Samsung TNU-4041T, TNU-4051T User Manual
THERMAL
POSITIONING CAMERA
User Manual
TNU-4041T
TNU-4051T
Thermal Positioning Camera
User Manual
Copyright
Hanwha Techwin
©2018
Tra dema rk
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
Co., Ltd. All r ights reser ved.
Hanwha Techwin
reserves the
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated
from 24 V AC(50 or 60 Hz) min.6 A.
16. If you use excessive force when installing the product, the camera may be damaged and malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.
17. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As
edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or
near the kitchen table.
This may cause damage to the product.
18. When installing the product, be careful not to allow the surface of the product to be stained with chemical
substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.
19. If you install/disassemble the product in a manner that has not been recommended, the production functions/
performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
20. Installing or using the product in water can cause serious damage to the product.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER
OPENINGS ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with
the installation instructions.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
: TO REDUCE THE RISK OF ELECTRIC SHOCK.
CAUTION
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
●● OVERVIEW
English _3
overview
Class construction
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a
protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your
location.
When used outside of the U.S., it may be used HAR code with fittings of an approved agency
is employed.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION
IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE
INCORRECT.
METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
The CVBS out terminal of the product is provided for easier installation, and is not recommended
for monitoring purposes.
Please use the input power with just one camera and other devices must not be connected.
Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As
such, associated Ethernet wiring shall be limited to inside the building.
Please read the following recommended safety precautions carefully.
yDo not place this apparatus on an uneven surface.
yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or
heavy cold area.
yDo not place this apparatus near conductive material.
yDo not attempt to service this apparatus yourself.
yDo not place a glass of water on the product.
yDo not install near any magnetic sources.
yDo not block any ventilation openings.
yDo not place heavy items on the product.
yPlease wear protective gloves when installing/removing the camera.
The high temperature of the product surface may cause a burn.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
yReference : In case of providing information for helping of product’s usages
yNotice : If there’s any possibility to occur any damages for the goods and human caused by not
following the instruction
Please read this manual for the safety before using of goods and keep it in the safe place.
4_ overview
CONTENTS
OVERVIEW
3
INSTALLATION & CONNECTION
9
NETWORK CONNECTION AND SETUP
15
3 Important Safety Instructions
6 Product Features
6 Recommended PC Specifications
6 Recomended Micro SD/SDHC/SDXC Memory
Card Specifications
6 NAS recommended specs
7 What’s Included
8 At a Glance
9 Installation
10 Inserting/Removing a Micro SD Memory Card
11 Memory Card Information (Not Included)
12 Connecting with other Device
15 Connecting the Camera Directly to Local
Area Networking
15 Connecting the Camera Directly to a DHCP
Based DSL/Cable Modem
16 Connecting the Camera Directly to a PPPoE
Modem
16 Connecting the Camera to a Broadband
Router with the PPPoE/Cable Modem
17 Buttons used in IP Installer
17 Static IP Setup
19 Dynamic IP Setup
19 Port Range Forward (Port Mapping) Setup
20 Connecting to the Camera from a Shared
Local PC
20 Connecting to the Camera from a Remote PC
via the Internet
WEB VIEWER
21
APPENDIX
23
21 Connecting to the Camera
21 Password setting
22 Login
22 Plug-in support specifications for each
browser
22 Installing WebViewer Plugin
22 Using a Plug-in Free Webviewer
23 Specification
25 Product Overview
26 Troubleshooting
27 Open Source Announcement
●● OVERVIEW
English _5
overview
PRODUCT FEATURES
•Dustproof/Waterproof (IP66)
The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing it to
rain.
•Temperature change detection
An event is generated when the temperature value of the camera input image is analyzed and is larger or smaller
than the threshold value.
•Supports VGA pixel resolution videos
VGA-resolution (640x480 pixels) thermal camera: The thermal camera is a device that displays the temperature
distribution in a VGA-resolution (640X480) thermal image by sensing the surface temperature of the object in a
noncontact manner.
•Multi-Streaming
This network camera can display videos in different resolutions and qualities simultaneously using different
CODECs.
•Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
•Alarm
When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server, saved in a
Micro SD card or NAS, or a signal is sent to the alert output terminal.
•Motion Detection
Detects motion from the camera’s video input.
•Audio Detection
Detects sound louder than a certain level specified by user.
•Auto Detection of Disconnected Network
Detects network disconnection before triggering an event.
•Shock Detection
An alarm is generated when a shock is applied.
•IVA (Intelligent Video Analysis) function
Detects a motion or situation that meets the configured event rules.
•Sound source classification
Detects a sound source specified by the user.
•ONVIF Compliance
This product supports ONVIF Profile S&G.
For more information, refer to www.onvif.org.
RECOMMENDED PC SPECIFICATIONS
•CPU : Intel(R) Core(TM) i7 3.4 GHz or higher
•RAM : 8G or higher
•Supported OS : Windows 7, 8.1, 10, Mac OS X 10.10, 10.11, 10.12
•Webviewer
Recommended browser: Google Chrome 63
Supported browsers: IE11, MS Edge 41, Mozilla Firefox 57(Windows 64bit only), Apple Safari 11 (Mac OS X only)
RECOMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS
•Recommended capacity : 16GB to 256GB (MLC type)
•The following types of memory cards from the following manufacturers are recommended for this camera.
-Manufacturer : SanDisk, Transcend
-Product family : High endurance
NAS RECOMMENDED SPECS
•Recommended capacity : 200GB or higher is recommended.
•Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.
•For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
Recommended products Available sizes
QNAP NAS A maximum of 16 cameras can access simultaneously.
Synology NAS A maximum of 16 cameras can access simultaneously.
`
If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.
J
6_ overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
(As for each sales country, accessories are not the same.)
Appearance Item Name Quantity Description
Camera body
1
Appearance Item Name Quantity Description
Wall Mount Bracket (not included)
Wall Mount Bracket 1 Used when installing the camera on a wall
●● OVERVIEW
Instructions and installation
software DVD
Quick Guide
(Optional)
Warranty card
(Optional)
Sunshield
Sunshield Hold
Star-Shape wrench
RJ45 waterproof accessory
1
1
1
-
-
-
Wrench bolts(M5 X 20) / flat washers 3/3 for connecting the main body and bracket
Bolts(M3 x 8) 8 for connecting the cable wiring cover
O-ring 1 for connecting the main body and bracket
1
1
1
1
It protects the camera from the direct sunlight.
It fixes the sunshield with the camera.
For attaching the memory slot cover
Used to install in humid places
English _7
overview
AT A GLANCE
Appearance
a
b
c
d
Item
Cables
e
a
b
c
d
e
Item Description
a
b
c
d
e
8_ overview
Sunshield
Camera
Main body
Base housing
Micro SD card slot
Alarm cable Alarm I/O cable. (Black/Brown/Red/Yellow/Orange)
a
Audio cable Audio I/O cable.
b
Ethernet Connects the Ethernet cable.
c
Video output cable Outputs the video.
d
e
Power cable
Cables for the camera power .
(Brown/Blue)
installation & connection
INSTALLATION
Precautions before installation
Ensure you read out the following instructions before installing the camera:
•Install the system based on the following directions. If you want to install using a different method, you should
confirm the safety recommendations by making a request to the manufacturer in advance.
•The gross weight of the system is 11.7 kg. A pair of anti-slip gloves must be worn. When you lift your device, do
not grab the camera but the body.
•It must be installed on the area (ceiling or wall) that can withstand 4 times the weight of the camera including
the installation bracket.
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
Install the device on the floor
Install the pedestal on the floor.
1.
M10X30 anchor bolts
(not provided)
Washers
(not provided)
Optional Accessories for Installation
For your easier installation, you can purchase appropriate optional accessories available.
`Mounting on wall using bracket
Connect the side of the bracket to the wall using
1.
4 anchor bolts (not supplied).
We recommend using M10X30 anchor bolts or better to install the camera on concrete.
`
J
Use screws that can withstand more than four times the weight of the equipment.
`
Assemble the main body and bracket using 3 Wrench bolts.
2.
Washers
(not provided)
Anchor bolts
(not provided)
●● INSTALLATION & CONNECTION
We recommend using M10X30 anchor bolts or better to install the camera on concrete.
`
J
Use screws that can withstand more than four times the weight of the equipment.
`
O-ring
Flat washer
M5 x 20 bolts
English _9
installation & connection
After organizing the cables as shown, assemble the cover.
3.
M3X8 bolts
INSERTING/REMOVING A MICRO SD MEMORY CARD
Disconnect the power cable from the camera before inserting the Micro SD memory card.
`
J
Do not insert the Micro SD memory card while it’s upside down by force.
`
Otherwise, it may damage the Micro SD memory card.
When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
`
Separating the Micro SD card insert cover
Use the star key to remove the Micro SD card insert cover.
Micro SD Card Insert Cover
Inserting a Micro SD Memory Card
Insert a Micro SD card in the arrow direction shown in the figure.
10_ installation & connection
Removing a Micro SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card
from the slot.
MEMORY CARD INFORMATION NOT INCLUDED
What is a memory card?
The memory card is an external data storage device that has been developed to offer an entirely new way to
record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports Micro SD/SDHC/SDXC memory cards.
You may, however, experience compatibility issues depending on the model and make of the memory card.
The following types of memory cards from the following manufacturers are recommended for this camera.
-Manufacturer : SanDisk, Transcend
-Product family : High endurance
It is recommended to use a 16GB to 256GB (MLC type) memory card for this camera.
Playback performance can be affected depending on the speed of memory card.
Contacts
●● INSTALLATION & CONNECTION
Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released.
`
J
Before removing the Micro SD memory card, in <Storage>, set the device to <Off> and press the [Apply] button and turn the
`
camera off.
If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or damaged.
`
Micro SD/SDHC/SDXC
English _11
installation & connection
CONNECTING WITH OTHER DEVICE
Connecting to Audio Input/Output
Alarm cable
Audio I/O cable
Ethernet
Video output cable
Power cable
Speaker
Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifier that
1.
the microphone is connected to.
Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
2.
Check the specifications for audio input.
3.
•Audio Codec : G.711 PCM. μ-law 64kbps 8kHz sampling
•Full duplex Audio
•Audio in : Used for mono signal line input (Max.2.4 Vpp)
•Audio out : Used for mono signal line output (Max.2.4 Vpp)
•Line out impedance : 600Ω
Alarm I/O Wiring Diagram
ALARM IN
ALARM OUT_NC
ALARM OUT_NO
(5 mA sink)
(30 V DC, 1 A/125 V AC, 0.3 A)
12_ installation & connection
Speaker
AUDIO IN
AUDIO OUT
Amp
Microphone
Amp
Network
Microphone
Microphone
ALARM OUT COM
PC
GND
Loading...