Samsung SYNCMASTER 721N User Manual

Install drivers Install programs

SyncMaster 721N

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to
the equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Ground to prevent an electric shock

Power

When not used for an extended period of time, set your computer to DPMS.
If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Do not use a damaged or loose plug.

z This may cause electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

(Class l Equipment only.)

Insert the power plug firmly so that it does not come loose.

z A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon
them, which could cause damage.

z This may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

z This may cause fire.

Do not disconnect the power cord while using the monitor.

A surge may be caused by the separation and may damage the monitor.

z

Do not use the power cord when the connector or plug is dusty.

z If the connector or plug of the power cord is dusty, clean it with a dry

cloth.

z Using the power cord with a dusty plug or connector may cause electric

shock or fire.

To disconnect the apparatus from the mains, the plug must be pulled out
from the mains socket, therefore the mains plug shall be readily
operable.

z This may cause electric shock or fire.

Installation

Be sure to contact an authorized Service Center, when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.

Failure to do so may cause serious damage to your monitor.

Place your monitor in a location with low humidity and a minimum of
dust.

z Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or the person carrying it.

z

Install the monitor base in a showcase or shelf so that the end of the
base does not protrude from the showcase or shelf.

Dropping the product may cause damage to the product or the person

z

carrying it.

Do not place the product on an unstable or small surface area.

z Place the product on an even end stable surface ,as the product may fall

and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

z Take care, as someone, specifically children may trip over it.

To prevent the spread of fire, keep candles or other open flames away
from this product at all times.

z Otherwise, this may cause fire.

Keep any heating devices away from the power cable.

z A melted coating may cause electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a
bookshelf, closet, etc.

z Any increase in the internal temperature may cause fire.

Put down the monitor carefully.

z Failing to do so may damage the monitor.

Do not place the monitor face down.

This may damage the TFT-LCD surface.

z

The installation of the bracket must be done by a qualified professional.

z Installing the bracket by unqualified personnel may result in injury.

Always use the mounting device specified in the owner's manual.

z

When installing the product, make sure to keep it away from the wall
(more than 10 cm/4 inches ) for ventilation purposes.

z Poor ventilation may cause an increase in the internal temperature of the

product, resulting in a shortened component life and degraded
performance.

Keep the plastic packaging (bag) out of children's reach.

z The plastic packaging (bag) may cause suffocation if children play with

it.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with
a slightly moistened, soft fabric.

Do not spray water or detergent directly onto the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it
properly using a dry cloth.

A dirty connector may cause electric shock or fire.

z

Make sure to unplug the power cord before cleaning the product.

z Otherwise, this may cause electric shock or fire.

Others

Unplug the power cord from the power outlet and wipe the product using
a soft, dry cloth.

z Do not use any chemicals such as wax, benzene, alcohol, thinners,

insecticide, air freshener, lubricant or detergent.

Contact the SAMSUNG customer care center or Customer Center for
interior cleaning once a year.

z Keep the product's interior clean. Dust which has accumulated in the

interior over an extended period of time may cause a malfunction or fire.

Do not remove the cover (or back).

z This may cause electric shock or fire.
z Refer to a qualified servicing company.

If your monitor does not operate normally - in particular, if there is any

unusual sound or smell coming from the monitor - unplug it immediately
and the Service Center.

z This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture;
do not install inside a vehicle.

This may cause a malfunction, electric shock or fire.

z
z In particular, avoid operating the monitor near water or outdoors where

the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off
and unplug the power cord. Then contact the Service Center .

z The monitor may malfunction, causing electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is
not used for a long period of time.

z Failure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal
cable.

z This may cause a breakdown, electric shock or fire due to damage to

the cable.

Do not move the monitor right or left by pulling only the wire or the
signal cable.

z This may cause a breakdown, electric shock or fire due to damage to

the cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects
on the monitor.

z This may cause a malfunction, electric shock or fire.
z If a foreign substance enters the monitor, unplug the power cord and

contact the Service Center.

Keep the product away from combustible chemical sprays or
inflammable substances.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and tools or
inflammable objects such as paper or matches into the vent, headphone
port or AV ports or etc.

z It may cause a fire or an electric shock. If an alien substances or water

flows into the product, turn the product off, unplug the power connector
from the wall outlet and contact the Service Center.

When viewing a fixed screen for an extended period of time, residual
image or blurriness may appear.

z Change the mode to energy saving mode or set a screensaver to a

changing picture when away from the monitor for an extended period of
time.

Adjust the resolution and frequency to the level appropriate for the
model.

z An inappropriate resolution may cause undesirable picture quality.

17 inch (43 cm) - 1280 X 1024

Viewing the monitor continuously at a too close angle may result in
damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of
using the monitor

.

Do not install the product on an unstable, uneven surface or a location
prone to vibrations.

z Dropping the product may cause damage to the product or the person

carrying it. Using the product in a location prone to vibrations may
shorten the lifetime of the product or may cause the product to catch fire.

When moving the monitor, turn off and unplug the power cord.
Make sure that all cables, including the antenna cable and cables
connected to other devices, are disconnected before moving the
monitor.

z Failure to disconnect cables may damage it and cause fire or electric

shock.

Place the product out of children's reach, as they could damage by
hanging onto it.

z A falling product may cause injury to the person or even fatality.

When not using the product for an extended period of time, keep the
product unplugged.

z Otherwise, this may cause heat emission from the accumulated dirt or

degraded insulation, causing electric shock or fire.

Do not place your children's favorite toys or any other objects of interest
on the product.

z Children may try to climb on the product to retrieve an object. The

product could fall, causing injury or even fatality.

When lifting up or moving the monitor, do not lift the monitor upside
down while holding only the stand.

z This may cause your monitor to fall, and become damaged or cause

personal injury.

Good Postures When Using the Monitor

Try to maintain a good posture when using the monitor.

z Keep your back straight.

Keep a distance of about 45 ~ 50 cm between your eyes and

z

the monitor screen. Look at the screen from slightly above it,
and have the monitor directly in front of you.

z Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor

height so that the top of the monitor is slightly below eye level.
Adjust the monitor angle so that there is no reflected light on

z

the screen.Try to maintain your arms perpendicular to your
armpits.

z Keep your arms level with the back of your hands.
z Keep the angle of the elbow perpendicular.
z Keep the angle of the knees at more than 90 degree. Do not let

your feet fall up from the floor. Adjust the arm position so that it
is below the heart.

r

r

p

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

Unpacking

Without Stand

to buy optional items.

With Stand

Manual

Monito

Monitor & Sim

le stand Bottom

g

Cable

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

Ma

icTune™ software

Front

D-Sub Cable Power Cord

1. MENU button [ ]

2. MagicBright button
[]

Opens the OSD menu. Also use to exit the OSD menu or return to
the previous menu.

MagicBright is a new feature providing optimum viewing
environment depending on the contents of the image you are
watching. Currently four different modes are available: Custom,
Text, Internet, and Entertain. Each mode has its own pre­configured brightness value. You can easily select one of four
settings by simply pressing MagicBright control button.

1) Custom

Although the values are carefully chosen by our engineers, the
pre-configured values may not be comfortable to your eyes
depending on your taste.

g

3.
Brightness button [ ]

2,3. Adjust buttons [ ]

4. Enter button [ ]

5. AUTO button

6. Power button [ ]

7. Power indicator

See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when
leaving it unattended for long periods.

If this is the case, adjust the brightness and contrast by using
the OSD menu.

: Normal brightness

2) Text

For documentations or works involving heavy text.

3) Internet

For working with a mixture of images such as texts and
graphics.

4) Entertain

For watching motion pictures such as a DVD or VCD.

>>Click here to see an animation clip

When OSD is not on the screen, push the button to adjust
brightness.

Adjust items in the menu.

Activates a highlighted menu item.

Use this button for auto adjustment.

Use this button for turning the monitor on and off.

This light glows green during normal operation, and blinks green
once as the monitor saves your adjustments.

: Medium brightness

: High brightness

Rear

(The configuration at the back of the monitor may vary from product to product.)

1. POWER port

2. D-sub 15-pin port

3. Kensington Lock

Connect the power cord for your monitor to the power port on the back
of the monitor.
Connect the signal cable to the 15-pin, D-sub connector on the back
of your monitor.
The Kensington lock is a device used to physically fix the system
when using it in a public place.
(The locking device has to be purchased separately.)

For usin

a locking device, contact where you purchased it.

See Connecting the Monitor for further information regarding cable connections.

Connecting the Monitor

1.

2.

Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.

Use appropriate connection for your computer.

2-1.

2-2.

If the monitor and the computer are connected, you can turn them on and use them.

Using the Stand

Monitor Assembly

Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.

Monitor and Bottom

Attaching a Base

This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.

Monitor

A.

Mounting interface pad (Sold separately)

B.

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the
screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it
with four screws that came with the arm-type base, wall mount hanger or other base.

Installing the Monitor Driver (Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.

Prepare a blank disk and download the driver program file at the Internet web site shown
below.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)
http://www.samsungmonitor.com.cn/ (China)

1. Insert CD into the CD-ROM drive.

2. Click

"Windows"

3. Choose your monitor model in the model list, then click the

button.

"OK"

4. If you can see following message window, then click the
Then click

button. (Microsoft

"OK"

®

Windows® XP Operating System)

This monitor driver is under certifying MS logo,and this installation doesn't
damage your system.The certified driver will be posted on Samsung
Monitor homepage

http://www.samsung.com/.

5. Monitor driver installation is completed.

"Continue Anyway"

button.

Installing the Monitor Driver (Manual)

Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux

When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.

Prepare a blank disk and download the driver program file at the Internet web site shown
below.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)
http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows Vista™ Operating System

1. Insert your Manual CD into your CD-ROM drive.

2. Click (Start) and "

Personalization

".

Control Panel

". Then, double-click on "

3. Click "

Personalization

" and then "

Display Settings

".

Appearance and

4. Click "

Advanced Settings…

".

5. Click "

Properties

" in the "

Monitor

" tab. If the "

Properties

" button is deactivated, it
means the configuration for your monitor is completed. The monitor can be used as is.
If the message “
click "

Continue

Windows needs…

".

” is displayed, as shown in the figure below,

This monitor driver is under certifying MS logo, and this installation doesn't
damage your system.
The certified driver will be posted on Samsung Monitor homepage

http://www.samsung.com/

6. Click "

7. Check the "

Update Driver…

Browse my computer for driver software

pick from a list of device drivers on my computer

" in the "

Driver

" tab.

" checkbox and click "

".

Let me

8. Click "

9. Select the model that matches your monitor from the list of monitor models on the

Have Disk…

file is located, and click "OK".

screen, and click "

" and select the folder (for example, D:\Drive) where the driver setup

".

Next

10.

Click "
sequence.

Close

"→ "

" → "OK" → "OK" on the following screens displayed in

Close

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

Start

" —> "

Control Panel

" then click the "

Appearance and Themes

" Icon.

3. Click "

4. Click the "

Display

" icon and choose the "

Properties

" button on the "

Settings

Monitor

" tab then click "

" tab and select "

Advanced..

Driver

".

" tab.

5. Click "

6. Select "

Update Driver..

Don't search ,I will..

" and select "

Install from a list or..

" then click "

Next

" then click "

" and then click "

Have disk

Next

" button.

".

7. Click the "
model list and click the "

8. If you can see following "
click "OK" button.

Browse

" button then choose A:(D:\Driver) and choose your monitor model in the

" button.

Next

Message

" window, then click the "

Continue Anyway

" button. Then

This monitor driver is under certified MS logo,and this installation doesn't damage your
system.The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung.com/

9. Click the "

" button then click "OK" button continually.

Close

10. Monitor driver installation is completed.

Microsoft

®

Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "

2. Click the "

Browse

" button on the "

Insert disk

" window.

File Needed

" window.

3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.

How to install

1. Click "

2. Double click the "

3. Choose the "

4. Choose "

Start

Monitor

" , "

Setting

Settings

" , "

Control Panel

Display

" Icon.

" tab and then click "

".

".

Advanced..

".

Case1: If the "Properties" button is inactive, it means your monitor is properly configured.

Please stop installation

Case2: If the "Properties" button is active, click the "Properties" button then follow next steps

continually.

5. Click "

6. Choose "

specific driver

7. Click the "

8. Click the "

9. Choose your monitor model and click the "

10. Click the "

" and then click on "

Driver

Update Driver..

" then click on the "Next" button.

Display a list of the known drivers for this device so that I can choose a

" then click "

Browse
Open

Finish

" button then choose A:(D:\Driver).

" button, then click "OK" button.

" button then the "

" and then click "

Next

Close

Have disk

" button then click "

Next

" button.

".

Next

" button.

If you can see the "

r

And click the "

Finish

Digital Signature Not Found

" button then the "

Close

" button.

" window then click the "

Yes

"button.

Microsoft

1. Click "

2. Double click "

3. Select the "

4. Select the "

5. Click the "

6. Choose "

7. Choose "

8. Click the "

®

Windows® Millennium Operating System

" , "

Start

Setting

Display
Settings
Monitor

Change

Specify the location of the driver

" , "

Control Panel

" icon.

" tab and click "

" tab.

" button in the "

".

Advanced Properties

Monitor Type

".

" area.

Display a list of all the driver in a specific location..

Have Disk

" button

" button.

" then click "

Next

" button.

9. Specify A:\(D:\driver) then click "OK" button.

10. Select "

Show all devices

" and choose the monitor that corresponds to the one you

connected to your computer and click "OK".

11. Continue choosing "

" button and "OK" button until you close the Display Properties

Close

dialogue box.

Microsoft

1. Click

2. In Display Registration Information window, click Settings Tab and then click

Modes

®

Windows® NT Operating System

Start, Settings, Control Panel

.

, and then double-click

Display

icon.

All Display

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click OK.

4. Click

button if you see the screen working normally after clicking

Apply

. If the screen is

Test

not normal, change to a different mode (lower mode of resolution, colors or frequency).

If there is no Mode at

All Display Modes

, select the level of resolution and vertical

frequency by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. The third screen is for

setting your mouse

.

3. Set a mouse for your computer.

4. The next screen is for

selecting a keyboard

.

5. Set a Keyboard for your computer.

6. The next screen is for

7. First of all, set a

horizontal frequency

setting your monitor

.

for your monitor. (You can enter the frequency

directly.)

8. Set a

vertical frequency

9. Enter the

model name of your monitor

for your monitor. (You can enter the frequency directly.)

. This information will not affect the actual execution

of X-Window.

10. You have

Execute

finished

X-Window after setting other requested hardware.

setting up your monitor.

Natural Color

Natural Colo

One of the recent problems in using a computer is that the color of the images printed out by a
printer or other images scanned by a scanner or a digital camera are not the same as those
shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics &
Telecommunications Research Institute (ETRI).
This is only available for Samsung monitors and ensures that the color of the images on the
monitor are the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.

on the

"Start"

menu and then double-click

"Add/Delete"

button.

"Add/Delete a

Installing the Natural Color Software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural
Color screen will appear. Click on Natural Color in the startup window to install the Natural
Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD­ROM Drive, click the Windows [Start] button, select [Run...].
Enter D:\color\NCProsetup.exe and then press the <Enter> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)

Uninstalling the Natural Color Software Program

Select

"Setting/Control Panel"

program"

Select Natural Color from the list and then click the

.

Use this button for open the on-screen menu and exits from the menu screen or closes screen

1.

adjustment menu.

This button allows you to adjust items in the menu.

2.

This button allows you to adjust items in the menu.

3.

Press this button to activate a highlighted menu item.

4.

Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are

5.

adjusted automatically.

AUTO

Menu Description

AUTO

MagicBright™

When the '

' button is pressed, the Auto Adjustment screen appears

AUTO

as shown in the animated screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming video
signal. The values of fine, coarse and position are adjusted automatically.

To make the automatic adjustment function sharper, execute the 'AUTO'
function while the AUTO PATTERN is on.

z If Auto Adjustment does not work properly, press AUTO button again

to adjust picture with more accuracy.

z If you change resolution in the control panel, auto function will be

executed automatically.

Menu Description

Then push the MagicBright button again to circle through available

MagicBright™

preconfigured modes.

- four different modes(Custom/Text/Internet/Entertain)

Brightness

Menu Description

Brightness

1. Picture

2. Color

3. Image

4. OSD

5. Setup

6. Information

Picture

Adjust Brightness.

Brightness Contrast

Color Tone Color Control Gamma

Coarse Fine Sharpness H-Position V-Position

Language H-Position V-Position Transparency Display Time

Image Reset Color Reset

Menu Description Play/Stop

Brightness

Contrast

Color

Adjust the Brightness.

Adjust the Contrast.

Menu Description Play/Stop

Color Tone

Color Control

The tone of the color can be changed and one of four
modes can be selected - Cool, normal, Warm and Custom.

Follow these steps to adjust individual R,G,B color
balance.

Gamma correction changes the luminance of the colors
with intermediate luminance.

Gamma

Image

Mode 1

z
z Mode 2
z Mode 3

Menu Description Play/Stop

Removes noise such as vertical stripes. Coarse

Coarse

adjustment may move the screen image area. You may
relocate it to the center using the horizontal control menu.

Removes noise such as horizontal stripes. If the noise

Fine

persists even after fine tuning, repeat it after adjusting the
frequency (clock speed).

Sharpness

H-Position

V-Position

Follow these instuction to change the clearance of image.

Follow these instructions to change the horizontal position
of the monitor's entire display.

Follow these instructions to change the vertical position of
the monitor's entire display.

OSD

Menu Description Play/Stop

You can choose one of 7 languages.

Language

H-Position

V-Positon

Transparency

Display Time

Setup

:The language chosen affects only the language of

Note

the OSD. It has no effect on any software running on the
computer.

You can change the horizontal position where the OSD
menu appears on your monitor.

You can change the vertical position where the OSD menu
appears on your monitor.

Change the transparency of the background of the OSD.

The menu will be automatically turned if no adjustments
are made for a certain time period.
You can set the amount of time the menu will wait before it
is turned off.

Menu Description Play/Stop

Image Reset

Color Reset

Information

Image parameters are replaced with the factory default
values.

Color parameters are replaced with the factory default
values.

Menu Description

Information

Shows a video source, display mode on the OSD screen.

Installation

1. Insert the installation CD into the CD-ROM drive.

2. Click the MagicTune™ installation file.

3. Select installation Language, Click "Next".

4. When the Installation Shield Wizard window appears, click "Next."

5. Select "I agree to the terms of the license agreement" to accept the terms of use.

6. Choose a folder to install the MagicTune™ program.

7. Click "Install."

8. The "Installation Status" window appears.

9. Click "Finish."

10. When the installation is completed, the MagicTune™ executable icon appears on your desktop.

Double-click the icon to start the program.

MagicTune™ execution icon may not appear depending on specification of computer
system or monitor. If that happens, press F5 Key.

Installation Problems

The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network
environment.

System Requirements

OS

z Windows 2000
z Windows XP Home Edition
z Windows XP Professional
z Windows Vista™

It is recommended using MagicTune™ in Windows® 2000 or
later.

Hardware

z 32 MB Memory above
z 60 MB Hard disk space above

* For more information, visit the MagicTune™

website

.

Uninstall

The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the
Windows® Control Panel.

Perform the following steps remove MagicTune™ .

1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on
Windows® XP, go to [Control Panel] in the [Start] menu.

2. Click the "Add or Remove Programs" icon in Control Panel.

3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™ ." Click on it to highlight
it.

4. Click the "Change/Remove" button to remove the program.

5. Click "Yes" to begin the uninstall process.

6. Wait until the "Uninstall Complete" dialog box appears.

Visit the MagicTune™
software upgrades.

website for technical support for MagicTune™ , FAQs (questions and answers) and

Check List

Before calling for assistance, check the information in this section to see if you can remedy
any problems yourself. If you do need assistance, please call the phone number on the

Information section or contact your dealer.

Symptom Check List Solutions

No images on the
screen. I cannot
turn on the
monitor.

Is the power cord connected
properly?

Can you see

Cable"

If the power is on, reboot the
computer to see the initial
screen(the login screen),
which can be seen.

Can you see

Mode","Recommended
Mode 1280 x 1024 60Hz"

the screen?

"Check Signal

on the screen?

"Not Optimum

on

Check the power cord connection
and supply.

Check the signal cable connection.

If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows ME/XP/2000) and then
change the frequency of the video
card.
(Refer to the Preset Timing Modes)

Note: If the initial screen (the login
screen) does not appear, contact

the Service Center or your dealer.

You can see this message when the
signal from the video card exceeds
the maximum resolution and
frequency that the monitor can
handle properly.

Adjust the maximum resolution and
frequency that the monitor can
handle properly.

If the display exceeds SXGA or
75Hz, a

Mode","Recommended Mode
1280 x 1024 60Hz"

displayed. If the display exceeds
85Hz, the display will work properly
but the

Mode","Recommended Mode
1280 x 1024 60Hz"

appears for one minute and then
disappears.

"Not Optimum

message is

"Not Optimum

message

Please change to the recommended
mode during this one-minute period.

(The message is displayed again if
the system is rebooted.)

The screen shows
strange colors or
just black and
white.

The screen
suddenly has
become
unbalanced.

The screen is out
of focus or OSD
cannot be
adjusted.

There is no image on the
screen.
Is the power indicator on the
monitor blinking at 1 second
intervals?

Is the screen displaying only
one color as if looking at the
screen through a cellophane
paper?

Have the screen colors
become strange after running
a program or due to a crash
between applications?

Has the video card been set
properly?

Have you changed the video
card or the driver?

Have you adjusted the
resolution or frequency to the
monitor?

The screen can be unbalanced due to the cycle of the video card signals.
Readjust Position by referring to the OSD.

Have you adjusted the
resolution or frequency on the
monitor?

The monitor is in PowerSaver mode.

press a key on the keyboard to
activate the monitor and restore the
image on the screen.

Check the signal cable
connection.Make sure the video
card is fully inserted in it's slot.

Reboot the computer.

Set the video card by referring to the
video card manual.

Adjust screen image position and
size using the OSD.

Adjust the resolution and frequency
at the video card.
(Refer to the Preset Timing Modes).

Adjust the resolution and frequency
of the video card.
(Refer to the Preset Timing Modes).

LED is blinking but
no images on the
screen.

There are only 16
colors shown on
the screen.
The screen colors
have changed after
changing the video
card.

There is a
message that
reads
"Unrecognized
monitor, Plug &
Play (VESA DDC)
monitor found".

Check when
MagicTune™ does
not function
properly.

Is the frequency properly
adjusted when checking the
Display Timing on the menu?

Have the Windows colors been
set properly?

Has the video card been set
properly?

Have you installed the monitor
driver?

See the video card manual to
see if the Plug & Play (VESA
DDC) function can be
supported.

MagicTune™ feature is found
only on PC (VGA) with
Window OS that supports Plug
and Play.

Adjust the frequency properly by
referring to the video card manual
and the Preset Timing Modes.

(The maximum frequency per
resolution may differ from product to
product.)

Windows ME/2000/XP:
Set the colors properly at the

Control Panel → Display →
Settings

Set the video card by referring to the
video card manual.

Install the monitor driver according
to the Driver Installation Instructions.

Install the monitor driver according
to the Driver Installation Instructions.

* To check whether your PC is
available for MagicTune™ feature,
follow the
steps below (When Windows is
XP);

Control Panel -> Performance and
Maintenance -> System ->
Hardware -> Device Manager ->
Monitors -> After deleting Plug and

.

Play monitor, find 'Plug and Play
monitor' by searching new
Hardware.

MagicTune™ is an additional
software for the monitor. Some
graphic cards may not support your
monitor. When you have a problem
with the graphic card, visit our
website to check the compatible
graphic card list provided.

http://www.samsung.com/monitor/MagicTune

MagicTune™
doesn't work
properly.

Did you install the program? Reboot the computer after installing the

Visit the MagicTune™ website and download the installation software for MagicTune™
MAC.

Check the following items if there is trouble with the monitor.

1. Check if the power cord and the video cables are properly connected to the computer.

2. Check if the computer beeps more than 3 times when booting.

(If it does, request an after-service for the main board of the computer.)

3. If you installed a new video card or if you assembled the PC, check if the installed the adapter

(video) driver and the monitor driver.

4. Check if the scanning ratio of the video screen is set at 56Hz ~ 75Hz.

(Do not exceed 75Hz when using the maximum resolution.)

5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,

remove the Display Adapter at the "
reboot the computer to reinstall the adapter (video) driver.

If problems repeatedly occur, contact an authorized Service Center.

Have you changed your PC or
video graphic card?

Control Panel→System→Device Administrator

Download the latest program. The
program can be downloaded

http://www.samsung.com/monitor/MagicTune.

program for the first time. If a copy of the
program is already installed, remove it,
reboot the computer, and then install the
program again. You need to reboot the
computer for it to operate normally after
installing or removing the program.

" and then

Q & A

Question

How can I change the
frequency?

How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control

How can I set the Power Saving
function?

How can I clean the outer
case/LCD Panel?

Frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version
of the driver used. (Refer to the computer or the video card
manual for details.)

Panel→Display→Settings.

* Contact the video card manufacturer for details.

Windows ME/XP/2000 : Set the function at BIOS-SETUP of the
computer or the screen saver. (Refer to Windows/Computer
Manual).

Disconnect the power cord and then clean the monitor with a soft
cloth, using either a cleaning solution or plain water.

Answer

Y

Do not leave any remains of the detergent nor scratch the case.
Do not allow any water to go inside the monitor.

Self-Test Feature Check

Self-Test Feature Check | Warning Messages | Environment | Useful Tips

our monitor provides a self test feature that allows you to check whether your monitor is

functioning properly.

Self-Test Feature Check

1. Turn off both your computer and the monitor.

2. Unplug the video cable from the back of the computer.

3. Turn on the monitor.

If the monitor is functioning properly, you will see a box in the illustration below.

This box appears during normal operation if the video cable becomes disconnected or
damaged.

4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the

monitor.
If your monitor screen remains blank after using the previous procedure, check your video
controller and computer system; your monitor is functioning properly.

Warning Messages

If there is something wrong with the input signal, a message appears on the screen or the
screen goes blank although the power indicator LED is still on. The message may indicate
that the monitor is out of scan range or that you need to check the signal cable.

Environment

The location and the position of the monitor may influence the quality and other
features of the monitor.

1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer
to another room.

2. Remove all electronic devices such as radios, fans, clocks and telephones that are
within 3 feet (one meter) of the monitor.

Useful Tips

z A monitor recreates visual signals received from the computer. Therefore, if there is trouble with

the computer or the video card, this can cause the monitor to become blank, have poor coloring,
noise, Video mode not supported, etc. In this case, first check the source of the problem, and
then contact the Service Center or your dealer.

z

Judging the monitor's working condition

If there is no image on the screen or a

1024 60Hz"

message comes up, disconnect the cable from the computer while the monitor is still

"Not Optimum Mode","Recommended Mode 1280 x

powered on.

If there is a message coming up on the screen or if the screen goes white, this means the

{

monitor is in working condition.

{ In this case, check the computer for trouble.

General

General

Model Name SyncMaster 721N

LCD Panel

Size 17" Diagonal (43 cm)

Display area 337.92 mm (H) x 270.336 mm (V)

Pixel Pitch 0.264 mm (H) x 0.264 mm (V)

Synchronization

Horizontal 30 ~ 81 kHz

Vertical 56 ~ 75 Hz

Display Color

16.2M Colors

Resolution

Optimum resolution 1280 x 1024@60 Hz

Maximum resolution 1280 x 1024@75 Hz

Input Signal, Terminated

RGB Analog
0,7Vp-p Positive at 75Ω
Separate H/V sync, Composite sync, SOG, TTL level positive or negative.

Maximum Pixel Clock

140 MHz

Power Supply

AC 100 to 240 VAC(+/- 10%) ,60/50Hz ± 3Hz

Signal Cable

15pin-to-15pin D-sub cable, detachable

Dimensions (WxHxD)/ Weight (Simple Stand)

370.0 x 316.0 x 60.3 mm / 14.6 x 12.4 x 2.4 inch (Without Stand)

370.0 x 386.5 x 195.4 mm / 14.6 x 15.2 x 7.7 inch (Without Stand) / 4.4kg / 9.7Ibs

VESA Mounting Interface

100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)

Environmental considerations

Operating Temperature: 50°F ~ 104°F(10°C ~ 40°C)

Humidity: 10% ~ 80%, non-condensing

Storage Temperature: -4°F ~113°F (-20°C ~ 45°C)

Humidity: 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Dot Acceptable

TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm
(one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE
color seem to be bright sometimes or some of black pixels could be seen. This is not from bad
quality and you can use it without uneasiness.

For example, the number of TFT LCD sub pixels that is contained in this product are 3,932,160.

z

Note: Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can
be used in all areas including common residential areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy
by switching your monitor into a low-power mode when it has not been used for a certain amount of
time. The monitor automatically returns to normal operation when you press a key on the keyboard. For
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in
your computer. Use a software utility installed on your computer to set up this feature.

Power off

State

Normal Operation

Power saving mode

(Power button)

EPA/ENERGY 2000

Power Indicator Green Green, Blinking Black

Power Consumption Less than 34W

Less than 1W

(Off-mode)

Less than 1W

(120Vac/220 Vac)

This monitor is EPA ENERGY STAR® compliant and ENERGY2000
compliant when used with a computer equipped with VESA DPMS
functionality.

As an ENERGY STAR

®

Partner, SAMSUNG has determined that this

product meets the ENERGY STAR

®

guidelines for energy efficiency.

g

Preset Timin

If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.

Modes

Horizontal

Display Mode

IBM, 640 x 350 31.469 70.086 25.175 +/-

IBM, 640 x 480 31.469 59.940 25.175 -/-

IBM, 720 x 400 31.469 70.087 28.322 -/+

MAC, 640 x 480 35.000 66.667 30.240 -/-

MAC, 832 x 624 49.726 74.551 57.284 -/-

MAC, 1152 x 870 68.681 75.062 100.00 -/-

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 640 x 480 37.861 72.809 31.500 -/-

VESA, 800 x 600 35.156 56.250 36.000 +/+

VESA, 800 x 600 37.879 60.317 40.000 +/+

VESA, 800 x 600 46.875 75.000 49.500 +/+

VESA, 800 x 600 48.077 72.188 50.000 +/+

VESA, 1024 x 768 48.363 60.004 65.000 -/-

VESA, 1024 x 768 56.476 70.069 75.000 -/-

Frequency

(kHz)

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

VESA, 1024 x 768 60.023 75.029 78.750 +/+

VESA, 1152 x 864 67.500 75.000 108.00 +/+

VESA, 1280 x 1024 63.981 60.020 108.00 +/+

VESA, 1280 x 1024 79.976 75.025 135.00 +/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of
the screen horizontally is called Horizontal Cycle and the inverse
number of the Horizontal Cycle is called Horizontal Frequency. Unit:
kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image
many times per second to display an image to the user. The
frequency of this repetition is called Vertical Frequency or Refresh
Rate. Unit: Hz

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please
contact the SAMSUNG customer care center.

North America

U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com

CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca

MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx

Latin America

ARGENTINE 0800-333-3733 http://www.samsung.com/ar

BRAZIL 4004-0000 http://www.samsung.com/br

CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl

COLOMBIA 01-8000112112 http://www.samsung.com.co

COSTA RICA 0-800-507-7267 http://www.samsung.com/latin

ECUADOR 1-800-10-7267 http://www.samsung.com/latin

EL SALVADOR 800-6225 http://www.samsung.com/latin

GUATEMALA 1-800-299-0013 http://www.samsung.com/latin

JAMAICA 1-800-234-7267 http://www.samsung.com/latin

PANAMA 800-7267 http://www.samsung.com/latin

PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin

REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin

TRINIDAD & TOBAGO 1-800-7267-864 http://www.samsung.com/latin

VENEZUELA 0-800-100-5303 http://www.samsung.com/latin

Europe

BELGIUM 02 201 2418 http://www.samsung.com/be

CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz

DENMARK 70 70 19 70 http://www.samsung.com/dk

FINLAND 030-6227 515 http://www.samsung.com/fi

FRANCE

GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de

HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu

ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it

LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu

NETHERLANDS 0900 20 200 88 (€ 0,10/Min) http://www.samsung.com/nl

NORWAY 815-56 480 http://www.samsung.com/no

POLAND 0 801 801 881 http://www.samsung.com/pl

PORTUGAL 80 8 200 128 http://www.samsung.com/pt

REPUBLIC OF IRELAND 0818 717 100 http://www.samsung.com/uk

SLOVAKIA 0800-SAMSUNG (7267864) http://www.samsung.com/sk

SPAIN 902 10 11 30 http://www.samsung.com/es

SWEDEN 0771-400 200 http://www.samsung.com/se

SWITZERLAND 0800-7267864 http://www.samsung.com/ch

U.K 0870 SAMSUNG (7267864) http://www.samsung.com/uk

3260 SAMSUNG(7267864)
(€ 0,15/min)

CIS

http://www.samsung.com/fr

ESTONIA 800-7267 http://www.samsung.ee

LATVIA 800-7267 http://www.samsung.com/lv

LITHUANIA 8-800-77777 http://www.samsung.lt

KAZAKHSTAN 8 800 080 1188 http://www.samsung.kz

RUSSIA 8-800-200-0400 http://www.samsung.ru

UKRAINE 8-800-502-0000 http://www.samsung.com/ur

UZBEKISTAN 140-1234 http://www.samsung.uz

Asia Pacific

AUSTRALIA 1300 362 603 http://www.samsung.com/au

CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn

HONG KONG 3698-4698 http://www.samsung.com/hk

INDIA 3030 8282, 1800 1100 11 http://www.samsung.com/in

INDONESIA 0800-112-8888 http://www.samsung.com/id

JAPAN 0120-327-527 http://www.samsung.com/jp

MALAYSIA 1800-88-9999 http://www.samsung.com/my

PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph

SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg

THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th

TAIWAN 0800-329-999 http://www.samsung.com/tw

VIETNAM 1 800 588 889 http://www.samsung.com/vn

Middle East & Africa

SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za

U.A.E

800SAMSUNG (7267864)
8000-4726

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the
higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image
for the user. The frequency of this repetition per second is called Vertical Frequency or
Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally
is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom in order is called the
Non-Interlace method while showing odd lines and then even lines in turn is called the
Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a
clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer
and the monitor to exchange information automatically. This monitor follows the international
standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for
performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1280 x 1024 , this means the screen is composed of 1280

horizontal dots (horizontal resolution) and 1024 vertical lines (vertical resolution).

http://www.samsung.com/mea

For Better Display

1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described
below to enjoy the best quality of picture. You can have an uneven quality of picture in the
screen if the best quality of picture is not provided in TFT-LCD.

{ Resolution: 1280 x 1024
{ Vertical frequency (refresh rate): 60 Hz

2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of
1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE
and WHITE color seem to be bright sometimes or some of black pixels could be seen.
This is not from bad quality and you can use it without uneasiness.

{ For example, the number of TFT LCD sub pixels that is contained in this product are

3,932,160.

3. When you clean the monitor and the panel outside, please apply the recommended small
amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but
to be scrubbed out softly.
If excessive force is applied, you can have a stain on it.

4. If you are not satisfied with the quality of the picture, you can get better quality of the picture
by executing "auto adjustment function" in display screen that is appeared as window
termination button is pressed.
If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.

5. If you view a fixed screen for an extended period of time, residual image or blurriness may
appear.
Change the mode to energy save or set a screensaver to move the picture when you need to
be away from the monitor for an extended period of time.

Authority

Information in this document is subject to change without notice.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are

registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and
logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an
ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets
the ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein
may be the trademarks or registered trademarks of their respective owners.

MÉXICO

IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.

Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: [phone]

EXPORTADO POR: Samsung Electronics CO.,LTD.

416, Mae tan-3dong, Yeongtong - gu,
Suwon City, Gyeonggi-do Korea

PRODUCT INFORMATION (Image Retention Free)

y

A

A

LCD Monitors and TVs may have an image retention when switching from one image to another
especially after displaying a stationary image for a long time.
This guide is to demonstrate a correct usage of LCD products in order to protect them from
Image retention.

Warrant

Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.

What is Image retention ?

During normal operation of a LCD panel, pixel image retention doesn't occur. However,
if the same image is displayed for a long time, a slight difference in electric charge
accumulates between the two electrodes which encase the liquid crystal. This may
cause the liquid crystal to build up in a certain areas of the display. Thus, the previous
image is retained when switching to a new video image. All display products, including
LCD,are subject to image retention. This is not a product defect.

Please follow the suggestions below to protect your LCD from image retention

Power Off, Screen Saver, or Power Save Mode

Ex)

z Turn the power off when using a stationary pattern.

- Turn the power off for 4 hours after 20 hours in use

- Turn the power off for 2 hours after 12 hours in use

z Use a Screen saver if possible

- Screen saver in one color or a moving image is recommended.

z Set the Monitor to power off with the PC Display Properties Power Scheme.

Suggestions for specific applications

Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems
We recommend that you follow set up of your display system program as below:

Display Information together with Logo or Moving image cycle.

Ex) Cycle : Display Information for 1 hour followed by a
Display Logo or moving image for 1 minute.

Change the Color Information periodically (Use 2 different colors).

Ex) Rotate the Color Information with 2 colors every 30 minutes.

void using a combination of characters and background color with large

difference in luminance.

void using Grey colors, which can cause Image retention easily.

z Avoid: Colors with big difference in luminance (Black & White, Grey)

Ex)

z Recommended settings: Bright colors with little difference in luminance

- Change the characters color and background color every 30 minutes
Ex)

- Every 30 minutes, change the characters with movement.

Ex)

The best way to protect your monitor from Image retention is to set your PC or
System to operate a Screen Saver program when you are not using it.

Image retention may not occur when a LCD panel is operated under normal conditions.

Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be
slight difference in voltage between electrodes that work the liquid crystal (LC) in a
pixel. The voltage difference between electrodes increases with time, forcing the liquid
crystal to lean. When this occurs, the previous image may be seen when the pattern is
changed.
To prevent this, the accumulated voltage difference must be decreased.

Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicates that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.