the position of the tape at the lower flange of tape guide.
2. Confirm that there is no curl or wrinkle at the lower flange of tape guide as shown in (Fig. 3-6).
3. If a curl or wrinkle of the tape occurs, slightly turn the screw (A) tilt adjust on the ACE head ass'y.
4. Reconfirm the ACE head height.

Fig. 3-6 Tape Guide Check

3-2-2(C) AUDIO AZIMUTH ADJUSTMENT
1. Load alignment tape (Mono Scope) and play back a 7KHz signal.
2. Connect Ch1 scope probe to JM119(A-OUT).
3. Adjust A/C head azimuth adjustment screw B for maximum audio output level (see Fig. 3-4).

3-2-2(D) A/C HEAD POSITION (X-POINT) ADJUSTMENT

1. Load alignment tape (Mono Scope) and play back a 7KHz signal (SP Mode).
Connect Ch1 scope probe to JM119 (A-out), Ch2 scope probe to JM113-H'D SW Adjust sync to Channel 1.
3. 4HD Model : Set the control pulse to 6.5 msec using the Fine tracking buttons +/- on the remote control (see Fig. 3-8, 3-9).

2HD Model : 2.5msec (see Fig. 3-8, 3-9).

4. Connect Ch1 scope probe to JM114-ENV.
5. Insert the adjusting driver into the X-position adjusting gear and adjust the driver for maximum envelope waveform.

Note :

Do not adjust the X-point using excessive force. After turning the X-point adjusting screw (D) counterclockwise a little, perform the adjustment and then tighten the screw (See Fig. 3-4).

Fig. 3-7 Test Point Position (Main PCB : Parts)

Page 10

SCOPE SETTINGS

Fig. 3-8 (A) Tracking Preset Adjustment (4HD)

Fig. 3-9 Control Pulse Adjustment

3-2-2(E) LINEARITY ADJUSTMENT (GUIDE ROLLER S.T ADJUSTMENT)

Test Points : JM113-H'D SW (head switching sync) JM114-EnV (envelope waveform)

Fig. 3-10 Test Point Position (Main PCB : Parts)

1. Play back the Mono Scope alignment tape (SP Mode).
2. Observe the video envelope signal on the oscilloscope after taking sync with the video switching pulse.
3. Make sure that the video envelope meets the specifications of Fig. 3-11 (especially for minimum values).

Note :

a = Maximum output of the video RF envelope
b = Minimum output of the video RF envelope at the entrance side
c = Minimum output of the video RF envelope at the center point
d = Maximum output of the video RF envelope at the exit side

Fig. 3-11 Envelope Waveform Adjustment

Page 11

4. If Fig. 3-12 A does not meet the specification, adjust the S-guide roller up or down.
5. If Fig. 3-12 B does no meet the specification, adjust the T-guide roller up or down.

Fig. 3-12 Adjustment Points

6. Slightly loosen the set screw at the lower part of S, T-guide rollers using a hex wrench (diameter : 0.9mm), so that the guide rollers can be adjusted with reasonable tightness (Fig. 3-13).

7. Play back the Mono Scope alignment tape (SP Mode).
8. Connect CH1 to JM114 (ENV), and CH2 to JM113 (H'D) for taking sync (located on the same PCB).
9. Turn the guide roller head with a flat head screw driver (
10. After completing the adjustments, tighten the set screw.

Fig. 3-14 S, T-Guide Roller Height Adjustment

Page 12

3-2-3 Check Switch over from RPS to Playback Mode

Check the transition from RPS to playback mode using a pre-recorded SP tape. Make sure that the leading edge of envelope comes to an appropriate steady state within 3 seconds as shown in Fig. 3-15.
2. If the leading edge of envelope waveform does not meet the specification within 3 seconds, make sure that there is no gap between the S-roller lower flange and the tape. If there is a gap, readjust the S-guide roller.
3 Change operation from RPS to Play back Mode, and make sure that the leading edge

Fig. 3-15 Video envelope rise (when transiting from RPS to Playback mode)

3-2-4 Envelope Check

1. Make recordings on T-120 and T-160 tapes, and make sure that the playback output envelope meets the specification show in Fig. 3-16.
Play back a self recorded tape (use a T-120). The video envelope should meet the specification shown in Fig. 3-16. In SLP Mode, (A) should be the same as (B). If the head gap is wide, check the cylinder

Fig. 3-16 Envelope Output and Output Level Difference Playback mode)

3-2-5 Tape Wrinkle Check

1. Run the T-180 tape in playback, FPS, RPS and the Pause Modes, and observe the tape wrinkle at each guide.
2. If excessive tape wrinkle is observed during the above modes, do the following adjustments :

If tape wrinkle occurs at S, T-guide rollers, do a linearity adjustment. If tape wrinkle exists at the tape guide flange, do an A/C head assembly adjustment.

Page 13

3-3 Reel Torque Adjustments

1. The rotation of the capstan motor causes the Holder Clutch Ass'y to rotate through the Belt Pulley.
2. The spring wrap PLAY/REV of holder clutch ass'y drives the disk reel S, T through gear idle by rotation of gear center ass'y.
3. Brake is operated by slider cam at FF/REW mode.
4. Transportation of accurate driving force is done by gears (Gear Center Ass'y).
Note : If the spec. does not meet the followings specifications, replace the holder clutch ass'y and then recheck.

MODE	TO	RQUE g/cm	GAUGE
DD	NTSC	82.5 ± 27.5	Cassatta Tarquamatar
FD	PAL	79 ± 27	Casselle loidnemeter
RPS	145 ± 30		Cassette Torquemeter

Page 14

3-4 Location Adjustment and Confirmation of Tension Post

1. Remove the holder cassette ass'y and then push the lever FL Arm-R to the direction of loading.
2. Push the lever tension drive 1 in the direction of arrow. (See Fig. 3-17)
Turn the gear worm wheel 2 clockwise so that "Timing Point" of the slider FL drive 3 and gear FL cam 4 can be aligned (See Fig. 3-18).

Fig. 3-17

Fig. 3-18

4. As rotating Disk S Reel ① clockwise and the region of adjusting in the Main Base (in shape of slit) clockwise or counterclockwise after inserting screw driver in the slit on Main Base. Adjust the left end edge of Lever Tension Ass'y ③ to 1.3+1.5/-0.5mm from the location of mark in the Main Base.
As rotating Disk S Reel ①, double-check the location of the left end edge of Lever Tension Ass'y and the quantity of crossing from mark on Main Base. (+1.0/-0.5mm)

Counterclockwise : Torque UP Clockwise : Torque DOWN

Back Tension should be 56 ± 15g.cm at inspecting it with Back Tension Meter.

Fig. 3-19 Tension Pole and Back Tension Adjustment

Note :

1. Mark on Main Base is located in about 1.3mm from inside of bending line.
2. Be careful not to deform the region of adjusting on Main Base up and down at adjusting.

Page 15

3-5 Circuit (SERVO) Adjustment

3-5-1 Adjust the switching point.

1. Play back the SP standard tape.
2. Connect the oscilloscope CH1 to EYM03 (H'D) and CH2 to EYM11 (V.OUT)
3. Set the oscilloscope sync to CH1, and adjust VRM601 for 6.5H ± 0.5H waveform as shown in the figure.

Fig. 3-21

Fig. 3-20

Page 16

5. Timing Chart

5-1 Program S/W Timing Chart


POWER OFF	0	0	0	1	Unload Power Off
LOADING START	0	0	0	1	(Tape loading start point)
LOADING END	1	0 →1	1	1	(Tape loading end point)
REV	1	1	0	Х	Reverse Picture Search, Reverse SLOW
PLAY	0	1	0	Х	Play, Rec, F-PS, Still, SLOW, F-ADV
STOP1	0	0	1	1	Stop (Play position 5 Min, over)
STOP2	0	0	1	Х	(MAIN Break ON MODE)
FF/REV1	1	0	0	Х	High speed Rew, Low speed FF
FF/REV2	0	1	1	Х	High speed FF, Low speed REW

Page 17

6. Troubleshooting

6-1 No Power (No Raster, No Sound, Power Led Off)

Page 18

6-2 No Picture or Raster

Page 19

Page 20

6-4 No Vert Scan

6-5 No Color

Page 21

Page 22

Page 23

6-8 No Playback

Page 24

6-9 REC Doesn't Operate

6-10 "FF" Doesn't Operate

Page 25

6-12 "Forward Direction Search Screen" Doesn't Operate

Page 26

Page 27

Page 28

6-15 Capstan Doesn't Rotate

Page 29

Page 30

Page 31

Page 32

6-19 No Color During Playback

Page 33

Page 34

7. Exploded View & Parts List

7-1 TT14A54X

No	Code No.	Description;Specification	Q'ty	Remark
1	AA92-00002M	ASSY-CABINET,FRONT;TT14A5,MEX,V15A,14	1
1-1	AA64-70009D	BADGE-BRAND;-,AL,-,L40,GOLD,R2	1
1-2	3001-000281	SPEAKER-GENERAL;2.5W80HM77MM77	1
1-3	2001-001187	ASSY-PCB,A/V;-,KCV13A,V15A,13,19	1
1-4	L9100-0003	SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW	2	AV+CF
1-5	AA64-00018A	WINDOW-REMOCON;-,TT13/19A52,-,PC,VIOLET.	1
1-6	AA64-00012A	INDICATOR-LED;-,TT13/19A52,-,PC,-,CLEAR.	1
1-7	6003-000333	SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW	1	IL+CF
1-8	AA64-00011D	KNOB-FAMILY;-,TT14/20A5,PA100,ABS,HB,BLK	1
1-9	6002-000512	SCREW-TAPPING;RH,+,2,M4,L12,ZP	2	KF+CF
2	AA03-10001D	CRT-COLOR;-,A34KQV42X,+380MG,14,90DEG,5	1
2-1	L9400-0002	HOLDER-DEGAUSSING;20POLYVINIL	4
2-2	AA60-10050R	SCREW-ASSY;WC,HH,+M5,L31.5,SWR	4	CRT+CF
2-3	3704-000103	SOCKET-CRT;10P,22.5PI,14.3PI,S	1	V999
3	AA64-00055B	CABINET-BACK;-,TT14A5,-,HIPS,HB,BLK,-	1
3-1	6002-000514	SCREW-TAPPING;RH,+,2,M4,L15,ZP	6	CB+CF
3-2	L9400-0002	ANT-RODVHF;4SDODIPOLE500MMBRN	1
4	AA61-20070A	POWERCORDEP2N/P;L3000-0001,2.1	1
А	AA94-10149X	ASSY-PCB,MAIN(OPT);V15A,14,S/V,MEXICO	1
A-1	AA60-10008A	SCREW-TAPPING;-,TH,+,M3,L10,ZP	7	PCB+HC
A-2	AA61-20231A	HOLDER-CHASSIS;DP,-,-,-,AA61-2	1
A-3	AA63-00075A	SHIELD-CASE;SECC,T0.6,TS-DECK,ALL,V15A.	1
A-4	6002-000510	SCREW-TAPPING;RH,+,2,M3,L8,ZPC	2	SC+HC
В	AA90-40008B	ASSY-FRAME;SAMEX,CKD,TVN502V	1
B-1	LA63-00006A	ASSY-COVER/FRAME,TOP;CVR/FR+SHIELD-PLATE	1
B-2	6002-000507	SCREW-TAPPING;RH,+,2,M3,L12,ZP	3	CFT+FD
B-3	6002-000522	SCREW-TAPPING;TH,+,2,M4,L15,ZP	3	DE+FD
B-4	AA91-40124A	ASSY-DECK;-,4HD,NTSC,X-9,DLCMEXICO	1
B-5	AA94-80004K	ASSY-M/DECK;M-420N/SER.31,4HD,NTSC,-,TS	1
B-6	AA63-40313A	SHIELD-BOTTOM;-,SPTE,T0.5,-,TVN334V	1
B-7	6002-000507	SCREW-TAPPING;RH,+,2,M3,L12,ZP	2	FD+PCB
B-8	AA64-00024R	DOOR-HOUSING;4HD,ABS,HB,BLK,20A54(LATIN)	1
B-9	AA61-00050A	SPRING-DOOR;-,SUS304,0.5,OD6,H9.7,N8,-,T	1

Page 35

7-2 TT20A54X

No	Code No.	Description; Specification	Q'ty	Remark
1	AA92-00002L	ASSY-CABINET,FRONT;TT20A5,MEX,V15A,19	1
1-1	AA64-70010D	BADGE-BRAND;-,AL,-,L50,GOLD,R2	1
1-2	3001-001037	SPEAKER;5W,80HM,89DB,180HZ	1
1-3	6003-000333	SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW	4	SPK+CF
1-4	LA95-40005S	ASSY-PCB,A/V;-,KCV13A,V15A,13,19
1-5	6003-000333	SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW	2	AV+CF
1-6	AA64-00018A	WINDOW-REMOCON;-,TT13/19A52,-,PC,VIOLET.	1
1-7	AA64-00012A	INDICATOR-LED;-,TT13/19A52,-,PC,-,CLEAR.	1
1-8	AA64-00012A	INDICATOR-LED;-,TT13/19A52,-,PC,-,CLEAR.	1
1-9	AA64-00011D	KNOB-FAMILY;-,TT14/20A5,PA100,ABS,HB,BLK	1
1-10	6002-000512	SCREW-TAPPING;RH,+,2,M4,L12,ZP	2	KF+ CF
2	AA03-10029W	CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT.	1
2-1	L9400-0001	HOLDER-DEGAUSSING;25POLYVINYLCHLORIDEFL	4
2-2	AA60-10050R	SCREW-ASSY;WC,HH,+M5,L31.5,SWR	4	CRT+CF
2-3	3704-001105	SOCKET-CRT;11P,20PI,26.5PI,NI,-	1	V999
3	AA64-00056B	CABINET-BACK;-,TT20A5,-,HIPS,HB,BLK,-	1
3-1	6002-000514	SCREW-TAPPING;RH,+,2,M4,L15,ZP	6	CB+CF
3-2	L7000-0130	ANT-RODVHF;4SDODIPOLE500MMBRN	1
4	L3000-0001	POWER-CORD,AC;DW-006/MSP-10/,SPC-2/2100	1
А	AA94-10149W	ASSY-PCB,MAIN(OPT);V15A,19,S/V,MEXICO	1
A-1	AA60-10008A	SCREW-TAPPING;-,TH,+,M3,L10,ZP	6	PCB+HC
A-2	AA61-20232A	HOLDER-CHASSIS;DP,-,-,-,AA61-2	1
A-3	AA63-00075A	SHIELD-CASE;SECC,T0.6,TS-DECK,ALL,V15A.	1
A-4	6002-000510	SCREW-TAPPING;RH,+,2,M3,L8,ZPC	2	SC+HC
В	AA90-40008B	ASSY-FRAME;SAMEX,CKD,TVN502V	1
B-1	LA63-00006A	ASSY-COVER/FRAME,TOP;CVR/FR+SHIELD-PLATE	1
B-2	6002-000507	SCREW-TAPPING;RH,+,2,M3,L12,ZP	3	CFT+FD
B-3	6002-000522	SCREW-TAPPING;TH,+,2,M4,L15,ZP	3	DE+FD
B-4	AA91-40124A	ASSY-DECK;-,4HD,NTSC,X-9,DLCMEXICO	1
B-5	AA94-80004K	ASSY-M/DECK;M-420N/SER.31,4HD,NTSC,-,TS	1
B-6	AA63-40313A	SHIELD-BOTTOM;-,SPTE,T0.5,-,TVN334V	1
B-7	6002-000507	SCREW-TAPPING;RH,+,2,M3,L12,ZP	2	FD+PCB
B-8	AA64-00024R	DOOR-HOUSING;4HD,ABS,HB,BLK,20A54(LATIN)	1
B-9	AA61-00050A	SPRING-DOOR;-,SUS304,0.5,OD6,H9.7,N8,-,T	1

Page 36

	Loc. No	Parts No.	Description ; Specification	Remark
	B410	AC31-12016A	MOTOR-LOADING ASSY;-,-,X-9
	B440	AC60-10515A	SCREW-MACHINE;-,PH,+,-,M3,L3,ZPC,-,YEL
	B444	AC66-20571A	GEAR-WORM;-,POM SW-01,0.5,2,-,4.5,X-9
	B446	AC61-21005A	HOLDER-WORM;-,POM M90-44,-,-,-,X-9
	B448	AC66-20573A	GEAR-WORM WHEEL;-,POM SW-01,0.6,11,-,6.6
	B452	AC66-20575A	GEAR-FL CAM;-,POM SW-01,M0.6,Z88,-,PCD58
S.N.A.	B473	AC61-60559A	SPRING-PINCH DRIVE;-,TS,SUS304,PI0.5,OD4
	G001	AC96-10481K	ASSY-CYLINDER;CX-9, NTSC 6HD	(6HD NON-DIAMOND HEAD)
		AC96-10481H	ASSY-CYLINDER;CX-9, NTSC 4HD	(4HD NON-DIAMOND HEAD)
		AC96-10481F	ASSY-CYLINDER;CX-9, NTSC 2HD	(2HD NON-DIAMOND HEAD)
	G420	AC66-80142A	SLIDER-SUPPLY ASSY;-,X-9(TS),-,-,-,X-9
	G450	AC66-80141A	SLIDER-TAKE UP ASSY;-,X-9(TS),-,-,X-9
	G480	AC33-10217H	HEAD-ACE ASSY;-,-,-,X-9
	G510	AC60-10518A	SCREW-TAP TITE;-,PH,+,SW+ZW,M2.6,L5.6,ZP
	^-6680 G520	AC66-30539A	LEVER-#9 GUIDE ASSY;-,X-9(TS),-,-,-,X-9
	^G555 G527	AC61-60553A	SPRING-#9 GUIDE;-,ES,SUS304-WPB,OD3.1,0.
	S530	AC33-10217G	HEAD-FE;VAA00000275,-,-,-,X-9
	K546 S.N.A. G532	AC60-10519A	SCREW-TAP TITE;-,PH,+,-,M2.6,L8,ZPC
	G546	AC66-30535A	LEVER-FL DOOR;-,POM M90-44,-,-,BLK,X-9
	G555	AC59-90403A	UNIT-PINCH ASSY;X-9,-
	G680	AC66-30557A	LEVER-H/CLEANER ASSY;-,POM+URETHANE,-,-	(OPTIONAL)
	K110	AC66-10267A	REEL-DISK S;-,POM M90-44,-,-,X-9
	К140	AC66-10268A	REEL-DISK T;-,POM M90-44,-,-,X-9
	к182	AC66-30524A	LEVER-IDLER;-,POM9044,-,-,-,-
	Е́ К188	AC66-20577A	GEAR-IDLER;-,PEBAX 7033,-,-,-,X-9
	К240	AC66-30538A	LEVER-TENSION ASSY;-,X-9(TS),-,-,X-9
K340 K340	К248	AC61-60554A	SPRING-TENSION LEVER;-,ES,SUS304-WPB,OD3
B444	빈 K250	AC63-12029A	BAND-BRAKE ASSY;-,X-9(TS),-,-,X-9
	K330	AC66-30550A	LEVER-S.BRAKE ASSY;-,POM+SUS,-,-,-,X-9
	452 K340	AC66-30549A	LEVER-T.BRAKE ASSY;-,POM+SUS,-,-,X-9
	K350	AC61-60564A	SPRING-BRAKE;-,TENSION,SWP-A,0.25,3,-,X-
G546 SL	N.A. K490	AC61-21010A	HOLDER-CASS ASSY;-,SECC+POM+SUS,-,-,-,X-
	K502	AC61-60561A	SPRING-FL.LEVER-LR;-,ES,SUS304 WPB,PI2.7
• SNA •	: Service Not Available K530	AC66-30546A	LEVER-FL.ARM ASS'Y;-,SECC+POM+SUS,-,-,-,
	K546	AC61-50658A	GUIDE-CASS. DOOR;-,POM M90-44,-,-,NTR,-,

Page 37

7-4 Mechanical Parts (Bottom Side)


Loc. No	Parts No.	Description ; Specification	Remark
B238	AC61-50660A	SLEEVE-TENSION;-,POM M90-44,-,-,ID3,-,-,
B456	AC66-20576A	GEAR-JOINT 1;-,POM SW-01,M1.0,Z22,-,PCD2
B458	AC66-20574A	GEAR-JOINT 2;-,POM SW-01,M1.0,Z14,-,PCD1
B462	AC60-10517A	SCREW-TAP TITE;-,PH,+,-,M2.6,L5,ZPC,-,YE
B484	AC66-20580A	GEAR-LOADING DRIVE;-,POM SW-01,M1.0,Z32,
B488	AC66-30543A	LEVER-S LOAD ASSY;-,-,-,-,X-9
B500	AC66-30542A	LEVER-T LOAD ASSY;-,-,-,X-9
B560	AC31-12017A	MOTOR-CAPSTAN;DMVCMC07C,-,X-9
B570	AC60-10514A	SCREW-CAPSTAN;-,PH,+,M2.6,L6,-
G542	AC66-60051A	BELT-PULLEY;-,5CM-70,2 * 2,-,71.3,-,X-9
K200	AC61-21012A	HOLDER-CLUTCH ASSY;-,-,-,X-9
K221	AC66-20581A	GEAR-CENTER ASSY;-,POM,M=0.5,-,HIGHT T.,
K222	AC60-30306A	WASHER-SLIT;-,-,ID2.1,OD5.0,T0.5,-,POLYS
K225	AC66-30547A	LEVER-UP DOWN ASSY;-,POM+SUS,-,-,-,X-9

Page 38

8. Electric Parts List

8-1 TT14A54X/XAX (TT20A54X/XAX and TT14A54X/XAX Dissimilar Parts)

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification	Remark
		ASSY-PCB,MAIN(OPT)				ASSY-CABINET,FRON	Т
	* AA94-10	)149XASSY-PCB,MAIN(OPT);V15A,14,S/V,MEXIC	0		* AA92-0	0002MASSY-CABINET,FRONT;TT14A5,MEX,V1	5A,14
C402	2306-0003	326 C-FILM,MPPF;4.7nF,5%,1.6KV,TP,28.5x16x9n	۱	B/C	AA64-000	055B CABINET-BACK;-,TT14A5,-,HIPS,HB,BLK,-
HCOCHA	AA61-202	31A HOLDER-CHASSIS;DP,-,-,-,AA61-		BADGE	AA64-700	009DBADGE-BRAND;-,AL,-,L40,GOLD,R
R257	2008-0002	e66 R-FUSIBLE(S);10HM,5%,2W,AF,TP		BOSS	L3113-00	03-000BOSS-CABINET;HIPSHBBLK
R304	2001-0011	20 R-CARBON(S);3.30HM,5%,1/2W,AA		CDCOIL	L9400-00	02HOLDER-DEGAUSSING;20POLYVINI
R407	2003-0006	44 R-METAL OXIDE(S);300ohm,5%,2W,AA,TP,4	(12	CP	AA64-200	060DCONTROL-PANEL;HIPS,HB,BLK,PA100,TT1	14A5
R411	2004-0013	89 R-METAL(S);196KOHM,1%,1/2W,AA		D-COIL	AA27-200	04C COIL-DEGAUSSING;-,14,4.5ohm,30T,L890	,D
R510	2001-0005	68 R-CARBON;270HM,5%,1/8W,AA,TP,		F/C	AA64-001	23ALASSY-FRONT; HIPS, HB, BLK, PA100, TT14A	5
R511	2001-0005	68 R-CARBON;270HM,5%,1/8W,AA,TP,		F/C	AA64-001	23B CABINET-FRONT; HIPS, HB, BLK, PA100, TT1	4A5
R512	2001-0005	68 R-CARBON;270HM,5%,1/8W,AA,TP,
R513	2001-0000	05 R-CARBON;3900HM,5%,1/8W,AA,TP

ASSY-SPEAKER

	AA96-40056AASSY-SPEAKER;-,80HIVI,2VV,77BR02IV,-,L200
,


_/SPK	AA39-20500ALEAD CONNECTOR-ASSY:-,67096-003,REC,3(2

ASSY-CRT

2001-000005 R-CARBON;3900Hin;5%,1/8W,AA,TP 2001-000005 R-CARBON;3900HM,5%,1/8W,AA,TP 2004-001987 R-METAL:4.3K0HM.1%,1/2W.AA,TP

AA26-00004A TRANS-FLYBACK;-,FSA38026S,13 3704-000103 SOCKET-CRT-10P 22 5PL14 3PL

RX03 T444

* AA97-50001CASSY-CRT;A34KQV42X,-,14INCH,ITC,-,MINI(

C-Y	AA27-00001A MAGNET-CONVERGENCE; JH225-06A, 225MM
C RT	AA03-10001DCRT-COLOR;-,A34KQV42X,+380MG,14,90DEG,5
D-Y	L7000-0005 DEFL-YOKE(SEMSA);DSE-1422FL

8-2 TT20A54X/GSU (TT20A54X/XAX and TT20A54X/GSU Dissimilar Parts)

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification	Remark
		ASSY-PCB,MAIN(OPT)				ASSY-CRT
	* AA94-10	149QASSY-PCB,MAIN(OPT);V15A,19,F/V,TS-DEC	K		* AA94-50	0014KASSY-CRT;A48KRD82X(HB),0MG,20\|
RP801 C804 C801 PWR/AC	1404-0010 2401-0022 1203-0014 AA96-2005	48 POSISTOR;70HM,3P 19 C-AL:220UF,20%,400V,-,25X40,10MM,ST 94 IC-PEM CONTROLLER:3S0680RF,T03PF-5L,5, 1G ASSY-POWFR CORD:- CP2/NO(4.0).H/C250.K	21 KP	CRT C-Y	AA03-100 AA27-000	30L CRT-COLOR;A48KRD82X(HB),0MG,BI0,S-TIN 02AMAGNET-CONVERGENCE:JH291-SC-0B,29.	T 1M
1110710	1000 2000					ASSY-ACCESSORY
		ASSY-CABINET, FRONT		PLUG	3721-0001	136 PLUG-CONVERSION;15A300VPI4.0C\|
	* AA92-00	002IASSY-CABINET,FRONT;TT20A5,LATIN,V15A,	19
D-COIL CDCO/L	AA27-2000 L9400-000	03X DEGAUSSING-COIL;20,14.40HM,4\|T 2 HOLDER-DEGAUSSING;20POLYVINI\|

Page 39

8-3 TT20A54X/RCL (TT20A54X/XAX and TT20A54X/RCL Dissimilar Parts)

8-3 TT20A54X/XAX

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification
				C234	2301-000232
		ASSY-PCB, MAIN(UPT)		C234	2301-000232	C-FILM PEF-10nE 5% 50V TP 6x7x3 2mm 5mm
				0238	2202-002037	C-CERAMIC MIC-AXIAI 100NE+80-20
	* AA94-10	49WASSY-PCB, MAIN(OPT); V15A, 19, S/V, MEXIC	00	C239	2202-002037	C-CERAMIC MIC-AXIAL 100NF+80-20
				C240	2401-001363	C-AL:470UE20% 16V GPTP 10X12
C101	2202-00012	27 C-CERAMIC,MLC-AXIAL;10NF,+80-2		C241	2401-001363	C-AL:470UE20% 16V GPTP10X12
C102	2401-00066	0 C-ELECTROLYTIC;CE04WTAPG50V2.2		C301	2301-000016	C-FIL MPFF:22NF.5%.100V.TP.7.2X
C104	2202-00012	27 C-CERAMIC,MLC-AXIAL;10NF,+80-2		C302	2201-000556	C-CERAMIC.DISC:470PE.10%.500V
C108	2401-00048	80 C-AL;10UF,20%,50V,GP,5X11MM,5M		C303	2201-000982	C-CERAMIC.DISC:10NE.+80-20%.50
C109	2401-00310	02 C-AL;100uF,20%,10V,GP,TP,5x11,5		C304	2401-000553	C-AL:1UE.10%.50V.GP.5X11MM.5MM
C150	2401-00048	80 C-AL;10UF,20%,50V,GP,5X11MM,5M		C305	2305-000427	C-FILM.MPFF:47NE.5%.100V.7.5X1
C151	2202-00012	27 C-CERAMIC,MLC-AXIAL;10NF,+80-2		C306	2401-000173	C-AL:1000uE20%.35V.GP.TP.13x25.5
C152	2401-00048	80 C-AL;10UF,20%,50V,GP,5X11MM,5M		C308	2301-000310	C-FILM.PEF:68NF.5%.50V.8.0X8.5
C153	2202-00012	27 C-CERAMIC,MLC-AXIAL;10NF,+80-2		C309	2401-000360	C-AL;100UF,20%,50V,GP,8X11MM,5
C201	2202-00079	6 C-CERAMIC,MLC-AXIAL;1NF,10%,50		C310	2401-000493	C-AL:10UF.20%.50V.WT.5X11MM.5M
C202	2401-00133	33 C-ELECTROLYTIC;CE04WTAPG50V0.4		C311	2401-001333	C-ELECTROLYTIC;CE04WTAPG50V0.4
C203	2401-00261	9 C-AL;47uF,20%,25V,GP,TP,5x11,5		C312	2401-000553	C-AL;1UF,10%,50V,GP,5X11MM,5MM
C204	2401-00048	80 C-AL;10UF,20%,50V,GP,5X11MM,5M		C313	2305-000470	C-FILM,MPEF;68NF,5%,100V,-,5MM
C205	2401-00133	33 C-ELECTROLYTIC;CE04WTAPG50V0.4		C401	2301-000016	C-FILMPEF;22NF,5%,100V,TP,7.2X
C206	2202-00080	07 C-CERAMIC,MLC-AXIAL;22nF,+80-20%,25V,	Y5V	C402	2306-000330	C-FILM;CF922P1.6KVT772-HBUP
C207	2401-00133	33 C-ELECTROLYTIC;CE04WTAPG50V0.4		C404	2306-000193	C-FILM,MPPF;360NF,5%,200V,-,7.
C208	2401-00048	80 C-AL;10UF,20%,50V,GP,5X11MM,5M		C405	2305-000704	C-M,POLYESTER;CFS922MTAPG250V1
C209	2202-00203	37 C-CERAMIC,MLC-AXIAL;100NF,+80-20		C406	2201-000556	C-CERAMIC,DISC;470PF,10%,500V,
C210	2202-00203	37 C-CERAMIC,MLC-AXIAL;100NF,+80-20		C407	2401-001415	C-AL;470UF,20%,35V,GP,TP,10X20MM,5M
C211	2202-00203	37 C-CERAMIC,MLC-AXIAL;100NF,+80-20		C408	2201-000556	C-CERAMIC,DISC;470PF,10%,500V,
C212	2202-00012	27 C-CERAMIC,MLC-AXIAL;10NF,+80-2		C409	2401-000832	2 C-AL;220UF,20%,25V,GP,8X11MM,5
C213	2201-00019	73 C-CERAMIC, DISC; 10PF, 0.25PF, 50V		C410	2401-002619	C-AL;47uF,20%,25V,GP,TP,5x11,5
C214	2401-00066	60 C-ELECTROLYTIC;CE04WTAPG50V2.2		C411	2201-000556	C-CERAMIC,DISC;470PF,10%,500V,
C215	2401-0026	19 C-AL;4/uF,20%,25V,GP,1P,5x11,5		C412	2401-003114	C-AL;4.7UF,20%,250V,WT,TP,10X1
0216	2202-00020	J5 C-CERAMIC, MLC-AXIAL;22PF,5%,50		C413	2401-000560	) C-AL;1UF,20%,160V,GP,GT,6.3,11MM
0217	2202-00079	6 C-CERAMIC, MLC-AXIAL; INF, 10%, 50		C444	2201-000441	C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
0218	2301-00039	75 C-FILIVI, PEF; 180F, 5%, 50V, 1P, 6.5X12.5X3.5MM	I	C445	2201-000441	C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
C219	2401-00162	25 C-AL;6.8UF,20%,50V,GP,5XTTMM,5		C501	2202-000231	C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3.
C220	2401-00060	J3 C-AL; TUF, 20%, 50V, GP, 5XTTIMIN, 51VIVI		C502	2202-000231	C-CERAMIC,MLC-AXIAL;330PF,10%,50V,Y5P,3.
0221	2401-00060			C503	2202-000263	C-CERAMIC,MLC-AXIAL;470PF,10%,50V,Y5P,3.
0222	2202-00203	37 C-CERAMIC, MILC-AXIAL; 100NF,+80-20		C505	2201-002063	C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,1
0224	2401-00048	30 C-AL;10UF,20%,50V,GP,5X11IVIIVI,5IVI		C601	2401-002619	C-AL;47uF,20%,25V,GP,TP,5x11,5
0225	2401-00048			C602	2301-000224	C-FILM,PEF;22NF,5%,50V,7.4X3.9
0220	2401-00000			C603	2401-000660	C-ELECTROLYTIC;CE04WTAPG50V2.2
0227	2202-00203			C604	2401-000480	C-AL;10UF,20%,50V,GP,5X11MM,5M
0229	2202-00012			C605	2401-001363	C-AL:470UF,20%,16V,GP,TP,10X12
0230	2300-00012			C609	2401-001397	C-AL;470UF,20%,25V,GP,10X16MM,
C232	2401-00214			C611	2202-000279	C-CERAMIC, MLC-AXIAL; 47PF, 5%, 50
6233	2401-00004	F/ G-LEEGIKULTIIG,GEU4WIAPG0UVZ.Z		C612	2202-000279	C-CERAMIC,MLC-AXIAL;47PF,5%,50

Page 40

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification	Remark
C801	2306-000318	3 C-FILM MPPF:220NF 20% 250V - 2		D815	0402-00013	2 DIODE-RECTIFIER-1N4004 400V 1A DO-41
C803	2201-000987	7 C-CERAMIC.AC:CK45PE400V222-M(T		D817	0402-000132	2 DIODE-RECTIFIER:1N4004,400V,1A,DO-41
C804	2401-003024	4 C-AL;220UF,20%,200V,WT,TP,22X35.1MM		D901	0403-000355	5 DIODEZENER;UZ5.1BSB,4.97~5.17V,0.5UA,500
C805	2303-000163	3 C-FILM,PPF;2.2NF,5%,800V,-,-,T		D903	0401-00000	5 DIODE;1N4148TAPG
C806	2301-000310	) C-FILM,PEF;68NF,5%,50V,8.0X8.5		D904	0401-00000	5 DIODE;1N4148TAPG
C807	2305-000665	5 C-FILM;CF922N63VT104-J-40/1053		DX01	0403-00029	7 DIODE-ZENER;EQA02-06D/MTZ6.2B(
C808	2401-0015/1	C-ELECTROLYTIC;CE04WTAPG50V4/-		DX02	0402-000132	2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41
C809	2301-000016			DZ801	1405-001030
C812	2201-000987			DZ802	0403-000300	5 DIODE-ZEINER, IVITZ6.20, 7.76-199, 5 DIODE-ZENER:FOA02-064/MITZ5.68(
C813	2201-000599	C-CERAMIC DISC:560PE10% 500V		DZ803	1405-00103	5 VARISTOR:430V 2500A 14x8 5mm TP
C814	2401-000262	2 C-AL;100UF,20%,160V,GP,16X25MM,5MM,		DZ805	0403-00055	1 DIODE-ZENER;MTZ3.9B,3.9V,3.89-4.16V,500M
C815	2401-001486	5 C-AL;47UF,20%,160V,HR,13X20MM,5MM,T		F801	3601-001012	2 FUSE-FERRULE;250V,4A,SLOW-BLOW
C816	2401-002215	5 C-AL;2200UF,20%,25V,(105RD)13X		F801A	3602-000114	4 FUSE-HOLDER;-,-,30MOHM
C817	2401-001998	3 C-AL;1000UF,20%,25V,GP,TP,10X20		F801B	3602-000114	4 FUSE-HOLDER;-,-,30MOHM	_
C818	2301-000192			GITOT	AA39-20010	BLEAD-CONNECTOR, ASSY;-, YFH800-01, 500MM, 1	Р
0819	2201-000374				AA01-20232
C820	2201-000550	5 C-ELEC:CE04D16VT471-MER10X12 5			1204-001259
C822	2401-001363	3 C-AL:470UF.20%.16V.GP.TP.10X12		1C202	1001-00021	5 IC-RF/V1/AUDIOS/W:KA8404.SPDTC
C823	2401-001363	3 C-AL;470UF,20%,16V,GP,TP,10X12		A IC301	1204-00047	5 IC;KA2131	H/SINK
C824	2401-000480	) C-AL;10UF,20%,50V,GP,5X11MM,5M		\land IC601	1201-001200	) IC-POWERAMP;7267,DIP,8P,346MIL
C825	2305-000665	5 C-FILM;CF922N63VT104-J-40/1053		A IC801	1203-001493	3 IC-PEM CONTROLLER;3S0765RF,TO3PF-5L,5,21	H/SINK
C826	2401-000302	2 C-AL;100UF,20%,25V,GP,6X11MM,5		A IC802	1203-000284	4 IC-POSI.FIXEDREG.;7806,TO-220,	H/SINK
C827	2305-000665	5 C-FILM;CF922N63VT104-J-40/1053			AA13-00021	AIC-MCU;-,Z9036512PSC-R4133,16BIT,SDIP
C901	2306-000122			Z!\ IC902	1202.00000
C902	2202-000790			ZIX 10903	2701-00011
C906	2201-000483	3 C-CERAMIC DISC:33PE5% 50V NPO		1151	2701-000115	3 INDUCTOR-AXIAL 22UH 10% 2.5X3
C907	2401-000962	2 C-AL;22uF,20%,50V,GP,TP,5x11,5		L152	2701-000320	5 INDUCTOR AXIAL;560NH,10%,2.3X3.4MM
C908	2201-000961	C-CERAMIC,DISC;10pF,0.5pF,50V,RH,TP,5x3m		L201	AA26-10004	K TRANS-IF;-,7MG,SIF,-,7MM,100PF
C909	2401-002594	4 C-AL;220uF,20%,16V,GP,TP,8x11.5,5		L202	2701-00020	7 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
C910	2201-000257	7 C-CERAMIC,DISC;16PF,5%,50V,NPO		L203	2701-000158	B INDUCTOR-AXIAL;22UH,10%,2.5X3.
C912	2301-000310	) C-FILM,PEF;68NF,5%,50V,8.0X8.5		L204	2/01-00020	/ INDUCTOR-AXIAL;560H,5%,2.5X3.4
C913	2202-000164			L205	AA26-10004
C914 C915	2201-000480	7 C-AL, 100F,2076,307,9F,3XT ΠΥΙΝΙΑ,3ΝΙ 7 C-CERAMIC MI C-ΔΧΙΔΙ 100NF ±80-20		L200	2701-00011	7 CORE-FERRITEREΔD:ΔΔ 3 5X1 0X6
C916	2202-000210	C-CERAMIC,MLC-AXIAL:270pF.10%.50V.Y5P.TP		L301	2701-000110	5 INDUCTOR-AXIAL:10UH.10%.4.2X9.
CN201	3711-003641	CONNECTOR-HEADER;BOX,12P,1R,2.		L401	AA27-30001	B COIL-LINEARITY;-, 195UH, QIC1010
CN501	AA39-20620	ALEADCONNECTOR-ASSY;-,YBNH025-09,S,9P,30		L402	2701-001032	2 INDUCTOR-AXIAL;100UH,10%,5X14MM
CN601	3711-002642	2 POST-HEADER;67094-003(AUTO)		L403	2901-00029	7 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-
CN602	3711-002645	5 POST-HEADER;67094-006(AUTO)		L602	2701-000158	3 INDUCTOR-AXIAL;22UH,10%,2.5X3.
CN902	3/11-003641	CLAND WIDE, NVLON 44, V2 DLK, W2 ZE		L801	AA29-30001	R FILTER-LINE;-,6MH,2.0A,-,SQ191
CVVIRES CV01	2202.000127			L0U2	3301-00122
CX02	2401-000480	C-AL:10UE 20% 50V GP5X11MM 5M		1804	3301-00028	7 CORE-FERRITEBEAD: AA 3 5X1 0X6
CX03	2401-000480	C-AL;10UF,20%,50V,GP,5X11MM,5M		L806	2701-001032	2 INDUCTOR-AXIAL;100UH,10%,5X14MM
D101	0403-000700	DIODE-ZENER;TZP33A,33V,31-35V,		L807	2701-000114	INDUCTOR-AXIAL;10UH,10%,2.5X3.
D102	0403-000296	5 DIODE-ZENER;EQA02-06A/MTZ5.6B(		L808	3301-00028	7 CORE-FERRITEBEAD;AA,3.5X1.0X6.
D201	0403-000663	3 DIODE-ZENER;MTZ3.3B,3.3V,3.32-		L809	2901-00029	7 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-
D202	0401-000005	DIODE;1N41481APG		L810	2701-00020
D203	0401-00000			LOTT 1.812	2901-00029
D204	0403-000296	5 DIODE, TRATAGORIO		1901	2701-000122	1 INDUCTOR-AXIAL 100UH 10% 2.5X3
D206	0401-000005	5 DIODE;1N4148TAPG		NT801	1404-00018	7 THERMISTOR;KL11L4R7-3.5A4.70HM
D207	0401-000005	5 DIODE;1N4148TAPG		PC802	0604-001038	9 PHOTOCOUPLER;TR,130-260%,200MW
D208	0401-000005	5 DIODE;1N4148TAPG		PCB+HC	AA60-10008	ASCREW-TAPPING;-,TH,+,M3,L10,ZP
D301	0402-001105	5 DIODE-RECTIFIER;ERB43-04SV1,40		POWER/C	L3000-0001	POWER-CORD, AC; DW-006/MSP-10/, SPC-2/2100	)
D401	0401-000005	5 DIODE;1N4148TAPG		PWR/AC	L3000-0005	POWERCORDEP2N/P;L3000-0001,2.1
D402	0402-000132			0151	0501-000430	5 TR-SMALLSIGNAL;KTC3197,NPN,30V
D403	0402-00110:	5 DIODE-RECTIFIER,ERD43-043V1,40		0201	0501-00038	7 TRANSISTOR, KSC013-1(TAPG)/TTAM 2 TRANSISTOR: KSC015-1(TAPG)/YTAM
D404	0402-001105	5 DIODE-RECTIFIER/ERB43-045V1 40		0202	0501-00038	TRANSISTOR, KSC015-1(TAPG)/TTAM
D407	0402-001105	5 DIODE-RECTIFIER;ERB43-04SV1,40		0204	0501-000389	7 TRANSISTOR;KSC815-Y(TAPG)/YTAM
D601	0403-000563	B DIODE-ZENER;MTZ9.1B,9.1V,8.57-		⚠ Q401	0502-00111	5 TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8
D801	0402-000213	B DIODE-RECTIFIER;ERB12-06,600V,		∧ Q402	0501-000369	9 TRANSISTOR;KSC2331-Y(TAPG)
D802	0402-000213	3 DIODE-RECTIFIER;ERB12-06,600V,		Q501	0501-00201	4 TR-SMALLSIGNAL;KSC2330-RNPN
D803	0402-000213	B DIODE-RECTIFIER;ERB12-06,600V,		Q502	0501-00201	A TR SMALLSIGNAL;KSC2330-RNPN
	0402-000213			U5U3	1202 00121
0005	0402-001105	5 DIODE-RECTIFIER,ERD43-045V1,40 5 DIODE-RECTIFIER:FRR#3-045V1.40		10001	0504-00121	7 TC-FUST,ADJUSTREG,431,10-92,38,4.381VIIL,P 3 TR-DIGITAL-KSR1003 NPN 300M/M/ 2
D807	0402-000540	DIODE-RECTIFIER:RU20A.600V15		▲ 0804	0501-00031	5 TR-SMALLSIGNAL:KSA928A-YPNP1
D808	0402-001105	5 DIODE-RECTIFIER;ERB43-04SV1,40		▲ 0805	0501-000369	9 TRANSISTOR;KSC2331-Y(TAPG)
D809	0404-001056	DIODE-SCHOTTKY;RK16,60V,1.5A,DO-204AC,TP		Q902	0501-00038	7 TRANSISTOR;KSC815-Y(TAPG)/YTAM
D810	0402-000132	2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41		QX01	0501-00028	3 TRANSISTOR;KSA539-Y(TAPG)/YTAM
D813	0402-000132	2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41		R101	2004-00102	7 R-METAL;5.6KOHM,5%,1/8W,AA,TP,
D814	0404-001056	» DIUDE-SCHUTTKY;RK16,60V,1.5A,DO-204AC,TP	,	R102	2001-001000	j k-ivietal;82konm,5%,1/8W,AA,1P,1.8x3.2mm

Page 41

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification	Remark

R103	2001-000429	R-CARBON:1Kohm.5%.1/8W.AA.TP.1.8x3.2mm		R415	2003-000784	R-METAL OXIDE(S):7.5KOHM.5%.2W.AF.TP.3.7
R104	2003-001037	R-METAL(OXIDE): 390HM.5%, 2W.AF.		R416	2001-000022	R-CARBON(S):330HM.5%.1/2W.AA.T
R152	2001-000221	R-CARBON:1.2KOHM.5%.1/8W.AA.TP		R444	2001-000109	R-CARBON(S):4700HM.5%.1/2W.AA.
R153	2001-000734	R-CARBON: 4.7KOHM.5%, 1/8W.AA.TP		R501	2001-000007	R-CARBON:3KOHM.5%,1/8W.AA,TP.1
R154	2001-000780	) R-CARBON:470ohm.5%.1/8W.AA.TP.1.8x3.2mm		R502	2001-000007	R-CARBON:3KOHM.5%,1/8W.AA,TP.1
R155	2001-000281	R-CARBON 1000HM 5% 1/8W AA TP		R503	2001-000007	R-CARBON-3KOHM 5% 1/8W AA TP1
R156	2001-000793	8 R-CARBON:470HM.5%.1/8W.AA.TP.1		R504	2003-000784	R-METAL OXIDE(S):7.5K0HM.5%.2W.AE.TP.3.7
R158	2001-000007	R-CARBON 3KOHM 5% 1/8W AA TP1		R504A	2003-000784	R-METAL OXIDE(S):7 5KOHM 5% 2W AFTP 3 7
R159	2001-000007	R-CARBON: 3KOHM 5% 1/8W AA TP1		R505	2003-000784	R-METAL OXIDE(S):7 5KOHM 5% 2W AFTP3 7
R201	2001-000290	R-CARBON 10KOHM 5% 1/8W AA TP		R505A	2003-000784	R-METAL OXIDE(S):7 5KOHM 5% 2W AFTP3 7
R202	2001-000734	R-CARBON 4 7KOHM 5% 1/8W AA TP		R506	2003-000784	R-METAL OXIDE(S):7 5KOHM 5% 2W AFTP3 7
R203	2001-000734	R-CARBON: 4.7KOHM.5%.1/8W.AA.TP		R506A	2003-000784	R-METAL OXIDE(S):7.5KOHM.5%,2W.AE.TP.3.7
R204	2001-000995	R-CARBON:8200HM.5%.1/8W.AA.TP.		R507	2001-000281	R-CARBON:1000HM.5%.1/8W.AA.TP.
R205	2001-000995	R-CARBON:8200HM.5%.1/8W.AA.TP.		R508	2001-000281	R-CARBON:1000HM,5%,1/8W,AA,TP
R206	2001-000995	R-CARBON;8200HM,5%,1/8W,AA,TP,		R509	2001-000281	R-CARBON;1000HM,5%,1/8W,AA,TP,
R207	2001-001111	R-CARBON(S);2400HM,5%,1/2W,AA,		R513	2001-000674	R-CARBON;3600HM,5%,1/8W,AA,TP,
R208	2001-000515	R-CARBON;2200HM,5%,1/8W,AA,TP,		R514	2001-000674	R-CARBON;3600HM,5%,1/8W,AA,TP,
R209	2001-000515	R-CARBON;2200HM,5%,1/8W,AA,TP,		R515	2002-001006	R-COMPOSITION;RC1/2T4.7KK/ERC-
R210	2001-000515	R-CARBON;2200HM,5%,1/8W,AA,TP,		R516	2001-000674	R-CARBON;3600HM,5%,1/8W,AA,TP,
R211	2001-000281	R-CARBON;1000HM,5%,1/8W,AA,TP,		R518	2008-001013	R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm
R212	2001-000281	R-CARBON;1000HM,5%,1/8W,AA,TP,		R602	2001-000995	R-CARBON;8200HM,5%,1/8W,AA,TP,
R213	2001-000837	R-CARBON;51KOHM,5%,1/8W,AA,TP,		R610	2001-000577	R-CARBON;2KOHM,5%,1/8W,AA,TP,1
R214	2001-001071	R-CARBON(S);12KOHM,5%,1/2W,AA,		R611	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
R215	2004-001402	R-METAL(S);6.8KOHM,1%,1/2W,AA,		R612	2001-000605	R-CARBON;3.6KOHM,5%,1/8W,AA,TP
R216	2001-000969	R-CARBON;750HM,5%,1/8W,AA,TP,1		R801	2002-001010	R-COMPOSITION;1.8MOHM,10%,1/2W,AA,TP,3
R217	2001-000702	R-CARBON;39KOHM,5%,1/8W,AA,TP,		R804	2003-000994	R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1
R218	2001-000472	2 R-CARBON;2.7KOHM,5%,1/8W,AA,TP		R805	2003-000994	R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1
R219	2001-000674	R-CARBON;3600HM,5%,1/8W,AA,TP,		R807	2001-001163	R-CARBON(S);5600HM,5%,1/2W,AA,
R221	2001-000515	5 R-CARBON;2200HM,5%,1/8W,AA,TP,		R808	2001-001178	R-CARBON(S);6800HM,5%,1/2W,AA,
R222	2001-000989	R-METAL;820Kohm,5%,1/8W,AA,TP,1.8x3.2m		R809	2001-000022	R-CARBON(S);330HM,5%,1/2W,AA,T
R223	2001-000780	) R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm		R810	2001-001134	R-CARBON(S);3600HM,5%,1/2W,AA,TP,2.4X6.4
R226	2001-000773	R-CARBON;470KOHM,5%,1/8W,AA,TP		R811	2002-001013	R-COMPOSITION;4.7MOHM,10%,1/2W,AA,TP,3	.7
R227	2001-000508	R-CARBON;220KOHM,5%,1/8W,AA,TP		R812	2001-0010/8	R-CARBON(S);15KOHM,5%,1/2W,AA,
R228	2001-000258	3 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m		R813	2001-001078	R-CARBON(S);15KOHM,5%,1/2W,AA,
R229	2001-000258	3 R-CARBUN, 1.8K000, 5%, 1/8W, AA, TP		R814	2001-001178	R-CARBUN(S);080UHIVI,5%,1/2W,AA,
KZ30	2001-000391			K815	2004-004089	K-IVIE IAL; IZ3KUHIVI, I %, I/ZVV, AA, IY, Z.3X0.3
RZ31 D222	2001-000241			D017	2001-001034	CARDON(S):1.0NUTIVI,3 %,1/2W,AD,TP,2.4A0.
P232	2001-000290			R820	2001-000019	P. METALOYIDE(S)-120HM 5% 200 A TP 42120	41.4
R235	2001-000270	R CARBON: 100KOHM 5% 1/8W/ 44 TP		R822	2003 000470	R_CARBON(S):300KOHM 5% 1/2W/ΔΔ	IIVI
R236	2001-000548	R-CARBON:270KOHM.5%.1/8W.AA.TP		R825	2001-001088	R-CARBON(S):1KOHM.5%.1/2W.AA.TP.2.4X6.4
R237	2001-000290	R-CARBON: 10KOHM, 5%, 1/8W, AA, TP,		R826	2001-000290	R-CARBON:10KOHM.5%,1/8W.AA.TP.
R238	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,		R827	2001-001134	R-CARBON(S);3600HM,5%,1/2W,AA,TP,2.4X6.4
R239	2001-000947	R-CARBON;7.5KOHM,5%,1/8W,AA,TP		R828	2001-000117	R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m
R240	2001-000577	R-CARBON;2KOHM,5%,1/8W,AA,TP,1		R829	2001-001134	R-CARBON(S);3600HM,5%,1/2W,AA,TP,2.4X6.4
R241	2001-000995	5 R-CARBON;8200HM,5%,1/8W,AA,TP,		R830	2001-001139	R-CARBON(S);39KOHM,5%,1/2W,AA,
R242	2001-000995	R-CARBON;8200HM,5%,1/8W,AA,TP,		R854	2004-001983	R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4
R244	2001-000734	R-CARBON;4.7KOHM,5%,1/8W,AA,TP		R901	2001-000890	R-CARBON;6.8KOHM,5%,1/8W,AA,TP
R246	2001-000780	) R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm		R902	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
R247	2001-000832	2 R-CARBON;5100HM,5%,1/8W,AA,TP,		R903	2001-000281	R-CARBON;1000HM,5%,1/8W,AA,TP,
R251	2001-000591	R-CARBON;3.3KOHM,5%,1/8W,AA,1P		R904	2001-001062	R-CARBON(S);10MOHM,5%,1/2W,AA,
R252	2001-000591	R-CARBON;3.3KOHM,5%,1/8W,AA,1P		R905	2001-000397	R-CARBON;180KOHM,5%,1/8W,AA,1P
R253	2001-000591	R-CARBUN;3.3KUHM;5%,1/8W;AA,1P		R906	2001-000290	R-CARBON; IUKOHM, 5%, 1/8W, AA, 1P,
K257	2008-001018			K907	2001-000290	R-CARBON, IUKUHIVI, 3%, I/8W, AA, IP,
R280 D201	2001-000241			R908	2001-000449
R301	2001-000003	2 R-CARDON, 3300HIM, 5%, 1/8W, AA, IF,		P010	2001-000734
R302	2001-000864	L R-CARBON/56Kohm 5% 1/8W/ ΔΔ TP1 8v3 2mm		R011	2001-000270	R_CARBON/170ohm 5% 1/8W/ΔΔ TP1 8v3 2mm
R304	2001-000004	R-CARBON(S)·2 70HM 5% 1/2W AA		R912	2001-000700	R-CARBON:4 3KOHM 5% 1/8W AA TP
R305	2001-000660	R-CARBON: 33KOHM 5% 1/8W/ AA TP		R913	2001-000723	R-CARBON'4 3KOHM 5% 1/8W AA TP
R306	2001-001000	R-METAL:82Kohm.5%.1/8W.AA.TP.1.8x3.2mm		R914	2001-000723	R-CARBON:4.3KOHM.5%.1/8W.AA.TP
R307	2001-000563	R-CARBON:27KOHM.5%.1/8W.AA.TP.		R915	2001-000869	R-CARBON:560HM.5%.1/8W.AA.TP.1
R308	2001-000633	R-CARBON: 30KOHM, 5%, 1/8W, AA, TP,		R916	2001-000281	R-CARBON:1000HM.5%.1/8W.AA.TP.
R309	2003-000537	R-METALOXIDE(S);1KOHM,5%,1W,AD		R917	2001-000281	R-CARBON;1000HM,5%,1/8W,AA,TP,
R401	2001-000780	R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm		R920	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,
R402	2001-000515	6 R-CARBON;2200HM,5%,1/8W,AA,TP,		R921	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
R403	2001-001114	R-CARBON(S);2700HM,5%,1/2W,AA,		R922	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
R404	2001-000117	R-CARBON(S);680hm,5%,1/2W,AA,TP,2.4x6.4m		R923	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
R405	2003-000540	) R-METALOXIDE(S);1KOHM,5%,2W,AD		R924	2001-000449	R-CARBON;2.2KOHM,5%,1/8W,AA,TP
R406	2003-002071	R-METALOXIDE;5600HM,5%,2W,AF,TP,3.9X10MN	Л	R925	2001-000449	R-CARBON;2.2KOHM,5%,1/8W,AA,TP
K4U/	2003-000455	K-IVIETALUXIDE(S); TUUUHM,5%,2W,AA, TP, N D METAL (S): 17(0):14,002, 17(0):44,4,7,70	1	K926	2001-000773
K4U8	2004-001390			K927	2001-000290
K4U9 D/10	2008-000253	K-FUSIBLE(S);U.47UHIVI,5%,1W,AF, DELISIBLE(S):10HM 5%,170M/AET		K928 2000	2001-000290
R/11	2000-000200			R03U	2004-001069	R-CARBON-2 4Kohm 5% 1/8/M/ AA TD1 8v2 2m
R412	2001-000020	) R-CARBON(S):220HM.5% 1/2W,AA T		R931	2001-000290	R-CARBON:10KOHM.5% 1/8W AA TP
R413	2001-001037	R-CARBON(S);0.390HM,5%,1/2W,AA		R932	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,

Page 42

Loc. No.	Code No.	Description ; Specification	Loc. No.	Code No.	Description ; Specification	F
R932A	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,			ASSY-M/DFCK
R933	2001-000281	R-CARBON;1000HM,5%,1/8W,AA,TP,
R934	2001-000449	R-CARBON;2.2KOHM,5%,1/8W,AA,TP		* ^ 0		NITCO TO
R935	2001-000472	R-CARBON;2.7KOHM,5%,1/8W,AA,TP		AA94-80	004KASSY-IVI/DECK;IVI-420IN/SEK.31,4HL	),INTSC,-,TS
R936	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,	A /CET	1 4 4 2 0000
RH01	2002-001006	R-COMPOSITION;RC1/2T4.7KK/ERC-	A/UFI	LA03-0000
RH02	2002-001006	R-COMPOSITION;RC1/2T4.7KK/ERC-	A/DEUK	AA91-4012		ICU
RLU01	3501-001040	RELAYPOWER;12VDC,500MW,10A,1FO	A/FRIVIE
RP801A	1404-000208	POSISTOR;PTH631D02BF7ROM140TDE	A/PUB-IVI/L	2201 0002		SC, W/KEY
RX01	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,	BDIVIOU2	3301-0002
RX02	2001-000411	R-CARBON;18KOHM,5%,1/8W,AA,TP,	DDIVI003	3301-0002
RX03	2004-001397	R-METAL(S);4.7KOHM,1%,1/2W,AA,	CFT+FD	0002-0000
RX04	2004-001376	R-METAL(S);11KOHM,1%,1/2W,AA,T	CIVITU2	2401-0020	19 C-AL;4/UF;20%;25V;GP;TP;5XTT;5
RX05	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,	CIVITU3	2401-0004	80 C-AL; 100F,20%,50V,GP,5X I 11VIIVI,51VI	`
RX08	2001-000837	R-CARBON;51KOHM,5%,1/8W,AA,TP,	CIVITUS	2202-0020	37 C-CERAIVIIC,IVILC-AXIAL; IUUNF,+80-20	J
SC	AA63-00075	ASHIELD-CASE;SECC,T0.6,TS-DECK,ALL,V15A.	CIVITUO	2401-0003	55 C-AL, TUF, TU76, 50V, GF, 5X T TIVIIVI, 51VIIVI
SC+HC	6002-000510	SCREW-TAPPING;RH,+,2,M3,L8,ZPC	CIVITU7	2401-0005
SF101	2904-000304	FILTER-SAW;M1859MNTSC/USAVIFST	CIVITIU	2401-0020	19 C-AL;470F,20%,25V,GP,TP,5XTT,5	`
T401	AA26-50001	BHORIZ.DRIVE;-,7.1MH,102UH,10-2	CIVITIT	2202-0020		J
∕! ∖ T444	AA26-30001	Y TRANS-FRYBACK;-,FSV-20A001,20,125V	CIVITIZ CM112	2401-0020	19 C-AL;4/UF,2U%,25V,GP,1P,5X11,5	`
∕!∖ T801	AA26-20007	UTRANS-SWITCHING;-,90~260V,125V/16.5V/9.5	CIVITIS CN4114	2202-0020		)
TU01	AA40-10005	TTUNER-F/S;TECC1070PG26A(S),NTS	CIVIT14	2401-0020	19 C-AL;4/UF,2U%,25V,GP,1P,5X11,5	`
∕!\ V999	3704-001105	SOCKET-CRT;11P,20PI,26.5PI,NI,-	CIVITIS	2202-0020	37 C-CERAIVIIC, IVILC-AXIAL; IUUNF, +80-20	J
X201	2801-000226	CRYSTAL-UNIT;3.579545MHZ,20PPM	CIVI2U9	2202-0008	30 C-CERAIVIIC, IVILC-AXIAL, 82PF, 10%, 5
X202	2802-000172	RESONATOR-CERAMIC;503.5KHZ,0.5	CIVIZII	2202-0008
X901	2801-003224	CRYSTAL-UNIT;32.768KHZ,20PPM,2	CIVIZ IZ	2301-0001	75 C-FILIVI, PEF; 151NF, 576, 50V, 7.1X3.5	111 AN A EN A
Z201	2903-001022	FILTER-CERAMIC;TR,4.5MHZ	CIVIZI3	2401-0000	30 C-ALUIVIINUIVI;22UF,20%,23V,GP,TP,5A
Z601	2903-000135	FILTER-CERAMIC;BP,4.5MHZ	CIVIZ 18	2401-0000	30 C-ALUIVIINUIVI;220F,20%,23V,GP,1P,5A
			CIVI3UT	2305-0006
			CIVI302	2401-0014	90 C-AL;47UF,20%,10V,GP,3X7IVIIVI,3IVIIVI	`
		ASSY-CABINET.FRONT	CIVI3U3	2202-0020
			CIVI3U4	2201-0004	YY U-UERAIVIIU, DISU; 3YUPF, 5%, 5UV, SL, 8.1	JA3.U,Z
	* ^ ^ 0.0 0000		CIVI3U5	2401-0012		14 0*0
	~AA92-0000.	ZLASST-UABINET,FRUNT;TTZUAS,IVIEX,VT5A,T9	CIVI3U/	2201-0003	45 U-UERAIVIIU, DISU; 2000F, 5%, 50V, SL, 1P	,0.3 3,
	A A 04 10007		CIVI3U8	2301-0001	10 U-FILIVI, PEF; 101VF, 070, 0UV, 7.1X3.5
A/ SPK			1.1/1509	2401-001.3

A/SPK	AA96-10007AASSY-SPEAKER;-,80HM,3W,05F14BRA,-,L300
AC+BC	AA65-30008ACLAMP-CORD;-,PE,HB,BLK,-,-
ACCERY	0203-000368 TAPE-OPPMASKING;#370,-,W50,L50,CLR
AV+CF	6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
B/C	AA64-00056B CABINET-BACK;-, TT20A5,-, HIPS, HB, BLK,-
BACK	AA63-60001L SPACER-FELT;-,FELT,T0.35,-,150X15,-
BADGE	AA64-70010D BADGE-BRAND;-,AL,-,L50,GOLD,R2
BXTAPE	L9200-0005 TAPE;TRANSPARENT,3X1000YDS,3M371,914mts
CB+CF	6002-000514 SCREW-TAPPING;RH,+,2,M4,L15,ZP
CB+FD	6002-000514 SCREW-TAPPING;RH,+,2,M4,L15,ZP
CDCOIL	L9400-0001 HOLDER-DEGAUSSING;25POLYVINYLCHLORIDEFL
CP	AA64-00049B CONTROL-PANEL; HIPS, HB, BLK, PA100, TT20A54
CRT+CF	AA60-10050R SCREW-ASSY;WC,HH,+M5,L31.5,SWR
CWIRE1	AA65-30018ACLAMP-WIRE;-,NYLON6.6,-,-,DATL
D-COIL	AA27-20004B COIL-DEGAUSSING;-,20,5.7ohm,30T,L2170,E
F/C	AA64-00025ALASSY-FRONT;HIPS,HB,BLK,PA100,TT20A5,LA
F/C	AA64-00025C CABINET-FRONT;HIPS,HB,BLK,TT20A5.
FBT	AA65-30109ACLAMP-FBT;NYLON-66,V2,BLK,-,-,-
IL	AA64-00012AINDICATOR-LED;-,TT13/19A52,-,PC,-,CLEAR.
IL + CF	6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
KF	AA64-00011DKNOB-FAMILY;-,TT14/20A5,PA100,ABS,HB,BLK
KF+ CF	6002-000512 SCREW-TAPPING;RH,+,2,M4,L12,ZP
L/SPK	AA39-20500GLEAD CONNECTOR-ASSY;-,67096-003,REC,3(2)
SPK	3001-000189 SPEAKER;3W,8OHM,85DB,180HZ
SPK+CF	6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW
STAPLE	AA60-40006APIN-STAPLE;-,-,-,H18,33X17.8X2
WR	AA64-00018A WINDOW-REMOCON;-,TT13/19A52,-,PC,VIOLET.

ASSY-CRT

* AA94-50019XASSY-CRT-A48KRD82X(H) +380MG 20 BARE -

	C-Y
Δ	CRT
	D-Y
	SPACER

AA27-60001DMAGNET-CONVERGENCE;-,JH-291-(J AA03-10029WCRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT. AA27-50004WD-Y-20 HI-TRON CRT AA27-50004WD-Y;20,HI-TRON CRT AA63-60028A SPACER-DY:-.NEOPRENE.-.BLK.VOW

A/DECK	AA91-40124A	ASSY-DECK;-,4HD,NTSC,X-9,DLCMEXICO
A/FRME	AA90-40008B	BASSY-FRAME;SAMEX,CKD,TVN502V
A/PCB-M/DE	CKAA96-80003	3HASSY-PCB,M/DECK;M-440N,4HD,NTSC,W/KE
BDM602	3301-000287	CORE-FERRITEBEAD;AA,3.5X1.0X6.
BDM603	3301-000287	CORE-FERRITEBEAD;AA,3.5X1.0X6.
CFT+FD	6002-000507	SCREW-TAPPING;RH,+,2,M3,L12,ZP
CM102	2401-002619	C-AL;47uF,20%,25V,GP,TP,5x11,5
CM103	2401-000480	C-AL;10UF,20%,50V,GP,5X11MM,5M
CM105	2202-002037	C-CERAMIC, MLC-AXIAL; 100NF,+80-20
CM106	2401-000553	C-AL;1UF,10%,50V,GP,5X11MM,5MM
CM107	2401-000553	C-AL;1UF,10%,50V,GP,5X11MM,5MM
CM110	2401-002619	C-AL;47uF,20%,25V,GP,TP,5x11,5
CM111	2202-002037	C-CERAMIC.MLC-AXIAL:100NF.+80-20
CM112	2401-002619	C-AL:47uF.20%.25V.GP.TP.5x11.5
CM113	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20
CM114	2401-002619	C-AL:47uF.20%.25V.GP.TP.5x11.5
CM115	2202-002037	C-CERAMIC.MLC-AXIAL:100NF.+80-20
CM209	2202-000830	C-CERAMIC.MLC-AXIAL:82PF.10%.5
CM211	2202-000830	C-CERAMIC.MLC-AXIAL:82PF.10%.5
CM212	2301-000175	C-FILM.PEF:15NF.5%.50V.7.1X3.5
CM213	2401-000030	C-ALUMINUM:22UE:20%.25V.GP.TP.5X11MM.5
CM218	2401-000030	C-ALUMINUM:22UF,20%,25V,GP,TP,5X11MM,5
CM301	2305-000665	C-FILM:CF922N63VT104-J-40/1053
CM302	2401-001496	C-AL:47UE20%.16V.GP.5X7MM.5MM
CM303	2202-002037	C-CERAMIC.MI C-AXIAI :100NE+80-20
CM304	2201-000499	C-CERAMIC DISC:390PE5% 50V SL 8 0X3 0 2
CM305	2401-001250	C-AL-4 7µF 20% 35V GP TP 4x5 5
CM307	2201-000345	C-CERAMIC DISC:200pE5% 50VSL TP6 3*3
CM308	2301-000175	C-FILM PEF: 15NE 5% 50V 7 1X3 5
CM309	2401-001363	C-AL:470UE20% 16V GPTP10X12
CM310	2401-000922	C-AL:22uE 20% 16V GPTP 5x5 5
CM311	2202-000127	C-CERAMIC MI C-AXIAI 10NE +80-2
CM312	2301-000224	C-FILM PEF-22NE5% 50V 7 4X3 9
CM313	2401-000603	C-AL:1UE.20%.50V.GP.5X11MM.5MM
CM314	2401-002235	C-FLECTROLYTIC: CE04W(T)16V10M
CM315	2401-002235	C-FLECTROLYTIC:CE04W(T)16V10M
CM316	2401-000603	C-AL:1UE 20% 50V GP5X11MM 5MM
CM317	2401-000603	C-AL:1UE 20% 50V GP5X11MM 5MM
CM318	2401-000598	C-AL:10E20% 50V GPTP 4x7 5
CM319	2202-000286	C-CERAMIC MI C-AXIAI :56PE 5% 50
CM320	2301-000383	C-FILM PEF:10nE5% 50V TP6x7x3 2mm 5mm
CM321	2202-000127	C-CERAMIC.MI C-AXIAI :10NE.+80-2
CM322	2202-002037	C-CERAMIC MI C-AXIAI 100NE+80-20
CM323	2401-002144	C-AL:47uE20% 16V GPTP5x11.5
CM324	2401-002144	C-AL:47uE20% 16V GPTP5x11 5
CM325	2202-002037	C-CERAMIC MI C-AXIAI 100NE+80-20
CM326	2202-002037	C-CERAMIC MI C-AXIAI 100NE+80-20
CM327	2401-000603	C-AL:1UE20% 50V GP5X11MM 5MM
CM328	2401-000603	C-AL:1UE.20%.50V.GP.5X11MM.5MM
CM329	2202-000819	C-CERAMIC MI C-AXIAI 47NE +80-2
CM330	2202-000127	C-CERAMIC MI C-AXIAI 10NE +80-2
CM331	2401-000603	C-AL:1UE.20%.50V.GP.5X11MM.5MM
CM332	2401-000603	C-AL:1UE20% 50V GP5X11MM 5MM
CM333	2401-002235	C-FLECTROLYTIC: CE04W(T)16V10M
CM334	2202-002037	C-CERAMIC MI C-AXIAI 100NE+80-20
CM335	2301-000356	C-FILM PEF-47nE 5% 50V TP 7 5x4 0x6 5 5m
CM336	2301-000356	C-FILM PEF 47nE 5% 50V TP 7 5x4 0x6 5 5m
CM337	2202-000127	C-CERAMIC MI C-AXIAI 10NE +80-2
CM338	2401-000603	C-AL-11 JE 20% 50V GP5X11MM 5MM
CM340	2202-002037	C-CERAMIC MI C-AXIAI 100NE+80-20
CM341	2401-002619	C-AL:47uE20% 25V GPTP5x11 5
CM342	2401-001537	C-AL: 47UE 20% 25V GP6 3X7MM 5
CM343	2202-002037	C-CERAMIC MI C-AXIAI 100NE+80-20
CM344	2202 002037
CM345	2202 000127
CM346	2401-000127	C-AL-111E 20% 50V GPTP 4v7 5
CM347	2701 000370	C_CERAMIC MIC_AXIAL 10NE ±20-2
CM348	2202-000127
CM349	2001_000520	R-CARBON-24KOHM 5% 1/8/Λ/ ΔΔ TP
CM350	2001 000000
CM351	2202-000127	C-CERAMIC DISC-33PE 5% 501/ NDO
0101001	2201-000403

Page 43

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification	Remark

CM501	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		DM106	0401-000005	DIODE;1N4148TAPG
CM502	2401-002462	C-ELECTROLYTIC;CE04WTAPG16V33M		DM301	0401-000005	DIODE;1N4148TAPG
CM503	2401-000914	C-AL;22UF,20%,16V,GP,5X11,5,TP		DM302	0401-000005	DIODE;1N4148TAPG
CM504	2401-001537	7 C-AL;47UF,20%,25V,GP,6.3X7MM,5		DM610	0402-000132	DIODE-RECTIFIER;1N4004,400V,1A,DO-41
CM505	2202-002037	C-CERAMIC, MLC-AXIAL; 100NF, +80-20		DM611	0401-000005	DIODE;1N4148TAPG
CM506	2301-000192	2 C-FILM,PEF;1NF,5%,50V,5.3X10MM		DM612	0402-000132	DIODE-RECTIFIER;1N4004,400V,1A,DO-41
CM507	2301-000342	2 C-FILM, PEF; 2.2nF, 5%, 50V, TP, 7.4x3.9x13mm,		DM613	0402-000132	DIODE-RECTIFIER;1N4004,400V,1A,DO-41
CM508	2401-000027	C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA		DM614	0402-000132	DIODE-RECTIFIER;1N4004,400V,1A,DO-41
CM509	2401-000455	5 C-AL;10uF,20%,35V,GP,TP,4x7mm,5mm		DM619	0402-000132	DIODE-RECTIFIER;1N4004,400V,1A,DO-41
CM510	2301-000383	3 C-FILM,PEF;10nF,5%,50V,1P,6x/x3.2mm,5mm		DM620	0401-000005	DIODE;1N41481APG
CIVI512	2202-002037			DIVI622	0402-000132	DIODE-RECTIFIER; IN4004,400V, IA, DO-41
CIVI513	2301-000224			DIVI/UT	0401-000005
CIVID14 CM515	2401-002299				AA04-000241
CM516	2301-000301	C-FILM DEE:8 2NE 5% 50V/6 5X2			6002-000507	SCDEW/ TADDING DH + 2 M2 I 12 7D
CM517	2301-000301	C-FILM PEE 6 8NE 5% 50V 6 5X5		FLM501	AA26-10006	CTRANS-IE 7ML BIAS - 7MM 3100PF
CM518	2301-000383	C-FILM PEF:10nE5% 50V TP6x7x3 2mm 5mm		GPM001	AA63-40311	A GROLIND-PLATE PCB - PBS TO 3 TVN334V -
CM519	2301-000383	3 C-FILM.PEF:10nF.5%.50V.TP.6x7x3.2mm.5mm		/\ICM101	1203-000298	IC-POSLEIXEDREG.:7809.TO-220.	H/SINK
CM520	2401-002619	C-AL:47uF.20%.25V.GP.TP.5x11.5		▲ ICM102	1203-000243	IC-POSI,FIXEDREG.:7812,TO-220,
CM521	2301-000254	C-FILM, PEF; 39NF, 5%, 50V, 7.5X3.5X6.5MM, 5MM		ICM301	1204-001495	IC-VIDEO PROCESS;LA71074M,QFP,100P,-,PLA
CM523	2305-000665	C-FILM;CF922N63VT104-J-40/1053		1CM601	AA13-00014	AIC-MCU;-,HD6433977RB71F,8BIT,QFP,TVN5
CM524	2202-000127	C-CERAMIC,MLC-AXIAL;10NF,+80-2		▲ICM603	1003-001162	IC-MOTORDRIVER;KA3082,SIP,10PIN,25MIL,D
CM603	2401-000603	3 C-AL;1UF,20%,50V,GP,5X11MM,5MM		▲ICM605	1203-000642	IC-RESET;572,TO-92,3P,-,PLASTI
CM604	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		LDM601	AA91-60317	AASSY-GUIDE,LED;-,ABS,V0,BLK,RED LED 03,T
CM605	2202-000295	C-CERAMIC,MLC-AXIAL;68PF,5%,50		LDM602	AA91-60318	AASSY-HOLDER,LED;-,ABS,HB,BLK,IR LED,TS-D
CM608	2202-000295	5 C-CERAMIC,MLC-AXIAL;68PF,5%,50		LM101	2701-000002	INDUCTOR-AXIAL;100UH,10%,4.2X9
CM611	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		LM301	2701-000002	INDUCTOR-AXIAL;100UH,10%,4.2X9
CM612	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		LM302	2701-000002	INDUCTOR-AXIAL;100UH,10%,4.2X9
CM613	2202-000127	C-CERAMIC,MLC-AXIAL;10NF,+80-2		LM303	2701-000002	INDUCTOR-AXIAL 100UH,10%,4.2X9
CIVI614	2401-001496			LIVI304	2701-000002	INDUCTOR-AXIAL 100UU 10%,4.2X9
	2202-000127			LIVI5UI	2701-000002
CM620	2401-002019			LIVIDUZ	2701-000002
CM621	2202-000222	C-CERAMIC,MEC-AXIAL, 3.5NI, 20%, 10%, 15F, 7		11/1503	2702-000120
CM622	2202-002017	C-CERAMIC MI C-AXIAI 10NF +80-2		LM601	2701-000002	INDUCTOR-AXIAI 10011H 10% 4 2X9
CM629	2202-000127	C-CERAMIC MI C-AXIAI 10NF +80-2		LM602	2701-000002	INDUCTOR-AXIAI 10011H 10% 4 2X9
CM630	2202-000127	C-CERAMIC.MLC-AXIAL:10NF.+80-2		OOVER	AA41-10982	APCB-VIDEO:V15A.1L,FR-1.330x245x1.6T.A1
CM631	2202-000162	C-CERAMIC,MLC-AXIAL;15PF,5%,50		PTM601	0604-001122	PHOTO-INTERRUPTER;TR,0.065%,150mW,DIP-4,
CM632	2202-000162	C-CERAMIC,MLC-AXIAL;15PF,5%,50		PTM602	0604-001122	PHOTO-INTERRUPTER;TR,0.065%,150mW,DIP-4,
CM633	2202-000162	C-CERAMIC,MLC-AXIAL;15PF,5%,50		QM101	0504-000118	TR-DIGITAL;KSR1003,NPN,300MW,2
CM634	2202-000162	C-CERAMIC,MLC-AXIAL;15PF,5%,50		QM102	0501-000316	TR-SMALLSIGNAL;KSA928A-Y,PNP,1
CM636	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		QM103	0504-000118	TR-DIGITAL;KSR1003,NPN,300MW,2
CM637	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		QM104	0501-000316	TR-SMALLSIGNAL;KSA928A-Y,PNP,1
CM638	2202-000719	C-CERAMIC,MLC-AXIAL;6.8nF,20%,16V,Y5R,TP		QM106	0501-000362	TRANSISTOR;KSC2328A-Y/2SC2655-
CM639	2202-000127	C-CERAMIC,MLC-AXIAL;10NF,+80-2		QM301	0501-000303	TR-SMALLSIGNAL;KSA733,PNP,250M
CIVI640	2401-000455	C-AL; 100F, 20%, 35V, GP, 1P, 4X / mm, 5mm		QIVI302	0501-000398	TR-SMALLSIGNAL;KSC945,NPN,60V,
CIVI64 I	2202-000127			QIVI303	0501-000303
CIVI043	2401-001250			QIVI304	0501-000398
CM645	2202-000127			0M306	0501-000398
CM646	2202-002013			OM307	0504-000112	TR-DIGITAL KSR2001 PNP 300MW 4
CM648	2301-000224	C-FILM.PFF:22NE.5%.50V.7.4X3.9		OM308	0504-000119	TR-DIGITAL:KSR1004.NPN.300MW.4
CM649	2401-001537	C-AL:47UF.20%,25V.GP.6.3X7MM.5		QM501	0501-000303	TR-SMALLSIGNAL:KSA733.PNP.250M
CM650	2202-000127	C-CERAMIC,MLC-AXIAL;10NF,+80-2		QM502	0501-000010	TR-SMALLSIGNAL;KSC1008,NPN,80V
CM652	2401-002619	C-AL;47uF,20%,25V,GP,TP,5x11,5		QM503	0501-000303	TR-SMALLSIGNAL;KSA733,PNP,250M
CM653	2202-000127	C-CERAMIC,MLC-AXIAL;10NF,+80-2		QM504	0501-000231	TR-SMALLSIGNAL;2SD1468SQ,NPN,3
CM654	2401-002619	P C-AL;47uF,20%,25V,GP,TP,5x11,5		QM505	0501-000231	TR-SMALLSIGNAL;2SD1468SQ,NPN,3
CM655	2202-000127	C-CERAMIC,MLC-AXIAL;10NF,+80-2		QM601	0504-000119	TR-DIGITAL;KSR1004,NPN,300MW,4
CM656	2401-000302	2 C-AL;100UF,20%,25V,GP,6X11MM,5		QM602	0504-000142	TR-DIGITAL;KSR2001,PNP,300MW,4
CM657	2401-000302	2 C-AL;100UF,20%,25V,GP,6X11MM,5		QM701	0504-000118	TR-DIGITAL;KSR1003,NPN,300MW,2
CM701	2202-002037	C-CERAMIC,MLC-AXIAL;100NF,+80-20		QM702	0504-000118	TR-DIGITAL;KSR1003,NPN,300MW,2
CM/02	2401-002009	C-AL;100UF,20%,16V,GP,1P,6.3X7		QM/03	0504-000118	IR-DIGITAL;KSR1003,NPN,300MW,2	- 0
CNIVIOU I	AA39-20159			REIVI701	AA59-60003		5
CINIVI3UT	3708-000395			RIVITUT	2001-001088
CNIMEDO	3710 000/05			KIVI 102 DI /102	2001-0002/3
CNIM601	2010-000400 0020_20602			RM103	2001-001122
CNM602	3711_003740	CONNECTOR-HEADER ROX 8P 2R 2mm STRAIGHT		RM104	2001-000273	R-FUSIBLE(S):680hm 5% 2\\/ AFTP 3 Qv10mm
CNM604	3708-001131	CONNECTOR-EPC/EC/PIC:5P1 25mm STRAIGHT	ı	RM105	2001-001107	R-CARBON(S):2200HM.5% 1/2W AA
CNM605	AA39-20071	DLEAD-CONNECTOR ASSY:YBNH025-12 67096-0		RM108	2008-000290	R-FUSIBLE:2.40HM.5%.2W.AFTP3
COVER	AA63-00006	AFRAME,TOP;-,TVN-502V,T0.5,SECC,-,		RM109	2008-001015	R-FUSIBLE;1.50HM,5%2WAF,TP39X10
DE+FD	6002-000522	SCREW-TAPPING;TH,+,2,M4,L15,ZP		RM301	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,
DM101	0402-000132	DIODE-RECTIFIER;1N4004,400V,1A,DO-41		RM302	2001-000577	R-CARBON;2KOHM,5%,1/8W,AA,TP,1
DM102	0402-000132	2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41		RM303	2001-000723	R-CARBON;4.3KOHM,5%,1/8W,AA,TP
DM103	0402-000132	2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41		RM304	2001-000241	R-CARBON;1.5KOHM,5%,1/8W,AA,TP
DM104	0402-000132	2 DIODE-RECTIFIER;1N4004,400V,1A,DO-41		RM305	2001-000563	R-CARBON;27KOHM,5%,1/8W,AA,TP,
DM105	0402-000132	2 DIODE-RECTIFIER:1N4004.400V.1A.DO-41		RM306	2001-001108	R-CARBON(S);22KOHM,5%,1/2W,AA,

Page 44

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Description ; Specification	Remark
RM307	2001-000200	) R-CARBON-10ΚΟΗΜ 5% 1/8₩/ ΔΔ ΤΡ		RM618	2004-001185	R-METAL 680K0HM 5% 1/8W 44 TP
RM308	2001-0002 /0	R-CARBON(S);2700HM,5%,1/2W,AA,		RM621	2004-001103	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM309	2001-000969	R-CARBON;750HM,5%,1/8W,AA,TP,1		RM623	2001-000290	R-CARBON; 10KOHM, 5%, 1/8W, AA, TP,
RM310	2001-000786	R-CARBON;47KOHM,5%,1/8W,AA,TP,		RM633	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM311	2001-000977	' R-CARBON;8.2Kohm,5%,1/8W,AA,TP,1.8x3.2m		RM634	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RIVI312 PM314	2001-000734	R-CARBON;4.7K0HM,5%,178W,AA,1P P.CAPBON;750HM,5%,178W,AA,TP1		RIVI636 PM638	2001-000429	R-CARBON: IKONM,5%, I/8W,AA, IP, I.8X3.2MM P. CARBON: 4 7KOHM 5%, 1/8W, AA, TP
RM314	2001-000977	R-CARBON:8 2Kohm 5% 1/8W AA TP1 8x3 2m		RM639	2001-000734	R-CARBON:1Kohm 5% 1/8W AA TP1 8x3 2mm
RM317	2001-000449	R-CARBON;2.2KOHM,5%,1/8W,AA,TP		RM640	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM318	2001-000989	R-METAL;820Kohm,5%,1/8W,AA,TP,1.8x3.2m		RM641	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM319	2001-000786	R-CARBON;47KOHM,5%,1/8W,AA,TP,		RM642	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RIVI320	2001-000241			RIVI643	2001-000429	CARBON: 1KONM, 5%, 1/8W, AA, 1P, 1.8X3.2MM
RM322	2001-00024	8 R-CARBON: 1.8Kohm.5%.1/8W.AA.TP.1.8x3.2m		RM645	2001-000734	R-CARBON:4.7KOHM.5%.1/8W.AA.TP
RM323	2001-000977	R-CARBON;8.2Kohm,5%,1/8W,AA,TP,1.8x3.2m		RM646	2001-000221	R-CARBON;1.2KOHM,5%,1/8W,AA,TP
RM324	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,		RM648	2001-000734	R-CARBON;4.7KOHM,5%,1/8W,AA,TP
RM326	2001-000508	R-CARBON;220KOHM,5%,1/8W,AA,TP		RM650	2001-000633	R-CARBON;30KOHM,5%,1/8W,AA,TP,
RM327	2001-000508			RIV1662	2001-000290
RM329	2001-000800	R-CARBON:33KOHM.5%,1/8W.AA,TP		RM664	2001-000290	R-CARBON: 10KOHM,5%,1/8W,AA,TP,
RM330	2001-000008	R-CARBON;15KOHM,5%,1/8W,AA,TP,		RM666	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM331	2001-000633	R-CARBON;30KOHM,5%,1/8W,AA,TP,		RM667	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
RM332	2001-000947	R-CARBON;7.5KOHM,5%,1/8W,AA,TP		RM668	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
RM333	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,		RM670	2001-001035	R-METAL:910hm,5%,1/8W,AA,TP,1.8x3.2mm
RM335	2001-000632	R-CARBON,5100HW,5%,1/8W,AA,TP,		RM672	2001-001035	R-INETAL, 9101111, 576, 176 W, AA, TP, 1.6X5.21111 R-CARBON:1800HM 5% 1/8W AA TP
RM336	2001-000472	R-CARBON;2.7KOHM,5%,1/8W,AA,TP		RM673	2001-000534	R-CARBON;2400HM,5%,1/8W,AA,TP,
RM337	2001-000734	R-CARBON;4.7KOHM,5%,1/8W,AA,TP		RM674	2001-000241	R-CARBON;1.5KOHM,5%,1/8W,AA,TP
RM338	2001-000008	R-CARBON;15KOHM,5%,1/8W,AA,TP,		RM676	2001-000864	R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM339	2001-000837	R-CARBON;51KOHM,5%,1/8W,AA,TP,		RM677	2001-000864	R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RIVI340 RM342	2001-000429	Y R-CARBOIN; I KONIII,5%, I/8W,AA, I P, I.8X3.2MIII ) R-CARBON-10KOHM 5% 1/8W/ΔΔ TP		RIVI678 RM679	2001-000522	R-CARBON;22KUHIVI,5%,1/8W,AA,1P, R-CARBON:51KOHM 5% 1/8W/ AA TP
RM501	2001-000230	R-CARBON: 470ohm.5%, 1/8W.AA, TP.1.8x3.2mm		RM680	2001-000534	R-CARBON:2400HM.5%.1/8W.AA.TP.
RM502	2001-000449	R-CARBON;2.2KOHM,5%,1/8W,AA,TP		RM681	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,
RM505	2001-000454	R-CARBON;2.2MOHM,5%,1/8W,AA,TP		RM682	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,
RM506	2001-000232	R-CARBON;1.3KOHM,5%,1/8W,AA,TP		RM683	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RIVI507	2001-00060	R-CARBON, 33KOHIVI, 5%, 1/8W, AA, IP, R-CARBON-1200HM 5% 1/8W/ ΔΔ TP		RIVI084 RM685	2001-000837	R-CARBON;51KUHIVI,5%,1/8W,AA,1P, R-CARBON:56Kohm 5% 1/8W/AA TP1 8v3 2mm	n
RM509	2001-000323	R-CARBON: 5.6Kohm.5%.1/8W.AA.TP.1.8x3.2mn	ı	RM686	2001-000864	R-CARBON:56Kohm.5%,1/8W.AA.TP.1.8x3.2mm
RM510	2004-001989	R-METAL;6200HM,5%,1/8W,AA,TP,1		RM687	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,
RM511	2001-000472	R-CARBON;2.7KOHM,5%,1/8W,AA,TP		RM688	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM512	2001-000977	R-CARBON;8.2Kohm,5%,1/8W,AA,TP,1.8x3.2m		RM689	2001-000010	R-CARBON;68Kohm,5%,1/8W,AA,1P,1.8x3.2mm
RM514	2001-000331	R-CARBON; 12KOHM, 5%, 1/8W, AA, TP, R-CARBON:1.2KOHM, 5%, 1/8W, AA, TP		RIVI090 RM691	2001-000429	R-CARBON; IKUIIII, 5%, 1/8W, AA, IP, 1.8X3.2IIIII R-CARBON: 1Kohm 5% 1/8W/ AA TP1 8x3.2mm
RM516	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,		RM692	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM517	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,		RM693	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM518	2001-000458	R-CARBON;2.20hm,5%,1/8W,AA,TP,1.8x3.2mm		RM694	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RM519	2001-000258	8 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m		RM695	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
RIVI520 RM521	2001-000780	) R-CARBON;4700111,5%,178W,AA,1P,1.8X3.21111 R-CARBON:1800HM 5% 1/8W/ΔΔ TP		RIVIO90 RM697	2001-000429	R-CARBON, IKUIIII, 3%, I/8W, AA, IP, I.8X3.2IIIII R-CARBON-1Kohm 5% 1/8W/ AA TP1 8x3.2mm
RM522	2001-000429	R-CARBON:1Kohm.5%.1/8W.AA.TP.1.8x3.2mm		RM699	2001-000429	R-CARBON:1Kohm.5%.1/8W.AA.TP.1.8x3.2mm
RM523	2001-000522	R-CARBON;22KOHM,5%,1/8W,AA,TP,		RM701	2001-001077	R-CARBON(S);1500HM,5%,1/2W,AA,
RM524	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm		RM702	2001-001077	R-CARBON(S);1500HM,5%,1/2W,AA,
KM527	2001-000786	R-CARBON:4/KUHM,5%,1/8W,AA,TP		RM/03	2001-001077	K-CARBON(S);1500HM,5%,1/2W,AA,
RM520	2001-000290	R-CARBON:TUKUHIVI,5%,1/8W/AA,1P, R-CARBON:47KOHM 5% 1/8W/AA TP		SM601	AA03-40313/ AA91-60310/	чэпіеци-воттоілі;-,экте,10.5,-,10103340 4 ASSY-HOLDER SENSOR∙- ARS HR RLK TR LED T
RM530	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,		SM602	AA91-60319/	AASSY-HOLDER,SENSOR;-,ABS,HB,BLK,TR LED,T
RM531	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm		SPLATE	AA63-40301	ASHIELD-PLATE;STEEL PLATE S30 T0.5
RM532	2001-000645	R-CARBON;330KOHM,5%,1/8W,AA,TP		SPRING	AA61-00050/	ASPRING-DOOR;-,SUS304,0.5,OD6,H9.7,N8,-,T
RM533	2001-000812	2 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2mn D CARBON:10KOUM 5%, 1/8W,AA,TP,	۱	SWM601	AA34-20001	ASWITCH-MODE;1,25x14.6x29.8mm,BK,DC5V
RIVI534 RM601	2001-000290	R-CARBON, IUKOHIVI, 5%, I/8WV, AA, IP, R-CARBON-1Kohm 5% 1/8W/ AA TP1 8v3 2mm		SWIVI602 SW/M701	AA34-40001/ 3404-000244	SWITCH-REC.; IEA,37.5X14.4MM,BK,DC5V SWITCH_TACT:15V/20M/A 90_170GF
RM602	2001-000786	R-CARBON:47KOHM.5%,1/8W.AA.TP.		SWM702	3404-000244	SWITCH-TACT:15V.20MA.90-170GF.
RM603	2001-000435	R-CARBON;1MOHM,5%,1/8W,AA,TP,1		SWM703	3404-000244	SWITCH-TACT;15V,20MA,90-170GF,
RM604	2001-000449	R-CARBON;2.2KOHM,5%,1/8W,AA,TP		SWM704	3404-000244	SWITCH-TACT;15V,20MA,90-170GF,
RM605	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm		SWM705	3404-000244	SWITCH-TACT;15V,20MA,90-170GF,
	2001-000449			SWM/06	3404-000244	SWITCH-TACT;15V;20MA;90-170GF;
RM608	2001-000290	R-CARBON:1000HM15%,178W/AA,1P, R-CARBON:1000HM 5% 1/8W/AA TP		SWM708	3404-000244	SWITCH-TACT, 159,2000A,90-170GF SWITCH-TACT:150/20MA 90-170GF
RM609	2003-002129	P.R-METALOXIDE(S);3.90hm,5%,2W,AF,TP.3.9x		SWM709	3404-000244	SWITCH-TACT;15V,20MA,90-170GF,
RM610	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,		VRM601	2103-000669	VR-SEMI;NVZ6TLTA10KB10KBCERMET
RM612	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm		XTM301	2801-003610	CRISTAL-UNIT 3.57MHZ
RM613	2001-000429	R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm		XTM601	2801-003293	CRYSTAL-UNIT;10MHZ,50PPM,28-AA
	2001-000290	K-CARBON, IUKUHIVI, 5%, 1/8W, AA, 17, D.CARRON-1MOHM 5%, 1/8W, AA, TD1		X11V1602 7DM102	2801-003224
RM616	2001-000430	R-CARBON;1Kohm.5%.1/8W,AA.TP.1.8x3.2mm		ZDM701	0403-000555	DIODE-ZENER;MTZ12.12V.11.4-12.
RM617	2001-000290	R-CARBON;10KOHM,5%,1/8W,AA,TP,

Page 45

Loc. No.	Code No.	Description ; Specification	Remark	Loc. No.	Code No.	Descrip
		ASSY-PCB,A/V

* LA95-40005SASSY-PCB,A/V;-,KCV13A,V15A,13,19


05VER	AA41-10290F PCB-A/V;KH1,1L,FR-1,227x50.5x1.6T,-,-
CV602	3711-002645 POST-HEADER;67094-006(AUTO)
CV602	AA39-20027ALEAD-CONNECTOR, ASSY; -, 67096-006, S, 6P, 300
JA01	3722-000171 JACK-RCA;1P,3.4MM,-,AU
JA02	3722-000180 JACK-RCA;1P,3.4MM,-,SN
JE01	3722-000145 JACK-PHONE;1P,3.6MM,-,MBAG
R605	2001-001187 R-CARBON(S);750HM,5%,1/2W,AA,T
R606	2001-001187 R-CARBON(S);750HM,5%,1/2W,AA,T

ASSY-ACCESSORY

* AA97-20032FASSY-ACCESSORY;V15A,MEX,TVI TVCR


A/ROD	L7000-0130 ANT-RODVHF;4SDODIPOLE500MMBRN
BATT	4301-000121 BATTERY-MN;1.5V,-,AAA,10.5X44.
CR-MUL	31499-009-120CR-MULTIPLE;MED-C271,R1-2M
I/B	AA68-00010A MANUAL-USERS; V15A, SPA, TM46, -, W/P100(G),
PATCH	AA39-40001F CABLE-RCA;-,RCA,150MM,0.12/10,
T/MATC	L2759-115-050TRANS-MATCHING;R300-R75CSA
T/REG	L6000-0082-020TARJETADEREGISTRO;8.5X11,80GL,MEX

REMOCON

* AA59-10026QREMOCON;-,TM46,SS,SZM644E,39,4HD,-,L/G

Page 46

9. Block Diagram

Page 47

11. PCB Layout

11-1 TV Main

Loc. No. X

:. No.

Page 48

11-2 Video Main

Page 49

Page 50

10. Wiring Diagram

V15A M/DECK BLOCK DIAGRAM

Page 51

12. Schematic Diagrams

12-1 VCR (AV-BLOCK)

Page 52

12-2 VCR (SYSTEM BLOCK)

Page 53

Page 54

12-4 TV (MAIN BLOCK)

Page 55

12-4-1 Waveform

		TP35
Stopped		2	1998/07/01 14:16:0
	CH2#2V DC 10:1		20us/div (20us/div) NORM30M5/s
	•	~	~


n

	ļ	Į
4	┙╎╎┢╍┥╍╍┾	┉┉┥┈┝┉┿┉╼
			CH2
CH2 V/DI CAL	VAR	1	2
Smoothing : OFI	F CH1 : 0.0V	Main : 10K	Mode : AUTO
BW : FOLL	CH3 : 0.0V CH4 : 0.0V	Zoom : 100	Type : EDGE CH2 ∳ Delay : 0.0 Hold Off : MENIMU
BW : FOLL	CH2 : 0.07 CH3 : 0.07 CH4 : 0.07	TP36	Type : EDGE CH2 5 DHay : 00 Hold Off : MENDAU
Stopped	CH2 BUV CH3 BUV CH4 BUV	TP36	Type : EDGE CH2 ∮ Deloy : 0.0 Held Off : MBNDAU 1998/027/01 14:284 2016/div
Stopped	CH2 LD0V CH3 6.07V CH4 0.07V CH4 0.07V	TP36	Type : EDGE CHE ∳ Deloy : 0.0 Held Off : MENDAU 1998/02/01 M:284 (2844/db/ (2844/db/ NORM-20M5/s
Stopped			Type : EDGC CH2 & Detexy : 0.0 Held Off : MERIMA 1998/027/01_14:284 2016/04 (2016/04 NORM-2016/29
Stopped		TP36	Type : EDE CHE & Deby : 00 Hest Off : MERIAN 1998/02/01 14:28k 20ke/db (25ke/db) 20ke/db
Stopped			Type : EDE CHE & Deby : 00 Heed Off : MERIAN 1998/02/01 14:28k 28ks/db (28ks/db (28ks/db)
Stopped			Type : EDGE CHE da Head OTT : MERIDAD 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/01 14:28:4 2008/07/07/01 14:28:4 2009/07/07/07/07/07/07/07/07/07/07/07/07/07/
Stopped			Type : EDGE CF2 & Type : EDGE CF2 & Held Off : MaDBAN 1998/07/01 14:28: 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/54 2014/5
Stopped			1999/02/01 1455 1999/02/01 1455 1999/02/01 1455
Stopped			1999/02/01 14504

Stopped

SAMSUNG CXJ1331, CXJ1331AX, CXJ1331TUCX, CXJ1352, CXJ1352AX Service manual & schematics

Television Video Cassette Recorder

SERVICE Manual

Television Video Cassette Recorder

CONTENTS

1. Precautions

1-1 Safety Precautions

1-1 Safety Precautions (Continued)

1-2 Servicing Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

2. Specifications

3. Alignments and Adjustments (VCR)

3-1 Mechanical Adjustments

3-1-1 Tape Transport Adjustment

3-1-1(A) PARTS LOCATIONS

3-2 Adjustments

3-2-1 Preadjustment

3-2-2 (B) A/C HEAD TILT ADJUSTMENT

3-2-2(D) A/C HEAD POSITION (X-POINT) ADJUSTMENT

Note :

SCOPE SETTINGS

3-2-2(E) LINEARITY ADJUSTMENT (GUIDE ROLLER S.T ADJUSTMENT)

Note :

3-2-3 Check Switch over from RPS to Playback Mode

3-2-4 Envelope Check

3-2-5 Tape Wrinkle Check

3-3 Reel Torque Adjustments

3-4 Location Adjustment and Confirmation of Tension Post

Note :

3-5 Circuit (SERVO) Adjustment

3-5-1 Adjust the switching point.

5. Timing Chart

5-1 Program S/W Timing Chart

6. Troubleshooting

6-1 No Power (No Raster, No Sound, Power Led Off)

6-2 No Picture or Raster

6-4 No Vert Scan

6-5 No Color

6-8 No Playback

6-9 REC Doesn't Operate

6-12 "Forward Direction Search Screen" Doesn't Operate

6-15 Capstan Doesn't Rotate

6-19 No Color During Playback

7. Exploded View & Parts List

7-1 TT14A54X

7-2 TT20A54X

7-4 Mechanical Parts (Bottom Side)

8. Electric Parts List

8-1 TT14A54X/XAX (TT20A54X/XAX and TT14A54X/XAX Dissimilar Parts)

ASSY-SPEAKER

ASSY-CRT

8-2 TT20A54X/GSU (TT20A54X/XAX and TT20A54X/GSU Dissimilar Parts)

8-3 TT20A54X/RCL (TT20A54X/XAX and TT20A54X/RCL Dissimilar Parts)

8-3 TT20A54X/XAX

ASSY-CRT

ASSY-ACCESSORY

REMOCON

9. Block Diagram

11. PCB Layout

11-2 Video Main

10. Wiring Diagram

12. Schematic Diagrams

12-1 VCR (AV-BLOCK)

12-2 VCR (SYSTEM BLOCK)

12-4 TV (MAIN BLOCK)

12-4-1 Waveform