Samsung SSA-S2000V User Manual

Standalone RFID Access Controller

User Manual

SSA-S2000V

Standalone RFID Access Controller

User Manual

Tra de mark

The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Tec hwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Warrant y

If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:

•

If the system behaves abnormally because you run a program irrelevant to the system operation.

•

Deteriorated performance or natural worn-out in process of time

•

Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)

is the registered logo of Samsung Techwin Co., Ltd.

safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To reduce the risk of ﬁ re or electric shock, do not expose this appliance to rain or moisture.

•

WARNING

Be sure to use only the standard adapter that is speciﬁ ed in the speciﬁ cation sheet.

1. Using any other adapter could cause ﬁ re, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause explosion, ﬁ re, electric shock, or damage to

2. the product.

Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or ﬁ re.

Securely plug the power cord into the power receptacle. Insecure connection may cause ﬁ re.

When installing the controller, fasten it securely and ﬁ rmly. The fall of controller may cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers ﬁ lled with water on top of the

6. controller. Doing so may cause personal injury due to ﬁ re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁ re or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the

8. power source and contact the service center. Continued use in such a condition may cause ﬁ re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in

9. any way. (SAMSUNG is not liable for problems caused by unauthorized modiﬁ cations or attempted repair.)

. When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁ re or electric shock.

10.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive

1. vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -30°C), or high humidity.

2. Doing so may cause ﬁ re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause ﬁ re or damage

4. to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁ re.

Install it in a place with good ventilation.

Avoid aiming the controller directly towards extremely bright objects such as sun.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as vases, shall be

8. placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

English _ 3

SAFETY INFORMATION

safety information

FCC Statement

Caution : Any changes or modiﬁ cations in construction of this device which are not expressly approved by the

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS

10.

11.

12.

13.

14.

4_ safety information

party responsible for compliance could void the user’s authority to operate the equipment.

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, any cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliﬁ ers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁ ed by the manufacturer.

Use only with cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus

combination to avoid injury from tip-over.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any

way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

contents

PRODUCT INTRODUCTION

INSTALLATION AND EXTERNAL

CONNECTION

INITIALIZATION

READER MODE SETUP

USER MANAGEMENT

7 Features 8 What’s included 9 At a Glance 10 Cable Color Scheme

11 Cable Selection 12 Bypass Diode Connection 12 I/O Connection 14 External Reader Connection

15 Basic Operations 16 Initialization 16 Forced Initialization with External Line

17 Reader Mode Setup (RF ONLY) 18 Reader Mode Setup (RF + P/W) 18 Reader Mode Setup (PIN ONLY) 19 Reader Mode Setup (RF/PIN Combination

Mode)

19 Enabling Keypad Input for the Card Number

20 To register cards in RF ONLY mode 20 RegIsterIng cards In a combInatIon of RF and

P/W modes

21 To regIster cards In PIN mode 21 RegIsterIng cards In RF card / PIN

combInatIon mode

22 To delete a regIstered card or PIN number

CONTENTS

BASIC SETUP

23 Duress Alarm 23 To specify the retry count for an unregistered

24 To specify the keypad input suspension time

if the retry count with an unregistered ID exceeds the limit

24 To specify the delayed start time in Secure

mode

25 To specify the operation time of the Door

Contact Sensor

25 To specify the limited time for the keypad

input

26 To specify the alarm output port for the

dismantled device

26 To open or close the entry door 27 To set or release the QUICK mode 27 To set or release the Toggle mode for the

door relay

English _ 5

contents

I/O TIME SETUP

ADVANCED SETTING

ADDITIONAL FEATURES

28 To specify the output time if the card is

authenticated

29 To specify the output time if the card is not

authenticated

29 To specify the Duress TTL output 30 To specify the alarm output for an input error

of the Door contact Sensor

30 To specify the alarm operation time for AUX 1 31 To specify the alarm operation time for AUX 2 31 To specify the alarm operation time for AUX 3 32 To activate or deactivate the door relay by

the Door Contact Sensor

33 To specify the TTL output operation mode 33 To set the chime bell function 34 To specify the chime bell operation time 34 To specify the input mode for AUX 1 35 To specify the input mode for AUX 2 35 To specify the input mode for AUX 3 36 To specify the input mode for the Exit Button 36 To specify the input mode for the Door

Contact Sensor

37 Mute 37 To specify the use of the tamper alarm 38 To check the output speciﬁ ed for a registered

card user

38 To check the output speciﬁ ed for an

unregistered card user

39 To check the output speciﬁ ed for the Door

Contact Sensor alarm

39 To check the output speciﬁ ed for AUX 1 40 To check the output speciﬁ ed for AUX 2 40 To check the output speciﬁ ed for AUX 3

6_ contents

OTHER INFORMATION

TROUBLESHOOTING

PRODUCT SPECIFICATIONS

41 InItIal Values 42 FunctIon codes

44 Troubleshooting

49 product speciﬁ cations

product introduction

FEATURES

This controller is best designed for a single entry door control (single door access control). This product can save up to 512 cards including the master card, with which you can make an effective management

(such as adding, deleting or changing the settings) of the cards. Its epoxy adhesion and aluminium case guarantees shock-resistance and stable operation in a challenging environment.

This product features 5 external ports that can be connected to the Exit button, Door Contact Sensor, Motion Sensor, and Fire Sensor. It also has 2 relay outputs that can control the door lock and alarm relay. The dual tamper switch triggers an alert if the product is forcibly disassembled.

You can use the keypad to conﬁ gure all settings as necessary. This product is designed for a standalone system.

Single Door Access Control

You can use the RF card (SSA-C100,SSA-C110,SSA-C120) to control a single door.

User Registration

You can register a total of 512 cards including the Master Card.

Keypad Registration

SSA-S2000V is equipped with the built-in keypad that you can use to register, delete cards or conﬁ gure various settings independently.

Buzzer On/Off

With the help of various buzzer tones, you can check the operation status and the current settings and results of the product.

PRODUCT INTRODUCTION

External I/O Pins

SSA-S2000V has 5 input ports and 4 output ports installed (2 relay and 2 TTL outputs). The input ports can receive signals from the Exit button and the Door Contact sensor, while the two relays can be connected to the door lock and the alarm device. One of the TTL output ports can function as a chime bell in connection with the door bell.

Duress Alarm

This is used in a situation where you should open the door inevitably by a robber insisting to do so. Entering the two-digit duress alarm password with pressing the the door normally, while you can set to produce the TTL signal notifying the door is forcibly opened.

button and recognizing the registered card (or card number) can open

Limited Access Tries for an Unregistered Card

You can specify the limit of times to try accessing the door, and the suspended operation time of the keypad for an improper access.

English _ 7

product introduction

WHAT’S INCLUDED

Check if the following items are included in the product package.

SSA-S2000V

Main Unit

Quick Guide

3mm Hex Wrench (x1)

3.5 x 40mm Screws (x4)

3.5 x 25mm Screws (x4)

6 x 30mm Plastic Anchors (x4)

Diodes (x2)

(UF4004, 1N4001~4007)

CD Manual

tGj

Master Card (x1)

8_ product introduction

AT A GLANCE

Front/Rear

PRODUCT INTRODUCTION

SSA-S2000V

System Status LED

Keypad

TAMPER SWITCH

17-PIN Connector

Buzzer

Fixing Hole

Indicates the operation status of the system.

Use this to conﬁ gure or release settings as appropriate, or enter a card number.

A tamper switch to detect falling from the wall.

Used to connect to the power source or I/O cable.

Piezo buzzer.

Fixing hole for wall-mounting.

English _ 9

product introduction

CABLE COLOR SCHEME

Item Cable Color Signal Line Description

Power

Output

Input

Red DC +12V Power (+12V)

Black GND(-) Earth-grounding for power

Blue with white stripes NC(RL1) Door Relay NC Terminal

Gray with red stripes COM(RL1) Door Control Relay (COM) Port

White with red stripes NO(RL1) Door Relay NO port

Purple with white stripes NC(RL2) Alarm Relay (NC) Port

White COM(RL2) Alarm Relay (COM) Port

Purple NO(RL2) Alarm Relay (NO) Port

Orange with white stripes TTL TTL Output Port

Brown with white stripes CHI Chime Bell Output

Orange EXIT

Yellow with red stripes CONTACT

Green AUX IN 1 Aux Input #1

Green with white stripes AUX IN 2 Aux Input #2

Green with red stripes AUX IN 3 Aux Input #3

Pink DATA_0 Wiegand Data 0 Input Port

Exit button connection port

Door Contact Sensor Connection Port

Sky blue DATA_1 Wiegand Data 1 Input Port

10_ product introduction

Cable Type

Belden #9409, 18 AWG 2 Conductor, Unshielded

installation and external connection

CABLE SELECTION



INSTALLATION AND EXTERNAL CONNECTION

DC12V

SSA-S2000V

  

Power Supply

RF Reader Lock/Alarm

Item

Power (DC12V)

DC Power  This Product

Reader (power and data)

External Reader  This Product

Door Contact Sensor Exit Button

Sensor Input Input  This Product

Door Lock,

Alarm Device

Lock (Alarm)  This Product

The cables should be thick enough to allow the maximum current consumed by the reader.



Sensor Input

Belden #9409, 18 AWG 2 Conductor, Unshielded

Belden #9512, 22 AWG 4 Conductor, Shielded

Belden #9514, 22 AWG 8 Conductor, Shielded

Belden #9512, 22 AWG 4 Conductor, Shielded

Belden #9514, 22 AWG 8 Conductor, Shielded

Belden #9409, 18 AWG 2 Conductor, Unshielded

Cable Type

English _ 11

installation and external connection

BYPASS DIODE CONNECTION

If you connected an inductor (door locks or alarm device) to the output relay, there should occur a voltage surge while the inductor is turning on and off. If you do not connect a reverse diode to the relay, the surge voltage will cause damage to the electric circuit of the controller. To reduce this surge, it is recommended to connect a reverse diode between the devices.

SSA-S2000V

I/O CONNECTION

Input Connection

Door Contact Sensor

Exit Button

PUSH

SSA-S2000V

DC+

DC-

Lock/Alarm

Door Contact Sensor: Green with red stripes, GND Exit Button: Orange line, GND

Black-

Red+

Cathode Anode

1N4004 ~ 1N4007 or equiv.

DC + 12V

Power Supply

Connect the DC 12V(+) of the power supply unit to the red line.

Connect the GND(-) of the power supply unit to the black line.

- Exit Button Connection

Connect one line of the Exit button to the orange line.

Connect the other line of the Exit button to GND.

- Door Contact Sensor Connection

Connect one line of the door contact sensor to the yellow with red stripes.

Connect the other line of the door contact sensor to GND.

- Auxiliary Input Device Connection (AUX 1 (green), AUX 2 (green with white stripes), AUX 3 (green with red stripes)

Connect one line of the external input device to AUX 1, AUX 2, or AUX 3.

Connect the other line of the external input device to GND(-).

12_ installation and external connection

Output Connection

DOOR RELAY

DOOR LOCK

SSA-S2000V

DOOR

RELAY

COM

Cathode

1N4004~1N4007 or equiv.

Anode

EXIT

CONTACT

AUX IN#1

CHIME

+12V

ALARM RELAY

COM

ALARM RELAY

SIREN

GND

DC 12V

POWER

SUPPLY

PIR SENSOR

GND+12V

CHIME BELL

EXIT

BUTTON

DOOR

CONTACT

- Door open (POWER FAIL SAFE) when the power is disconnected from the door lock (Door Relay)

Connect the relay COM line (gray with red stripes for locking the door) to DC +12V.

Connect the relay NC line (blue with white stripes for locking the door) to the plus(+) line of the door lock.

Connect the minus (-) line of the door lock to GND (-).

- Door close (POWER FAIL SECURE) when the power is disconnected from the door lock (Door Relay)

Connect the relay COM line (gray with red stripes for locking the door) to DC +12V.

Connect the relay NO line (white with red stripes for locking the door) to the plus (+) line of the door lock.

Connect the minus (-) line of the door lock to GND (-).

- Alarm Connection (Alarm Relay)

Connect the relay COM (white for the alarm device) to DC +12V.

Connect the relay NO line (purple for the alarm device) to the plus (+) line of the alarm device.

Connect the minus (-) line of the alarm device to GND (-).

- Chime Bell Connection (the chime bell operated by TTL-level signal must be installed in advance.)

Connect the chime bell line (brown with white stripes) of the controller to DC +5V.

Connect the GND line of the power supply unit to GND (-) of the chime bell.

Press

to a0ctivate EthNeT chime bell.

INSTALLATION AND EXTERNAL CONNECTION

English _ 13

installation and external connection

EXTERNAL READER CONNECTION

Wiegand DATA0(Pink)

Wiegand DATA0(Sky blue)

SSA-S2000V

GND

Black-

Red+

DC+12V

- Proximity Reader Connection

Connect the DC 12V(+) of the power supply unit to the plus (+) line of the reader.

Connect the GND(-) line of the power supply unit to the minus (-) line of the reader.

Connect the Wiegand data input line 0 of the proximity reader to the purple line.

Connect the Wiegand data input line 1 of the proximity reader to the sky blue line.

•

For a list of compliant readers (external readers), see the followings:

- Standard 26bit Wiegand format proximity reader

- Proximity/keypad readers of 4-/8-bit burst format are not supported.

(+)

(-)

14_ installation and external connection

initialization

BASIC OPERATIONS

Initial Status

While the product is working normally, the orange LED indicator blinks every one second.

Predeﬁ ned Operation for a Registered Card

When reading a registered card, it opens the door with the melody.

Exit Button Operation

If you press the Exit button, the door will be opened.

Predeﬁ ned Operation for an Unregistered Card

When reading an unregistered card, it produces an alarm with the melody for two seconds. You can specify the use of the alarm and change the operation time.

Secure Mode Operation

The person who exits the last can set the secure mode using the keypad.

Set Secure mode: Press the Release secure mode: Present and authenticate a registered card or the Master Card to the reader. You can use

the keypad to specify the delayed start time for the Secure mode. (Refer to the delayed start time in Secure mode on page 24.)

button twice and press .

INITIALIZATION

t

Gj



SSA-S2000V

EXI

For effective security purposes, you can set to activate the sensors (via auxiliary input ports) only in Secure mode.



Duress Alarm

If you are forced to open the door under a robber’s control, enter the Duress password and press with the number of your registered card (or PIN). (See page 23.)

How to use the chime bell

When you have connected and set the chime bell, press to ring the chime bell. (See page 33.)

English _ 15

+ 35 hidden pages

Samsung SSA-S2000V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual