Samsung SU-2900 User Manual

Vacuum

Cleaner

SU-2900 Series

FOR HOUSEHOLD USE ONLY

Operating

Instructions

IMPORTANT SAFETY INSTRUCTIONS................................1

ASSEMBLING PARTS.............................................................2

OPERATION ........................................................................3

MAINTENANCE..................................................................4

TROUBLESHOOTING .....................................................6

ASSEMBLED VACUUM CLEANER PARTS ........

ATTACHING THE HANDLE..........................2

ATTACHING THE HOSE AND TOOLS.......2

Read these instructions before operating the vacuum cleaner

※The design and specification may be different depending on the models.

IMPORTANT

Thank you for purchasing a Samsung vacuum cleaner. When using an electrical appliance, basic precautions should alwa ys be f ollo wed, including the following:

SAFETY INSTRUCTIONS

PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.

WARNING:

• Do not leave v acuum cleaner unattended when it is plugged in.

• Unplug from outlet when not in use and before servicing.

• Do not use outdoors or on wet surfaces.

• Do not allow children to operate vacuum cleaner or use as a to y.

• Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only manufacturer’ s recommended attachments .

• Do not use with damaged cord or plug.

• If vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors or dropped in water , take it to a service center .

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull the cord around sharp edges or corners. Keep cord awa y from heated surf ace.

• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

• Do not handle vacuum cleaner or plug with wet hands.

• Do not put any object into openings. Do not use with any opening b loc ked; k eep openings free of dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

• Do not use without dirt cup or filters in place. Empty cup and clean filter frequently when picking up very fine materials such as powder .

• Turn off all controls before unplugging vacuum cleaner.

• Use extra care when cleaning on stairs .

• Do not use to pick up flammable or comb ustib le materials such as gasoline or fine wood standings or use in areas where they may be present.

• Store your vacuum cleaner indoors in a cool, dry area.

• Av oid picking up hard, sharp objects with the cleaner, they may damage the cleaner.

• Always turn off this appliance bef ore connecting or disconnecting the hose, remo ving the bottom plate for maintenance.

• Use only on dry , indoor surf aces , ne v er change the plug in any w a y.

• Do not modify the polarized plug to fit a non-polarized outlet or extension cord.

• Do not touch the brush roller when it is rotating.

• Keep suction a wa y from y our f ace when using nozzles and pipe .

• Do not pull the power cord around sharp corners and do not allow it to become trapped.

• Unplug before connecting turbine nozzle.(only using turbine-brush model)

To reduce the risk of fire, electric shock, or injury:

SAVE THESE INSTRUCTIONS FOR FUTURE USE. THIS VACUUM CLEANER HAS A POLARIZED PLUG.

To reduce the risk of electrical shock, this appliance has a polarized plug (one blade wider than the other.) This plug will fit in a polarized outlet only one w a y. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet.

Assembling Parts

Assembled Vacuum Cleaner Parts

1-1

Front Back

The assembled cleaner will look like the illustration to the left.

1.Handle

2.Power switch

3.Quick release cord hook

4.Post-Motor Filter

5.Crevice tool

6.Handle release

7.Carrying handle

8.Hose

9.Extension wand

10.Combination tool

11.Cyclone-Lever

12.Dirt Cup

13.Filter Cup

14.Upper Tank

15.Louvers

16.Hose Wand Base

17.Height Adjustment Dial

18.Hose Clip

WARNING!

OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

Step 1. Attaching the Handle

1-2 1-3

Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body.

Insert the screw provided into the existing hole. Tighten the screw securely with a screwdriver. Before securing the handle, please check that the handle is fitted to the vacuum body and make sure there’s no gap.

Step 2. Attaching the Hose and Tools

1-4 1-5

Slide the end of the hose wand with tabs into the Hose Wand Base.

Slide the extension wand and the crevice tool together into the storage clip.

Operation

2-1 2-2 2-3

ON-OFF Switch

1.To turn cleaner on, press the Power switch.

2.To the cleaner off, press the Power switch again .

Handle positions

The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating for general operation on carpet and floors; low for reaching under low furniture. Step on handle release pedal to lower handle.

2-4 2-5

Carrying handle

The cleaner can also be moved by using the carrying handle.

2-6

Cleaning Tool attachments

Attachment tools can be used to clean furniture or drapes, on stairs or in corners.

��

option

Transporting cleaner

To move your cleaner from room to room, put the handle in upright position, tilt the cleaner back on its rear wheels and push forward.

When using the attachments, ensure the vacuum cleaner is placed firmly on the floor with the handle in the upright position. Do n o t p l ace the vacuum on top of furniture or steps as the brushroller may cause damage.

A. Combination tool:

Two types of cleaning tools are included in one attachment: rotate for desired tool. ∙Use brush side to dust furniture,

blinds, books, lamps, shelves.

∙Use upholstery side for curtains,

draperies, cushions, fabrics.

B. Crevice tool:

Use in corners, on stairs, baseboards, and behind furniture.

C. Extension Wand:

Use with desired attachments and narrow wand for a longer reach.

��

option : Mini Turbo Brush

Refer to the separated instruction.

Cleaning lightweight flexible rugs

Stand on one end of rug and move cleaner toward other end or edge. Before reaching edge, push down on handle. This will lift up the nozzle(front of cleaner)and will prevent rug from clinging to cleaner. Continue to lift front of cleaner so that when you have reached the edge, it is completely off the rug. Move cleaner back to start again, lower front of cleaner, and use only forward strokes.

2-7

2-8

Carpet height adjustment

Carpet and rug cleaning takes place at the nozzle (A).

When it is necessary to raise and lower the nozzle for various carpet pile heights, rotate the nozzle control dial (B) to the desired setting.

For maximum cleaning performance, The following carpet height settings are recommended:

∙Lowest setting: for all types of carpet ∙Higher settings: for very deep pile carpet where

easier pushing effort is desired, while maintaining good cleaning performance.

Note: If the cleaner is difficult to push, rotate knob to the next higher setting.

Maintenance

Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness.

When to empty the Dirt Cup

The dirt cup needs to be emptied when the dirt reaches the "Full" line on the side of the Cup. If more dirt than this accumulates, your cleaner will not operate effectively.

Note: All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming.

Emptying the Dirt Cup

Disconnect cleaner from electrical outlet.

3-1 3-2 3-3

Full Line

Unlock

Position

Slide the Cyclone-Lever to the "Unlock" position. Grasp handle and pull the Dirt Cup straight out to remove from Vacuum.

Lock Position

Empty dirt into garbage container. Put the Dirt Cup back in the vacuum and slide the lever to the "Lock" position.

Cleaning the Pre/Post-motor Filter

3-4

Pre-Motor Filter

How to clean

Disconnect cleaner from electrical outlet.

The Pre-Motor Filter protects the Motor from debris. It is located underneath the Dirt Cup and Filter Cup in the Center of the round part of the Cyclone-Lever. Remove the small round Filter and any debris on top of it. Rinse well under warm water, then air dry thoroughly before replacing.

3-5

Post-Motor

Filter

The Post-Motor Filter assists in the filtation process to return clean air to the room. It is located behind the door on the front of the Cleaner. When the filter becomes dirty, open the door, remove the filter and shake the dust off the filter.The PostMotor Filter is non-washable therefore do not wash it in water. Replace the door by inserting the tabs on the left side and snapping the right side into place.

Do not operate cleaner without Either the Pre-Motor Filter or Post-Motor Filter in place.

Cleaning The Circular Filters.

Grasp the Filter Cup located at the bottom of the Dirt Cup and twist counterclockwise to unlock and remove.

3-6

Grasp the Circular Filters and twist to unlock Pull straight up to remove. Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water. Mild detergent may be used if desired. Rinse well, then air dry Thoroughly dry before putting them back together and replacing in the Filter Cup The Filter Cup may be washed In warm water with a mild detergent. Make sure it is completely dry before reassembling with fliters.

+ 11 hidden pages