Samsung SSC-12P User Manual

GVI dba Samsung CCTV 1621 West Crosby, Suite 104 Carrollton, TX 75006 PHONE : 866-492-8246

Printed in Korea Part No. :14021-1282

B/W OBSERVATION SYSTEM

Installation Manual

SSC-12P

Graphic Symbol Explanation

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated ‘dangerous voltage’ within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

Warning - To Prevent Fire or Shock Hazard, Do Not

Expose This Monitor To Rain or Moisture.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

IMPORTANT SAFEGUARDS

Caution

Power source is indicated on the rear of the set. It contains high-voltage parts. If you

remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself.

(Control switches are at the front of the monitor).

1. Read Instructions : All the safety and operating instructions should be read before

the appliance is operated.

2. Retain Instructions : The safety and operating instructions should be retained for

future reference.

3. Heed Warnings : All warnings on the monitor and in the operating instructions

should be adhered to.

4. Follow Instructions : All operating and use instructions should be followed.

5. Cleaning : Unplug this monitor from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Exception. A monitor that is meant for uninterrupted service and that for some

specific reason, such as the possibility of the loss of an authorization code for a

CATV converter, is not intended to be unplugged by the user for cleaning or any

other purpose, may exclude the reference to unplugging the monitor in the cleaning

description otherwise required in Item 5.

6. Attachments : Do not use attachments not recommended by SAMSUNG as they

may cause hazards.

7. Water and Moisture : Do not use this monitor near water for example, near a

bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a

swimming pool and the like.

8. Accessories : Do not place this monitor on an unstable cart, stand, tripod, bracket,

or table. The monitor may fall, causing serious injury to a child or adult, and

serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or

table recommended by SAMSUNG, or sold with the monitor. Any mounting of the

monitor should follow SAMSUNG’s instructions, and should use a mounting

accessory recommended by SAMSUNG.

9. Ventilation : Slots and openings in the cabinet are provided for ventilation and to

ensure reliable operation of the monitor and to protect it from overheating, and

these openings should never be blocked by placing the monitor on a bed, sofa, rug,

or other similar surface. This monitor should never be placed near or over a

radiator or heat register.

This monitor should not be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or SAMSUNG’s instructions have been

adhered to.

10. Power Sources : This monitor should be operated only from the type of power

source indicated on the making label. If you are not sure of the type of power

supply to your installation site, consult your SAMSUNG dealer or local power

company.

11. Grounding or Polarization : For monitors equipped with a 3-wire grounding-type

plug having a third(grounding)pin. This plug will only fit into a grounding type

power outlet. This is a safety feature. If you are unable to insert the plug into the

outlet, contact your electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the grounding-type plug.

12. Power : Cord Protection-Power supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience receptacles, and the point where

they exit from the monitor.

13. Lightning : For added protection for this monitor during a lightning storm, or

when it is left unattened and unused for long periods of time, unplug it from the

wall outlet and disconnect the cable system. This will prevent damage to the

monitor due to lightning and power-line surges.

14. Overloading : Do not overload wall outlets and extension cords as this can result

in a risk of fire of electric shock.

15. Object and Liquid Entry : Never push objects of any kind into this monitor

through openings as they may touch dangerous voltage points or short-out parts

that could result in a fire or electric shock.

Never spill liquid of any kind on the monitor.

16. Servicing : Do not attempt to service this monitor yourself as opening or removing

covers may expose you to dangerous voltage or other hazards. Refer all servicing

to qualified service personnel.

17. Damage Requiring Service : Unplug this monitor from the wall outlet and refer

servicing to qualified service personnel under the following conditions.

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the monitor.

c. If the monitor has been exposed to rain or water.

d. If the monitor does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions as an improper adjustment of other controls may result in damage

and will often require extensive work by a qualified technician to restore the

monitor to its normal operation.

e. If the monitor has been dropped or the cabinet has been damaged.

f. When the monitor exhibits a distinct change in performance-this indicates a

need for service.

18. Replacement Parts : When replacement parts are required, be sure the service

technician has used replacement parts specified by SAMSUNG or have the same

characteristics as the original parts.

Unauthorized substitutions may result in fire, electric shock or other hazards.

19. Safety Check : Upon completion of any service or repairs to this monitor, ask the

service technician to perform safety checks to determine that the monitor is in

proper operating condition.

FCC & ICES Information

Warning

This equipment has been tested and found to comply with the limits for a class A

digital device, pursuant to part 15 of the FCC Rules and ICES-003 of Industry

Canada. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the

interference at his own expense.

User-Installer Caution

Your authority to operate this FCC verified equipment could be voided if you make

changes or modifications not expressly approved by the party responsible for

compliance to part 15 of the FCC Rules.

6E7

Contents

IMPORTANT SAFEGUARDS ..................................................... 3

1. System Components and Installation ........................................ 8

1-1. System Components........................................................... 8

1-2. System Configuration ........................................................ 9

1-3. Individual Component Installation................................... 10

1-4. Basic System Installation ................................................. 21

2. Connecting Peripheral Devices ............................................... 22

2-1. Connecting a PIR Sensor ................................................. 22

2-2. Connecting a VCR ........................................................... 22

3. Part Names and Functions....................................................... 23

3-1. Camera ..............................................................................23

3-2. PIR Camera ...................................................................... 25

3-3. Monitor Front................................................................... 27

3-4. Monitor Rear.....................................................................29

4. Operation Function Instruction ............................................... 30

5. Technical Specifications.......................................................... 31

1. System Components and Installation

1-1. System Components

STANDARD CAMERA

PIR CAMERA

Mount-Corner

CAMERA CABLE

MONITOR

CAMERA MOUNT BRACKET

INSTALLATION MANUAL

Alarm Terminal-BLOCK

1-2. System Configuration

Model Name Quantity Note

Monitor SSC-12PM 1

Standard Camera SSC-12C 1

PIR Camera SMM-PIRCAM BW 1

SCREWS (BH M3✕30,BH M3✕16)

Anchor (HUD5), Mount-Corner

Camera Mount Bracket SBR-110 1

SCREW 3EA(M4✕L15)

Camera Cable

MCB-60 1

MCB-100 1

Installation Manual 1

Alarm Terminal Block 1

1-3. Individual Component Installation

1) INSTALLING STANDARD CAMERA (SSC-12C)

Caution to install SSC-12C outdoors

1. SSC-12C is designed to be protected from the water drops which are falling on the upper side of camera in a range of 15°. (Dust-water protection level : IP42) Therefore, be sure to install it in a location which is fit in above condition when you install it outdoor.

SSC-12C camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110).

●

Choose an installation site that can sufficiently support the weight of the equipments to be installed.

●

Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15).

●

Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket.

4 ✕ 15 sized

screws

wall or ceiling

2) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA (SSC-12C)

! Overview

CAMERA MOUNT BRACKET (SBR-110) is used to attach the camera to a wall, ceiling or shelf.

@ Installation

Explains the installation of CAMERA MOUNT BRACKET as well as the installation of the camera onto the CAMERA MOUNT BRACKET.

●

Choose an installation site that can sufficiently support the weight of the equipment to be installed.

●

Attach the camera mount bracket to the wall using the supplied screws (M4 X L15).

●

Adjust the camera to target the video location and tighten the bracket handle on the camera mount bracket. Install the camera onto the male screw of the Camera Mount Bracket by rotating the camera in clockwise.

●

Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position. Tighten the handle, turning it clockwise, and lock the camera in position.

●

Connect the camera cable to the camera.

# Specifications

Use : Indoor

Installation : Wall or Ceiling

Dimensions : 57(W) ✕ 47.2(H) ✕ 100.5(L)

Weight : 150g

Operating Temperature : -10 °C ~ 50 °C

$ Accessories

SCREW (M4 ✕ L15) ............ 3 pcs

Handle

3) INSTALLING PIR CAMERA(SMM-PIRCAMBW)

! Camera installation Hints

●

Do not install directly towards rising or setting sun. Can cause burn or damage to internal options.

●

Do not limit desired detection zone by interference of curtains, screens, potted plants, etc.

●

Also, do not locate it in front of source of water/oilvapors. Avoid placement of heat source inside detection zone.

●

Do not install outdoors.

@ Installing the PIR Camera

●

Choose an installation site that can sufficiently support 5 times the weight of the equipments to be installed.

●

Remove the screw (BH M2. 6) at the bottom of the main unit by turning it counterclockwise, and then lift the assy-case front as you push it upward to detach it from the case-rear. (✳ Do not apply excessive force, as doing so may damage the inside assembly.)

●

Place the case-rear over the installation site and mark screw holes with a pencil (indicated by the red circles in the illustration). Drill a pilot hole for each pencil mark (5mm in diameter and at least 35mm in depth), and then fully insert the supplied plastic anchors (HUD 5) into them.

Assy-case front

BH M2. 6

CASE-REAR

●

Connect the RJ-11 connector cable to the case-rear as well as the cable to be connected to the terminal.

●

Align the two holes of the case-rear to the holes of the plastic anchors, and then fasten the screw-tappings (BH M3 ✕ 30)

SCREW-TAPPIN

(BH M3 ✕ 30)

SCREW-TAPPIN

(BH M3 ✕ 30)

●

Adjust the direction of the lens.

1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly. The lens body will move.

2) Tilt the lens body down about 10° from the horizontal, and then turn the screw

clockwise to fasten it.

●

Assemble the assy-case front onto the case-rear as shown in the illustration. Fasten the assy-case front to the case-rear with the screw (BH M2.6) you removed earlier.

SCREW

BH M2. 6

CASE-REAR

ASSY-CASE FRONT

# Installing the Camera using the Mount-Corner

●

Choose an installation site that can sufficiently support 5 times the weight of the equipments to be installed.

●

Place the mount-corner to the corner to which you want to install the camera and mark screw holes with a pencil (indicated by the blue circles in the illustration). Drill a pilot hole for each pencil mark (5mm in diameter and at least 35mm in depth), and then fully insert the supplied plastic anchors (HUD 5) into them.

●

Install the mount-corner by aligning the four holes of the mount-corner to the holes of the plastic anchors, and then fastening the screw-tappings (BH M3 X 30).

SCREWTAPPING (BH M3 x 30)

SCREW-

TAPPING

(BH M3 x 30)

●

Remove the screw (BH M2.6) at the bottom of the main unit by turning it counterclockwise, and then lift the assy-case front as you push it upward to detach it from the case-rear. (❊Do not apply excessive force, as doing so may damage the inside

assembly.❊ )

●

Connecting Cables

1) Connecting the cables to the case-rear. Connect the RJ-11 cable to the RJ-11 connector on the case-rear and connect the camera cable to the cable terminal on the on the case-rear.

Assy-case front

Screw (BH M2.6)

CASE-REAR

2) Passing the cables through the hole on the mount-corner. Pass the cables through the hole on the mount-cornder as shown in the right picture below.

●

Assemble the case-rear onto the moun-tcorner by aligning the two holes of the case-rear to the protrusions of the mount-corner (indicated by the blue circles in the illustration) and fastening the screw-tappings (PH M3 X 16).

SCREW-TAPPING (PH M3 x 16)

●

Adjust the direction of the lens.

1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly.The lens body will move.

2) Tilt the lens body down about 10° from the horizontal, and then turn the screw clockwise to fasten it.

●

Assemble the assy-case front onto the caserear as shown in the illustration. Fasten the assy-case front to the case-rear with thescrew (BH M2.6) you removed earlier.

Screw

CASE-REAR

Screw (BH M2.6)

ASSY-CASE FRONT

1-4. Basic System Installation

Perform the following steps to install your system.

●

Take the monitor out of the packaging box.

●

Place the monitor where you would like to install it. Do not turn on power until installation is complete

●

Choose the place where you want to install the camera.

●

Once the monitor and camera locations have been chosen, install the camera.

●

Connect the cable to the jack on the back of the camera.

●

Connect the other end to CAMERA IN on the back of the monitor. (At this time, select the numbers and sequence of cameras.)

●

Connect the camera you wish to install (as shown below).

●

Connect the power cord of the monitor to the power outlet.

●

Power switch is on the rear panel of the monitor, and screen on switch is on the front panel of the monitor.

●

Initially the monitor is in the auto switching mode.

✳ After the power has been turned on, the CRT needs approximately 20 seconds of

stabilization period.

2. Connecting Peripheral Devices

2-1. Connecting a PIR Sensor

- An additional PIR sensor or external sensor can also be connected.

- The additional PIR sensor can be connected as shown in the above graphic.

- Sensor’s trigger signal is NO (Normal Open).

- Sensor is not supplied. (Sold separately)

2-2. Connecting a VCR

- Connect the VCR as shown below.

Camera alarm in

jack

Sensor

Sensor input

PIR sensor

3. Part Names and Functions

3-1. Standard Camera

Lens

It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area.

Microphone

Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor.

Camera fitting groove

Enables the camera to be fixed onto the bracket. You may install it either above or below the camera if necessary.

6-pin modular jack

Used to connect the camera to the monitor.

SENSOR jack

Used to connect the sensor to the camera.

Speaker

It outputs the sound signal which was transferred from the monitor.

PIN NUMBER SPEC

1 SPEAKER(HOT)

2 VIDEO_OUT

3 GND

4 SPEAKER(COLD)

5 AUDIO_OUT/ALARM_OUT

6 12V DC

Sensor Detection Angle & Area

< Vertical View Pattern>

Horizontal

View Pattern>

✳ Please consider the horizontal detection area and the vertical detection line when

choosing an installation site.

3-2. PIR Camera

Lens

It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area.

Speaker

It outputs the sound signal which was transfered from the monitor.

Fresnel Lens

An infrared focusing lens for increasing the sensitivity of the built-in PIR sensor.

6-pin modular jack

Used to connect the camera to the monitor.

PIN NUMBER SPEC

1 SPEAKER(HOT) 2 VIDEO_OUT 3 GND 4 SPEAKER(COLD) 5 AUDIO_OUT/ALARM_OUT 6 12V DC

5-pin Terminal jack

A terminal block for supplying backup power for the PIR sensor operation during power outages and for transmitting the relay signals to external devices during the PIR sensor operation.

Function Switch

A function switch for the PIR sensor operation.

PIR Sensor

A thermal heat sensor that detects infrared radiation projected by warm objects.

Microphone

Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor.

Electronic Relay

Output power is 350V/130mA.

PIN SPEC

1 Power Input DC 12 Volts 2 (Back Up) Ground 3 Not Used 4 Relay Output COM 5 (350v 130mA) N.C

5 432 1

OFF

S1 S2 S3 S4

PIN SPEC

Sensor Sensitivity

On, On : Low On, Off : Normal

2 Off, On : Normal

Off, Off : High 3 Alarm Led On/Off (Sensor On) 4 Sensor On/Off

3-3. Monitor Front

! BRIGHT

●

Adjust brightness with this knob.

@ CONT.

●

Adjust contrast with this knob.

# AUDIO

●

Adjust volume control for proper sound level.

$ H-HOLD

●

This control permits adjustment of horizontal stability.

% TALK/A.RESET

●

TALK : Talk to selected channel.

●

A.RESET : Reset Alarm.

^ VCR

●

This button is used to display recorded data in the VCR on the monitor.

& AUTO

●

This monitor normally will be in AUTO mode, which means it switches cameras automatically.

●

Press this button if you want to rescan camera port. This monitor will automatically skip the cameras that are not connected, and the ALARM mode is automatically activated in AUTO mode.

* CAMERA SELECT(C1~C4)

●

If you want press any camera selector button, this monitor goes into manual mode. Press AUTO button if you want to return to auto mode.

( ALARM/TIME

●

ALARM : Press this button if you wish to enable or disable an alarm. Initial

mode of monitor is alarm enable mode. (Red LED on : Alarm enabled)

●

TIME : Sequencing time(1 to 10 seconds) can be adjusted with this knob.

Go on pressing time button and press . Ex) if you go on pressing time button and press 1S, 2S, 3S, the

switching time of screen will be 6 second.

✳ The alarm function does not work for max 1 minute after turning on the camera.

) SCREEN ON/OFF

●

Turn the monitor screen ON/OFF. Even if the monitor is off, the system still works for recording. Vertical spot line can be shown when turn off this switch.

1 POWER LED

●

MAIN Power LED.

2 SPEAKER

3 MICROPHONE

28E29

3-4. Monitor Rear

! CAMERA IN (CAM1~CAM4)

●

Four input ports for four cameras. (6 Pin Modular Jack)

@ AUDIO IN/OUT//VIDEO IN/OUT

●

AUDIO IN/OUT : Audio in/out ports for VCR recording and playing.

●

VIDEO IN/OUT : Video in/out ports for VCR recording and playing.

# V-HOLD

●

Use to correct when the picture rolls up and down.

$ AC POWER CORD

●

Power cord.

% MAIN POWER

●

Main power switch.

●

When power on, initial mode is switching screen.

+ 70 hidden pages