Page 1
INSTALLATION AND OPERATION MANUAL TER-F01 SERIES
TER-F01 Series
10/100 MBPS ETHERNET REPEATER WITH 60 W PASSTHROUGH POE
This manual serves the following
Model Names:
TER-F01
TER- F01PD
The TER-F01 series is an Ethernet repeater supporting up to 60 watts of Pass-through
PoE, providing a simple and cost-effective way to extend Ethernet signals beyond
the standard Ethernet 328 foot (100 meter) limit. The TER-F01 can be used to
double the distance to 656 feet (200 meters) or multiple units can be combined in
series with each unit providing an additional 328 feet (100 meters). The TER-F01 is
powered by pass-through PoE from a PoE switch or midspan injector, requiring no
local power. Low power consumption ensures that maximum power is made
available to the remote PD device.
The standard configuration passes through the PoE to the next device, or as a PD
model, which acts as the final PoE unit in the chain and does not pass through the PoE.
INS_TER-F01[PD] 08/12/19 PAGE 1
Page 2
INSTALLATION AND OPERATION MANUAL TER-F01 SERIES
3.2 cm
8.4 cm
FIGURE 1 – TER-F01[PD] EXTENDER
ETHERNET ETHERNET
Power: Supplied by PSE
Note: Ports are universal, and either can be used as in or out.
FIGURE 3 – INDICATING LEDS
COPPER
GREEN
YELLOW
Solid – No Activity
Blinking – Ac tivity
Highest Data Rate
(100Mb)
Power Consumption: <1 W
FIGURE 4 - DIMENSIONS
Dimensions are for a tube module
[3.3 in]
3.2 cm
[1.25 in]
INSTALLATION CONSIDERATIONS
The TER-F01[PD] is supplied as a 3.3 × 1.25 × 1.25 in (8.4 × 3.2 × 3.2 cm) tube
module.
Units should be installed in dry locations protected from extremes of temperature
and humidity.
WARNING: Unit is to be used with a Listed Class 2 power supply.
[1.25 in]
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is not
compromised.
INS_TER-F01[PD] 08/12/19 PAGE 2
Page 3
A
INSTALLATION AND OPERATION MANUAL TER-F01 SERIES
SPECIFICATIONS
Ethernet
Data Interface 10/100BaseT(X) Ethernet
IEEE 802.3 Compliant
Full Duplex or Half Duplex Electrical Ports
Standards IEEE: 802.3af PoE, 802.3at PoE+
RFC: 768 UDP, 2068 HTTP, 793 TCP, 791 IP, 1783
TFTP, 894 IP over Ethernet, 2544 TCP/IP Packet
Transmission
Transmission Distances
1
See char t below
Connectors
Ethernet 2 × RJ-45
Mechanical
Indicating LEDs Ethernet Link and Activity
Circuit Board Meets IPC Standard
TER-F01[/PD] Size 3.3 × 1.25 × 1.25 in (8.4 × 3.2 × 3.2 cm)
Shipping Weight <1 lbs./0.5 kg
Environmental
MTBF >100,000 hours
Operating Temp – 40˚ C to +75˚ C
Storage Temp – 40˚ C to +80˚ C
Relative Humidity 0% to 95% (non-condensing)²
Power
Pass-Through Mode Operates on PoE Power
Power Consumption < 1 W
Protection High Impedance PoE Pass-Through with Start-up
Voltage Detection and Current Limiting
MAXIMUM TRANSMISSION DISTANCES
1
GENCY COMPLIANCE
Maximum Range & Repeaters for PoE Power (Watts)
PoE Source
15 W PoE Switch
30 W PoE+ Switch
35 W PoE+ Injector
[1] Distance figures are based on 48V PSE PoE power source for PoE switches, 50V PSE PoE power source for PoE+ switches and 56V PSE PoE
power source for the injector as detailed in the table. Distance figures are obtained using in-house testing mirroring installations. Factors
such as cable quality, the number of connectors and splices in the cable run, the use of PoE, and environmental conditions encountered
within the installation might affect the actual transmission distance and should be taken into consideration.
[3] Non-PoE applications; using a TER-F01PD model at the end of the chain
[4] Extension is not needed/possible at this PoE power level with this particular PoE power source at the distance listed
No PoE³ 5 W 10 W 15W 20 W 25 W
2,625 ft
800 m
(Using 7 TER-F01)
2,625 ft
800 m
(Using 7 TER-F01)
3,773 ft
1,150 m
(Using 11 TER-F01)
1,476 ft
450 m
(Using 4 TER-F01)
1,969 ft
600 m
(Using 5 TER-F01)
2,625 ft
800 m
(Using 7 TER-F01)
984 ft
300 m
(Using 2 TER-F01)
1,316 ft
400 m
(Using 3 TER-F01)
1,804 ft
550 m
(Using 5 TER-F01)
328 ft4
100 m4
(No TER-F01)
984 ft
300 m
(Using 2 TER-F01)
1,316 ft
400 m
(Using 3 TER-F01)
4
N/A
656 ft
200 m
(Using 1 TER-F01)
984 ft
300 m
(Using 2 TER-F01)
4
N/A
328 ft4
100 m4
(No TER-F01)
656 ft
200 m
(Using 1 TER-F01)
INS_TER-F01[PD] 08/12/19 PAGE 3
Page 4
INSTALLATION AND OPERATION MANUAL TER-F01 SERIES
FIGURE 2 – TER-F01[PD] Typical Applications
Please see the Maximum Transmission Distances Table.
PoE Pass-Through Mode to PoE Device
10 or 100 Mbps
PoE Switch
Power
328 ft (100 m)
PoE PoE PoE
PoE Pass-Through Mode to Non-PoE Device
10 or 100 Mbps
PoE Switch
Power
PoE
High-Power PoE Pass-Through Mode to PoE+ Device
Extend the Distance with Repeaters
to suit your application.
Extend the Distance with Repeaters
to suit your application.
PoE
Legend
Cat-5 Cable
PoE Power
328 ft (100 m)
TER-F01TER-F01
328 ft (100 m)328 ft (100 m)
TER-F01PDTER-F01
10 or 100 Mbps
PoE Camera
Switch
10 or 100 Mbps
Switch
PoE Injector
Power
328 ft (100 m)328 ft (100 m)
PoE+ PoE+
TER-F01
PoE+ Camera
INS_TER-F01[PD] 08/12/19 PAGE 4
Loading...