Samsung SYNCMASTER 94B User Manual

SAMTRON 94B
Install drivers
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Prohibited Important to read and understand at all times
Do not disassemble Disconnect the plug from the outlet
Do not touch Grounding to prevent an electric shock

Power

When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
This may cause an electric shock or fire.
z
Do not pull the plug out by the wire nor touch the plug with wet hands.
This may cause an electric shock or fire.
z
Use only a properly grounded plug and receptacle.
An improper ground may cause electric shock or equipment damage.
z
Insert the power plug firmly so that it does not come loose.
A bad connection may cause fire.
z
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.
This may cause an electric shock or fire.
z
Do not connect too many extension cords or plugs to an outlet.

Installation

z This may cause fire.
Be sure to contact an authorized service center, when installing your monitor in a location with the heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc.
Failure to do so may cause a serious damage to your monitor.
Put your monitor in a location with low humidity and a minimum of dust.
Failure to do so may cause an electric shock or fire inside the monitor.
z
Do not drop the monitor when moving it.
z This may cause damage to the product or human body.
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.
Dropping the product may cause damage to the product or personal injury.
z
Do not place the product on an unstable or small surface area.
Place the product on an even, stable surface, as the product may fall and
z
cause harm to someone walking by, specifically children.
Do not place the product on the floor.
Someone, specifically children could trip over it.
z
Keep any flammable objects such as candles, insecticides or cigarettes away from the product.
Otherwise, this may cause a fire.
z
Keep any heating devices away from the power cable.
A melted coating may lead to electric shock or fire.
z
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.
Any increase in internal temperature may cause fire.
z
Set down the monitor carefully.
The monitor could be damaged or broken.
z
Do not place the monitor face down.
The TFT-LCD surface may be damaged.
z
Installing a wall bracket must be done by a qualified professional.

Clean

z Installation by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
z
When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inch ) for ventilation purposes.
Poor ventilation may cause an increase in the internal temperature of the
z
product, resulting in a shortened component life and degraded performance.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor.
This may cause damage, electric shock or fire.
z
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.
A dirty connector may cause an electric shock or fire.
z
Make sure to unplug the power cord before cleaning the product.
Otherwise, this may cause electric shock or fire.
z
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide,
z
air freshener, lubricant or detergent.
Others
Contact the Service Center or Customer Center for interior cleaning once a year.
Keep the product's interior clean. Dust which has accumulated in the interior
z
over an extended period of time may cause malfunction or fire.
Do not remove cover (or back).
This may cause an electric shock or fire.
z
Refer servicing to qualified service personnel.
z
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact
an authorized dealer or service.
This may cause an electric shock or fire.
z
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.
This may cause malfunction, an electric shock or fire.
z
Especially avoid operating the monitor near water or outdoors where it could be
z
exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center .
z The monitor may malfunction, causing an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.
Failure to do so may cause an electric shock or fire.
z
Do not try to move the monitor by pulling only the wire or the signal cable.
This may cause a breakdown, electric shock or fire due to damage to the
z
cable.
Do not move the monitor right or left by pulling only the wire or the signal cable.
This may cause a breakdown, electric shock or fire due to damage to the
z
cable.
Do not cover the vents on the monitor cabinet.
Bad ventilation may cause a breakdown or fire.
z
Do not place water containers, chemical products or small metal objects on the monitor.
This may cause malfunction, an electric shock or fire.
z z If a foreign substance enters the monitor, unplug the power cord and contact
the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances.
This may cause an explosion or fire.
z
Never insert anything metallic into the monitor openings.
This may cause an electric shock, fire or injury.
z
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports.
It may cause a fire or an electric shock. If an alien substances or water flows
z
into the product, turn the product off, unplug the power connector from the wall outlet and contact service center.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
Change the mode to energy save or set a screensaver to moving picture when
z
you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model.
z Inappropriate resolution may cause undesirable picture quality.
19 inch (48 cm) - 1280 X 1024
Watching the monitor continuously at a too close angle may result in eyesight damage.
To ease eye strain, take at least a five-minute break after every hour of using the monitor
.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
Dropping the product may cause damage to the product or personal injury.
z
Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor.
z Failure to disconnect cables may damage it and lead to fire or an electric
shock.
Place the product out of children’s reach, as they could damage it by hanging onto it.
A falling product could cause physical damage even death.
z
When not using the product for an extended time period, keep the product unplugged.
z Otherwise, this may cause heat emission from the accumulated dirt or
degraded insulation, leading to electric shock or fire.
Do not place children’s favorite objects (or anything else that may be tempting) on the product.
Children may try to climb on the product to retrieve an object. The product
z
could fall, causing physical damage or even death.
r
r
r
)
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local deale
to buy optional items.

Unpacking

Monitor
Manual
Quick Setup Guide
Monito
Warranty Card
(Not available in all locations)
User's Guide,
Monitor Drive
Cable
D-Sub Cable Power Cord DVI Cable(option

Front

1. MEUN button [ ]
2. MagicBright button []
2,4. Adjust buttons [ ]
3. Power button [ ] / Power indicator
4. Brightness button [ ]
5. Enter button [ ]/ SOURCE button
See PowerSaver described in the manual for further information regarding power saving functions.
Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu.
MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers, the pre­configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.
2) Text
For documentations or works involving heavy text.
3) Internet
For working with a mixture of images such as text and graphics.
4) Entertain
For watching motion pictures such as a DVD or VCD.
>>Click here to see an animation clip
Adjust items in the menu.
Use this button for turn the monitor on and off./ This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
When OSD is not on the screen, push the button to adjust brightness.
Activates a highlighted menu item. / Push the ' (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable.
: Normal brightness
: Medium brightness
: High brightness
SOURCE
', then selects the video signal while the OSD is off.
g

Rear

For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
(The configuration at the back of the monitor may vary from product to product.)
1. POWER port
2. DVI IN port
3. RGB IN port
4. Kensington Lock
See Connecting the Monitor for further information regarding cable connections.
Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI IN port on the back of your monitor.
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately. )
For usin
a locking device, contact where you purchase it.
1.
2-1.
2-2.
2-3.
2-4.
3.
Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.
Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI port on the back of your monitor.
Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-sub connection cable.
In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.
Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Attaching a Base
[ RGB IN ]
[ DVI IN ]
A
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad (Sold separately)
. Turn off your monitor and unplug its power cord.
1
. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
2
. Remove four screws and then remove the stand from the LCD monitor.
3
lign the mounting interface pad with the holes in the rear cover mounting Pad and secure it with four
.
4
screws that came with the arm-type base, wall mount hanger or other base.
Internet web site : http://www.samtron.com/
z
Windows XP/2000
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
1. Insert CD into the CD-ROM drive.
2. Click
"Windows XP/2000 Driver"
3. Choose your monitor model in the model list, then click the
button.
"OK"
4. If you can see following message window, then click the click
"OK"
button.
"Continue Anyway"
button. Then
/
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samtron Monitor homepage
http://www.samtron.com
5. Monitor driver installation is completed.
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
z Internet web site : http://www.samtron.com/
Microsoft® Windows® XP Operating System
.
Windows XP | Windows 2000 | Windows NT | Linux
1. Insert CD into the CD-ROM driver.
2. Click "
Start
" —> "
Control Panel
" then click the "
3. Click "
" icon and choose the "
Display
Settings
Appearance and Themes
" Icon.
" tab then click "
Advanced..
".
4. Click the "
Properties
" button on the "
Monitor
" tab and select "
Driver
" tab.
5. Click "
Update Driver..
" and select "
Install from a list or..
" then click "
Next
" button.
6. Select "
Don't search ,I will..
7. Click the " and click the "
" then click "
" and then click "
Next
Have disk
".
" button then choose A:(D:\Driver) and choose your monitor model in the model list
Browse
Next
" button.
8. If you can see following message window, then click the
button.
"OK"
"Continue Anyway"
button. Then click
This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samtron Monitor homepage.
http://www.samtron.com/
9. Click the "
" button then click "OK" button continually.
Close
10. Monitor driver installation is completed.
Microsoft
®
Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "
2. Click the "
Browse
" button on the "
Insert disk
" window.
File Needed
" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "
2. Double click the "
3. Choose the "
4. Choose "
Start
" , "
Setting
Settings
Monitor
" , "
Control Panel
" Icon.
Display
" tab and then click "
".
".
Advanced..
".
Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
5. Click "
6. Choose "
driver
7. Click the "
8. Click the "
9. Choose your monitor model and click the "
10. Click the "
" and then click on "
Driver
Update Driver..
" then click on the "Next" button.
Display a list of the known drivers for this device so that I can choose a specific
" then click "
Browse Open
Finish
" and then click "
Next
Have disk
" button then choose A:(D:\Driver).
" button, then click "OK" button.
Next
" button then the "
Close
" button.
".
" button then click "
Next
" button.
If you can see the " the "
" button then the "
Finish
Digital Signature Not Found
" button.
Close
" window then click the "
"button. And click
Yes
Microsoft
1. Click
2. In Display Registration Information window, click Settings Tab and then click
®
Windows® NT Operating System
Start, Settings, Control Panel
, and then double-click
Display
icon.
All Display Modes
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.
4. Click
button if you see the screen working normally after clicking
Apply
. If the screen is not
Test
normal, change to a different mode (lower mode of resolution, colors or frequency).
If there is no Mode at
All Display Modes
, select the level of resolution and vertical frequency
by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1. Press Enter at the first and the second screen after executing the X86Config file.
2. The third screen is for
setting your mouse
.
3. Set a mouse for your computer.
4. The next screen is for
selecting a keyboard
.
5. Set a Keyboard for your computer.
6. The next screen is for
7. First of all, set a
8. Set a
vertical frequency
9. Enter the
horizontal frequency
model name of your monitor
setting your monitor
for your monitor. (You can enter the frequency directly.)
.
for your monitor. (You can enter the frequency directly.)
. This information will not affect the actual execution of X-
Window.
10. You have
Execute
finished
X-Window after setting other requested hardware.
setting up your monitor.
.
Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
1.
This button allows you to adjust items in the menu.
2.
This button allows you to adjust items in the menu.
3.
Press this button to activate a highlighted menu item.
4.
AUTO
Menu Description
Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)
AUTO
To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
z If you change resolution in the control panel, auto function will be executed
automatically.
MagicBright
Menu Description
Then push the MagicBright button again to circle through available preconfigured
MagicBright
modes.
- four different modes(Custom/Text/Internet/Entertain)
Brightness
Menu Description
Brightness
Source
When OSD is not on the screen, push the button to adjust brightness.
Menu Description
Source
1. Picture
2. Color
3. Image
4. OSD
5. Setup
6. Information
Selects the Video signal while the OSD is off.
Brightness Contrast
Color Tone Color Control Gamma
Coarse Fine Sharpness H-Position V-Position
Language H-Position V-Position Transparency Display Time
Auto Source Image Reset Color Reset
Picture
Menu Description Play/Stop
You can use the on-screen menus to change the brightness
Brightness
according to personal preference.
Direct Access Feature
the button to adjust brightness.
: When OSD is not on the screen, push
Contrast
Color
You can use the on-screen menus to change the contrast according to personal preference.
Menu Description Play/Stop
Color Tone
The tone of the color can be changed and one of four modes
can be selected - Cool, normal, Warm and Custom.
Color Control
Gamma
Image
Adjusts individual R,G,B color balance.
Gamma correction changes the luminance of the colors with intermediate luminance.
Mode 1
z
Mode 2
z
Mode 3
z
Menu Description Play/Stop
Removes noise such as vertical stripes. Coarse adjustment may
Coarse
move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only)
Removes noise such as horizontal stripes. If the noise persists
Fine
even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only)
Sharpness
H-Position
V-Position
Changes the clearance of image.
Changes the horizontal position of the monitor's entire display. (Available in analog mode only)
Changes the vertical position of the monitor's entire display. (Available in analog mode only)
OSD
Menu Description Play/Stop
You can choose one of the seven languages.
Language
H-Position
V-Position
Transparency
Display Time
Setup
:The language chosen affects only the language of the
Note
OSD. It has no effect on any software running on the computer.
You can change the horizontal position where the OSD menu appears on your monitor.
You can change the vertical position where the OSD menu appears on your monitor.
Change the transparency of the background of the OSD.
The menu will be automatically turned if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Menu Description Play/Stop
Auto Source
Image Reset
Color Reset
Information
Select
Auto Source
signal source.
Image parameters are replaced with the factory default values.
Color parameters are replaced with the factory default values.
for the monitor to automatically select the
Menu Description
Information
Shows a video source, display mode on the OSD screen.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information
section or contact your dealer.

Symptom Check List Solutions

No images on the screen. I cannot turn on the monitor.
Is the power cord connected properly? Check the power cord connection and
Can you see the screen?
If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
"Check Signal Cable"
supply.
on
(When connecting D-Sub cable)
Check the signal cable connection.
(When connecting DVI cabel)
If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press source button to have the monitor double-check the input signal source.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes)
Note: If the initial screen (the login screen) does not appear, contact the
Service Center or your dealer.
Can you see
Mode","Recommended Mode 1280 x 1024 60Hz"
"Not Optimum
on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.
Adjust the maximum resolution and frequency that the monitor can handle properly.
If the display exceeds SXGA or 75Hz, a
"Not Optimum Mode","Recommended Mode 1280 x 1024 60Hz"
the display exceeds 85Hz, the display will work properly but the
Optimum Mode","Recommended Mode 1280 x 1024 60Hz"
appears for one minute and then disappears. Please change to the recommended
message is displayed. If
"Not
message
mode during this one-minute period. (The message is displayed again if the system is rebooted.)
The screen shows strange colors or just black and white.
The screen suddenly has become unbalanced.
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
Connected using the DVI cable? You may get a blank screen if you boot
Is the screen displaying only one color as if looking at the screen through a cellophane paper?
Have the screen colors become strange after running a program or due to a crash between applications?
Has the video card been set properly? Set the video card by referring to the
Have you changed the video card or the driver?
Have you adjusted the resolution or frequency to the monitor?
The monitor is in PowerSaver mode.
press a key on the keyboard to activate the monitor and restore the image on the screen.
the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system.
Check the signal cable connection.Make sure the video card is fully inserted in it's slot.
Reboot the computer.
video card manual.
Adjust screen image position and size using the OSD.
Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD.
The screen is out of focus or OSD cannot be adjusted.
LED is blinking but no images on the screen.
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the video cables are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 56Hz ~ 75Hz. (Do not exceed 75Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "
Have you adjusted the resolution or frequency on the monitor?
Is the frequency properly adjusted when checking the Display Timing on the menu?
Have the Windows colors been set properly?
Has the video card been set properly? Set the video card by referring to the
Have you installed the monitor driver? Install the monitor driver according to
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Control Panel→System→Device Administrator
Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes).
Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes.
(The maximum frequency per resolution may differ from product to product.)
Windows ME/2000/XP: Set the colors properly at the
Panel → Display → Settings
video card manual.
the Driver Installation Instructions.
Install the monitor driver according to the Driver Installation Instructions.
" and then reboot the computer
Control
.
to reinstall the adapter (video) driver.
If problems repeatedly occur, contact an authorized service center.

Q & A

Question Answer
How can I change the frequency? Frequency can be changed by reconfiguring the video card.
How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control
How can I set the Power Saving function?
How can I clean the outer case/LCD Panel?
Self-Test Feature Check
Self-Test Feature Check | Warning Messages | Environment | Useful Tips
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.

Self-Test Feature Check

1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)
Panel→Display→Settings.
* Contact the video card manufacturer for details.
Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual).
Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.
This box appears during normal operation if the video cable becomes disconnected or damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
Useful Tips
z A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the
computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
z
Judging the monitor's working condition
If there is no image on the screen or a
message comes up, disconnect the cable from the computer while the monitor is still powered on.
60Hz"
If there is a message coming up on the screen or if the screen goes white, this means the monitor is
{
"Not Optimum Mode","Recommended Mode 1280 x 1024
in working condition.
{ In this case, check the computer for trouble.
General

General

Model Name SAMTRON 94B
LCD Panel
Size 19 inch Diagonal (48 cm)
Display area 372.32 mm (H) x 301.56 mm (V)
Pixel Pitch 0.294 mm (H) x 0.294 mm (V)
Type a-si TFT active matrix
Synchronization
Horizontal 30 ~ 81 kHz
Vertical 56 ~ 75 Hz
Display Color
16.2 M Colors
Resolution
Optimum resolution 1280 x 1024@60 Hz
Maximum resolution 1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p Positive at 75 Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
Maximum Pixel Clock
135 MHz
Power Supply
AC 100 ~ 240 VAC(+/- 10 %), 60/50 Hz ± 3 Hz
Signal Cable
15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, detachable(option)
Power Consumption(maximum)
Less than 38 W
Dimensions (WxDxH)/ Weight
428.0 X 61.8 X 357.5 mm / 16.9 x 2.4 x 14.1 inch (Without Stand)
428.0 X 204.0 X 433.0 mm / 16.9 x 8.0 x 17.0 inch (With Basic Stand) / 6.25 kg
VESA Mounting Interface
100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating Temperature: 50 °F ~ 104 °F(10 °C ~ 40 °C)
Humidity: 10 % ~ 80 %, non-condensing
Storage Temperature:-4 °F ~113 °F (-20 °C ~ 45 °C)
Humidity: 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness.
For example, the number of TFT LCD sub pixels that is contained in this product are 3,932,160.
z
Note: Design and specifications are subject to change without prior notice.

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
EPA/ENERGY 2000
Power Switch off
Power Indicator Green Green, Blinking Black
Power Consumption Less than 38 W
Less than 1 W
(Off-mode)
Less than 1 W
(230 Vac)
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS

Preset Timing Modes

functionality.
®
As an ENERGY STAR
Partner, SAMSUNG has determined that this
product meets the ENERGY STAR
®
guidelines for energy efficiency.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350 31.469 70.086 25.175 +/-
IBM, 640 x 480 31.469 59.940 25.175 -/-
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.00 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 -/-
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.00 +/+
VESA, 1280 x 1024 63.981 60.020 108.00 +/+
VESA, 1280 x 1024 79.976 75.025 135.00 +/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America
CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca
MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx
U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com
Latin America
ARGENTINE 0800-333-3733 http://www.samsung.com/ar
BRAZIL 0800-124-421 http://www.samsung.com/br
CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl
COSTA RICA 0-800-507-7267 http://www.samsung.com/latin
ECUADOR 1-800-10-7267 http://www.samsung.com/latin
EL SALVADOR 800-6225 http://www.samsung.com/latin
GUATEMALA 1-800-299-0013 http://www.samsung.com/latin
JAMAICA 1-800-234-7267 http://www.samsung.com/latin
PANAMA 800-7267 http://www.samsung.com/latin
PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin
REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin
TRINIDAD & TOBAGO 1-800-7267-864 http://www.samsung.com/latin
VENEZUELA 1-800-100-5303 http://www.samsung.com/latin
Europe
BELGIUM 02 201 2418 http://www.samsung.com/be
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz
DENMARK 38 322 887 http://www.samsung.com/dk
FINLAND 09 693 79 554 http://www.samsung.com/fi
FRANCE 08 25 08 65 65 (€ 0,15/min) http://www.samsung.com/fr
GERMANY 01805 - 121213 (€ 0,12/Min) http://www.samsung.de
HUNGARY 06 40 985 985 http://www.samsung.com/hu
ITALIA 199 153 153 http://www.samsung.com/it
LUXEMBURG 02 261 03 710 http://www.samsung.lu
NETHERLANDS 0900 20 200 88 (€ 0.10/Min) http://www.samsung.com/nl
NORWAY 231 627 22 http://www.samsung.com/no
POLAND 0 801 801 881 http://www.samsung.com/pl
PORTUGAL 80 8 200 128 http://www.samsung.com/pt
SLOVAKIA 0850 123 989 http://www.samsung.com/sk
SPAIN 902 10 11 30 http://www.samsung.com/es
SWEDEN 08 585 367 87 http://www.samsung.com/se
U.K 0870 242 0303 http://www.samsung.com/uk
CIS
RUSSIA 8-800-200-0400 http://www.samsung.ru
UKRAINE 8-800-502-0000 http://www.samsung.com/ur
Asia Pacific
AUSTRALIA 1300 362 603 http://www.samsung.com/au
CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn
HONG KONG 2862 6001 http://www.samsung.com/hk
INDIA 3030 8282, 1600 1100 11 http://www.samsung.com/in
INDONESIA 0800-112-8888 http://www.samsung.com/id
JAPAN 0120-327-527 http://www.samsung.com/jp
MALAYSIA 1800-88-9999 http://www.samsung.com/my
PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph
SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg
THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th
TAIWAN 0800-329-999 http://www.samsung.com/tw
VIETNAM 1 800 588 889 http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za
U.A.E 800SAMSUNG (7267864) http://www.samsung.com/mea

Terms

Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz
Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen.
Example: If the resolution is 1280 x 1024 , this means the screen is composed of 1280
horizontal dots (horizontal resolution) and 1024 vertical lines (vertical resolution).

For Better Display

1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD.
{ Resolution: 1280 x 1024 { Vertical frequency (refresh rate): 60 Hz
2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness.
For example, the number of TFT LCD sub pixels that is contained in this product are
{
3,932,160.
3. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly. If excessive force is applied, you can have a stain on it.
4. If you are not satisfied with the quality of picture, you can get better quality of picture by executing "auto adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.
5. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.

Authority

Information in this document is subject to change without notice. © 2006 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
Class B
This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer to "Regulatory" Guide.
MÉXICO
IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864
EXPORTADO POR: Samsung Electronics CO.,LTD.
416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea
PRODUCT INFORMATION (Image Retention Free)
A
A
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention
Power Off, Screen Saver, or Power Save Mode
Ex)
z Turn the power off when using a stationary pattern.
- Turn the power off for 4 hours after 24 hours in use
- Turn the power off for 2 hours after 12 hours in use
z Use a Screen saver if possible
- Screen saver in one color or a moving image is recommended.
z Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
void using a combination of characters and background color with large
difference in luminance.
void using Grey colors, which can cause Image retention easily.
z Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
z Recommended settings: Bright colors with little difference in luminance
- Change the characters color and background color every 30 minutes Ex)
- Every 30 minutes, change the characters with movement. Ex)
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Loading...