Samsung SV-DVD540V User Manual

PAL

www.samsungvcr.com

AUX

OPEN/CLOSE

STANDBY/ON

OK

DVD-VCR

SV-DVD440
SV-DVD540
SV-DVD545

Remote Control Overview

(SV-DVD440)(SV-DVD540/SV-DVD545)

STANDBY/ON

OPEN/CLOSE

STANDBY/ON

OPEN/CLOSE

OK

OK

Contents

 Foreword

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .

3

Disc Type and Characteristics . . . . . . . . . . . . . .

4

 DVD-VCR Overviews

Front View of the DVD-VCR . . . . . . . . . . . . . . .

5

Rear View of the DVD-VCR . . . . . . . . . . . . . . . .

6

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6

Display Indicators . . . . . . . . . . . . . . . . . . . . . . .

7

 Connecting Your DVD-VCR

Inserting Batteries in the Remote Control . . . . . .

7
Connecting DVD-VCR to the TV using the Coaxial

Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7
Connecting DVD-VCR to the TV using the SCART

Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8
Connecting DVD-VCR to a Satellite Receiver or

Other Equipment . . . . . . . . . . . . . . . . . . . . . . . .

8

Plug & Auto Set Up . . . . . . . . . . . . . . . . . . . . . . 9

Tuning Your Television for the DVD-VCR . . . . . .

10

Setting the Date and Time . . . . . . . . . . . . . . . . .

10

Menu Language . . . . . . . . . . . . . . . . . . . . . . . .

11

 Setting Up Your DVD-VCR

Presetting the Stations Automatically . . . . . . . . .

11

Presetting the Stations Manually . . . . . . . . . . . .

12

Clearing a Preset Station . . . . . . . . . . . . . . . . . .

13

Changing the Preset Station Table . . . . . . . . . . .

14

Selecting the RF OUT Sound Mode (B/G-D/K) . .

14

Setting the DVD-VCR Output Channel . . . . . . . .

15

Selecting the Colour Mode . . . . . . . . . . . . . . . .

15

NICAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16

Intelligent Picture Control . . . . . . . . . . . . . . . . . .

16

ShowView Extend

★

(SV-DVD540/SV-DVD545 Only) . . . . . . . . . . .

17

Auto Power off . . . . . . . . . . . . . . . . . . . . . . . . .

17

Screen Messages . . . . . . . . . . . . . . . . . . . . . . .

17

Selecting the Cassette Type . . . . . . . . . . . . . . .

18

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . .

18

 Recording Television Broadcasts

Selecting the Recording Speed . . . . . . . . . . . . .

18

Protecting a Recorded Cassette . . . . . . . . . . . .

18

Recording a Programme Immediately . . . . . . . .

19

Recording a Programme with Automatic Stop . .

19

Using the ShowView Feature

★

(SV-DVD540/SV-DVD545 Only) . . . . . . . . . . .

20

Modifying ShowView Programming

★

(SV-DVD540/SV-DVD545 Only) . . . . . . . . . . .

21

Using the Timer Programming Feature . . . . . . .

22

Checking a Preset Recording . . . . . . . . . . . . . .

22

Cancelling a Preset Recording . . . . . . . . . . . . .

23

 Playing Back

Playing a Cassette . . . . . . . . . . . . . . . . . . . . . .

23

Adjusting Picture Alignment Manually . . . . . . . .

23

Selecting the Audio Output Mode . . . . . . . . . . . .

23

Playing a Cassette in Slow Motion . . . . . . . . . . .

24

Playing a Sequence Frame by Frame . . . . . . . .

24

Playing a Sequence at Variable Speeds . . . . . .

24

Searching for a Specific Sequence . . . . . . . . . .

25

Using the Tape Counter . . . . . . . . . . . . . . . . . . .

26

Connecting an RCAAudio/Video Input Cable

★

(SV-DVD440/SV-DVD540 Only) . . . . . . . . . . .

27

Using the Assemble Edit Function . . . . . . . . . . .

27

Recording from Another VCR or Camcorder . . .

28

Using the TV Buttons on the Remote Control

★

(SV-DVD540 /SV-DVD545 Only) . . . . . . . . . . .

28

 DVD Functions

Choosing a Connection . . . . . . . . . . . . . . . . . . .

29

Setting Up the Language Features . . . . . . . . . .

29

Setting Up the Audio Options . . . . . . . . . . . . . . .

31

Setting Up the Display Options . . . . . . . . . . . . .

32

Setting Up the Parental Control . . . . . . . . . . . . .

33

A/V Receiver Connections . . . . . . . . . . . . . . . . .

34

Special Playback Features . . . . . . . . . . . . . . . .

34

Adjusting the Aspect Ratio (EZ View) . . . . . . . . .

35

Using the Display Function . . . . . . . . . . . . . . . .

36

Changing the Camera Angle . . . . . . . . . . . . . . .

37

Selecting the Subtitle Language . . . . . . . . . . . .

37

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . .

38

Selecting the Audio Language . . . . . . . . . . . . . .

38

Using the Mark Function . . . . . . . . . . . . . . . . . .

39

MP3/WMA Play . . . . . . . . . . . . . . . . . . . . . . . . .

39

Program Play & Random Play . . . . . . . . . . . . . .

41

Picture CD Playback . . . . . . . . . . . . . . . . . . . . .

41

 Solving Problems

Technical Specifications . . . . . . . . . . . . . . . . . . .

43

Problems and Solutions (VCR) . . . . . . . . . . . . .

44

Troubleshooting Guide (DVD) . . . . . . . . . . . . . .

45

ENG-2

ENG-3

Safety Instructions

The following illustrations represent precautions.

The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.

DO NOT OPEN THE DVD-VCR. Refer to service personnel.

Do NOT expose the DVD-VCR to
extreme temperature conditions
(below 5°C and above 40°C) or to
extreme humidity conditions (less
than 10% and more than 75%).

Do NOT expose the DVD-VCR to
direct sunlight.

Do NOT expose the DVD-VCR to
any liquids.

Do NOT place any objects on the
DVD-VCR or remote control.

During a storm and/or lightning,
unplug the DVD-VCR from the
mains socket and aerial.

If the remote control is not used for
a long period of time, remove the
batteries and store it in a cool, dry
place.

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL

ENVIRONMENTS

This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners.
Use of this copyright protection technology must by authorized by Macrovision Corporized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is prohibited.

10% 75%

HH

40°C

5°C

ENG-4

Disc Type and Characteristics

Disc Markings

Play Region Number

~

DIGITAL

SOUND

STEREO

NTSC

• Play Region Number

• NTSC broadcast system in U.S.A, Canada,

Korea, Japan, etc.

PAL

• PALcolour system in Australia, Newzealand, etc.

• Dolby Digital disc

• Stereo disc

• Digital Audio disc

• DTS disc

Both the DVD player and the discs are coded by
region. These regional codes must match in order for
the disc to play. If the codes do not match, the disc
will not play.

The Region Number for this player is described
on the rear panel of the player.

Disc Types (Logos)

Recording Types

Disc Size Max. Playing Time Characteristics

12 Cm

8 Cm

Single-sided 240 min.
Double-sided 480 min.

Single-sided 80 min.
Double-sided 160 min.

Audio

+

Video

AUDIO-CD

DVD

•

DVD contains excellent sound and video
due to Dolby Digital and MPEG-2 system.

•

Various screen and audio functions can
be easily selected through the on-screen
menu.

74 min.

20 min.

12 Cm

8 Cm

Audio

•

An LP is recorded as an analog signal
with more distortion. CD is recorded as a
Digital Signal with better audio quality,
less distortion and less deterioration of
audio quality over time.

* DO NOT play CD-ROM, CD-I and DVD-ROM in this player!

(CDGs play audio only, not graphics.)

* It may not be to play CD-R,CD-RW and DVD-R in all cases due to the type of disc or condition of the recording.

This DVD player is capable of playing the following types of discs with the corresponding logos :

ENG-5

Front View of the DVD-VCR

1 2 3 4

5 6 7 8 9 10 11 12 13 14

1 DVD DECK
2 OPEN/CLOSE BUTTON
3 VIDEO CASSETE COMPARTMENT
4 EJECT BUTTON
5 STANDBY/ON BUTTON
6 REW/SKIP BACK BUTTON

7 STOP BUTTON
8 PLAY/STILLBUTTON
9 F.F / SKIP NEXT BUTTON
10 RECORD BUTTON
11 EZ VIEW BUTTON
12 PROGRAME SELECTION BUTTON

13 DVD SELECTBUTTON
14 VCR SELECTBUTTON
15 AUX VIDEO INPUTJACK
16 AUX AUDIO L, R INPUT JACK

1 DVD DECK
2 OPEN/CLOSE BUTTON
3 VIDEO CASSETE COMPARTMENT
4 EJECT BUTTON
5 STANDBY/ON BUTTON

6 REW/SKIP BACK BUTTON
7 STOP BUTTON
8 PLAY/STILLBUTTON
9 F.F / SKIP NEXT BUTTON
10 RECORD BUTTON

11 EZ VIEW BUTTON
12 PROGRAME SELECTION BUTTON
13 DVD SELECTBUTTON
14 VCR SELECTBUTTON

AUX

1 2 3 4

5 6 7 8 9 10 11 12 13 14 15 16

(SV-DVD545)

(SV-DVD440/SV-DVD540)

ENG-6

Rear View of the DVD-VCR

You have just purchased a SAMSUNG Video Cassette Recorder (DVD-VCR).
Together with your DVD-VCR, you will find the following accessories in the box.

Accessories

O
P
E
N
/

C
L
O
S
E

S
T
A
N
D
B

Y
/
O
N

REMOTE CONTROL

& BATTERIES

AUDIO & VIDEO

CABLE

OWNER’S

INSTRUCTIONS

COAXIAL CABLE

(SV-DVD540/SV-DVD545)

1 AUDIO L, R OUT SOCKETS
2 AERIAL IN CONNECTOR
3 AV2 (DEC./EXT.) SCART

(EURO-21) SOCKET

4 AUDIO L, R OUT SOCKETS

(DVD ONLY)

5 VIDEO OUT SOCKET
6 OUT TO TV CONNECTOR
7 AV1 (EURO AV) IN/OUT SCART

(EURO-21) SOCKET

8 DIGITALAUDIO OUT SOCKET

(COAXIAL)

9 DIGITALAUDIO OUT SOCKET

(OPTICAL)

★

(SV-DVD540/SV-DVD545)

10 S-VIDEO OUT JACK

5 6 7 8 9 10

1 2 3 4

(SV-DVD440)

1 AUDIO OUT SOCKETS
2 AERIAL IN CONNECTOR
3 AV2 (DEC./EXT.) SCART

(EURO-21) SOCKET

4 AUDIO L, R OUT SOCKETS

(DVD ONLY)

5 VIDEO OUT SOCKET
6 OUT TO TV CONNECTOR

7 AV1 (EURO AV) IN/OUT SCART

(EURO-21) SOCKET

8 DIGITALAUDIO OUT SOCKET

(COAXIAL)

9 S-VIDEO OUT JACK

5 6 7 8 9

1 2 3 4

LINE OUT

AUDIO

DIGITAL

S-VIDEO OUT

COAXIAL

AUDIO OUT

OPTICAL

ENG-7

Connecting DVD-VCR to the TV using the Coaxial Cable

To receive television programmes a signal must be
received from one of the following sources:

◆

An outdoor aerial

◆

An indoor aerial

◆

A cable television network

◆

A satellite receiver

☛

Make sure that both the television and the DVD­VCR are switched off before connecting the
cables.

1 Remove the aerial or network input cable from the

television.

2 Connect this cable to the 75Ω coaxial socket

marked on the rear of your DVD-VCR.

3 Plug the coaxial cable supplied into the socket

on your DVD-VCR.

4 Plug the other end of the coaxial cable into the

connector previously used for the aerial on the
television.

5 To obtain better quality pictures and sound on your

television, you can also connect your DVD-VCR to
the television via the SCART cable (see next page)
if your television is equipped with this type of
connection.

Inserting Batteries in the Remote Control

You must insert or replace the batteries in the remote
control when you:

◆

Purchase the DVD-VCR

◆

Find that the remote control is no longer
working correctly

1 Push the tab in the direction of the arrow to release

the battery compartment cover on the rear of the
remote control.

2 Insert two AAA, RO3 or equivalent batteries, taking

care to respect the polarities:

◆

+ on the battery with + on the remote control

◆

– on the battery with – on the remote control

3 Replace the cover by aligning it with the base of

the remote control and pushing it back into place.

➢

Do not mix different battery types (manganese
and alkaline for example).

1

Display Indicators

6

1 The DVD Deck is active
2 A DVD, CD or SVCD is loaded
3 The time, counter position, time remaining or

current deck status is displayed

4 VHS tape is inserted
5 The VCR Deck is active
6 ATimer Recording is programmed or in progress.

1 2 3 4 5

TV

2

4

3

TV

ENG-8

Connecting DVD-VCR to the TV using the SCART Cable

Connecting DVD-VCR to a Satellite Receiver or Other Equipment

You can connect your DVD-VCR to the television using
the SCART cable if the appropriate input is available on
the television. You thus:

◆

Obtain better quality sound and pictures

◆

Simplify the setting up procedure of your
DVD-VCR

☛

Regardless of the type of connection chosen, you
must always connect the coaxial cable supplied.
Otherwise, no picture will be visible on the
screen when the DVD-VCR is switched off.

☛

Make sure that both the television and the DVD­VCR are switched off before connecting the
cables.

1 Connect the coaxial cable as indicated on page 7.
2 Connect one end of the SCART cable to the AV1

(EURO AV) socket on the rear of the DVD-VCR.

3 Plug the other end into the appropriate connector

on the television.

You can connect your DVD-VCR to a Satellite receiver
or other DVD-VCR using the SCART cable if the
appropriate outputs are available on the equipment
chosen. The following illustrations give a few examples
of the connection possibilities.

1 AV1(EURO AV): By means of 21-pin Scart Cable

Plug the SCART Cable with satellite receiver or
other equipment into the AV1 (EURO AV) socket on
the rear of the DVD-VCR.
After making this connection, select the source by
pressing the INPUT SEL. button for the AV1 input
sources.

2 By means of RF Coaxial Cable

After making this connection, you must preset the
station received through the satellite tuner.
RF output channel of the satellite receiver should
be adjusted away from channel 36, which is used
by the DVD-VCR, e.g. re-adjust to channel 39.

SCART Cable

TV

RF coaxial cable

3

Aerial

2

SCART Cable

RF coaxial cable

Aerial

1

2

Satellite Receiver or other Equipment

Aerial Connector

TV

ENG-9

Plug & Auto Set up

Your DVD-VCR will automatically set itself up when it
is plugged into the mains for the first time. TV stations
will be stored in memory. The process takes a few
minutes. Your DVD-VCR will then be ready for use.

1 Connect the coaxial cable as indicated on page 7.

(Connecting Your DVD-VCR to the TV Using the
Coaxial Cable)

2 Plug the DVD-VCR into the mains.

Result : The Language Set menu is displayed.

3 Select the required language by pressing the

or❷

buttons.

4 Press OK to store the language selected.

Result: A message appears.

5 Press OK button.
6 Press OK to start the auto scanning.

◆

The number of stations automatically stored by
the VCR depends on the number of stations
that it has found.

7 The current time and date are displayed

automatically.
Check the date and time.
if it is :

◆

Correct, Press RETURN button twice to exit the
menu.

◆

incorrect, see page 10.

➢

Auto preset can be performed by pressing ■on
the VCR continuously for 5 seconds or more
with no tape inserted.

1 AV2 IN: By means of 21-pin Scart Cable

Plug the SCART Cable with satellite receiver or
other equipment into the AV2 (DEC./EXT.) socket
on the rear of the DVD-VCR.
After making this connection, select the source by
pressing the INPUT SEL. button for the AV2 input
sources.

2 By means of RF Coaxial Cable

After making this connection, you must preset the
station received through the satellite tuner.
RF output channel of the satellite receiver should
be adjusted away from channel 36, which is used
by the DVD-VCR, e.g. re-adjust to channel 39.

SCART Cable

RF coaxial cable

Aerial

1

2

Satellite Receiver or other Equipment

Aerial Connector

TV

Auto setup

Please wait

00 %

Clock Set

Time Date Year
12 : 00 1 / JAN / 2004 THU

ENG-10

Setting the Date and Time

Your DVD-VCR contains a 24-hour clock and calendar
used to:

◆

Automatically stop programme recording

◆

Preset your DVD-VCR to record a programme
automatically

You must set the date and time when:

◆

You purchase the DVD-VCR

☛

◆

The time and date are set automatically
from the broadcast signal. If the signal is
weak or ghosting occurs, the time and
date may not be set automatically.
In this case, they should be set manually.

◆

Do not forget to reset the time when you
change clocks from winter to summer
time and vice versa.

1 After pressing the MENU, press the OK or

❿

.

Result: The Setup menu is displayed.

2 Press the corresponding ,

❷

buttons to select

the Clock option.

3 Press the OK or

❿

to select this option.

Result: The Clock Set menu is displayed.

4 Press

➛

or ❿to select the hour, minutes, day,
month and year.
Result: The option selected highlight.

5 Press the or

❷

buttons to increase or decrease
the value.
Result:

The day of the week is displayed
automatically.

➢

You can hold the

or❷

buttons down to scroll

more quickly through the values.

6 On completion, press RETURN to exit the menu.

Tuning Your Television for the DVD-VCR

It is only necessary to tune your DVD-VCR if you are
not using a SCART.

➢

To view pictures from your DVD-VCR when a
Scart cable is used, the television must be set to
the audio/video mode (AV).

1 Switch on the television.
2 Switch on the DVD-VCR by pressing STANDBY/ON

on the front of the DVD-VCR or STANDBY/ON on
the remote control.

3 Select a programme position on the television to be

reserved for use with your DVD-VCR.

4 Insert the video cassette in the DVD-VCR. Check

that the DVD-VCR starts reading the cassette;
if not, press

❿

II

button.

5 Start a scan on your television or set the television

to UHF channel 36.

6 Fine tune the television until the pictures and sound

are obtained clearly.

7 If you cannot find the pictures and sound, or there

is interference from nearby channels, it may be
necessary to change the setting of the DVD-VCR
output channel (see Setting the DVD-VCR Output
Channel on page 15 and Problems and Solutions
on page 44).

8 When the picture and sound are perfectly clear,

store this channel at the desired programme
position on the television.
Result: That programme is now reserved for use

with your DVD-VCR.

Language : English

Install

User Set
Auto Power Off : Off
Screen Messages : On

Clock Set

Time Date Year
12 : 00 1 / JAN / 2004 THU

ENG-11

Setting the Menu Language

1 Open “MENU”

After pressing the MENU, press the OK or ❿.

2 Select “Language”

Use the

or❷

buttons to highlight Language,

then press the OK or ❿.

3 Set menu Language

Place the selection arrow next to your desired
Language, then press the OK button.

4 On completion, press RETURN to exit the menu.

Presetting the Stations Automatically

☛

You do not need to preset the stations if you

have already set them automatically (see Plug &
Auto Set Up on page 9).

Your DVD-VCR contains a built-in tuner used to receive
television broadcasts.

You must preset the stations received through the tuner.
This can be done:

◆

Plug & Auto Set up (see page 9)

◆

Automatically

◆

Manually (see page 12)

You can store up to 80 stations.

1 After pressing the MENU, press the OK or

❿

.

Result: The Setup menu is displayed.

2 Press the corresponding ,

❷

buttons to select

the Install option.

3 Press the OK or

❿

to select this option.

Result: The Install menu is displayed.

4 Press the corresponding or

❷

buttons, until the
Auto Setup is selected.
And then press the OK or ❿to select this option.
Result: A message appears, indicating that any

channels already preset on your DVD-VCR
will be deleted.

5 Press the or

❷

buttons to select your country.

☛

The VCR searches for the stations
according to a preset preference list
corresponding to the country that you have
selected.

Language : English

Install

User Set
Auto Power Off : Off
Screen Messages : On

English
Français
Deutsch
Español
Italiano
Nederlands

Language Set

Language : English

Install

User Set
Auto Power Off : Off
Screen Messages : On

Auto Setup

Manual Setup
TV System : K
VCR Output CH : CH 36

Install

ENG-12

Presetting the Stations Manually

☛

You do not need to preset the stations manually if

you have already set them automatically.

1 After pressing the MENU, press the OK or

❿

.

Result: The Setup menu is displayed.

2 Press the corresponding ,

❷

buttons to select the

Install option.

3 Press the OK or

❿

to select this option.

Result: The Install menu is displayed.

4 Press the corresponding or

❷

buttons, until the

Manual Setup option is selected.

5 Press the OK or

❿

to select a Manual Setup option.

Result: The TV STATION TABLE menu is displayed.

6 Press the or

❷

buttons to select a programme

number as required.

7 Press the

❿

button to preset the station.

Result: The MANUAL TUNING menu is displayed.

Result:◆The Please Wait indication highlight on

the television screen.

◆

The first frequency band is scanned and
the first station found is displayed and
stored.

◆

The DVD-VCR then searches for the
second station and so on.

◆

When the automatic scanning procedure
has finished, the DVD-VCR switches
automatically to programme 1.

➢

The number of stations automatically stored by
the DVD-VCR depends on the number of
stations that it has found.

8 If you wish to cancel the auto scanning before the

end, press the MENU button to exit the menu.

➢

◆

The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set
automatically. In this case, they should be set
manually (see page 10).

◆

Once the auto scanning procedure has finished,
some stations may have been stored more than
once; select the stations with the best reception
and delete the ones no longer required (see page

13).

6 Press OK button.

Result: A message appears, indicating that any

channels

7 Press OK to start the auto scanning.

Presetting the Stations Automatically

Auto Setup

Your data will be lost

Press OK to continue
Menu to exit

Auto Setup

Please Wait
15%

Auto Setup

Manual Setup
TV System : K
VCR Output CH : CH 36

Install

TV STATION TABLE

PR CH NAME DEC
1
2
3
4
5

SWAPPING : OK
DELETE : CLEAR RETURN

PR :
CH : - - -
MFT : ­DECODER : OFF
NAME : - - - -

MANUAL TUNING

MEMORY : OK

RETURN

ENG-13

8 Press the ➛or

❿

buttons to start scanning the
channels.
Result: The frequency band is scanned and the first

station found is displayed.

9 Press the

❷

button, until the DECODER is selected.

10 Press the

❿

button to activate or deactivate use of the

decoder for the TV station, if necessary.

11 Press the or

❷

buttons until the NAME is selected.
The station name is set automatically from the
broadcast signal.

12 To change the programme’s name, press the

❿

button.

Result: The first letter of the name flashes.

13 To... Then...

Select a character Press the

or❷

button until
the in the namerequired
character is displayed (letters,
numbers or “-” character).

Move to the next or

Press the

➛or❿

buttons

previous character

respectively.

14 If you... Then...

Wish to store the

◆

Press the

or❷

buttons

station displayed until the MFT is selected.

◆

Press the

➛or❿

buttons to

adjust the picture, if necessary.

◆

Press OK to store the station

Do not wish to

◆

Press the

or❷

buttons
store the station until the CH is selected.
displayed

◆

Press the

➛or❿

buttons to

go on scanning the

frequency band and display
the next station

◆

Go back to the beginning of

Step 14

15 Repeat this procedure from Step 6 onwards, until

all the required stations have been stored.

16 On completion, press the RETURN button three

times to exit the menu.

Clearing a Preset Station

☛

If you have stored a TV station:

◆

That you do not require

◆

At the wrong programme position

you can cancel it.

1 After pressing the MENU, press the OK or

❿

.

Result: The Setup menu is displayed.

2 Press the corresponding ,

❷

buttons to select

the Install option.

3 Press the OK or

❿

to select this option.

Result: The Install menu is displayed.

4 Press the corresponding or

❷

buttons, until the

Manual Setup option is selected.

5 Press the OK or

❿

to select a Manual Setup option.

Result: The TV STATION TABLE menu is displayed.

6 Press the corresponding or

❷

buttons, until the

required preset TV station (PR) is selected.

7 Press the CLEAR button.
8 Repeat the same procedure from Step 6 onwards

until all the required stations have been cleared.

9 On completion, press the RETURN button four

times to exit the menu.

Auto Setup

Manual Setup
TV System : K
VCR Output CH : CH 36

Install

TV STATION TABLE

PR CH NAME DEC
1 21
2
3
4
5

SWAPPING : OK
DELETE : CLEAR RETURN

- - - -

OFF

ENG-14

You can choose the sound mode (B/G or D/K)
according to the TV set connected to your VCR.

1 After pressing the MENU, press the OK or

❿

.

Result: The Setup menu is displayed.

2 Press the corresponding ,

❷

buttons to select

the Install option.

3 Press the OK or

❿

to select this option.

Result: The Install menu is displayed.

4 Press the OK or

❿

buttons, until the TV System

option is selected.

5 Press the OK or

❿

buttons to select G or K.

6 On completion, press RETURN to exit the menu.

Selecting the RF OUT Sound Mode (B/G-D/K)

Changing the Preset Station Table

You can rearrange the Station Table and give different
programme numbers to the stations listed according to
your own preferences.

1 After pressing the MENU, press the OK or

❿

.

Result: The Setup menu is displayed.

2 Press the corresponding ,

❷

buttons to select

the Install option.

3 Press the OK or

❿

buttons to select this option.

Result: The Install menu is displayed.

4 Press the corresponding or

❷

buttons, until the

Manual Setup option is selected.

5 Press the OK or

❿

button to select this option.

Result: The TV STATION TABLE menu is displayed.

6 Press the corresponding or

❷

buttons, until the
required preset TV programme is selected.
Result: The selected station is displayed at the

same time on the television screen.

7 To change the programme number assigned to a

station press the OK button on the remote control.
(For example, To move a TV station in programme
1 to programme 3)

8 Press the or

❷

buttons to select required
position. And then press OK again to swap the
position.

9 On completion, press the RETURN button four

times to exit the menu.

K
G

Auto Setup

Manual Setup
TV System : K
VCR Output CH : CH 36

Install

TV STATION TABLE

PR CH NAME DEC
1 21
2
3
4
5

SWAPPING : OK
DELETE : CLEAR RETURN

- - - -

OFF

Auto Setup

Manual Setup
TV System : K
VCR Output CH : CH 36

Install

TV STATION TABLE

PR CH NAME DEC
1
2
3 21
4
5

SWAPPING : OK
DELETE : CLEAR RETURN

- - - -

OFF