Samsung TNO-6010M User Manual

NETWORK CAMERA

User Manual

TNO-6010M

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from PoE (48V), 0.17A.

16. This product is intended to be supplied by isolation power.

17. If you use excessive force when installing the product, the camera may be damaged and malfunction.

If you forcibly install the product using non-compliant tools, the product may be damaged.

18. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

19. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

20. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

21. Installing or using the product in water can cause serious damage to the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

●● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION

IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

4_ overview

CONTENTS

OVERVIEW

INSTALLATION & CONNECTION

NETWORK CONNECTION AND

SETUP

3 Important Safety Instructions 6 Product Features 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

6 NAS recommended specs 7 What’s Included 7 At a Glance

11 Installation 14 Inserting/Removing a Micro SD Memory

Card

15 Connecting with other Device

16 Connecting the Camera Directly to Local

Area Networking

16 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

17 Connecting the Camera Directly to a

PPPoE Modem

17 Connecting the Camera to a Broadband

Router with the PPPoE/Cable Modem

18 Using Device Manager 18 Automatically searching camera 18 Configuring IP address 19 Manually registering camera 19 Automatically configuring IP 20 Port Range Forward (Port Mapping) Setup 21 Connecting to the Camera from a Shared

Local PC

21 Connecting to the Camera from a Remote

PC via the Internet

WEB VIEWER

APPENDIX

22 Connecting to the Camera 23 Password setting 23 Login 23 Camera Web Viewer Setup

24 Specification 25 Product Overview 26 Troubleshooting 27 Open Source Announcement

●● OVERVIEW

English _5

overview

PRODUCT FEATURES

• Surveillance camera for car Enables monitoring of a running train or vehicle without camera shake.

• Dustproof/waterproof (IP66) The dustproof/waterproof design protects the product from rain and dust when installed outdoors.

• Supports 2M pixel resolution videos

• Multi-Streaming This network camera can display videos in different resolutions and qualities simultaneously using different

CODECs.

• Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment.

• Alarm When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server,

saved in a Micro SD card or NAS.

• Tampering Detection Detects tempering attempts on video monitoring.

• Defocus detection function Detects the defocus phenomenon of the camera lens.

• Motion Detection Detects motion from the camera’s video input.

• Smart Codec Adaptively applies codecs for a portion of the camera’s field of view to improve the quality of such area specified

by user.

• Auto Detection of Disconnected Network Detects network disconnection before triggering an event.

• Fog detection Detects fog that is heavier than the detection level.

• Face Detection Detects faces in the specified area from the camera’s video input.

• IVA (Intelligent Video Analysis) function Detects a motion or situation that meets the configured event rules.

• ONVIF Compliance This product supports ONVIF Profile S/G/T.

For more information, refer to www.onvif.org.

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• RAM : 8G or higher

• Supported OS : Windows, Mac OS X

• Plug-in free web viewer Supported web browsers : Google Chrome, MS Edge, Mozilla Firefox(Windows 64bit only), Apple Safari (Mac OS X only)

• Plug-in Webviewer Supported web browsers : MS Explorer, Apple Safari (Mac OS X only)



Refer to the appendix for detailed OS and browser version information.

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB to 256GB (MLC type)

• The following types of memory cards from the following manufacturers are recommended for this camera.

- Manufacturer : SanDisk, Transcend

- Product family : High endurance

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description

Camera 1

Quick Guide 1

Warranty card 1

AT A GLANCE

Appearance

●● OVERVIEW

L Wrench 1

Tapping Screw (M5xL30) 3 Used for fixing the bracket wall mount to the wall or ceiling.

Plastic Anchor (Ø6xL30) 3

Label Template 1 Used when installing the camera.

Bracket wall mount 1 Used for installing the camera on the ceiling or wall.

Set Screw 2 Used for fastening the camera to the Bracket wall mount.

Cable for the testing monitor 1

Hood 1

Used for opening/closing the Micro SD Card cover or moving/

fastening the bracket part.

For fixing a screw, Inserted in a hole (reinforced anchoring

force)

Used to test the camera connection to a portable display

device.

M12 Female connector

cable

2nd Tilting Joint

Sliding Body

1st Tilting Joint

Rubber Hood

Item Description

Connect to the M12 Male connector cable for power supply and network connections.

English _7

overview

Disassembling the interface cover

Use the hexa wrench and loosen the two screws shown in the figure below by turning 4 to 5 times to open the cover.

The location and function of the main interface part is described in the figure on the right. After completing the setup and closing the cover, assemble the cover to fit the bump that guides the assembly orientation while making sure that the orange wire string does not interfere with the cover, and then fasten the two screws.

• The camera supports IP66 specification. Please tighten the screws firmly to avoid water leak and dust inflow.

Inside

MICRO USB Port

Bump that guides the cover’s assembly

orientation

Reset Button

Test Monitor Out

Micro SD Memory Card

Compartment

USB RESET

VIDEO

Item Description

Port to connect the Wi-Fi dongle. You can check the installation video through the applications installed in the smartphone. (for installation) Refer to “Connect to WiFi dongle” on page 15.

WiFi dongle and OTG adapter are sold separately.

Resets the camera settings to the default. Press and hold for about 5 seconds to reboot the system.

Output port for test monitoring the video output. Use the test monitor cable to connect to a mobile display and check the test video.

Compartment for the Micro SD memory card.

If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

a b

8_ overview

Bracket - Tilting

You can loosen the screws in the two joints of the bracket instruction part by about two turns to adjust the tilting angle of the camera. The following is the moving angle supported by the two tilting joints:

• 1st tilting, 0 to 120 degree movement

• 2nd tilting, -30 to 90 degree movement

- Shipment default is 0 degree for the 1st & 2nd tilting angles

- After adjusting the tilting angle appropriately, fasten the two screws, and make sure that they are firmly fastened.

Wall mounting example

●● OVERVIEW

Shipment default is 0˚

1st tilting angle: 0 to 120˚ 2nd tilting angle: -30 to 90˚

Bracket - Rotate

When installing on the wall surface, completely loosen the screws of the two joints from the bracket instruction part, and rotate the bracket 90 or -90 degrees to fasten the screw again.

• Shipment default is 0 degree of rotate angle

• After adjusting the rotate angle appropriately, fasten the two screws, and make sure that they are firmly fastened.

0˚

90˚

-90˚

Two screw holes for wall mounting

Bracket - Panning

Before completely fastening the set screws (including the opposite side of the direction arrow in the below figure) of the two joints to the bracket instruction part, panning of 360 degrees is supported.

• After adjusting the panning angle appropriately, fasten the two screws, and make sure that they are firmly fastened. Since the two set screws are covered with a hardening agent, it would require much stronger force to remove the screw after fastening it due to the agent's hardening property. To easily remove the screws, use a soldering iron to partially heat up the screws (about 450˚F) and remove them.

English _9

overview

Bracket - Panning for Horizontal Calibration of Video

Depending on the tilt of the wall surface or celling for installation, the horizontal level of the video output may be inclined after installation.

In this case, the video horizontal level can be calibrated by loosening the instruction part screw by about a half turn, rotating the camera part to level it, and fastening the two screws. The supported moving angle is as follows:

• Angle allowed for horizontal calibration: -20 to 20 degrees

- Shipment default is 0 degree

- After adjusting the panning angle appropriately, fasten the two screws, and make sure that they are firmly fastened.

- The warranty does not cover any paint abrasion or peel on the part’s external surface caused by repetitive panning movement for horizontal calibration.

Panning for horizontal calibration of video: -20 to 20˚

Shipment default is 0 degree

Bracket - Sliding

The bracket length can be adjusted by loosening the two screws of the instruction part by about one turn. After adjusting it to an appropriate length, please re-fasten the screw. The following operational stroke is supported:

• Operational stroke: 0 to 63 mm

- Shipment default is 0 mm

- After adjusting the length appropriately, fasten the two screws, and make sure that they are firmly fastened.

- The warranty does not cover any paint abrasion or peel on the corresponding part’s external surface caused by repetitive sliding movement.

Shipment default is 0mm

Available stroke 63 mm

10_ overview

installation & connection

INSTALLATION

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• When installing on a ceiling, desired spot must be capable of supporting at least 5 times of the camera’s weight.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

• This camera is a waterproof product that meets IP66 standards. However, if the M12 standard connector and cable are not used, the jack part will not be waterproof. It is recommended to use an M12 standard external cable when installing this product.

• When installing the camera on the outside of the vehicle, be sure to install it on a flat surface. If the mounting surface is curved, it may not properly adhere to the rubber, and may not be waterproofed.

• Depending on the shape and tilt of the vehicle windshield in front of the camera, the night conditions and specific camera installation angle could cause reflection of external lights. If this kind of problem occurs, readjust the camera installation angle to avoid such a problem.

• Since this product is equipped with a waterproof ventilation system, avoid installing it in a place that exhibits a sudden artificial change in temperature.

• To prevent condensation, this product has a separate damp-proof component and heater attached to it. Due to the nature of the product, dews may be formed after initially energizing the product, but they will disappear within an hour. If they still remain or reappear during the use, manually turn on the heater. Refer to “Troubleshooting”. (Page 26)

Remove protective film

As you can see in the figure, a protective film is attached to the front side of the camera window. If you see any fingerprints or dust in the window, please use a soft cloth such as fine fiber to clean it off. Since the window is made of Polycarbonate (PC), you are allowed to use a cleaning agent which doesn’t affect the material.

Hood assembly

Align the hood with the bump inside the hood and instruction groove of the camera part to assemble. As described in the figure, it is much easier to align if you keep checking the positions of the bump and the

corresponding groove from the front when assembling.

• Remove the protective film from the window surface before assembling the hood. After it is removed, avoid contamination or scratch on the window surface.

●● INSTALLATION & CONNECTION

English _11

installation & connection

How to install

TNO-6010M camera is to be installed inside a vehicle for recording outside scene from the front windshield. To minimize any negative effect on the video caused by internal light sources in vehicles near the camera,

we recommend you to install the hood on the camera as close to the windshield as possible. (Camera view could be blocked if the hood is deformed depending on the installation location.)

For optimal installation, the following is supported for the bracket part: 1st tilting, 0 to 120 degrees & 2nd tilting -30 to 90 degrees / Rotate 0 degree or 90 (-90) degrees / Panning 360 degrees / Panning for horizontal calibration of video -20 to 20 degrees / Sliding 0 to 63 mm stroke movement.

• The factory default is as follows: 1st & 2nd tiling 0 degree / rotate 0 degree / panning for horizontal calibration of video 0 degree / Sliding 0 mm. (* See the exterior diagram in the back.)

Ceiling

2nd tilting: -30 to 90˚

Sliding: 63 mm

Rotate: 0 or 90 (-90) degrees

1st tilting: 0 to 120˚

Panning for horizontal calibration of video: -20 to 20˚

Panning: 0 to 360 degrees

After considering the celling or wall surface for camera installation, required shooting range, etc., attach the camera to the hood. Consider the appropriate orientation, bending, and length of the bracket in advance, and roughly mark the installation location of the bracket wall mount on the celling or wall surface.

Then, take off the installation guide part (Ø80mm(3.15”)) from the label template and attach it to the wall surface or ceiling marked for the installation of the bracket wall mount.

• Use a drill to make three holes for the anchor and one hole for the cable, and remove the attached installation guide part.

• Insert the anchors in the three holes for the anchors. (To insert them easily, lightly hammer the anchors.)

• Align the three holes for screws created in the bracket wall mount with the three installed holes for anchors, and use the appropriate driver or power tool to fasten the tapping screws (‘+’).

• Pick up the corresponding cable for M12 for connection with the camera, and pull it out or push it into the center hole of the bracket wall mount.

12_ installation & connection

+ 26 hidden pages