SAMSUNG SVB10GVCIS Service Manual
VIDEO CASSETTE LINE RECORDER
SVR-18A
SVR-18B
SVR-18C
SERVICE
SVR-18B
SVR-18C
SVR-18A
ON STANDBY EJECT
REC SYSTEM
ON STANDBY STOP PLAY REC II P/S TRACKING
PLAY STOP
REW
F.F
ON STANDBY EJECT REC
ON STANDBY STOP PLAY REC II P/S
TRACKING
SYSTEM
REW PLAY STOP F.F
ON STANDBY EJECT
REC SYSTEM
ON STANDBY STOP PLAY REC II P/S TRACKING
PLAY STOP
REW
F.F
Manual
VIDEO CASSETTE LINE RECORDER CONTENTS
For mechanical disassembly and adjustment, refer to the “Mechanical Manual”
(DX7-A/AC, DX8-A/AC AC68-20392A).
1. Precautions
2. Reference Information
3. Product Specifications
4. Disassembly and Reassembly
5. Alignment and Adjustment
6. Exploded View and Parts List
7. Electrical Parts List
8. Block Diagrams
9. PCB Diagrams
10. Wiring Diagram
11. Schematic Diagrams
© Samsung Electronics Co., Ltd. APR. 1998 AC68-20404A
Samsung Electronics 1-1
1. Precautions
1. Be sure that all of the built-in protective devices are
replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be
sure to restore all pretective devices, including :
control knobs and compartment covers.
3. Make sure that there are no cabinet openings
through which people--particularly children
--might insert fingers and contact dangerous
voltages. Such openings include the spacing
between the picture tube and the cabinet mask,
excessively wide cabinet ventilation slots, and
improperly fitted back covers.
If the measured resistance is less than 1.0 megohm
or greater than 5.2 megohms, an abnormality exists
that must be corrected before the unit is returned
to the customer.
4. Leakage Current Hot Check (See Fig. 1) :
Warning : Do not use an isolation transformer
during this test. Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI C101.1,
Leakage Current for Appliances), and Underwriters
Laboratories (UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug the AC
line cord directly the power outlet. With the unitÕs
AC switch first in the ON position and then OFF,
measure the current between a known erath
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including : antennas, handle
brackets, metal cabinets, screwheads and control
shafts. The current measured should not exceed
0.5 milliamp. Reverse the power-plug prongs in the
AC outlet and repeat the test.
6. X-ray Limits :
The picture tube is designed to prohibit X-ray
emissions. To ensure continued X-ray protection,
replace the picture tube only with one that is the
same type as the original.
Fig. 1-1 AC Leakage Test
7. Antenna Cold Check :
With the unitÕs AC plug disconnected from the
AC source, connect an electrical jumper across the
two AC prongs. Connect one lead of the ohmmeter
to an AC prong.
Connect the other lead to the coaxial connector.
8. High Voltage Limit :
High voltage must be measured each time
servicing is done on the B+, horizontal deflection
or high voltage circuits.
Heed the high voltage limits. These include the
X-ray protection Specifications Label, and the
Product Safety and X-ray Warning Note on the
service data schematic.
9. Some semiconductor (Òsolid stateÓ) devices are
easily damaged by static electricity.
Such components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect transistors.
The following techniques will reduce the
occurrence of component damage caused by static
electricity.
10. Immediately before handling sny semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known
earth ground. Alternatively, wear a discharging
Wrist-strap device. (Be sure to remove it prior to
applying power--this is an electric shock
precaution.)
Device
Under
Test
(Reading should
not be above
0.5mA)
Leakage
Currant
Tester
Earth
Ground
Test all
exposed metal
surfaces
Also test with
plug reversed
(using AC adapter
plug as required)
2-Wire Cord
Precautions
1-2 Samsung Electronics
11. High voltage is maintained within specified limits
by close-tolerance, safety-related components and
adjustments. If the high voltage exceeds the
specified limits, check each of the special
components.
12. Design Alteration Warning :
Never alter or add to the mechanical or electrical
design of this unit. Example : Do not add
auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also, any
design changes or additions will void the
manufacturerÕs warranty.
13. Hot Chassis Warning :
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only if
the AC power plug is inserted so that the chassis
is connected to the ground side of the AC source.
To confirm that the AC power plug is inserted
correctly, do the following : Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the reading
is greater than 1.0V, remove the AC power plug,
reverse its polarity and reinsert. Re-measure the
voltage between the chassis and ground.
14. Some TV chassis are designed to operate with 85
volts AC between chassis and ground, regardless
of the AC plug polarity. These units can be safely
serviced only if an isolation transformer inserted
between the receiver and the power source.
15. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
16. Always connect a test instrumentÕs ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrumentÕs
ground lead last.
17. Observe the original lead dress, especially near
the following areas : Antenna wiring, sharp
edges, and especially the AC and high voltage
power supplies. Always inspect for pinched, outof-place, or frayed wiring. Do not change the
spacing between components and the printed
circuit board. Check the AC power cord for
damage. Make sure that leads and components
do not touch thermally hot parts.
18. Picture Tube Implosion Warning :
The picture tube in this receiver employs
Òintegral implosionÓ protection. To ensure
continued implosion protection, make sure that
the replacement picture tube is the same as the
original.
19. Do not remove, install or handle the picture tube
without first putting on shatterproof goggles
equipped with side shields. Never handle the
picture tube by its neck. Some Òin-lineÓ picture
tubes are equipped with a permanently attached
deflection yoke; do not try to remove such
Òpermanently attachedÓ yokes from the picture
tube.
20. Product Safety Notice :
Some electrical and mechanical parts have special
safety-related characteristics which might not be
obvious from visual inspection. These safety
features and the protection they give might be
lost if the replacement component differs from the
original--even if the replacement is rated for
higher voltage, wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
( or ).
Use replacement components that have the same
ratings, especially for flame resistance and
dielectric strength specifications. A replacement
part that does not have the same safety
characteristics as the original might create shock,
fire or other hazards.
Samsung Electronics 2-1
2. Reference Information
2-1 IC BLOCK
2-1-1 IC601 (HD6433977)
Reference Information
2-2 Samsung Electronics
2-1-2 IC301 (LA7411)
Reference Information
Samsung Electronics 2-3
2-1-3 IC302 (SS11501M/SS11511M)
Reference Information
2-4 Samsung Electronics
2-1-3 IC303 (SS23378M/SS23377M)
Samsung Electronics 3-1
3. Product Specifications
3-1 Product Specifications
Operation Description
Format VHS PAL standard
Video recording system Video : 2 rotary heads, helical scanning system
Luminance : FM azimuth recording
Color : Down converted subcarrier phase shifted direct recording
Television system CCIR Standard G/K
Color system PAL, MESECAM, NT 3.58, NT 4.43, NT PB
Tape width 12.65 mm (1/2 inch)
Tape speed PAL : 23.39 mm/sec, NTSC : 33.35 mm/sec
Recording/playback time 4 hours with E-240 Tape
F.F/REW time About 150 ~ 200 sec with E-180
Heads Video : 2 rotary heads
Audio/Control : 1 stationary head
Erase : 1 full track erase head
VIDEO
Input 0.5 to 2.0 Vp-p : 75 ohm unbalanced
Output 1.0 Vp-p : 75 ohm unbalanced
Signal-to-noise ratio Better than 43 dB
Horizontal resolution More than 240 lines
Audio
Input Line : -8 dBm, 47 Kohm unbalanced
Output Line : -8 dBm, 1 Kohm unbalanced
Signal-to-noise ratio More than 42 dB min (IHF A filter)
Frequency response 100Hz - 8KHz
Output channel Channel 22 - 69 (preset ch36)
Power requirement AC 230V 50/60 Hz, DC12V
Power consumption Approx. 13 watts
Operation temperature 41°F-104°F (5°C-40°C)
Operation humidity 10%-75%
Weight (net) 3.5 Kg
Dimensions (W x H x D) 360 x 90.5 x 290 mm
Design and specifications are subject to change without notice.
Product Specifications
3-2 Samsung Electronics
MEMO
Samsung Electronics 4-1
4. Disassembly and Reassembly
4-1 Cabinet Assembly
Note : Disassemble in the order shown.
Reassemble in reverse order.
4-1-1 Cabinet Top removal
ΠREMOVE 3 SCREWS
Fig. 4-1 Cabinet Top removal
4-1-2 Bottom cover removal
ΠREMOVE 2 SCREWS
Fig. 4-2 Bottom cover removal
Disassembly and Reassembly
4-2 Samsung Electronics
4-1-3 Ass’y Front Panel removal
(Bottom view)
´ RELEASE 4 HOOKS
ˇ RELEASE 3 HOOKS
(Top view)
Fig. 4-3 Ass’y Front Panel removal
Disassembly and Reassembly
Samsung Electronics 4-3
4-1-4 Ass’y Function-Timer removal
Note : Take extreme care not to damage the PCB when removing it.
ΠRELEASE 6 TABS
Fig. 4-4 Ass’y Function-Timer removal
Note : When removing chassis, take extreme care not to damage the main PCB front.
Disassembly and Reassembly
4-4 Samsung Electronics
4-1-5 Chassis removal
Fig. 4-5 Chassis removal
ΠREMOVE 2 SCREWS
´ REMOVE 2 SCREWS
Disassembly and Reassembly
Samsung Electronics 4-5
Note : When reinstalling the deck on the main PCB, take extreme care not to damage the sensor.
4-1-6 Main board removal
Fig. 4-6 Main board removal
ΠREMOVE 1 SCREW
Disassembly and Reassembly
4-6 Samsung Electronics
4-2 Circuit Board Locations
SHUTTLE BOARD
(OPTION)
MAIN BOARD
FUNCTION BOARD
Fig. 4-7 Circuit board locations
Samsung Electronics 5-1
5. Alignment and Adjustment
Note : After replacing the assÕy full deck, the assÕy main, the cylinder assÕy and the micom(IC601), the remote
control assÕy can be used to adjust the ÒX-point (tracking center) adjustmentÓ and ÒHead S/W pointÓ
adjustment.
5-1 Reference
5-1-1 The type of remote control ass’y
1. Remote control assÕy (AC93-10039Y/69099-633-252)
is specified as a service jig in the service manual of
X-5/X-6(DX5-R/DX5-RC/DX6-R/DX6-RC) chassis.
(See Fig. 5-1)
2. Normal remote control assÕy for X-7/X-8
(DX7-R/DX7-RC/DX8-R/DX8-RC) chassis.
(See Fig. 5-2)
5-1-2 How to identify between normal
remote control ass’y and multi
remote control ass’y for X-7/X-8
chassis (See Fig. 5-2)
1. The color of some buttons related to TV function are
gold.
2. Audio button is added instead of the test button
hidden behind of inlay.
3. The positions of some buttons are different.
EJECT
2
456
789
0
CLK/COUNT
REW
F.F
STOP
CLR/RST DISPLAY
Q-PRO
MENU
S
H
I
F
T
S
H
U
T
T
L
E
DAILY WEEKLY
REC
P/S
PRESET BAND
SEARCH MEMORY
OUTPUT
INDEX SLOW INPUT
INPUT BUTTON
SP/LP BUTTON
SP LP A.DUB VPS
FINE CH
TRK
(TRACKING, FINE)
BUTTON
POWER BUTTON
POWER
PLAY BUTTON
PLAY
TEST BUTTON IS
HIDDEN BEHIND
OF INLAY.
3
HEAD S/W ADJ.
("INPUT" OR "TEST"
AND "3" BUTTON)
1
TRACKING
CENTER ADJ.
("INPUT" OR "TEST"
AND "1" BUTTON)
633-252
REMOTE CONTROL
ASS'Y PART NO.
Fig. 5-1 Remote Control Ass’y Jig for X-5/X-6 Chassis
(AC93-10039Y/69099-633-252)
EJECT
2
456
789
0
CLK/COUNT
REW
F.F
STOP
AUDIO
DISPLAY
REC
P/S
INDEX A.TRK
INPUT BUTTON
FINE PROG
TRK
(TRACKING, FINE)
BUTTON
POWER BUTTON
POWER
PLAY BUTTON
PLAY
TEST BUTTON IS
HIDDEN BEHIND
OF INLAY.
3
HEAD S/W ADJ.
("INPUT" OR "TEST"
AND "3" BUTTON)
1
TRACKING
CENTER ADJ.
("INPUT" OR "TEST"
AND "1" BUTTON)
SYSTEM
CLR/RST
S
H
U
T
T
L
E
SPEED BUTTON
SPEED AFT
INPUT
TV/VCR
PICTURE
A.DUB
2
456
789
0
CLK/COUNT
REW
F.F
STOP
DISP./
REC
P/S
INDEX
VCR
POWER
PLAY
3
1
VCR
CLR/RST
S
H
U
T
T
L
E
SPEED
TV/VCR
PICTURE
A.DUB
NORMAL REMOTE CONTROL ASS'Y
(CAN ADJUST)
MULTI REMOTE CONTROL ASS'Y
(CAN NOT ADJUST)
-/--
FINE
AUDIO
ADD BUTTON(AUDIO)
GOLD COLOR
TV
GOLD COLOR
TV
POWER
INPUT
GOLD COLOR
VOLUME PROG
GOLD COLOR
MENU
Q-PRO
SLOW
SOFTEN OK SHARPEN
MENU
Q-PRO
SLOW
SOFTEN OK SHARPEN
Fig. 5-2 Remote Control Ass’y for X-7/X-8 Chassis
Alignment and Adjustment
5-2 Samsung Electronics
5-2 Mechanical Adjustment
Note : Refer to the Mechanical Manual ÒDX7-A/DX7-AC/DX8-A/DX8-AC (AC68-20392A)Ó for the adjustment
and confirmation of assÕy full deck.
5-2-1 The number and position of test point
GND
CTL
H'D SW
ENV.
A-OUT
V-OUT
W308
TP601
TP602
TP301
TP302
TP303
Fig. 5-3 The position of test point (Main PCB-Component side)
Test point : TP601 (CTL Pulse)
TP602 (H’D S/W -Trigger)
TP301 (Envelope)
TP302 (Audio out)
CTL PULSE
ENVELOPE
AUDIO OUT
H’D S/W -TRIGGER
Alignment and Adjustment
Samsung Electronics 5-3
5-2-2 X-Point(Tracking center) adjustment
(See the 2-2-1 (d) AC HEAD
POSITION(X-POINT) ADJUSTMENT
on page 2-3 of the mechanical
manual)
5-2-2 (a) IF THE REMOTE CONTROL ASS’Y IS
NOT AVAILABLE
1. Playback the colorbar alignment tape.
2. Connect CH-1 scope probe to ÒTP601Ó and CH-2
scope probe to ÒTP602Ó. And then, trigger head
switching pulse.
3. Set tracking preset to 2.7msec, using the ÒFINE
(Tracking)Ó button / of the other
remote control assÕy except the remote control
assÕy jig for X-5/X-6 chassis and the normal remote
control assÕy for X-7/X-8 chassis.
4. Insert the adjusting driver (+) into X-position
adjusting gear. Adjust the driver in either direction
for maximum envelope waveform.
Note :
Since the adjusting gear unit may be damaged, do
not adjust by force when adjusting the X-point using the
adjusting driver (+). After turn the X-point adjusting screw
(D) counterclockwise a little, perform the adjustment.
After adjustment is completed, tighten the screw.
5-2-2 (b) IF THE REMOTE CONTROL ASS’Y
(AC93-10039Y/69099-633-252) IS
AVAILABLE
Note : How to use the ÒTESTÓ button.
1. Disattach the inlay of remote control assÕy.
(See Fig. 5-1 and Fig. 5-2)
2. Press the ÒTESTÓ button with the pincers and the
precise driver as shown in Fig. 5-1 and 5-2)
1. When using the ÒINPUTÓ button of remote
control assÕy;
1) Simultaneously press the ÒINPUTÓ button and Ò1Ó
button in PB mode.
This will adjust the tracking center automatically.
2) Set the tracking preset using the ÒFINE (Tracking)
button of remote control.
3) After adjustment is completed, press the
ÒPOWERÓ button to release.
2. When using the ÒTESTÓ button of remote
control assÕy ;
1) Simultaneously press the ÒTESTÓ button and Ò5Ó
button in PB mode.
This will adjust the tracking center automatically.
2) Set the tracking preset using the ÒFINE (Tracking)
button of remote control.
3) After adjustment is completed, press the
ÒPOWERÓ button to release.
<Setting of scope>
- Volt/div. : CH-1 = 0.1V - Time/div. : 5msec
CH-2 = 0.2V
Fig. 5-4 Tracking preset adjustment
Fig. 5-5 Tracking preset adjustment
SCREW(C)
TILT ADJUST
X-POSITION
ADJUST GEAR
HOLE
SCREW(A)
HEIGHT ADJUST
SCREW(B)
AZIMUTH ADJUST
SCREW(D)
X-POINT LOCKING
Fig. 5-6 Location of A/C Head adjustment screw
2.7msec
CH-2 Probe
TP602
H'D S/W Pulse
CH-1 Probe
TP601
CTL Pulse
REMOTE
BUTTONS
CONTROL PULSE REMOVE
FINE
FINE
PUSH
PUSH
Alignment and Adjustment
5-4 Samsung Electronics
5-2-2 (b) IF THE NORMAL REMOTE CONTROL
ASS’Y OF X-7/X-8(DX7-R/DX7-RC/
DX8-R/DX8-RC) CHASSIS IS
AVAILABLE
Note 1 : Two kinds of remote control assÕy are used
for X-7/X-8(DX7-R/DX7-RC/DX8-R/
DX8-RC) chassis.
1. One is a normal remote control assÕy, the other is a
multi remote control assÕy
2. All adjustments are adjusted by normal remote
control assÕy only.
3. For the identification of normal remote control
assÕy and multi remote control assÕy, See page 5-1.
Note 2 : How to use the ÒTESTÓ button.
1. Disattach the inlay of remote control assÕy.
(See Fig. 5-1 and Fig. 5-2)
2. Press the ÒTESTÓ button with the pincers and the
precise driver as shown in Fig. 5-1 and 5-2)
1. When using the ÒINPUTÓ button of remote
control assÕy;
1) Simultaneously press the ÒINPUTÓ button and Ò1Ó
button in PB mode.
This will adjust the tracking center automatically.
2) Set the tracking preset using the ÒFINE (Tracking)
button of remote control.
3) After adjustment is completed, press the
ÒPOWERÓ button to release.
2. When using the ÒTESTÓ button of remote
control assÕy ;
1) Simultaneously press the ÒTESTÓ button and Ò5Ó
button in PB mode.
This will adjust the tracking center automatically.
2) Set the tracking preset using the ÒFINE (Tracking)
button of remote control.
3) After adjustment is completed, press the
ÒPOWERÓ button to release.
Alignment and Adjustment
Samsung Electronics 5-5
5-3 Electrical Adjustment
5-3-1 Head S/W Adjustment
Note : Only remote control assÕy can adjust.
5-3-1 (a) IF REMOTE CONTROL ASS’Y
(AC93-10039Y/69099-633-252) IS
AVAILABLE
1. When using the ÒINPUTÓ button of remote control
assÕy ;
1) Insert an SP tape into the housing assÕy.
2) Press the ÒPLAYÓ button.
3) Press the ÒINPUTÓ button and Ò3Ó button simultaneously.
4) This will adjust the head S/W point adjustment
automatically.
5) After the adjustment is completed, press
ÒPOWERÓ button to release.
2. When using the ÒTESTÓ button of remote control
assÕy ;
1) Insert an SP tape into the housing assÕy.
2) Press the ÒPLAYÓ button.
3) Press the ÒTESTÓ button and ÒSP/LPÓ button
simultaneously.
4) This will adjust the head S/W point adjustment
automatically.
5) After adjustment is completed, press the
ÒPOWERÓ button to release.
5-3-1 (b) IF NORMAL REMOTE CONTROL
ASS’Y FOR X-7/X-8(DX7-R/DX7-RC/
DX8-R/DX8-RC) CHASSIS IS
AVAILABLE
1. When using the ÒINPUTÓ button of remote control
assÕy ;
1) Insert an SP tape into the housing assÕy.
2) Press the ÒPLAYÓ button.
3) Press the ÒINPUTÓ button and Ò3Ó button
simultaneously.
4) This will adjust the head S/W point adjustment
automatically.
5) After the adjustment is completed, press
ÒPOWERÓ button to release.
2. When using the ÒTESTÓ button of remote control
assÕy ;
1) Insert an SP tape into the housing assÕy.
2) Press the ÒPLAYÓ button.
3) Press the ÒTESTÓ button and ÒSPEEDÓ button
simultaneously.
4) This will adjust the head S/W point adjustment
automatically.
5) After adjustment is completed, press the
ÒPOWERÓ button to release.
Alignment and Adjustment
5-6 Samsung Electronics
MEMO
Samsung Electronics 6-1
6. Exploded View and Parts List
6-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - -
6-2 Mechanical Parts (Top Side) - - - - - - - - - - - - - - - - - - - -
6-3 Mechanical Parts (Bottom Side) - - - - - - - - - - - - - - - - -
6-4 Housing Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - -
Page
6-2
6-4
6-6
6-8
Exploded View and Parts List
6-2 Samsung Electronics
6-1 Cabinet Assembly
S.N.A ; Service Not Available
157
157
CN77A
153
157
FULL DECK (S.N.A)
108
MAIN PCB (S.N.A)
S602A
S601A
SC301
661
LD601A
PT602A
PT601A
CN606A
CN601A
155
FUNCTION PCB
(S.N.A)
21
22
51
1
21
22
1
SVR-18A
SVR-18B SVR-18C
157
109
SHUTTLE PCB
(S.N.A)
21
22
1
TOP CABINET (S.N.A)
Exploded View and Parts List
Samsung Electronics 6-3
Loc. No Part No Description and Specification Remark
1
AC98-11240B
ASSY-PANEL FRONT SVR-18A
AC98-11249D ASSY-PANEL FRONT SVR-18B
AC98-11249F ASSY-PANEL FRONT SVR-18C
21
AC64-50928R
DOOR-CASSETTE SVR-18A
AC64-50928X DOOR-CASSETTE SVR-18B
AC64-50928Y DOOR-CASSETTE SVR-18C
22 AC61-62003A SPRING;-,SUS304,(GE/RCA),-,-,-,51
AC98-12073D
ASSY KNOB-SHUTTLE;SV-B10G,-
108
AC61-11004B
ASSY-CONNECTOR BOARD
109 AC63-30514A COVER-BOTTOM;SV-A120U,SECC,-,T0.5,-,153 AC60-12126A SCREW-BH;-,BH,-,4*12,FE,FZY,-,-,155 AC60-12134A SCREW-TAP BH;-,BH,-,2-4X16,-,FE
157 AC60-10063A SCREW-TAPTITE;BH,+,-,M3,L12,ZPC3,SWRCH18
661
AC39-10019A
POWER-CORD
CN601A 3809-001090 CABLE-FLAT;30V,80C,100mm,22P,1.0mm,UL289
CN606A 3809-001048 CABLE-FLAT;30V,80C,110mm,6P,1.25mm,UL289
CN77A 3809-001094 CABLE-FLAT;30V,80C,40mm,5P,1.25mm,UL2896
LD601A AC61-22345A HOLDER-LED;POM,-,-,-,-,PT601A AC61-22344A HOLDER-PHOTO;POM,-,-,-,-,PT602A AC61-22344A HOLDER-PHOTO;POM,-,-,-,-,S601A AC61-22321A HOLDER-TR;POM,-,-,-,-,S602A AC61-22321A HOLDER-TR;POM,-,-,-,-,SC301 AC98-12023J ASSY-S/C P/AMP TOP
Exploded View and Parts List
6-4 Samsung Electronics
6-2 Mechanical Parts (Top Side)
T216
T201
T207
T300
901
920
901
T203
T209
T240
900
T239
T210
956
956
956
T208
T227
T233
957
T234
T228
T230
T229
T231
901
T233
T204
T238
T232
T225
T226
952
G
T236
T211
T223
T217
T219
952
T218
T220 T221
T222
G
G
O
G
919
T224
T212
<DX7-AC/DX8-AC ONLY>
<DX7-AC/DX8-AC
ONLY>
T202
Exploded View and Parts List
Samsung Electronics 6-5
Loc. No Part No Description and Specification Remark
900 AC60-12091A SCREW-MACHINE;FP,BH,-,M3,L4,SWRCH10A,YEL ROB (OPTIONAL)
901 AC60-10012A SCREW-MACHINE;BH,+,M3,L8,-,FE,-,-,919 AC60-10004A SCREW-MACHINE;BH,+,M3,L8,ZPC,SWRCH18A,-,
920 AC60-10007A SCREW-TAPPING;BH,+,M2.6,L12,-,SWRCH18A,952 AC60-30018A WASHER-PLAIN;PLAIN,M3.2,D6,T0.5,POLYSLID
956 AC60-30007A WASHER-SLIT;PLAIN,ID2.5,OD7,T0.5,SPC1,-,
957 AC60-30008A WASHER-SLIT;-,ID3.5,OD9,T0.5,SPC1,-,T201 AC66-10023A REEL-DISK L ASSY;POM,-,PACKAGE,X-5,T202 AC66-10022A REEL-DISK R (ASSY);POM,-,PACKAGE,X-5,T203 AC66-30474A BRAKE-SUB L;-,PBT,-,-,-,X-5/IS
T204 AC66-30148A BRAKE SUB R;-,-,-,-,X5,T207 AC66-30475A BRAKE-MAIN L ASS’Y;-,POM+PELT,-,-,-,X-5/
T208 AC66-30476A BRAKE-MAIN R ASS’Y;-,POM+PELT,-,-,-,X-5/
T209 AC61-60112A SPRING- BRAKE MAIN;ES,SUS304WPB,PI0.35,I
T210 AC66-20073A GEAR RELAY S-ASSY;-,-,-,-,-,X5,T211 AC66-20037A GEAR- RELAY T;PEBAX7033,X-5,Z39,GEAR-SPU
T212 AC66-30073A ARM-TENSION ASSY;-,DX5-R,-,-,-,T216 AC61-60119A SPRING TENSION;ES,SWPB,PI0.4,D3,L33(OD3.
T217 AC66-30470A LEVER-REC S/W;-,PBT #3300,T4.0,L32,-,(XT218 AC61-62017A SPRING-SUB BRAKE L;ES,SUS304,PI0.23,D3.5
T219 AC33-10003P HEAD- MAGNET F/E;MH131S,-,-,-,L51.05XW7.
T220 AC66-82050A SLIDER-G/R ASSY(S);-,-,-,-,X-5
T221 AC66-82054A SLIDER-G/R ASSY(T);-,-,-,-,X-5
T222 AC33-10002E HEAD-CLEANER;-,-,-,X-5 (OPTIONAL)
T223 AC66-20065A RACK-HOUSING;L74.29,POM M90-44,BLK,M1,3.
T224 AC33-10216K HEAD-ACE ALL ASSY;-,-,-,-,X-7A
T225 AC66-80005A SLIDER-PINCH;POM(M90-44),T10.5,L54.35,NA
T226 AC66-30014A LEVER-REVIEW;ZYTEL(70G-43L),T5,-,PCD25.6
T227 AC66-30099A ARM-REVIEW ASSY;-,-,-,-,DX5-R,T228 AC66-30013A LEVER- CAM;PBT 6300T,-,L45,W9,X-5,T229 AC66-30003A LEVER-PINCH COMP;PBT 3300,T7.5,L45.25,-,
T230 AC61-60116A SPRING- PINCH COMP;TS,SWPB,PI1.0,D6,L38(
T231 AC67-32001A PRISM-LED;PMMA,D5,IF-850,-,-,T232 AC66-82049A SLIDER-PUSH;LUPOX 2150,T2,-,NTR,T233 AC61-62016A SPRING-SLIDE PUSH;ES,SUS304WPB,PI0.55,D3
T234 AC59-90402A UNIT-PINCH ROLLER;X-7A,RESIN BEARING
T236 AC66-10010A IDLER-ASSY;PACKAGE,-,X-5,T238 AC61-60132A SPRING ARM PINCH;CS,SUS304WPB,PI0.4,D7.1
T239 AC66-30132A LEVER JOG-ASS’Y;-,-,-,X-5 (OPTIONAL)
T240 AC61-60505A SPRING-REC S/W;-,ES,SUS304 WPB,PI0.29,PI
T300 AC96-10475D ASSY-CYLINDER;CX8A-S2P
Exploded View and Parts List
6-6 Samsung Electronics
6-3 Mechanical Parts (Bottom Side)
B257
G
G
O
B256
B254
951
951
952
918
B258
B261
B255
B260
B267
B266
B265
956
902
922
B259
B262
B253
B263
B268
B251
958
B252
G
B264
Exploded View and Parts List
Samsung Electronics 6-7
Loc. No Part No Description and Specification Remark
902 AC60-10051A SCREW-TAPPING;BH,-,-,M3,L8,FZY
918 AC60-10041A SCREW-TAPPING;BH,+,-,M2.6XL7.5,ZPC3
922 AC60-10504A SCREW-MACHINE;-,PH,+,-,M3,L3,FE,FZY,YEL
951 AC60-30025A WASHER-SLIT;-,ID2.5,OD5.0,T0.5,POLY SLID
952 AC60-30018A WASHER-PLAIN;PLAIN,M3.2,D6,T0.5,POLYSLID
956 AC60-30007A WASHER-SLIT;PLAIN,ID2.5,OD7,T0.5,SPC1,-,
958 AC60-30028A WASHER-SLIT;-,D2.5,D9.0,T0.5,NUMIRROR,-,
B251 AC66-82043A SLIDER-MAIN;TOPEX 4010S,-,-,-,B252 AC66-20019A GEAR-LOADING L ASSY;-,-,-,PACKAGE,-,X-5,
B253 AC66-20069A GEAR-LOADING R ASSY;-,-,-,-,-,X5,B254 AC61-60115A SPRING-BRAKE CAPSTAN;ES,SUS304WPB,PI0.4,
B255 AC66-20004A GEAR-MASTER;POM (M90-44),M 1,Z 60,SP,-,X
B256 AC31-12006A MOTOR-D/D CAPSTAN;DMVCMC07A,-,B257 AC66-62008A BELT-CAPSTAN;-,DLB-601,T2,8,L134.9,BLK,X
B258 AC66-20066A GEAR-CLUTCH ASSY;X-5,-,-,-,-,-,B259 AC66-32185A LEVER-SLIDER PINCH;PBT,T4,NAT,-,-,B260 AC66-20016A GEAR- WORM WHEEL;POM SW-01,M0.55/M1,Z57/
B261 AC66-30011A LEVER- SHIFT;PBT2002K,T10.9,L35,-,-,B262 AC66-30012A LEVER- IDELR CHANGE;PBT330,T33,L50,-,W6.
B263 AC61-60111A SPRING-LEVER SHIFT;TS,SWPB,PI0.7,D5.5,L1
B264 AC59-90001A UNIT-LOADING ASSY;X-5,-,B265 AC31-12015A MOTOR-LOADING ASSY;POM+RF370C X-5
B266 AC66-20039A GEAR- WORM LO;PBT 2002K,-,-,-,D4.5,3,B267 AC61-20224A HOLDER SHAFT;POM M90-44,T1.25,NTR,PI5XH5
B268 AC66-30149A BRAKE CAPSTAN;-,-,-,-,X5,-
Exploded View and Parts List
6-8 Samsung Electronics
6-4 Housing Assembly
Loc. No Part No Description and Specification Remark
914
902
H510
H550
H500
H520
H522
H524
H526
902
H521
H533
H532
H531
H535
H530
H540
H545
H544
H541
H543
H542
914
914
902 AC60-10051A SCREW-TAPPING;BH,-,-,M3,L8,FZY
914 AC60-10067A SCREW-TAPTITE;PWH,+,-,M3,L8,MFZN2-C,SWCH
H500 AC61-82014D HOUSING-ASSY;-,X7FL26280B,230X130X60,-,X
H510 AC61-10006A CHASSIS- UPPER;SECC 20/20,-,T1.0,BLK,-,X
H520 AC61-20932B HOLDER-CASSETTE ASSY;-,X5FL06080A,-,-,-,
H521 AC61-20922B HOLDER-CASSETTE;-,SECC T1.2,-,NAT,-,X-7(
H522 AC66-30018A LEVER-LOCK R;SECC 20/20,T1.2,L44,W32,-,H524 AC61-60121A SPRING-LEVER LOCK;ES,SUS304 WPB,PI0.2,D2
H526 AC66-30019A LEVER-KEY CASSETTE;LUCEL N109-LD,T2.5,L2
H530 AC61-11033A CHASSIS-SIDE L ASSY;-,-,-,-,-,X5FL0505A,
H531 AC61-10004A CHASSIS- SIDE L;ABS HF-380,-,T10,BLK,-,X
H532 AC66-30004A LEVER- LIGHT SHUTTER;LUCEL N109-LD,T2.5,
H533 AC61-60142A SPRING- LIGHT;ES,SUS304WPB,PI0.2,L11.4(O
H535 AC66-30017A LEVER- DOOR;LUCELN109-LD,T3.5,L74.3,W21.
H540 AC61-11032A CHASSIS-SIDE R ASSY;-,-,-,-,-,X5FL0505A,
H541 AC61-10003A CHASSIS- SIDE R;ABS HF-380,-,T10,BLK,-,X
H542 AC66-80008A SLIDER DAMPER;LUCEL N109-LD,T4,L87,-,-,H543 AC61-60120A SPRING-SLIDER;ES,SUS 304WPB,PI0.4,D3.8,L
H544 AC66-30016A LEVER- LID OPENER;LUCEL N109-LD,T4.0,L34
H545 AC61-60123A SPRING-LID OPENER;TS,SWPB,PI0.55,D8.9,L1
H550 AC61-50654A SHAFT-ARM ASSY;-,SUM24L,-,-,-,-,X-5
SMPS/POWER PARTS (230 VOLTAGE)
C1D41 2401-000306 C-AL;100uF,20%,25V,GP,6.3x11mm,2.5m
C1D42 2202-000780 C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5
C1P04 2401-001912 C-AL;1uF,20%,50V,GP,5x11mm,2mm,BK
C1S01 2305-001021 C-FILM,MPEF;100nF,20%,275V,TP,17.5x7x13.
C1S02 2201-000808 C-CERAMIC,DISC;2.2nF,10%,400V,Y5P,12x7.5
C1S03 2201-000934 C-CERAMIC,DISC;3.3nF,20%,400V,Y5P,18x8,1
C1S05 2305-001021 C-FILM,MPEF;100nF,20%,275V,TP,17.5x7x13.
C1S11 2401-003302 C-AL;47uF,20%,400V,GP,TP,18X31.5,7.
C1S12 2201-000934 C-CERAMIC,DISC;3.3nF,20%,400V,Y5P,18x8,1
C1S13 2201-000915 C-CERAMIC,DISC;100pF,10%,1KV,Y5P,TP,6x5,
C1S15 2401-000905 C-AL;22UF,20%,16V,BP,-,6X11,2.5MM
C1S16 2301-000361 C-FILM,PEF;1.2NF,10%,50V,TP,-,5MM
C1S17 2301-000445 C-FILM,PEF;4.7nF,5%,50V,5.5x7x3mm,5mm,TP
C1S18 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm
C1S19 2401-001912 C-AL;1uF,20%,50V,GP,5x11mm,2mm,BK
C1S20 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm
C1S21 2401-000970 C-AL;22uF,20%,50V,WT,TP,5x11,2mm
C1S30 2401-000385 C-AL;10UF,20%,100V,GP,-,6.3X11,2.5M
C1S32 2401-001998 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C1S33 2401-000306 C-AL;100uF,20%,25V,GP,6.3x11mm,2.5m
C1S34 2401-000118 C-AL;1000uF,20%,10V,GP,TP,10x12.5,5
C1S35 2401-000306 C-AL;100uF,20%,25V,GP,6.3x11mm,2.5m
C1S38 2301-000129 C-FILM,PEF;100nF,5%,50V,10X9X4.3X5,5mm,T
CN1S01 3711-000178 CONNECTOR-HEADER;1WALL,2P,1R,3.96mm,STRA
D1D41 0402-000132 DIODE-RECTIFIER ;1N4004,400V,1A,DO-41
D1D42 0402-000132 DIODE-RECTIFIER ;1N4004,400V,1A,DO-41
D1D43 0402-000132 DIODE-RECTIFIER ;1N4004,400V,1A,DO-41
D1D44 0402-000132 DIODE-RECTIFIER ;1N4004,400V,1A,DO-41
D1P05 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,500mW,
D1P06 0402-000132 DIODE-RECTIFIER ;1N4004,400V,1A,DO-41
D1S01 0402-001009 DIODE-RECTIFIER;1SR139,600V,1A,MSR
D1S02 0402-001009 DIODE-RECTIFIER;1SR139,600V,1A,MSR
D1S03 0402-001009 DIODE-RECTIFIER;1SR139,600V,1A,MSR
D1S04 0402-001009 DIODE-RECTIFIER;1SR139,600V,1A,MSR
D1S11 0402-000378 DIODE-RECTIFIER;EG01C,1000V,500mA,DO-41
D1S12 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,500mW,
D1S13 0402-001013 DIODE-RECTIFIER;1SR153-400,400V,800mA,DO
D1S30 0402-001013 DIODE-RECTIFIER;1SR153-400,400V,800mA,DO
D1S32 0402-001069 DIODE-RECTIFIER;RL10Z,200V,2A,DO,TP
D1S33 0402-001069 DIODE-RECTIFIER;RL10Z,200V,2A,DO,TP
F1S01 A3065-0157 FUSE;FST 250V 1.6A 20MM SEMKO S505 C
IC1P02 AC14-12001E IC;KA7809,-,IC1S13 0604-011028 PHOTO-COUPLER;PS2561-1 ST DIP
IC1S31 AC14-12006D IC;KA431Z,TO-92,TAPING
L1S02 A1151-0042 COIL-LINE FILTER;BSF-2120Z 25MH 3.2OHM
L1S03 AC27-92001M INDUCTOR;70UH-M RT BFS3565R2F,-,-,-,L1S12 AC27-92001M INDUCTOR;70UH-M RT BFS3565R2F,-,-,-,L1S30 AC27-12001N COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,L1S31 AC27-12001N COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,-
PT1S11 AC26-20120C TRANS-SWITCHING;-,100/230V,UL/CSA,EE28*2
Q1P02 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
Q1P04 0504-000118 TR-DIGITAL;KSR1003,NPN,300mW,22K-22K,TOQ1P05 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
Q1P06 0501-000610 TR-SMALL SIGNAL;KSA928A-Y,PNP,1W,TO-92L,
Q1S11 0502-001050 TR-POWER;2SC4517A,NPN,30W,TO-220,ST,10Q1S12 0501-000442 TR-SMALL SIGNAL;KTC3203-Y,NPN,400MW
R1P01 2004-001096 R-METAL;560ohm,5%,1/4W,AA,TP,2.4X6.4mm
R1P05 2004-000571 R-METAL;220ohm,5%,1/4W,AA,TP,2.4x6.4mm
R1P08 2001-000449 R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1P09 2001-000221 R-CARBON;1.2Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1P10 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R1P11 2004-001096 R-METAL;560ohm,5%,1/4W,AA,TP,2.4X6.4mm
R1S11 2006-000262 R-CEMENT;2.7ohm,10%,2W,CB,ST,7.5x11x20.
R1S12 2001-000305 R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1S13 2001-000305 R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1S14 2001-000305 R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1S15 2001-000305 R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1S17 2006-000273 R-CEMENT;27Kohm,5%,2W,CA,BK,6.4x27x6.4m
R1S18 2003-000264 R-METAL OXIDE;300ohm,5%,1W,AD,TP,4.3x12m
R1S19 2001-000003 R-CARBON ;330 OHM,5%,1/8W,AA,T
R1S20 2001-000003 R-CARBON ;330 OHM,5%,1/8W,AA,T
R1S21 2003-000273 R-METAL OXIDE;33Kohm,5%,2W,AA,TP,6x16mm
R1S30 2001-000515 R-CARBON;220ohm,5%,1/8W,AA,TP,1.8x3.2mm
R1S31 2001-000221 R-CARBON;1.2Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1S32 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R1S33 2004-000869 R-METAL;3Kohm,1%,1/8W,AA,TP,1.8x3.2mm
R1S34 2004-000459 R-METAL;2.2Kohm,1%,1/8W,AA,TP,1.
R1S40 2003-000119 R-METAL OXIDE;0.68ohm,5%,2W,AE,TP,6x16mm
VA1S01 1405-001026 VARISTOR;470V,600A,9x7mm,TP
ZD1P05 0403-000557 DIODE-ZENER;MTZ5.1C,5.1V,5.09-5.37V,500m
ZD1S11 0403-000539 DIODE-ZENER;MTZ18C,18V,17.42-18.33V,500m
ZD1S12 0403-000294 DIODE-ZENER;MTZ4.7B,4.55-4.80V,500mW,DOZD1S30 0403-000571 DIODE-ZENER;UZP43B,43V,40-46V,1W,DO-41,T
SYSTEM CONTROL/SERVO PARTS
C601 2202-000807 C-CERAMIC,MLC-AXIAL;22NF,+80-20%,25V,Y5V
C602 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C603 2202-000850 C-CERAMIC,MLC-AXIAL;2.2NF,30%,16V,Y5R,TP
C604 2202-000781 C-CERAMIC,MLC-AXIAL:100pF,10%,50V,Y5P,TP
C605 2401-000918 C-AL;22uF,20%,16V,GP,-,6.3x7,5
C606 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C607 2202-000781 C-CERAMIC,MLC-AXIAL:100pF,10%,50V,Y5P,TP
C608 2202-000807 C-CERAMIC,MLC-AXIAL;22NF,+80-20%,25V,Y5V
C609 2202-000781 C-CERAMIC,MLC-AXIAL:100pF,10%,50V,Y5P,TP
C610 2202-000791 C-CERAMIC,MLC-AXIAL;150PF,10%,50V,Y5P,TP
C6107 2202-000162 C-CERAMIC,MLC-AXIAL;15pF,5%,50V,SL,TP,3.
C611 2401-001952 C-AL;4.7UF,20%,50V,-,TP,6.3X7,5
C6114 2202-000145 C-CERAMIC,MLC-AXIAL;120PF,10%,50V,Y5P,3.
C6119 2401-001572 C-AL;47UF,20%,50V,GP,-,6.3X11,2.5MM
C612 2401-001511 C-AL;47UF,20%,16V,GP,-,6X7,5
C6120 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C6126 2401-000419 C-AL;10UF,20%,16V,GP,-,4X7,5
C613 2202-000780 C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5
C614 2401-001325 C-AL;470nF,20%,50V,GP,TP,3x5,5
C615 2202-000781 C-CERAMIC,MLC-AXIAL:100pF,10%,50V,Y5P,TP
C616 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C617 2202-000216 C-CERAMIC,MLC-AXIAL;27pF,5%,50V,SL,TP,3.
C6170 2202-000780 C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5
C618 2202-000216 C-CERAMIC,MLC-AXIAL;27pF,5%,50V,SL,TP,3.
Loc.No
Part No Desc & Spec Remark
Loc.No
Part No Desc & Spec Remark
Samsung Electronics
7-1
7. Electrical Parts List
Loading...