Samsung SVD-4120A, SVD-4120AW User Manual

Vandal-Proof Color Dome Camera

INSTRUCTION MANUAL

SVD-4120A/A W

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,
Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703

TEL: [phone]~41 FAX: [phone]

•

SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)

Samsung House, 1000 Hillswood Drive Hillswood Business
Park Chertsey Surrey KT16 OPS

TEL: [phone] FAX: [phone]

www.samsungtechwin.com
www.samsungcctv.com

•

SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)

Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,
U.S.A

TEL: [phone] FAX: [phone]

•

TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)

7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190

TEL: [phone] FAX: [phone]

P/No. : 6806-0458-01B

VAN 04. 10

SAMSUNG CCTV CAMERA

Thank you for purchasing a SAMSUNG CCTV CAMERA.
Before operating the camera, confirm the camera model and
proper input power voltage. In order that you can understand
this manual thoroughly, we'll introduce our model description.

SVD-4120A Series (410,000 pixels)

• NTSC models • PAL models
SVD-4120AN SVD-4120AP
SVD-4120AWN SVD-4120AWP

Model Description

SVD-4120A X X

Signal system

Lens Type

• Lens Type
Blank 2.5X, f=3.8~9.5 Vari-Focal Lens
W 2.4X, f=2.5~6.0 Vari-Focal Lens

• Signal System
N NTSC Model
P PAL Model

The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

INFORMATION-This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

WARNING -Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and

should conform to all local codes.

Features

Warning

Fine Picture Condition Under Very
Low Illumination (SENSE UP)

1/3 high density CCD and digital
processor permit high quality pictures to
be captured in very low light condition.

High Resolution

The horizontal resolution of 500TV lines
can be achieved by using a high density
CCD having Double Speed 410,000 pixels
SONY CCD, which provides clean,
noiseless and reliable pictures.

Auto Iris Vari-Focal Lens Built In

The focal length of lens is 3.8 to 9.5 mm,
equivalent to 2.5x zoom.(2.5 to 6.0mm,
equivalent to 2.4x zoom/SVD-4120AW)
The built-in lens allows the camera to
have a Wider Dynamic Range, therefore
you can use in various applications.

Wide Range ATW

The White Balance can be automatically
adjusted in response to light condition so
that you can observe in an appropriate
color balance.

IP66 Approved / Dust and Rain
Resistant

With dust and rain resistant design, the
camera can be installed outside under
building eaves or places that are exposed
to the dust and rain.

SSNR(Samsung Super Noise
Reduction) CHIP

SVD-4120A/AW has an assistant DSP
chip that can remove image noise
efficiently and it shows clean and obvious
image in low luminance

Electronic DAY/NIGHT

In normal or high luminance, camera
maintains color mode. On the contrary, it
get changed into B/W mode in low
luminance.

The camera needs periodic inspection.

Contact an authorized technician for inspection.

Stop using your camera when you find a malfunction.

If you use your camera around smoke or unusual heat for a long time, a fire may
be caused.

Do not Install the camera on a surface that can not support it.

Unless the surface is suitable, it could cause falling or other hazards.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not disassemble the camera.

It may result in fire, electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in fire or other hazards.

Contents

Precautions

Composition

Name and Function of Each Section

Connection

Connecting to Monitor
Connecting to Power

Operating Your Camera

Configuration of The Menu

8

10

11

13
13

14

15

Setting Up The Menu

• CAMERA ID

• BACKLIGHT

• WHITE BALANCE

• MOTION DETECTION

• IRIS LEVEL CONTROL

• SHUTTER SPEED CONTROL

• SESE UP

• GAIN

• SSNR

• SPECIAL

Troubleshooting

16
17
20
21
22
25
26
27
28
28
30

32

15

Dimention

Specifications

34

35

Precautions

Do not install the camera in
extreme temperature conditions.

Only use the camera under conditions
where temperatures are between -10˚C
and +50˚C. Be especially careful to provide
ventilation when operating under high
temperatures.

Do not install the camera under
unstable lighting conditions.

Severe lighting change or flicker can cause
the camera to work improperly.

Do not install or use the camera in an
environment where the humidity is high.

It can cause the image quality to be poor.

Do not touch the front lens of
the camera.

It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.

Do not drop the camera or
subject them to physical shocks.

It can cause malfunctions to occur.

Never keep the camera face to
strong light directly.

It can damage the CCD.

Do not expose the camera to
radioactivity.

If it is exposed to radioactivity, For
heated CCD, it will be out of order.

Notes

• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.

• Please check that the power satisfies the normal specification before connecting
the camera.

COLOR DOME CAMERACOLOR DOME CAMERA User’s ManualUser’s Manual

98

Composition

1. SVD-4120A/AW

2. Instruction Manual

3. Quick Install Guide

4. Wrench

5. Ø5 Tapping Screws 4EA

6. Template

Name and Function of Each Section

7. Video Output Cable for installer

COLOR DOME CAMERA User’s Manual

10

COLOR DOME CAMERA User’s Manual

11

Name and Function of Each Section

Connection

Pan Base

control panning angle of camera

Tilt Base Holding Serews

fix tilted position.

Pan Base Holding Screws (Color : Silver)

fix panned position

Zoom Handle

adjust zoom between WIDE and TELE

Focus Handle

after adjusting zoom, adjust focus

SET Button

confirm the status of the selected feature

RIGHT Button

move cursor to the right, change the status of the selected feature

DOWN Button

move cursor to the down, select the desired feature item

UP Button

move cursor to the up, select the desired feature item

LEFT Button

move cursor to the left, change the status of the selected feature

Video Output Terminal
Video Output Terminal to Monitor
Video Output Jack
Power Input Jack
Shield Case
Dome Cover

Connecting to Monitor

Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.

CCTV Camera Monitor

• As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.

• If necessary, you can connect the monitor to the REMOTE jack on the back of
your camera.

• Only connect the cable when the power is turned off.

• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.

Intermediate End monitor

CCTV Camera

COLOR DOME CAMERA User’s Manual

12

COLOR DOME CAMERA User’s Manual

13

Connection

Operating Your Camera

Connecting to Power

• Use AC 24V / 300mA or DC 12V / 500mA power source.

For DC Power Type

• For DC power as the voltage drop according to the length of the cable in the
above table, a camera may malfunction if there is an excessively long cable run.

Resistance of copper wire [at 20C˚ (68˚F)]

Copper wire size (AWG)
Resistance ( Ω / m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006

* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.

Notes

• Be sure to connect power only after all the installation is complete.

• Note that AC or DC adaptor is not supplied with camera.

• Use the UL listed, class 2 power transformer of AC 24V adaptor.

• Ground should be connected to the GND terminal.

2

#24(0.22mm

)#22(0.33mm2)#20(0.52mm2)#18 (0.83mm2)

Configuration of The Menu

SETUP MENU

CAMERA ID (see page 17)

• OFF • ON
BACKLIGHT (see page 20)

• WDR • BLC • OFF
WHITE BAL. (see page 21)

• W-ATW • S-ATW • AWC • MANUAL
MOTION DET. (see page 22)

• OFF • MD1 • MD2
IRIS LEVEL CONTROL (see page 25)

• LEVEL
SHUTTER (see page 26)

• OFF • 1/100 (1/120) • MANUAL
SENSE UP (see page 27)

• Auto • OFF
GAIN (see page 28)

• OFF • AGC-L • AGC-H
SSNR (see page 28)

• OFF • LOW • MIDDLE • HIGH
SPECIAL (see page 30)

• COLOR • SYNC • PRIVACY • RESET

• END • EXIT

EXIT

COLOR DOME CAMERA User’s Manual

14

COLOR DOME CAMERA User’s Manual

15

Operating Your Camera

Setting Up The Menu

Use the five SETUP MENU buttons on back of the camera.

LEFT button

UP button

DOWN button

RIGHT button

SET button

1. Press the SET button to access the SETUP mode.

• SETUP menu is displayed on the monitor screen.

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L
SSNR MIDDLE
SPECIAL
EXIT

2. Select the desired feature using the UP or DOWN button.

• Each time you press the UP or DOWN button, the arrow indicator moves up
or down.

• Move the arrow indicator to the desired feature item.

SETUP

Select the function using

the UP or DOWN button.

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L
SSNR MIDDLE
SPECIAL
EXIT

Change the status using
the LEFT or RIGHT button.

SETUP

3. Change the status of the selected feature using the LEFT or RIGHT button.

4. When completed, move the arrow indicator to 'EXIT' and press the SET button.

Notes

• For the mode with you can access submenu.

• You can access submenu using SET button.

CAMERA ID

If you enter a CAMERA ID, the name will be displayed in the screen monitor.

1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'CAMERA ID' using the UP or DOWN button.

2. Set 'CAMERA ID' to 'ON' using the LEFT or RIGHT button.

Notes

• If the CAMERA ID feature is set to 'OFF', the name
will not displayed in the monitor.

SETUP

CAMERA ID OFF
BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L
SSNR MIDDLE
SPECIAL
EXIT

COLOR DOME CAMERA User’s Manual

16

COLOR DOME CAMERA User’s Manual

17

Operating Your Camera

3. Press SET button.

CANERA ID

POS CLR RESET END

4. You can enter up to 16 characters.
Move the cursor to character-enter location by using the LEFT or RIGHT button.
Select the desired character by using UP or DOWN button.

•The factory defualt characters are A, B, ···, a, b, ···, ., -, ··· 0, 1···, 8, 9

CAMERA ID

POS CLR RESET END

Press the SET button to confirm the blinking character. The first character is
saved and the cursor in the bottom of the screen moves to the next position.

Repeats steps , and until you create the full name you want.

Notes

• If you make a mistake while entering name

Move the cursor to ‘CLR’, press ‘SET’ button.
After erasing the character from right to left, correct the character again.

5. Select the position at which the CAMERA ID will be located on the screen.
Move the cursor to 'POS' and press SET button.

CAMERA ID

POS CLR RESET END

The CAMERA ID is displayed on the bottom-left of the monitor screen.
(Default position)

FRONT DOOR

Select the position by using the 4-directional buttons, then press the SET
button to confirm the position.

FRONT DOOR

6. When completed, move the cursor to 'END' and press SET button.

COLOR DOME CAMERA User’s Manual

18

COLOR DOME CAMERA User’s Manual

19

Operating Your Camera

BACKLIGHT

SV-II DSP chip built-in provides intelligent light level control to overcome the
severe Backlight conditions.

1. Press the SET button to display the SETUP menu and move the arrow
indicator to ‘BACKLIGHT’ using the UP or DOWN button.

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW

2. SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.

WDR: In case that bright and dark parts exist on the screen at the same time,

your camera allows you to see both parts clearly

BLC: When the image is in front of strong background lighting, your camera

allows you to get the clear image

OFF: Deactivation

WDR BLC OFF

3. Press the ‘SET’ button.

• When ‘WDR’ is chosen, you can adjust the level.

You can select the level from -4 to 4. WDR sensitivity is increased or decreased.

SETUP

WDR SET

LEVEL 0

PRESS SET TO RETURN

4. When completed, press the SET button.

Notes

• If you select WDR mode, the following phenomenon may appear by lighting
condition. In these cases do not select WDR mode.

Unnatural color change or unnatural phenomenon on the screen
Noise of bright part on the screen

• According to the area of bright part on the screen there may be the difference of
WDR performance so be sure to adjust the degrees of the visual angle when
installing your camera.

• If you increase WDR level, unnatural phenomenon may appear.

WHITE BALANCE CONTROL

Your camera provides 4 ‘WHITE BAL.’ control modes. You can select the most
suitable one. You can adjust the white balance.

1. Press the SET button to display the SETUP menu and move the arrow indicator
to 'WHITE BALANCE' using the UP or DOWN button.

2. Set ‘WHITE BAL.’ to the desired mode using LEFT or RIGHT button.

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL

The six WHITE BALANCE control modes are as follows :

W-ATW(Wide Auto Tracking White balance):

When color temperature is 2400~12000K, select this mode. (EX. a fluorescent
lamp, outdoor)

SETUP

COLOR DOME CAMERA User’s Manual

20

COLOR DOME CAMERA User’s Manual

21

Operating Your Camera

S-ATW(Special Auto Tracking White balance): When color temperature is
1800~6000K, specially in sodium lamp, select this mode. (EX. sodium lamp,
inside the tunnel)

AWC(Auto White balance Control): The white balance is automatically
adjusted in a specific environment. In order to obtain the best result, press the SET
button while the camera focuses on white paper. If the environment including the
light source is changed, you have to adjust the white balance again.

MANUAL : To fine adjust, select the Manual mode. You can increase or
decrease the red or blue factor while monitoring the difference on the screen.
Set to 'MANUAL' mode and press the SET button. Increase or decrease the
value for RED(R-Gain) and BLUE(B-Gain), watching the color of the picture, and
press the SET button when you obtain the best color.

Notes

• Proper White Balance may not be obtained under the following conditions, in these
cases select the AWC mode.

When the scene contains mostly high color temperature object, such as a blue
sky or sunset.
When the scene is dim.
If your camera faces fluorescent lamp directly or is installed in the place of the
changing illumination.

MOTION DETECTION

Whenever your camera detects motion of object displaying ‘MOTION DETECTED’
with the number counted up on the screen.

1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'MOTION DET.' using the UP or DOWN button.

2. Set ‘MOTION DET.’ to the desired mode using LEFT or RIGHT button.

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF

SETUP

MD1:Your camera detects the object’s motion by outline or difference of a

color tone, so this mode is very useful for the daytime or observing
small moving object.

Press SET button.

Move the arrow indicator to ‘AREA SET’ using UP and DOWN button, and
then press the SET button.

Set the areas you want to observe.

· You can adjust the top, bottom, left and right base lines by 13 steps from top to
bottom, 18 steps from left to right with an increment of 1.

COLOR DOME CAMERA User’s Manual

22

COLOR DOME CAMERA User’s Manual

23

Operating Your Camera

· Move the arrow indicator to 'TOP' using the UP or DOWN button and increase or
decrease the value using the LEFT or RIGHT button. Repeat the procedure for
bottom, left and right.

18

Maximum

6

13

Minimum

5

· When completed, press SET button.

MD2:Your camera detects object’s motion by the variation of brightness, so

this mode is very useful for night or observing large moving object.
Also MD2 enables you to set seperated areas.

Press SET button.

Move the arrow indicator to ‘AREA SET’ like MD1.
Set the areas you want to observe of the 48 areas.

· Move the cursor to the area you want to observe, and then press the SET button.

· After setting, move the cursor to edge in any direction and then press the button
just one more, let ‘END’ blink.

· Press the SET button.

Notes

If you set some areas of 48 areas, your camera detects the object’s motion within

•
the areas you set.

Tips on Using the Motion Detection Feature

• As you increase or decrease MD LEVEL, the areas’ sensitivity is increased or
decreased for object.

• After selecting zone and sensitivity, perform a test operation to make sure it
works properly.

• If the lighting flickers, the motion detection feature might not work properly.

• The object should occupy 10% or more of its zone. The bigger the object, the
higher sensitivity.

• If the brightness of an object changes rapidly by sudden lighting change, the
camera may detect it as a motion.

• Your camera can count up to 999. If you reset your camera with selecting
‘RESET’ in SPECIAL menu or turn it off and on, your camera’ll count up from 0.

• When this feature is activated, another algorithm may take more time to be operated.

• This system does not guarantee prevention of fires or thefts. The manufacturer
is not responsible for any accident or damage.

IRIS LEVEL CONTROL

You can control the brightness of the screen.

1. Press the SET button to display the setup menu and move the arrow indicator
to 'IRIS' using the UP or DOWN button and press SET button.

2. Set ‘LEVEL’ to the desired brightness using LEFT or RIGHT button.

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF

3. When completed move the arrow indicator to ‘END’ and press the SET button.

SETUP

COLOR DOME CAMERA User’s Manual

24

COLOR DOME CAMERA User’s Manual

25

Operating Your Camera

SHUTTER SPEED CONTROL

You can control brightness of the screen by the shutter speed.

1. Press the SET button to display the setup menu and move the arrow indicator
to ‘SHUTTER’ using the UP or DOWN button.

2. Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT button.

OFF:Deactivation
1/100(1/120: PAL Models):Flickerless mode (When WDR is on, the image

MANUAL: When setting shutter speed manually

3. If you choose ‘MANUAL’, select the optimal shutter speed.

•You can select speed from ‘1/60’ to ‘1/200,000’sec (NTSC Models), ‘1/50’ to
‘1/200,000’sec (PAL Models).

•When the shutter speed is increased or decreased using the LEFT or RIGHT
button, you can find the difference by monitoring the brightness of the
screen.

MANUAL SET

VALUE : 1/60

PRESS SET TO RETURN

NTSC Models

can flicker a little)

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L

SETUP

PRESS SET TO RETURN

MANUAL SET

VALUE : 1/50

PAL Models

4. When completed, press the SET button.

Notes

• For effective 1/100(1/120) mode set WDR mode in BACKLIGHT menu to OFF.
1/100(1/120) mode is not effective with WDR mode.

• If you choose MANUAL mode, you can’t use WDR mode in ‘BACKLIGHT’ menu.

• If you select MANUAL mode, SENSE UP is not operated.

SENSE UP

You can always get the clear image with this function under night or low­lighting level.

1. Press the SET button to display the setup menu and move the arrow
indicator to 'SENSE UP' using the UP or DOWN button.

2. Set ‘SENSE UP’ to the desired mode using the LEFT or RIGHT button.

AUTO:When your camera is under night or low-lighting level, select this

mode.

OFF: Deactivation

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L
SSNR MIDDLE
SPECIAL
EXIT

SETUP

COLOR DOME CAMERA User’s Manual

26

COLOR DOME CAMERA User’s Manual

27

Operating Your Camera

GAIN

To get brighter picture.

1.Press the SET button to display the setup menu and move the arrow indicator
to ‘GAIN’ using the UP or DOWN button.

2. Set ‘gain’ to desired mode using the LEFT or RIGHT mode.

AGC-H: Gain is increased or decreased from 0 to 30dB automatically as

following the illumination.

AGC-L:Gain is increased or decreased from 0 to 27dB automatically as

following the illumination.

OFF: Deactivation

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L
SSNR MIDDLE
SPECIAL
EXIT

SETUP

SSNR(Samsung Super Noise Reduction)

To reduce the noise on the screen.

1.Press the SET button to display the setup menu and move the arrow indicator
to ‘SSNR’ using the UP or DOWN button.

2. Set ‘SSNR’ to desired mode using the LEFT or RIGHT mode.

LOW: low reduction of the noise

MIDDLE: middle reduction of the noise
HIGH: high reduction of the noise

OFF: Deactivation

CAMERA ID OFF

BACKLIGHT WDR
WHITE BAL. W-ATW
MOTION DET. OFF
IRIS LEVEL
SHUTTER OFF
SENSE UP OFF
GAIN AGC-L
SSNR MIDDLE
SPECIAL
EXIT

Notes

•If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is increased as well
as noise on the screen.

• Afterimage may appear with SSNR.

SETUP

COLOR DOME CAMERA User’s Manual

28

COLOR DOME CAMERA User’s Manual

29

Operating Your Camera

SPECIAL

1.Press the SET button to display the setup menu and move the arrow indicator to
‘SPECIAL’ using the UP or DOWN button.

2. Press the SET button.

COLOR : choose color or B/W mode

- ON : color mode

- OFF : B/W mode

- AUTO1 : generally color mode, B/W mode in low luminance.

- AUTO2 : AUTO2 is identical with AUTO1 under SENSE UP : AUTO condition.
SYNC :Two SYNCHRONIZATION modes are available INTERNAL and

EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronizes the
video signal between cameras without a synchronous generator.
The line-lock synchronization is only used in the areas of 60Hz
(NTSC Models) / 50Hz (PAL Models).

- INT : Internal synchronization

- OFF : External line-lock synchronization

· If you choose ‘L/L’, you can adjust the desired phase. Press the SET button.

-You can adjust the desired phase from 0 to 270.

LINE LOCK

PHASE : 225

PRESS SET TO RETURN

Notes

• When the power frequency is 50Hz, you can not use line-lock mode(NTSC Models).

• When the power frequency is 60Hz, you can not use the line-lock mode(PAL Models).

• ‘Sync.’ mode is fixed to ‘INT’ in DC 12V input power.

PRIVACY: To mask area which you want to mask

- OFF: Deactivation

- ON: Privacy mode activated

· Press the SET button.

· Move the arrow indicator to area you want to mask.

· Set ‘ON’ using LEFT or RIGHT button.

· Press the SET button and then set the area’s bounds with the method like
MD1 Set. (see page 23)

· When completed, press the SET button.

RESET: To reset your camera to factory default condition
END: To move Top-menu
EXIT: To finish setting menu

COLOR DOME CAMERA User’s Manual

30

COLOR DOME CAMERA User’s Manual

31

Troubleshooting

If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.

Problem

Nothing appears on
the screen.

The image on the
screen is dim.

The image on the
screen is dark.

The camera is not
working properly, and
the surface of the
camera is hot.

MOTION DETECTION
function is not active.

• Check that the power cord and line connection
between the camera and monitor are fixed properly.

• Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.

• Is lens stained with dirt? Clean your lens with soft,
clean cloth.

• Set the monitor to proper condition.

• If the camera is exposed to too strong light, change

the camera position.

• Adjust the lens’ focus properly.

• Adjust the contrast feature of the monitor.

• If you have an intermediate device, set the 75Ω / Hi-z

properly. (refer to page 13)

• Check that you have properly connected the camera
to an appropriate power source.

• Have you set ‘MOTION DET.’ menu to OFF?

• Have you set ‘MD LEVEL’ to too low?

• Have you set ‘MD AREA’ properly?

Solution

Problem

The color of the picture
is not matched.

The image on the screen
flickers.

L/L mode isn’t able to
be selected.

Solution

• Check that you have properly set the ‘WHITE BAL.’
menu. (refer to page 21)

• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.

• Have you connected your camera to DC power
source? Connect it to AC power source.

COLOR DOME CAMERA User’s Manual

32

COLOR DOME CAMERA User’s Manual

33

Dimension

Specifications

126mm

85mm

Ø 148mm

85mm

83.5mm

85mm

46mm

Item

Power Source
Power Consumption
Image Sensor
Total Pixels
Effective Pixels
LENS TYPE
Maximum Aperature Ratio
Angle of View
Scanning System

Synchronization
Video Output

Resolution
Wide Dynamic Range
Gain Control
Electric Shutter Speed
SENSE UP
IRIS MODE
WHITE BALANCE
Min. Illumination
S/N(Y signal)
Motion Detection
O.S.D
SSNR
PRIVACY Function
Operating Temperature
Operating Humidity
Dimension(mm)
Weight(W/O Lens & Power Cord)
Angle

SVD-4120AN SVD-4120AP SVD-4120AWN SVD-4120AWP

DC 12V / AC 24V compatible

280mA(DC) / 3.8W(AC)

811(H)x508(V), 1/3”CCD 759(H)x596(V), 1/3”CCD 811(H)x508(V), 1/3”CCD 759(H)x596(V), 1/3”CCD
768(H)x494(V), 1/3”CCD 752(H)x582(V), 1/3”CCD 768(H)x494(V), 1/3”CCD 752(H)x582(V), 1/3”CCD

H: 74.2˚~30.0˚, V: 54.0˚~22.4˚, D: 96.8˚~37.4˚ H: 108.2˚~47.6˚, V: 80.4˚~35.6˚, D:136.6˚~59.4˚

2:1 Interlaced 525

Lines/60Fields/30Frames

1.0V[p-p]NTSC composite,
75W/BNC Connector

1/60~1/200,000sec 1/50~1/200,000sec 1/60~1/200,000sec 1/50~1/200,000sec

1/3”, Vertical double density interline CCD

2.5X Vari-Focal,f=3.8~9.5 2.4X Vari-Focal,f=2.5~6.0
1:1.3~2.0 1:1.3~1.9

2:1 Interlaced 625

Lines/50Fields/25Frames

Internal / Line Lock selectable

1.0V[p-p]PAL composite,
75W/BNC Connector

AGC-L, AGC-H, OFF selectable

Built-in(selectable limit~X128)

W-ATW / S-ATW / AWC / MANUAL

0.003Lux(Sense Up) / 0.3Lux(F1.3)

LOW / MIDDLE / HIGH /OFF

ON / OFF(4 Programmable Zone)

-10˚C ~ +50˚C (14˚F ~ 122˚F)

Panning : 340˚ , Tilt : 70˚

* Design and specifications are subject to change without notice

2:1 Interlaced 525

Lines/60Fields/30Frames

1.0V[p-p]NTSC composite,
75W/BNC Connector

500TV Lines

ON / OFF / AUTO

DC Drive

50dB (Weight ON)
MD1 / MD2 / OFF

Built-in

30% ~ 90% RH

f150(W) x 130(H)

1.4kg

2:1 Interlaced 625

Lines/50Fields/25Frames

1.0V[p-p]PAL composite,
75W/BNC Connector

COLOR DOME CAMERA User’s Manual

34

COLOR DOME CAMERA User’s Manual

35

DECLARATION OF CONFORMITY

Application of Council Directive(s) 89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SVD-4120A/AW
Beginning Serial NO. S4100002
Year of Manufacture 2004. 1. 2
Conformance to EN 50081-1 : 1992

EMC-Directive 89/336 EEC and 92/31/EEC

EN 50130-4 : 1996

We, the undersigned, here by declare that the equipment specified above conforms
to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD
Signature Signature
Full Name YOUNG TAEK SON Full Name
Position QUALITY CONTROL MANAGER Position
Place CHANGWON, KOREA Place
Date 2004. 1. 2 Date

Legal Representative in Europe

MEMO

MEMO MEMO