Samsung TSL3295HFX, TSL3295HF, TSL3294HFX, TSL3294HF, TSL2795HFX Owner’s Manual

...

ELECTRONICS

Owner's

Instructions

l Warninq ! Important

Safety Instructions

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

dangerous to make any kind of contact with any inside part of

This symbol indicates high voltage is present inside, It is

this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this producL

Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820 40 of the National Electrical Code (Section 54 of

Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the

grounding system of the building as close to the point of cable entry as practical.

Caution: FCC/CSA regulations state that any unauthorized ehanges or modillca tlons to this equipment may void the user's authority to operate it.

Caution: To prevent etectric shoek, match the wide Made of plug to the wide slot,

and fully insert the plug.

Attention: pour eviter les chocs electriques, introduire la lame le ptus large de la fiche dans la borne correspondante de la prise et pousserjusqu'au fond.

Important: One Federal Court has held that unauthorized recording of

copyrighted TV programs is an infringement of U.S. copyright laws. Certain Canadian programs may also be copyrighted and any unauthorized

recording in whole or in part may be in violation of these rights.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

As an ENERGY STAR Partner, Samstmg Electronics America, Inc. has determined that this product or product

model meets the ENERGY STAR guidelines for energy efficiency

Thank You for Choosing Samsung

Thank you for choosing Samsung! Your new Samsung TV represents the latest in television technology, We designed it with easy to use on screen menus and closed captioning capabili ties, makhlg it one of the best products in its class. We are proud to offbr you a product that will provide convenient, dependable service and enjoyment fur years to come.

Important Safety Information

Always be careful when using your TV receiver. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and

maintaining your machine.

• Read all safety and operating instructions before operating your T_

• Keep the safety and operating instructions for future re%fence.

• Heed all warnings on the TV receiver and in the operating instructions.

• Follow all operating and use instructions.

• Unplug the TV receiver from the wall outlet befure cleaning. Use a damp cloth; do not use liquid or aerosol cleaners.

• Never add any attachments and/or equipment without approval of the manufacturer. Such additions can increase the risk of fire, electric shock, or other personal injury,

• Do not use the TV receiver where contact with or immersion in water is a possibility, such as near bath tubs, sinks, washing machines, swimming pools, etc.

• Do not place the TV on an unstable cart, stand, tripod, bracket, or table where it can fail. A falling TV can cause serious injury to a child or adult, and serious damage to the appliance. Use only with

a cart, stand, tripod, bracket, or table recommended by the manu facturer or sold with the TV[ Pollow the manufacturer_ instruc

tions when mounting the unit, and use a mounting accessory rec ommended by the manufacturer. Move the TV and cart with care.

Quick stops, excessive force, and uneven surfaces can make the unit and cart unsteady and likely to overturn.

• Provide ventilation fur the TV receiver. The unit is designed with slots in the cabinet for ventilation to protect it from overheating. Do not block these openings with any object, and do not place the TV receiver on a bed, sofa, rug, or other similar sur

face. Do not place it near a radiator or heat register. If you place the TV receiver on a rack or bookcase, ensure that there is adequate ventilation and that you've followed the manufactur er_ instructions fur mounting.

• Operate your TV receiver only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer

or local power company

• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the

power outlet only one way If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.

SAFELY

• Protect the power cord. Power supply cords should be routed so that they won't be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, con venience receptacles, and the point where they exit from the unit.

• Unplug the TV from the wall outlet and disconnect the antenna or cable system during a light ning storm or when left unattended and unused for long periods of time. This will prevent dam

age to the unit due to lightning and power line surges.

• Avoid overhead power lines. An outside antenna system should not be placed in the vich]ity of overhead power lines or other electric light or power circuits or where it can fail into such

power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.

• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric

shock.

• Do not insert anything through the openings in the unit, where they can touch dangerous volt age points or damage parts. Never spill liquid of any kind on the TV

• Ground outdoor antennas. If an outside antenna or cable system is connected to the TV_be sure the antenna or

EXAMPLEQF ANTENNAGROUNDING

cable system is grounded so as to provide some protection against voltage surges and built up static

charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70 1984, provides infurmation about proper grounding of the mast and supporting structure,

grounding of the lead in wire to an antenna discharge unit, size of grounding conductors, location of antenna

discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

• Do not attempt to service the TV yourself. Refer all servicing to qualified service personnei. Unplug the unit from the wall outIet and refer servicing to qualified service personnel under the

fullowing conditions:

when the power supply cord or plug is damaged if liquid has been spilIed on the unit or if objects have fallen into the unit

if the TV has been exposed to rain or water if the TV does not operate normally by following the operating instructions if the TV has been dropped or the cabinet has been damaged

when the TV exhibits a distinct change in performance

• If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive

work by a qualified technician to restore the TV to normal.

• When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in additional damage to the unit.

• Upon completion of any service or repairs to this TV] ask the service technician to perform safety checks to determine that the TV is in a safe operating condition.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation.

This television receiver provides display of television closed captioning in accordance with

2 s_._ 15.119 of the FCC rules.

CONTENTS ]

Chapter 1: Your New TV ............... 1.1

List of Featuzes ......................................... 1,1

Familiarizing Yuursetf with Yuuz New TV ..................... 1,2

Front Pane[ Buttons .............................. 1,2

Side Panet Jacks ................................. 1,3

Rear Pane[ .Jacks ................................. 1.4

Remote Control ................................. 1.5

Chapter 2: Installation ................ 2.1

Connecting VHF and UHF Antennas ........................ 2.1

Antennas with 300 ohm Flat %vin Leads .............. 2.1

Antennas with 75 ohm Round Leads ................. 2.2

Separate VHF and UHF Antennas .................... 2.2

Connecting Cable TV .................................... 2.2

Connecting a VCR ...................................... 2.,5

Connecting a DVD Player ................................. 2.7

Connecting a Digital TV Set Tup Box ........................ 2.7

Connecting a Surzound Speakers ........................... 2.8

Connecting a Speakezs (Vaziable Autio output) ................. 2.8

Connecting a Camcorder ................................. 2.9

Installing Battezies in the Remote Control ..................... 2.10

Cabte without a Cable Box ......................... 2.2

Connecting to a Cable Box that Desci-amb[es

All Channels .................................... 2.3

Connecting to a Cable Box that Desczamb[es

some Channels .................................. 2.3

Connecting an S VHS VCR......................... 2.6

Connecting a Second VCR to Record from Yuur TV ...... 2.8

1 (]ON] EN] S

Chapter 3: Operation .................. 3.1

Turning the TV On and Off................................ 3.1

Plug & Play Featuze ..................................... 3.1

Viewing the Menus and On Sczeen Displays ................... 3.3

Viewing the Menus ............................... 3.3

Viewing the Display .............................. 3.3

Selecting a Menu Language ................................ 3.4

Memozizing the Channels ................................. 3.5

Selecting the Video Signal source .................... 3.5

Stozing Channels in Memozy (Automatic Method) ....... 3.6

Adding and Ezasing Channels (Manual Method) ........ 3.7

Changing Channels ..................................... 3.7

Using the Channel Buttons ......................... 3.7

Dii-ectly Accessing Channels ........................ 3.7

Using the Pre CH Button to select the PIevious Channel . . 3.7

Adjusting the Vdume .................................... 3.8

Using Mute ..................................... 3.8

Labeling the Channels ................................... 3.9

Setting the Clock ....................................... 3.10

Customizing the Picture .................................. 3.13

Using Automatic Picture Settings ........................... 3. ] 4

Customizing the Sound .................................. 3. ] 5

Using Automatic Sound Settings ............................ 3.16

Viewing a VCR or Camcozdez '.Cape.......................... 3.17

CONTENTS

Chapter 4: Special Features ............ 4.1

Customizing Yuuz Remote ContzoI .......................... 4.1

Setting Up Youz Remote Contzol to Opezate Yuur

VCR (or DVD) .................................. 4.1

Setting Up Youz Remote Contzol to Opezate Yuur

Cable Box...................................... 4.3

Fine Tuning Channels .................................... 4.4

LNA(Low Noise Amplfftez) ................................ 4.5

Digital Noise Reduction .................................. 4.@

Tilt .................................................. 4.7

Changing the Sczeen Size ................................. 4.8

Freezing the Picture ..................................... 4.9

Using the R.surf ........................................ 4.9

Special Sound Options: Dolby Surround, MTS, Auto Vdume and

Headphone ............................................ 4. l0

Dolby Pzo Logic ................................. 4.10

Choosing a Mutti Channel Sound (MTS) Soundtrack ..... 4.11

Adjusting the Headphone Sound .................... 4.12

Auto Volume ..................................... 4.13

Switching the Internal Speakezs On/Off ........................ 4.14

Setting the On/Off Timez ................................. 4.15

Setting the Steep Timer ................................... 4. l@

Viewing Ctosed Captions ................................. 4.17

Viewing Picture in Pictuze ................................ 4.18

Activating Pictuze in Picture ........................ 4.18

Selecting a Signal Source (External A/V) for PIP ......... 4.19

Swapping the Contents of the PIP image and Main image . 4.19

Changing the PIP Charmer ......................... 4.19

Changing the Location (Rotating) the PIP Window ...... 4.19

Changing the Size of the PIP Window ................ 4.19

Scanning the Avaitable Channels .................... 4.19

Using the VChip (Option) ................................ 4.20

Setting Up Youz Pezsonal ID Number (PIN) ............ 4.20

How to Enabte/Disabte the VChip ................... 4.21

How to Set up Restzictions Using the "TV guidelines" . . .. 4.21

How to Set up Restzictions using the MP/\A Ratings:

G, PG, PG 13, R, NC 17, X ........................ 4.23

How to Reset the TV after the VChip Blocks

a Channel ("Emergency Escape") .................... 4.24

Chapter 5: Troubleshooting ............ 5.1

Identifying Pi-oblems .................................... 5.1

Appendix ........................... A.1

Cteaning and Maintaining YuuzTV.......................... A.1

Using Yuuz TV in Anothez Countzy ......................... A.1

Specifications .......................................... A.1

( _H_H_s 2

YOUR NEW TV

List of Features

Your TV was designed with the latest technology. This TV is a high performance unit that includes the following special features:

• Easy to use remote control

• Easy tO use on screen _]erlu system

• Automatic timer to turn the TV on and off

• Adjustable picture and sound settings that can be stored in the TV_ memory

• Automatic channel tuning for up to 181 channels

• A special filter to reduce or eliminate reception problems

• Fine tuning control fur the sharpest picture possible

• A built in multi channel sound decoder foF stereo and bilingual listening

• Built in dual channel speakers

• A special sleep timer

• Double screen

• Headphone jack fur private listening

• 16:9 letter box furmat available depending upon sourc

(2HAP] k ON YOll NEW ]V _ .

I Your NEw TV

Familiarizing Yourself with The TV

Front Panel Buttons

The buttons on the front pane[ corm-o[ your TV% basic features, includin 8 the on screen

menu. Tu use the more advanced f'eatures, you must use the remote control.

1.2 (2HAP] k ()N YO{I NEV_ IV

0 TV/VIDEO

Press this button to display a menu of all the available signal sources, When the menu appears, use the CH buttons to highlight a particular source, and then press the VOL+button to select it,

0 MENU

Press to see an on screen menu of your TVrsfeatures,

0 VOLUME-, +

Press to increase or decrease the volume, Also used to select items on the on screen menu.

0 CH _" and CH ,&

Pressto change channels. Atso press

to highlight various items onthe

On screen menu,

0 POWER

Pressto turn the TV on and off,

0 Remote Control

Sensor

Aim the remote control towards this spot on the TV.

YOUR NEW TV ]

Side Panel Jacks

Yuu can use the side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For in%rmation on connecting equipment, see pages 2.1 2.9.)

The TV illustration shown does not necessary match the design of your TV set.

O AUDIO IN jacks

Usedto connect the audio signals from acamcorder or video

game,

O VIDEO IN jack

Usedto connect a video signal from a camcorder or a video game.

SUPER VIDEO IN jack Used to connect an S Video signal from a camcorder or a video game,

O HEADPHONE JACK

Connect aset of external headphones to thisjack for private listening.

(]HAP] h ON YOll NEV_ IV 1.3

Your NEw TV ]

Rear Panel Jacks

Use the rear pane[jacks to connect an A/V component that will be connected continuously, such as a VCR or a lasezdisc playen

Because there are two sets of input jacks, you can connect two different AA/ components (i.e., a VCR and a lasezdisc, 2 VCRs, etc.)

For more infomlation on connecting equipment, see pages 2.1 2.9.

O, OVIDEO INPUTS

Video signals from VCRs,laserdisc

players and similar devices (Three sets

are availaMe: AVl, AV2 andAV3),

_, _ AUDIO INPUTS

Audio signals from VCRs,laserdisc

players and similar devices.

O AUDIO-VIDEO

MONITOR OUTPUTS

Connect to the audio/video inputjacks of a

recording VCR, Note:The monitor out does not operate in DVD or

DTVmode,

0 SURROUND OUTPUTS

Connects to a rear surround amp: Surround Left,

Surround Right and Center. Hereare two ways to connect an audio amplifier: 1,TV amp- speaker

2.TV speaker(amp built in)

SUPER VIDEO IN

S Video signal from an S VHS VCRor DVDplayer,

O DVD & DTV VIDEO INPUTS

Connects component video from a DVD player & Set-TopBox,

DVD & DTV AUDIO INPUTS

Connect to the audio outputjacks of a DVD player or SETTOPBOX.

@ VHF/UHF

Connectto anantennaorto acableTVsystem.

1.4 (2HAP] k ON You NEV_ ]V

Your NEw TV ]

Remote Control

You can use the remote control up to about 23 feet from the TE When using the remote,

always point it directly at the T_

You can also use your remote control to operate your VCR and cable box. See page 4.1

for details.

O Power

Turnsthe TVon and off.

0 +100

Pressto select channels over 100. For example, to select channel

121,press" +100: then press "2" and"1 ,"

0 Mute

Pressto temporarily cut off

the sound.

0 OH& and OHm"

(Channel Up/Down)

PressCHA or CHV to change channels. (Also used to highlight

selections on the on screen menus,)

VOL -, VOL + Press increase or decrease the

volume, (Also used to make selec tions onthe on screen menus.)

0 Still picture

Pressto stop the action during a particular scene. Press again to

resume normal video.

0 P. Mode

Adjust the TVpicture by selecting one of the preset

factory settings (or select your

personal, customized picture settings).

S.Mode

Adjust the TVsound by selecting oneof the preset factory settings (orselect your personal customized sound settings).

0 VCR controls

Stop

Pressto stop a tape in your VCR.

iiiilililililililililil

MODE

Selects a target device to be con

trolled by the Samsung remote

control (i,e,,TV,VCR, Cablebox, or DVD).

Pre-CH

Tunestothepreviouschannel

TV/Video

Pressto display all of the available video sources (i.e., Antenna/cable, VCR,DVD, Video

1-4 andS Video 1-2).

Displays the main on screen menu.

BOSurround Selects one of Phantom modes

(Off,Normal, Phantom or Wide).

@ PIP

Activatespictureinpicture,

Pressto rewind a tape,

Pla_/Pause

Pressto playor pause the tape.

FF (Fast Forward)

Pressto fast forward a tape.

(:I{A}'][}/ ()N{ Y()[I N}W ]V 1.5

I Your NEw TV

Remote Control (continued)

@ Display

Presstodisp]aythecurrent channel and the audio video

settings.

@ Sleep

Pressto select a preset time interval for automatic shutoff,

Aspect

Presstochangethescreensize,

@ V.chip (Option)

Pressto set up and activate the parental locks,

_) PiP Controls

Locate

Pressto movethe PIPwindow to any of the four corners of the TV

screen,

Scan

Pressto memorize(scan) the available channels,

Source

Pressto select one of the avai{able signal sources for the

PIPwindow.

':....... =.... =-:==J il

1_ R.surf

Press the R,surfbutton to auto- matically return to a preferred

channel after a useepreset time delay,

Set Used during set up of this

Samsungremote control, so that it will work compatibly with

other devices (VCR,cabie box, etc.)

1_ MTS (Multichannel

Television Stereo)

Press to choose stereo, mono or Separate Audio Program (SAP

broadcast).

Add/Erase

Press to add or erase channels in the TV's memory.

Exchangesthe video signal that is currently displayed on the main screen with the signal

in the PIP window.

Size

Pressto makethe PIPwindow double, large or small.

Displays the available channels in sequence. (These buttons change channels in the PIP win

dow only).

1.6 <:.,,},,._ (]N{ Y(_II N}w ]V

INSTALLATION

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see "Antennas with

300 ohm Flat _vin Leads," below.

If your antenna has one lead that looks like this, see "Antennas with 75 ohm

Round Leads," oil page 2.2.

If you have two antennas, see "Separate

VHF and UHF Antennas," ollpage 2.2.

Antennas with 300-ohm Flat Twin Leads

If"you are using an offair antenna (such as a roof antenna or "rabbit ears") that has 300-ohm twin flat leads, follow the directions below.

r ace the wires from the [wJn eads under the screws on the 300_75

ohm aeautor mot su[

ledl Use a screworlv-

er to tighten the screws.

Plug the adaptor into the

bottom of the back

INSTALLATION ]

Antennas with 75-ohm Round Leads

1 i

Plugtheantennalead

intotheVHF/UHF terminalonthebottom

of the back panel.

Separate VHF and UHF Antennas

If you have tvvo separate antennas for your TV (one VHF and one UHF), you must combine tile two antenna signals before connecting the antennas to tile T_/_This procedure requiresa an optional combiner adaptor (available at most electronics shops).

Connectbothantenna leadstothecombiner.

Plugthecombinerinto theVHF/UHFtermina!

on thebottomofthe rearpanel

Connecting Cable TV

To connect to a cable TV system, foBow tbe instructions below.

Cable without a Cable Box

Because this TV is

cable_ready, you do not need a

Plug the incoming cable cable box to view unscrambled cable

intotheVHF/UHF channels. antenna terminat 0n

back ofthe IV.

2, 2 < H,',a']l}a J\_o INs],_J] AnON

INSTALLATION ]

Connecting to a Cable Box that Descrambles All Channels

Findthe cable that is connected to the _ _

ANTENNA OUTterminaI

Onyour cable box, ..................' _

Connect the other end

of this cable to the VHF/UHFantenna

terminal onthe back of the TV.

-.9 This terminal might be labeled "ANT OUT," "VI[F OUT," or simply,

"OUT."

Connecting to a Cable Box that Descrambles Some Channels

If"your cable box descrambles only some channels (such as premium channels), fullow the

hlstructions below. You wilI need a two way splitter, an RF (A/B) switch, and fuur lengths of' coaxial cable. (These items are available at most electronics stores.)

Findand disconnect the f

cable that is connected d'totheANTENNA N _ _

terminal or your L _ '

CaD _ DOX

Connect this cable [o two-way spit[tel

Cable

8platmr

Connect a coaxial cable between an OUTPUT

termtnat onthe spmter and the IN terminal on

the cable box,

InCOming

Cable

--4 This terminal might be labeled "ANT IN," "VI [F IN," or simply,

"IN."

CableBox

(:IIAP] }/ IV() ]NSI%I]AI /IN 2.3

INSTALLATION ]

Connect a coaxial cable

OUTterminal 0nthe

between the ANTENNA cable box andthe B- tN Cable _

terminal onthe A/B Splitter RF(NB) switch.

Connect another cable between the other OUT

terminal onthe splitter

and the A* IN terminal

on the RF(A/B)switch,

Incoming

Cable

Splitter

Connect the Iast coaxiaI cable between the OUT

terminal onthe RF(A/B) switch and the VHF/UHE Spinier

terminal onthe rear of

Cable Box

the TV.

GableBox Switch

CableBox Switoh

RF(A/B) VHF/UHF

75Q

13/Rear

After you've made this connection, set the A/B switch to the "A" position foz normal viewing. Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch to "B," you will need to tune youz TV to the cable box's output channel, which is usu ally channel 3 or 4.)

2.4 ( ,,A,.,,,_h,o: ]NS,.,,,A,,ON

INSTALLATION ]

Connecting a VCR

These instructions assume that you have akeady connected youz TV to an antenna oz a cable TV system (according to the instructions on pages 2.1 2.3). Skip step 1 if you have not yet

connected to an antenna or a cable system.

Connectthecableor / E

VCR Rear Panel

antennatothe _ _II_Q. _ _ ANTENNAINterminat I_ab_, @_ _)_ ®

onthe backoftheVCR. Arr_n_

Connect a coaxial cable between the ANTENNA OUTterminal onthe VCRand the antenna terminai onthe TM.

A coaxiaI cable is usuaIiy included with a VCR. (If' not, check your local electronics

s[oie).

Connect a set of audio __ cables between the

AUDIOOUTjacks onthe VCRand the AUDI0

jacks onthe fV.

r L

CoaxialCable

VCR Rear Panel TV Rear Panel

l_/RearPanelVCR RearPanel

If'you have a "mono" (non stereo) VCR, use the _connector (not supplied) to hook up to the left and right audio input jacks of the TV] If'your VCR is stereo, you must con

nect two cables.

VCR Rear Panel TV Rear Panel

Connect a video cable between the VIDEOOUT

jack on the VCRand the

Video Cable

VIDEOjack on the TV,

[_ollow the instructions in "Viewing a VCR or Camcorder Tape" to view your VCR tape.

(]]]'kl'll l r\_(): INs],_] [,\]l() 2,5

I I

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S Video signal from an S VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR.)

VCR Rear Panel ]_ Rear Panel

Connect a set ofaudiQ

cables between the

AUDIO OUTjacks on th_

VCRand the AUDIO iNPUT 3`jackson the TV,

VCR RemPanel TV Rear Panel

Audio Cable

Make sure the jacks you are using are underneath the number "3."

VCRRearPanel W RearPanel

Connect anS-video cable between the S-VideoCable

S-VIDEOOUTjack on _: the VCRand the

S-VIDEOINPUT

`jackon the TV.

An S video cable ts usually included vvith all S VHS VCR. (If not, check your Mcal electronics store.)

Connecting a Second VCR to Record from the TV

Your TV can send out signals of its picture and sound to be recorded by a second VCP,.

Tu do this, connect your second VCR as fullows:

Connecta set ofaudio

cablesbetweenthe

AUDIO OUTjacks on the TVandthe AUDIO !N AudioCable

,jacksontheVCR.

(The VCR input jacks might be either on the front or on back of the VCR.)

i 2 w RearPanel

Connectavideocable betweentheVIDEOOUT

.jackontheTVandthe

VIDEOtNjack onthe

VCR.

Refbr to your VCR_ instructions for more information about how to record using this kind

of connection.

2, 6 ( H,,,aq_}_ i_s],v] AHO_

VCR InputPanel

VideoCable

_" !i i

I I ii

INSTALLATION ]

Connecting a DVD Player

The rear paneljacks on your TV make it easy to connect a DVD player to your TM

Connect a set of audio cables between the AUDIO INPUT 2 laCKSon the TVand the AUDIO

OUTjacKs on the DVD p_aye_

Connect a video cable between the DVD-tN _v

_b,Pri acksonthe IV

andthe DVD-OUT{Y.Pb

_r)jacks on the DVD

piayer,

Note: For an exD anation of Comoonent VlCteo,see your DVD player's owner's manual.

_DPlayerRearP_

Audio Cable

V'KleoCable

W R_rP_el

Rear Panel

Connecting a Digital TV Set-Top Box

Connect the Y, Pb, and Pr video outputs of' the set top box to their corresponding inputs on

the TV_Next, connect the Left and Right audio from the set top box to the corresponding

L and R terminaIs on the TM (The connections for a typical set top box are shown below.)

Set Top Box Rear Panel

TV Rear Panel

AudioCable

When switching to the DTV mode, either dg0p or 1080i format is automatically selected

according to the input signal.

Notes:

_rldeo Cable

DVD menu mode selection Intended for standard interlaced source material at 480i such as

a DVD Player (Non Progressive Scan).

DTV menu mode selection Intended for 480p or 1080i source material. Use this menu

option fur a Progressive Scan DVD Player that outputs 480p

(refer to page 3.17).

When a signal is connected to the DTV/DVD Component Video input, the external input select menu (On Screen Display) will show both DVD and DTV as "connected".

When a DTV (or DVD) signal is connected to the DTV/DVD Component Video Input and at the same time DVD (or DTV) is selected as the external input, the picture will show a dou ble or skewed image. Tel resolve this problem, please select DTV (or DVD) as the external

input on the select menu (On Screen Display).

(]]]'kPlll r\_o: INs],,] [,\]lO 2,7

INSTALLATION ]

Connecting a Surround Speakers

Connects to a rear-surround

Surround Left, SurrQund Right

W Rear Panel

_Jrmundspem'A 8_Jsp_rB

Connecting a Speakers (Variable Audio Output)

The °VARIABLEAUDIO OUT terminals cannot be usedfor

external soeakers. Youmust nOOKmere up to an amo(if(en,

TV Rear Panel

When an auo(o amotifier is connected to the" VARIABLE AUDIOOUT" terminals

Decrease the _aln IVOlumetOl

me auo(o amolifier, and adjust me volume level with the vol- ume con[romon the TV,

(See page4.141

2.8 ( ,,,.,.,.,,,, iNs].%_]AH(3N

+ 45 hidden pages