Samsung SYNCMASTER 2220LM User Manual

Page 1
SyncMaster 2220LM
SyncMaster 2220LM
Install drivers
Page 2
Model
SyncMaster 2220LM
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Prohibited Important to read and understand at all times
Do not disassemble Disconnect the plug from the outlet
Do not touch Ground to prevent an electric shock
Page 3
Power
Do not excessively bend the plug and wire nor place heavy objects upon
When not used for an extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug.
l
This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
l
This may cause electric shock or fire.
Use only a properly grounded plug and receptacle.
l
An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
Insert the power plug firmly so that it does not come loose.
l
A bad connection may cause fire.
them, which could cause damage.
l
This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet.
l
This may cause fire.
Page 4
A surge may be caused by the separation and may damage the monitor.
To disconnect the apparatus from the mains, the plug must be pulled out
a location with heavy dust, high or low temperatures, high humidity, and exposed
Do not disconnect the power cord while using the monitor.
l
Do not use the power cord when the connector or plug is dusty.
l
If the connector or plug of the power cord is dusty, clean it with a dry cloth.
l
Using the power cord with a dusty plug or connector may cause electric shock or fire.
from the mains socket, therefore the mains plug shall be readily operable.
l
This may cause electric shock or fire.
Installation
Be sure to contact an authorized Service Center, when installing your monitor in to chemical substances and where it operates for 24 hours such as at airports,
train stations etc. Failure to do so may cause serious damage to your monitor.
Place your monitor in a location with low humidity and a minimum of dust.
l
Failure to do so may cause electric shock or fire inside the monitor.
Do not drop the monitor when moving it.
Page 5
l
Place the product on an even and stable surface, as the product may fall
This may cause damage to the product or the person carrying it.
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.
l
Dropping the product may cause damage to the product or the person carrying it.
Do not place the product on an unstable or small surface area.
l
and cause harm to someone walking by, specifically children.
Do not place the product on the floor.
l
Take care, as someone, specifically children may trip over it.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
l
Otherwise, this may cause fire.
Keep any heating devices away from the power cable.
l
A melted coating may cause electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.
l
Any increase in the internal temperature may cause fire.
Put down the monitor carefully.
Page 6
l
Poor ventilation may cause an increase in the internal temperature of the
LCD screen, wipe with
Failing to do so may damage the monitor.
Do not place the monitor face down.
l
This may damage the TFT-LCD surface.The installation of the bracket must be done by a qualified professional.
Installing a wall bracket must be done by a qualified professional.
l
Installing the bracket by unqualified personnel may result in injury.
l
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.
l
product, resulting in a shortened component life and degraded performance.
Keep the plastic packaging (bag) out of children's reach.
l
The plastic packaging (bag) may cause suffocation if children play with it.
Clean
When cleaning the monitor case or the surface of the TFT­a slightly moistened, soft fabric.
Do not spray water or detergent directly onto the monitor.
Page 7
l
Unplug the power cord from the power outlet and wipe the product using
This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.
l
A dirty connector may cause electric shock or fire.
Make sure to unplug the power cord before cleaning the product.
l
Otherwise, this may cause electric shock or fire.
a soft, dry cloth.
l
Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year.
l
Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire.
Others
Do not remove the cover (or back).
Page 8
l
unplug it immediately
This may cause electric shock or fire.
l
Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor ­and contact an authorized dealer or the Service Center.
l
This may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.
l
This may cause a malfunction, electric shock or fire.
l
In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center .
l
The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.
l
Failure to do so may cause electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable.
l
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable.
l
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet.
Page 9
l
Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor.
l
This may cause a malfunction, electric shock or fire.
l
If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances.
l
This may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
l
This may cause electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc.
l
This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.
l
Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.
Adjust the resolution and frequency to the level appropriate for the model.
l
An inappropriate resolution may cause undesirable picture quality.
22 inch Wide (55.9cm) - 1680 X 1050
Page 10
Keep the volume at a comfortable level when using the headphones.
shorten the lifetime of the product or may cause the product to catch fire.
Do not place your children's favorite toys or any other objects of interest
l
Excessively loud volume level may damage hearing.
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor
.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
l
Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.
l
Failure to disconnect cables may damage it and cause fire or electric shock.
Place the product out of children's reach, as they could damage by hanging onto it.
l
A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged.
l
Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
on the product.
Page 11
l
Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor
Keep the angle of the knees at more than 90 degree. Do not let
Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.
l
This may cause your monitor to fall, and become damaged or cause personal injury.
Good Postures When Using the Monitor
Try to maintain a good posture when using the monitor.
l
Keep your back straight.
l
Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you.
l
height so that the top of the monitor is slightly below eye level.
l
Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits.
l
Keep your arms level with the back of your hands.
l
Keep the angle of the elbow perpendicular.
l
your feet fall up from the floor. Adjust the arm position so that it is below the heart.
Page 12
PRODUCT INFORMATION (Image Retention Free)
y
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention.
Warrant
Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention
Power Off, Screen Saver, or Power Save Mode
Ex)
z Turn the power off when using a stationary pattern.
- Turn the power off for 4 hours after 20 hours in use
- Turn the power off for 2 hours after 12 hours in use
z Use a Screen saver if possible
- Screen saver in one color or a moving image is recommended.
z Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily.
z Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
z Recommended settings: Bright colors with little difference in luminance
- Change the characters color and background color every 30 minutes Ex)
- Every 30 minutes, change the characters with movement.
Page 13
Ex)
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Page 14
Contact a local dealer
to buy optional items.
Monitor
Model
SyncMaster 2220LM
Unpacking
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Without stand
With stand
Page 15
Monitor & Simple Stand
Warranty Card/ Registration
Cable
RGB Cable
Power Cord
Audio Cable
Manual
Quick Setup Guide
Front
Card
(Not available in all locations)
User's Guide,
Monitor Driver
Page 16
MENU button [MENU/]
MagicBright [ ]
Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre­configured brightness value. You can easily select one of six settings by simply pressing MagicBright control button.
1) Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.
2) Text
For documentations or works involving heavy text.
3) Internet
For working with a mixture of images such as text and graphics.
4) Game
For watching motion pictures such as a game.
5) Sport
For watching motion pictures such as a sport.
6) Movie
Page 17
For watching motion pictures such as a DVD or Video CD.
>>Click here to see an animation clip
Volume button []
Adjust buttons [ ] Enter button [ ]
AUTO button [ AUTO ]
Power button [] Power indicator
Speaker
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
When OSD is not on the screen, push the button to adjust volume.
>>Click here to see an animation clip
Adjust items in the menu. Activates a highlighted menu item. Use this button for auto adjustment.
>>Click here to see an animation clip
Use this button for turning the monitor on and off. This light glows blue during normal operation, and blinks blue once
as the monitor saves your adjustments. You can hear sound by connecting the soundcard of your PC to the
monitor.
Rear
(The configuration at the back of the monitor may vary from product to product.)
Page 18
Connect the power cord for your monitor to the power port on the back
Connect the audio cable for your monitor to the audio port on the back
when using it in a public place. (The locking device has to be
For using a locking device, contact where you purchase it.
POWER port RGB IN port AUDIO IN Kensington Lock
of the monitor. Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
of your computer. The Kensington lock is a device used to physically fix the system
purchased separately. )
Headphone connection terminal
See Connecting the Monitor for further information regarding cable connections.
Page 19
Model
SyncMaster 2220LM
Connecting the Monitor
1.
Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.
2.
Use appropriate connection for your computer.
Using the D-sub (Analog) connector on the video card.
2-1.
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Connected to a Macintosh.
2-2.
[ RGB IN ]
Connect the monitor to the Macintosh computer using the D-sub connection cable.
Page 20
If the monitor and the computer are connected, you can turn them on and use them.
Monitor Assembly
Using the Stand
Monitor and Bottom
Attaching a Base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Page 21
Monitor
Align the mounting interface pad with the holes in the rear cover mounting Pad and secure
For wall mounts that do not comply with VESA standard screw specifications, the length of
Please use Wall Mount according to the International standards.
A.
Mounting interface pad (Sold separately)
B.
1.Turn off your monitor and unplug its power cord.
2.Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3.Remove screws and then remove the stand from the LCD monitor.
4. it with four screws that came with the arm-type base, wall mount hanger or other base.
l
Do not use screws longer than the standard dimension, as they may damage the inside of the Monitor.
l
the screws may differ depending on their specifications.
l
Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
l
Samsung is not liable for product damage or personal injury when a non-VESA or non­specified wall mount is used or the consumer fails to follow the product installation instructions.
l
To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface.
l
Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified.
l
Installing the Monitor Driver (Automatic)
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Page 22
posted on Samsung
Prepare a blank disk and download the driver program file at the Internet web site shown below.
l
Internet web site : http://www.samsung.com/ (Worldwide)
http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
1.Insert CD into the CD-ROM drive.
2.Click
"Windows"
3.Choose your monitor model in the model list, then click the
button.
"OK"
4.If you can see following message window, then click the Then click
button. (Microsoft® Windows® XP/2000 Operating System)
"OK"
This monitor driver is under certifying MS logo,and this installation doesn'tdamage your system.The certified driver will be Monitor homepage
http://www.samsung.com/.
5.Monitor driver installation is completed.
"Continue Anyway"
button.
Installing the Monitor Driver (Manual)
Page 23
Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown below.
l
Internet web site : http://www.samsung.com/ (Worldwide)
http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
Microsoft® Windows Vista Operating System
1.Insert your Manual CD into your CD-ROM drive.
2.Click (Start) and "
Personalization
".
Control Panel
". Then, double-click on "
Appearance and
3.Click "
4.
Personalization
" and then "
Display Settings
".
Click "
Advanced Settings
".
Page 24
5.Click " means the configuration for your monitor is completed. The monitor can be used as is. If the message click "
6.Click "
Properties
Continue
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage
http://www.samsung.com/
Update Driver
" in the "
Windows needs
".
Monitor
" in the "
Driver
" tab. If the "
is displayed, as shown in the figure below,
" tab.
Properties
" button is deactivated, it
7.
Check the "
pick from a list of device drivers on my computer
Browse my computer for driver software
" checkbox and click "
".
Let me
Page 25
8.Click " file is located, and click "OK".
9.Select the model that matches your monitor from the list of monitor models on the screen, and click "
Have Disk
" and select the folder (for example, D:\Drive) where the driver setup
".
Next
10.
Click " sequence.
Close
"→ "
Close
" → "OK" → "OK" on the following screens displayed in
Page 26
Microsoft® Windows® XP Operating System
1.Insert CD into the CD-ROM driver.
2.Click "
Start
" > "
Control Panel
" then click the "
Appearance and Themes
" Icon.
3.Click "
4.Click the "
Display
" icon and choose the "
Properties
" button on the "
Settings
Monitor
" tab then click "
" tab and select "
Advanced..
Driver
".
" tab.
Page 27
5.Click "
6.Select "
Update Driver..
Don't search ,I will..
" and select "
Install from a list or..
" then click "
" then click "
" and then click "
Next
Have disk
Next
".
" button.
7.Click the " model list and click the "
Browse
" button then choose A:(D:\Driver) and choose your monitor model in the
" button.
Next
Page 28
8.If you can see following " click "OK" button.
This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9.Click the "
Close
" button then click "OK" button continually.
Message
" window, then click the "
Continue Anyway
" button. Then
Page 29
Finish
Close
If the "Properties" button is active, click the "Properties" button then follow next steps
All Display Modes
10.Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
11 頁,共 12 頁SAMSUNG SyncMaster Monitor User's Manual
1.Choose "OK" button on the "
2.Click the "
3.Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.Click "
2.Double click the "
3.Choose the "
4.Choose "
Case1:If the "Properties" button is inactive, it means your monitor is properly configured. Case2:
5.Click "
6.Choose "
specific driver
7.Click the "
8.Click the "
9.Choose your monitor model and click the "
10.Click the " If you can see the "
And click the "
Microsoft® Windows® Millennium Operating System
1.Click "
2.Double click "
3.Select the "
4.Select the "
5.Click the "
6.Choose "
7.Choose "
8.Click the "
9.Specify A:\(D:\driver) then click "OK" button.
10.Select " connected to your computer and click "OK".
11.Continue choosing " dialogue box.
Microsoft® Windows® NT Operating System
1.Click
2.In Display Registration Information window, click Settings Tab and then click
Modes
3.Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.
4.Click not normal, change to a different mode (lower mode of resolution, colors or frequency).
Start
Please stop installation continually.
Driver
Start
Show all devices
Start, Settings, Control Panel
.
Apply
If there is no Mode at
Insert disk
Browse
" , "
Monitor
Display a list of the known drivers for this device so that I can choose a
Browse Open
Finish
" , "
Settings Monitor
Change Specify the location of the driver Display a list of all the driver in a specific location..
Have Disk
button if you see the screen working normally after clicking
" button on the "
Setting
Settings
" and then click on "
" then click "
" button, then click "OK" button.
" button then the "
Setting
Display
" , "
Control Panel
Display
".
" button then choose A:(D:\Driver).
Digital Signature Not Found
" button in the "
" Icon.
" tab and then click "
Next
" button then the "
" , "
Control Panel
" icon.
" tab and click "
" tab.
" button
" and choose the monitor that corresponds to the one you
Close
" button and "OK" button until you close the Display Properties
File Needed
Update Driver..
" and then click "
Monitor Type
" window.
" window.
".
Advanced..
" then click on the "Next" button.
" button then click "
Next
Close
" button.
" button.
".
Advanced Properties
" area.
".
, and then double-click
, select the level of resolution and vertical
".
Have disk
" window then click the "
".
Next
" button.
" then click "
Display
" button.
icon.
Test
"button.
Yes
" button.
Next
All Display
. If the screen is
PDF created with pdfFactory Pro trial version www.pdffactory.com
2008/3/4file://D:\Berry\(D-drive)\My poject\三星\2220LM\2220LM CD Manual\2220LM CD Manual\manual\eng\01_htm\03.htm
Page 30
frequency by referring to the Preset Timing Modes in the user guide.
Window, you need to make the X86Config file, which is a type of system setting file.
Execute
To execute X-
Linux Operating System
1.Press Enter at the first and the second screen after executing the X86Config file.
2.The third screen is for
3.Set a mouse for your computer.
4.The next screen is for
5.Set a Keyboard for your computer.
6.The next screen is for
7.First of all, set a directly.)
8.Set a
9.Enter the of X-Window.
10.You have
vertical frequency
setting your mouse selecting a keyboard setting your monitor
horizontal frequency
for your monitor. (You can enter the frequency directly.)
model name of your monitor
finished
X-Window after setting other requested hardware.
setting up your monitor.
.
.
.
for your monitor. (You can enter the frequency
. This information will not affect the actual execution
Page 31
Model
SyncMaster 2220LM
[MENU/
1.
]
[ ] These buttons allow you to adjust items in the menu.
2.
[ ] Press this button to activate a highlighted menu item.
3.
4.
[
AUTO
Opens the on-screen menu and exits from the menu or closes the adjustment menu.
Press to self-adjust the incoming PC signal automatically.
]
The values of fine,coarse and position are adjusted automatically.
Page 32
When pressing the AUTO button after locking the OSD
AUTO
Menu Description
AUTO
When the ' as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only)
To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
- If auto adjustment does not work properly, press AUTO button again to adjust picture with more accuracy.
- If you change resolution in the control panel, auto function will be executed automatically.
AUTO
OSD Lock & Unlock
' button is pressed, the Auto Adjustment screen appears
Page 33
When pressing the MENU button after locking the OSD
Menu Description
This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings.
Page 34
OSD Lock & Unlock
: Hold down the menu button for more than five seconds to activate
Lock
the OSD adjustment lock function.
Unlock
deactivate the OSD adjustment lock function.
: Hold down the menu button for more than five seconds to
Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust MagicBright ( )
using the Direct button.
MagicBright
Menu Description
Push the MagicBright button to circle through available preconfigured
MagicBright
Volume
modes.
- Six different modes (Custom/Text/Internet/Game/Sport/Movie)
Page 35
Menu Description
Picture Color Image OSD Setup Information
Volume
Brightness Contrast Color Tone Color Control Gamma Coarse Fine Sharpness H-Position V-Position Language H-Position V-Position Transparency Display Time Image Reset Color Reset
Picture
When OSD is not on the screen, push the button to adjust volume.
Page 36
Menu Description Play/Stop
You can use the on-screen menus to change the
Brightness
brightness according to personal preference.
[MENU→ → , → MENU]
You can use the on-screen menus to change the contrast
Contrast
according to personal preference.
[MENU , → , → MENU]
Color
Page 37
Menu Description Play/Stop
The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom.
-Makes whites bluish.
-Keeps whites white.
-Makes whites reddish.
-Select this mode when you want to adjust
Color Tone
Cool Normal Warm Custom
the image according to your preferences.
[MENU , → , → MENU]
Adjusts individual R,G,B color balance.
Color Control
[MENU , → , → , → , → MENU]
Gamma correction changes the luminance of the colors with intermediate luminance.
l
Gamma
Mode 1
l
Mode 2
l
Mode 3
Image
[MENU , → , → , → MENU]
Page 38
Menu Description Play/Stop
Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may
Coarse
relocate it to the center using the horizontal control menu. (Available in analog mode only)
[MENU , → , → MENU]
Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the
Fine
frequency (clock speed). (Available in analog mode only)
[MENU , → , → , → MENU]
Changes the clearance of image.
Sharpness
[MENU , → , → , → MENU]
Changes the horizontal position of the monitor's entire display.
H-Position
(Available in analog mode only)
[MENU , → , → , → MENU]
V-Position
Changes the vertical position of the monitor's entire display. (Available in analog mode only)
[MENU , → , → , → MENU]
Page 39
OSD
Menu Description Play/Stop
You can choose one of 9 languages.
Language
:The language chosen affects only the language of
Note
the OSD. It has no effect on any software running on the computer.
[MENU , → , → MENU]
You can change the horizontal position where the OSD
H-Position
menu appears on your monitor.
[MENU , → , → , → MENU]
You can change the vertical position where the OSD menu
V-Position
appears on your monitor.
[MENU , → , → , → MENU]
Change the transparency of the background of the OSD.
Transparency
[MENU , → , → , → MENU]
The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it
Page 40
Display Time
is turned off. 5 sec, 10 sec, 20 sec, 200 sec
[MENU , → , → , → MENU]
Setup
Menu Description Play/Stop
Image parameters are replaced with the factory default
Image Reset
values.
[MENU , → , → , → MENU]
Color parameters are replaced with the factory default
Color Reset
values.
[MENU , → , → , → MENU]
Information
Page 41
Menu Description
Shows a video source, display mode on the OSD screen.
Information
[MENU , → MENU]
Page 42
Before calling for service, check the information in this section to see if you can remedy any
Model
SyncMaster 2220LM
Check List
problems yourself. If you do need assistance, please call the phone number on the
Information section or contact your dealer.
Symptom Check List Solutions
No images on the screen. I cannot turn on the monitor.
Is the power cord connected properly?
Can you see on the screen?
If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.
"Check Signal Cable"
Check the power cord connection and supply.
(Connected using the D-sub cable)
Check the signal cable connection. If the initial screen (the login screen)
appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes)
Note: If the initial screen (the login screen) does not appear, contact
the Service Center or your dealer.
Can you see
Mode","Recommended Mode 1680 x 1050 60Hz"
"Not Optimum
on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.
Adjust the maximum resolution and
Page 43
frequency that the monitor can handle properly.
If the display exceeds SXGA or 75 Hz, a
Mode","Recommended mode 1680 x 1050 60 Hz"
displayed. If the display exceeds 85 Hz, the display will work properly but the
Mode","Recommended Mode 1680 x 1050 60 Hz"
appears for one minute and then disappears. Please change to the recommended mode during this one-minute period.
(The message is displayed again if the system is rebooted.)
"Not Optimum
message is
"Not Optimum
message
I cannot see the On Screen Display.
The screen shows strange colors or just black and white.
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals?
Have you locked the On Screen Display (OSD) Menu to prevent changes?
Is the screen displaying only one color as if looking at the screen through a cellophane paper?
Have the screen colors become strange after running a program or due to a crash between applications?
The monitor is in PowerSaver mode. press a key on the keyboard to
activate the monitor and restore the image on the screen.
If there is still no image, press the ' ' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
Unlock the OSD by pressing the [MENU / ] button for at least 5 seconds.
Check the signal cable connection.Make sure the video card is fully inserted in it's slot.
Reboot the computer.
Has the video card been set properly?
The screen suddenly has become unbalanced.
The screen is out of focus or OSD cannot
Have you changed the video card or the driver?
Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD.
Have you adjusted the resolution or frequency on the monitor?
Set the video card by referring to the video card manual.
Adjust screen image position and size using the OSD.
Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
Adjust the resolution and frequency of the video card.
Page 44
be adjusted. (Refer to the Preset Timing Modes). LED is blinking but no
images on the screen.
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Is the frequency properly adjusted when checking the Display Timing on the menu?
Have the Windows colors been set properly?
Has the video card been set properly?
Have you installed the monitor driver?
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes.
(The maximum frequency per resolution may differ from product to product.)
Windows ME/2000/XP: Set the colors properly at the
Control Panel → Display → Settings
Set the video card by referring to the video card manual.
Install the monitor driver according to the Driver Installation Instructions.
Install the monitor driver according to the Driver Installation Instructions.
.
Problems related to Audio
Check the following items if there is trouble with the monitor.
1.Check if the power cord and the video cables are properly connected to the computer.
2.Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.)
3.If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver.
4.Check if the scanning ratio of the video screen is set at 56 Hz ~ 75 Hz. (Do not exceed 60 Hz when using the maximum resolution.)
5.If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "
then reboot the computer to reinstall the adapter (video) driver.
No sound Ensure that the audio cable is firmly
connected to both the audio-in port on your monitor and the audio-out port on your sound card. (Refer to Connecting the Monitor)
Check the volume level.
Sound level is too low. Check the volume level.
If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.
Control Panel → System → Device Administrator
" and
If problems repeatedly occur, contact an authorized service center.
Page 45
Your monitor provides a self test feature that allows you to check whether your monitor is
Q & A
Question
How can I change the frequency?
How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control
How can I set the Power Saving function?
How can I clean the outer case/LCD Panel?
Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version
of the driver used. (Refer to the computer or the video card manual for details.)
Panel→Display→Settings. * Contact the video card manufacturer for details.
Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual).
Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.
Answer
Self-Test Feature Check
Self-Test Feature Check | Warning Messages | Environment | Useful Tips
functioning properly.
Self-Test Feature Check
1.Turn off both your computer and the monitor.
2.Unplug the video cable from the back of the computer.
3.Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
This box appears during normal operation if the video cable becomes disconnected or damaged.
Page 46
4.Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
1.If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
2.Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
Useful Tips
l
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
l
Judging the monitor's working condition
If there is no image on the screen or a
1050 60 Hz"
message comes up, disconnect the cable from the computer while the monitor is
"Not Optimum Mode","Recommended Mode 1680 X
still powered on.
¡
If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition.
¡
In this case, check the computer for trouble.
Page 47
Model
SyncMaster 2220LM
General
General
Model Name SyncMaster 2220LM
LCD Panel
Size 22" Wide Diagonal (55.9 cm) Display area 473.76 mm(H) x 296.1 mm(V) Pixel Pitch 0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal 30 ~ 81 kHz Vertical 56 Hz ~ 75 Hz
Display Color
16.7 M
Resolution
Optimum resolution 1680 x 1050 @ 60 Hz Maximum resolution 1680 x 1050 @ 60 Hz
Input Signal, Terminated
RGB Analog.
0.7 Vp-p ± 5 % separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
Page 48
150 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz
Signal Cable
15pin-to-15pin D-sub cable, Detachable
Dimensions (WxHxD) / Weigh
517.26 X 362.48 X 61.56 mm / 20.4 x 14.3 x 2.4 inch (Without Stand)
517.26 X 424.38 X 207.83 mm / 20.4 x 16.7 x 8.2 inch (With Stand) / 5.1 kg / 11.2 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Max internal speaker
2 W
Environmental considerations
Operating Temperature : 14 °F~104 °F (-10 ~ 40 )
Humidity : 20% ~ 80%, non-condensing
Storage Temperature : -4 °F~140 °F (-20 ~ 60 )
Humidity: 10 % ~ 80 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness.
l
For example, the number of TFT LCD sub pixels that is contained in this product are 3,888,000.
Note: Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas.
(Class B equipment emits less electromagnetic waves than Class A equipment.)
PowerSaver
Page 49
This monitor has a built-in power management system called PowerSaver. This system saves energy
time. The monitor automatically returns to normal operation when you press a key on the keyboard. For
by switching your monitor into a low-power mode when it has not been used for a certain amount of energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature.
Power off
State
Power Indicator Blue Blue blinking Off
Normal Operation
Power saving mode
(Power button OFF)
EPA/ENERGY 2000
Power Consumption Less than 55 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Less than
1 watts
Less than
1 watts
Table 1. Preset Timing Modes
Horizontal
Display Mode
IBM. 640 x 350 31.469 70.086 25.175 +/­IBM. 640 x 480 31.469 59.940 25.175 -/-
IBM. 720 x 400 31.469 70.087 28.322 -/+ MAC. 640 x 480 35.000 66.667 30.240 -/­MAC. 832 x 624 49.726 74.551 57.284 -/-
MAC. 1152 x 870 68.681 75.062 100.000 -/­VESA. 640 x 480 31.469 59.940 25.175 -/­VESA. 640 x 480 37.861 72.809 31.500 -/­VESA. 640 x 480 37.500 75.000 31.500 -/-
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Page 50
VESA. 800 x 600 35.156 56.250 36.000 +/+ VESA. 800 x 600 37.879 60.317 40.000 +/+ VESA. 800 x 600 48.077 72.188 50.000 +/+
VESA. 800 x 600 46.875 75.000 49.500 +/+ VESA. 1024 x 768 48.363 60.004 65.000 -/­VESA. 1024 x 768 56.476 70.069 75.000 -/­VESA. 1024 x 768 60.023 75.029 78.750 +/+ VESA. 1152 x 864 67.500 75.000 108.000 +/+
VESA.1280 x 960 60.000 60.000 108.000 +/+
VESA.1280 x 1024 79.976 75.025 135.000 +/+
VESA. 1440 x 900 55.935 59.887 106.500 -/+
VESA.1680 x 1050 65.29 59.954 146.26 -/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Page 51
Model
SyncMaster 2220LM
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx
ARGENTINE 0800-333-3733 http://www.samsung.com/ar
North America
Latin America
BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl COLOMBIA 01-8000112112 http://www.samsung.com.co COSTA RICA 0-800-507-7267 http://www.samsung.com/latin ECUADOR 1-800-10-7267 http://www.samsung.com/latin EL SALVADOR 800-6225 http://www.samsung.com/latin GUATEMALA 1-800-299-0013 http://www.samsung.com/latin JAMAICA 1-800-234-7267 http://www.samsung.com/latin
Page 52
PANAMA 800-7267 http://www.samsung.com/latin PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin TRINIDAD & TOBAGO 1-800-7267-864 http://www.samsung.com/latin VENEZUELA 0-800-100-5303 http://www.samsung.com/latin
Europe
BELGIUM 02 201 2418 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz
DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi
FRANCE
GERMANY 01805 - 121213 ( 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.lu
3260 SAMSUNG(7267864) ( 0,15/min)
http://www.samsung.com/fr
NETHERLANDS 0900 20 200 88 ( 0,10/Min) http://www.samsung.com/nl NORWAY 815-56 480 http://www.samsung.com/no POLAND 0 801 801 881 http://www.samsung.com/pl PORTUGAL 80 8 200 128 http://www.samsung.com/pt REPUBLIC OF IRELAND 0818 717 100 http://www.samsung.com/uk SLOVAKIA 0800-SAMSUNG (7267864) http://www.samsung.com/sk SPAIN 902 10 11 30 http://www.samsung.com/es SWEDEN 0771-400 200 http://www.samsung.com/se SWITZERLAND 0800-7267864 http://www.samsung.com/ch U.K 0870 SAMSUNG (7267864) http://www.samsung.com/uk
CIS
ESTONIA 800-7267 http://www.samsung.ee LATVIA 800-7267 http://www.samsung.com/lv
Page 53
LITHUANIA 8-800-77777 http://www.samsung.lt
The screen must be redrawn several times per second in order to create and display an image
KAZAKHSTAN 8 800 080 1188 http://www.samsung.kz RUSSIA 8-800-200-0400 http://www.samsung.ru UKRAINE 8-800-502-0000 http://www.samsung.com/ur UZBEKISTAN 140-1234 http://www.samsung.uz
Asia Pacific
AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn HONG KONG 3698-4698 http://www.samsung.com/hk INDIA 3030 8282, 1800 1100 11 http://www.samsung.com/in INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za
U.A.E
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
800SAMSUNG (7267864) 8000-4726
http://www.samsung.com/mea
Vertical Frequency
Page 54
for the user. The frequency of this repetition per second is called Vertical Frequency or
Example :
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
Refresh Rate. Unit: Hz Example :If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen.
If the resolution is 1680 x 1050 , this means the screen is composed of 1680 horizontal dots (horizontal resolution) and 1050 vertical lines (vertical resolution).
For Better Display
1.Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD.
¡
Resolution: 1680 x 1050
¡
Vertical frequency (refresh rate): 60 Hz
2. 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness.
¡
For example, the number of TFT LCD sub pixels that is contained in this product are 3,888,000.
3.When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly. If excessive force is applied, you can have a stain on it.
4.If you are not satisfied with the quality of the picture, you can get better quality of the picture
Page 55
by executing "auto adjustment function" in display screen that is appeared as window
Change the mode to energy save or set a screensaver to move the picture when you need to
termination button is pressed. If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.
5.If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
be away from the monitor for an extended period of time.
Authority
Information in this document is subject to change without notice. © 2007 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
Page 56
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Loading...