Refrigerator
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
Free Standing Appliance
DA68-03194H (EN)-06.indd 1 2016. 3. 24. �� 3:21
Contents
SAFETY INFORMATION ……………………………………………………… 2
SETTING UP YOUR REFRIGERATOR …………………………………… 18
OPERATING YOUR SAMSUNG REFRIGERATOR ……………………… 27
TROUBLESHOOTING ……………………………………………………… 40
Safety information
SAFETY INFORMATION
• Before operating the
appliance, please read this
manual thoroughly and retain
it for your reference.
• Use this appliance only for
its intended purpose as
described in this instruction
manual.
This appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory
or mental capabilities or
lack of experience and
knowledge if they have
been given supervision or
instruction concerning use of
the appliance in a safe way
and understand the hazards
involved.
Children shall not play with
the appliance.
Cleaning and user
maintenance shall not be
made by children without
supervision.
• Warnings and Important
Safety Instructions in this
English - 2
DA68-03194H (EN)-06.indd 2 2016. 3. 24. �� 3:21
manual do not cover all
possible conditions and
situations that may occur.
It is your responsibility to use
common sense, caution,
and care when installing,
maintaining, and operating
your appliance.
• Because these following
operating instructions
cover various models,
the characteristics of your
refrigerator may dier slightly
from those described in this
manual.
R-600a or R-134a is used as
a refrigerant.
Check the compressor label
on the rear of the appliance
or the rating label inside the
fridge to see which refrigerant
is used for your refrigerator.
When this product contains
flammable gas (Refrigerant
R-600a), contact your local
authority in regard to safe
disposal of this product.
refrigerant used.
• Never start up an appliance
showing any signs of
damage.
If in doubt, consult your
dealer.
The room must be 1m³
in size for every 8g of
R-600a refrigerant inside the
appliance.
The amount of refrigerant in
your particular appliance is
shown on the identification
plate inside the appliance.
• Refrigerant squirting out of
the pipes could ignite or
cause an eye injury.
When refrigerant leaks from
the pipe, avoid any naked
flames and move anything
flammable away from the
product and ventilate the
room immediately.
- Failing to do so may result in
fire or explosion.
SAFETY INFORMATION
• In order to avoid the
creation of a flammable gasair mixture if a leak in the
refrigerating circuit occurs,
the size of the room in which
the appliance may be sited
depends on the amount of
English - 3
DA68-03194H (EN)-06.indd 3 2016. 3. 24. �� 3:21
Important safety symbols
and precautions:
Hazards or unsafe
practices that may result
WARNING
in severe personal
injury or death.
Hazards or unsafe
practices that may result
CAUTION
in minor personal
injury or property
damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug
from the wall socket.
Make sure the machine
is grounded to prevent
electric shock.
Call the contact center for
help.
Note.
These warning signs are
here to prevent injury to you
and others.
Please follow them carefully.
After reading this section,
keep it in a safe place for
future reference.
SEVERE WARNING
WARNING
SIGNS FOR
TRANSPORTATION
AND SITE
• When transporting
and installing the
appliance,care should be
taken to ensure that no
parts of the refrigerating
circuit are damaged.
- Refrigerant leaking from the
pipe work could ignite or
cause an eye injury.
If a leak is detected, avoid
any naked flames or potential
sources of ignition and air the
room in which the appliance
is standing for several
minutes.
- This appliance contains a
small amount of isobutane
refrigerant (R-600a), a natural
gas with high environmental
compatibility that is, however,
also combustible.
When transporting and
installing the appliance,
care should be taken to
ensure that no parts of
the refrigerating circuit are
damaged.
English - 4
DA68-03194H (EN)-06.indd 4 2016. 3. 24. �� 3:21
SEVERE WARNING
WARNING
SIGNS FOR
INSTALLATION
• Deteriorated insulation
of electrical parts may
cause an electric shock
or fire.
• Do not place this refrigerator
in direct sunlight or expose to
the heat from stoves, room
heaters or other appliance.
• Do not plug several
appliances into the same
multiple power board.
The refrigerator should
always be plugged into its
own individual electrical outlet
which has a voltage rating
that matched the rating plate.
- This provides the best
performance and also
prevents overloading house
wiring circuits, which could
cause a fire hazard from
overheated wires.
• If the wall socket is loose, do
not insert the power plug.
- There is a risk of electric
shock or fire.
• Do not use a cord that shows
cracks or abrasion damage
along its length or at either
end.
English - 5
• Do not pull or excessively
bend the power cord.
• Do not twist or tie the power
cord.
• Do not hook the power cord
over a metal object, place a
heavy object on the power
cord, insert the power cord
between objects, or push the
power cord into the space
behind the appliance.
- When moving the refrigerator,
be careful not to roll over or
damage the power cord.
- This may result in an electric
shock or fire.
• Do not use aerosols near the
refrigerator.
- Aerosols used near the
refrigerator may cause an
explosion or fire.
- Do not bend the power cord
excessively or place heavy
articles on it.
• This refrigerator must be
properly installed and
located in accordance
with the manual before it
is used.
• Do not install the refrigerator
in a damp place or place
where it may come in contact
with water.
SAFETY INFORMATION
DA68-03194H (EN)-06.indd 5 2016. 3. 24. �� 3:21
- Deteriorated insulation of
electrical parts may cause an
electric shock or fire.
• Connect the power plug in
proper position with the cord
hanging down.
- If you connect the power
plug upside down, wire can
get cut o and a cause fire or
an electric shock.
• Do not install this appliance
in a humid, oily or dusty
location, in a location
exposed to direct sunlight
and water (rain drops).
• Do not install this appliance
in a location where gas may
leak.
- This may result in an electric
shock or fire.
• Make sure that the power
plug is not squashed or
damaged by the back of the
refrigerator.
• When moving the refrigerator,
be careful not to roll over or
damage the power cord.
- This constitutes a fire hazard.
• Keep the packing materials
out of reach of children.
- There is a risk of death from
suocation if children put
them on their head.
• This appliance should be
positioned in such a way that
it is accessible to the power
plug.
- Failing to do so may result in
an electric shock or fire due
to electric leakage.
• Do not install this appliance
near a heater, inflammable
material.
English - 6
• If any dust or water is in the
refrigerator, pull out power
plug and contact your
Samsung Electronics service
center.
- Otherwise there is a risk of
fire.
• Do not stand on top of the
appliance or place objects
(such as laundry, lighted
candles, lighted cigarettes,
dishes, chemicals, metal
objects, etc.) on the
appliance.
- This may result in an electric
shock, fire, problems with the
product, or injury.
• This appliance must be
properly grounded.
• Do not ground the appliance
to a gas pipe, plastic water
pipe, or telephone line.
- You must ground the
DA68-03194H (EN)-06.indd 6 2016. 3. 24. �� 3:21
refrigerator to prevent any
power leakages or electric
shocks caused by current
leakage from the refrigerator.
- This may result in an electric
shock, fire, explosion, or
problems with the product.
- Never plug the power cord
into a socket that is not
grounded correctly and make
sure that it is in accordance
with local and national codes.
• If the power cord is
damaged, have it
replaced immediately by
the manufacturer or its
service agent.
• The fuse on the refrigerator
must be changed by a
qualified technician or service
company.
- Failing to do so may result in
an electric shock or personal
injury.
CAUTION SIGNS FOR
CAUTION
INSTALLATION
• Keep ventilation
opening in the appliance
enclosure or mounting
structure clear of
obstruction.
• Allow the appliance to stand
for 2 hours before loading
foods after installation and
turning on.
• The installation or any
service of this appliance
is recommended by a
qualified technician or service
company.
- Failing to do so may result
in an electric shock, fire,
explosion, problems with the
product, or injury.
• When installing the
refrigerator, make sure both
legs contact the floor for
secure installation.
Legs are located at the
bottom back of freezer door.
Insert a flathead screwdriver
and turn it in the direction of
the arrow until it is level.
SAFETY INFORMATION
• Always balance the load on
each door.
• Overload on any one door
may fell the refrigerator,
causing physical injury.
English - 7
DA68-03194H (EN)-06.indd 7 2016. 3. 24. �� 3:21
SEVERE WARNING
WARNING
SIGNS FOR USING
• Do not touch the power
plug with wet hands.
- This may result in an electric
shock.
• Do not store articles on the
top of the appliance.
- When you open or close the
door, the articles may fall and
cause a personal injury and/
or material damage.
• Do not put items filled with
water on the refrigerator.
- If spilled, there is a risk of fire
or electric shock.
• Do not touch the inside walls
of the freezer or products
stored in the freezer with wet
hands.
- This may cause frostbite.
• Do not use or place any
substances sensitive
to temperature such
as inflammable sprays,
inflammable objects, dry ice,
medicine, or chemicals near
the refrigerator.
Do not keep volatile or
inflammable objects or
substances (benzene,
thinner, propane gas, alcohol,
ether, LP gas and other
such products etc.) in the
refrigerator.
- This refrigerator is for storing
food only.
- This may result in a fire or an
explosion.
• Do not store pharmaceuticals
products, scientific materials
or temperature-sensitive
products in the refrigerator.
- Products that require
strict temperature controls
must not be stored in the
refrigerator.
• Do not place or use
electrical appliance inside
the refrigerator/freezer,
unless they are of a type
recommended by the
manufacturer.
• If you smell pharmaceutical
or smoke, pull out power
plug immediately and contact
your Samsung Electronics
service center.
• If any dust or water is in
Refrigerator, pull out power
plug and contact your
Samsung Electronics service
center.
- Otherwise there is a risk of
fire.
• If gas leak is detected, avoid
English - 8
DA68-03194H (EN)-06.indd 8 2016. 3. 24. �� 3:21
any naked flames or potential
sources of ignition and air the
room in which the appliance
is standing for several
minutes.
• Do not use mechanical
devices or any other means
to accelerate the defrosting
process, other than those
recommended by the
manufacturer.
• Do not damage the
refrigerant circuit.
• Do not spray volatile material
such as insecticide onto the
surface of the appliance.
- As well as being harmful to
humans, it may also result
in an electric shock, fire or
problems with the product.
• Do not use a hair dryer to dry
the inside of the refrigerator.
Do not place a lighted
candle in the refrigerator for
removing bad odours.
- This may result in an electric
shock or fire.
• Fill the water tank, ice tray,
water cubes only with
potable water.
- Do not fill tea or sports drink,
this may cause the damage
of refrigerator.
• Do not let children hang on
the door.
If not, a serious injury may
occur.
- Risk of children entrapment.
Do not let children enter
inside the refrigerator.
• Do not leave the doors of
the refrigerator open while
the refrigerator is unattended
and do not let children enter
inside the refrigerator.
• Do not allow babies or
children go inside the drawer.
- It can cause death from
suocation by entrapment or
personal injury.
• Do not sit on the Freezer
door.
- The door may be broken and
cause a personal injury.
• To prevent children
entrapment, you must
reinstall the divider using
provided screws after
cleaning or other actions if
you removed the divider from
the drawer.
• Do not use mechanical
devices or any other means
to accelerate the defrosting
process, other than those
recommended by the
SAFETY INFORMATION
English - 9
DA68-03194H (EN)-06.indd 9 2016. 3. 24. �� 3:21
manufacturer.
• Do not damage the
refrigerant circuit.
• In the event of a gas leak
(such as propane gas,
LP gas, etc.), ventilate
immediately without
touching the power plug.
Do not touch the
appliance or power cord.
- Do not use a ventilating fan.
- A spark may result in an
explosion or fire.
• Use only the LED Lamps
provided by manufacturer or
service agent.
• Children should be
supervised to ensure that
they do not play with the
appliance.
tightly together so that they
do not fall out.
• This product is intended only
for the storage of food in a
domestic environment.
• Never put fingers or other
objects into the dispenser
hole, ice chute and ice maker
bucket.
- It may cause a personal injury
or material damage.
• Do not insert hands, feet
or metal objects (such as
chopsticks, etc.) into the
bottom or the back of the
refrigerator.
- This may result in an electric
shock or injury.
- Any sharp edges may cause
a personal injury.
• Keep fingers out of “pinch
point” areas; clearances
between the doors and
cabinet are necessarily small.
• Do not let children hang on
the door.
If not, a serious injury may
occur.
• There is a Risk of children
entrapment.
Do not let children enter
inside the refrigerator.
• Do not attempt to repair,
disassemble, or modify
the appliance yourself.
- Do not use any fuse (such as
cooper, steel wire, etc.) other
than the standard fuse.
- When repairing or reinstalling
the appliance is required,
contact your nearest service
center.
- Failing to do so may result
in an electric shock, fire,
• Bottles should be stored
English - 10
DA68-03194H (EN)-06.indd 10 2016. 3. 24. �� 3:21
problems with the product,
or injury.
• If the appliance
generates a strange
noise, a burning or smell
or smoke, unplug the
power plug immediately
and contact your nearest
service center.
- Failing to do so may result in
an electric or fire hazards.
• Pull the power plug out of
the socket before changing
the interior lamps of the
refrigerator
- Otherwise, there is a risk of
electric shock.
• If you experience diculty
when changing the light,
contact service agent.
• If the products is equipped
with the LED Lamp, do not
disassemble the Lamp Cover
and LED Lamp by yourself.
- Please contact your service
agent.
• Plug the power plug into the
wall socket firmly.
Do not use a damaged
power plug, damaged power
cord or loose wall socket.
- This may result in an electric
shock or fire.
English - 11
• Do not put a container filled
with water on the appliance.
- If spilled, there is a risk of fire
or electric shock.
• Never stare directly at the UV
LED lamp for long periods of
time.
- This may result in eye strain
due to the ultraviolet rays.
CAUTION SIGNS FOR
CAUTION
USING
• To get best performance
from the product,
- Do not place foods too
closely in front of the vents
at the rear of the appliance
as it can obstruct free air
circulation in the refrigerator
compartment.
- Wrap the food up properly or
place it in airtight containers
before putting it into the
refrigerator.
- Do not put any newly
introduced food for freezing
near to already existing food.
• Do not place glass or bottles
or carbonated beverages into
the freezer.
- The container may freeze and
break, and this may result in
injury.
SAFETY INFORMATION
DA68-03194H (EN)-06.indd 11 2016. 3. 24. �� 3:21
• Please observe maximum
storage times and expiry
dates of frozen goods.
• Do not store low
temperature-sensitive
pharmaceutical products,
scientific materials or other
low temperature-sensitive
products in the refrigerator.
- Products that require
strict temperature controls
must not be stored in the
refrigerator.
• There is no need to
disconnect the refrigerator
from the power supply if you
will be away for less than
three weeks.
But, remove all the food if
you are going away for the
three weeks or more.
Unplug the refrigerator and
clean it, rinse and dry.
• Do not place carbonated
or fizzy drinks in the freezer
compartment.
Do not put bottles or glass
containers in the freezer.
- When the contents freeze,
the glass may break and
cause personal injury and
property damage.
• Do not modify the refrigerator.
Unauthorized modifications
English - 12
can cause safety problems.
To reverse an unauthorized
modification, we will charge
the full cost of parts and
labor.
• Do not change or modify
the functionality of the
refrigerator.
- Changes or modifications
may result in a personal injury
and/or property damage.
Any changes or modifications
performed by a 3rd party on
this completed appliance
are neither covered under
Samsung warranty service,
nor is Samsung responsible
for safety issues and
damages that result from 3rd
party modifications.
• Do not block air holes.
- If the air holes are blocked,
especially with a plastic bag,
the refrigerator can be over
cooled.
If this cooling period lasts
too long, the water filter
may break and cause water
leakage.
• Use only the ice-maker
provided with the refrigerator.
• The water supply to this
refrigerator must only be
installed/connected by a
DA68-03194H (EN)-06.indd 12 2016. 3. 24. �� 3:21
suitably qualified person and
connected to a potable water
supply only.
• If you have a long vacation
or business trip and won’t
use water or ice dispensers,
close the water valve.
- Otherwise, water leakage
may occur.
• Wipe excess moisture from
the inside and leave the
doors open.
- Otherwise, odor and mold
may develop.
• When the refrigerator got
wet by water, pull out the
power plug and contact your
Samsung Electronics service
center.
• Do not apply strong shock
or excessive force onto the
surface of glass.
- Broken glass may result
in a personal injury and/or
property damage.
• Do not sit on or hang onto
the door or home bar of
refrigerator.
- This may cause the
refrigerator to fall over, the
door to separate or a hand
being caught in the crack of
the door, and this may result
in property damage or injury.
• If the supply cord is
damaged, it must be
replaced by the manufacturer,
its service agent or similarly
qualified persons in order to
avoid a hazard.
CAUTION SIGNS
CAUTION
FOR CLEANING AND
MAINTENANCE
• Do not spray cleaning
products directly on the
display.
- Printed letters on the display
may come o.
• If any foreign substance
such as water has entered
the appliance, unplug the
power plug and contact your
nearest service center.
- Failing to do so may result in
an electric shock or fire.
• Remove all foreign
substances such as dust or
water from the power plug
terminals and contact points
using a dry cloth on a regular
basis.
- Unplug the power plug and
clean it with a dry cloth.
- Failing to do so may result in
an electric shock or fire.
SAFETY INFORMATION
English - 13
DA68-03194H (EN)-06.indd 13 2016. 3. 24. �� 3:21
• Do not clean the appliance
by spraying water directly
onto it.
• Do not use benzene, thinner,
or Clorox, Chloride for
cleaning.
- They may damage the
surface of the appliance and
may cause a fire.
• Before cleaning or
performing maintenance,
unplug the appliance
from the wall socket.
- Failing to do so may result in
an electric shock or fire.
SEVERE WARNING
WARNING
SIGNS FOR
DISPOSAL
• Leave the shelves in
place so that children
may not easily climb
inside.
• Ensure that none of the
pipes on the back of the
appliance are damaged prior
to disposal.
• R-600a or R-134a is used as
a refrigerant.
Check the compressor label
on the rear of the appliance
or the rating label inside the
refrigerator to see which
refrigerant is used for your
refrigerator.
When this product contains
flammable gas (Refrigerant
R-600a), contact your local
authority in regard to safe
disposal of this product.
Cyclopentane is used as an
insulation blowing gas.
The gases in insulation
material require special
disposal procedure.
Please contact your local
authorities in regard to the
environmentally safe disposal
of this product.
Ensure that none of the pipes
on the back of the appliances
are damaged prior to
disposal.
The pipes shall be broken in
the open space.
• It is hazardous for anyone
other than an Authorised
Service Person to service this
appliance.
In Queensland – the
authorized Service Person
MUST hold a Gas Work
Authorisation or Licence for
hydrocarbon refrigerants, to
carry out Servicing or repairs
which involve the removal of
English - 14
DA68-03194H (EN)-06.indd 14 2016. 3. 24. �� 3:21
covers. (For Australia only)
• When disposing of this or
other refrigerator/s, remove
the door/door seals, door
latch so that children or
animals cannot become
trapped inside.
Children should be
supervised to ensure that
they do not enter and play
with the appliance.
- If trapped inside, the child
may become injury and
suocate to death.
• Please dispose of the
packaging material for this
product in an environmentally
friendly manner.
• Keep all packaging materials
well out of the reach of
children, as packaging
materials can be dangerous
to children.
- If a child places a bag over
its head, it may result in
suocation.
English - 15
ADDITIONAL TIPS
FOR PROPER USAGE
• In the event of a power
failure, call the local oce of
your Electricity Company and
ask how long it is going to
last.
- Most power failures that are
corrected within an hour
or two will not aect your
refrigerator temperatures.
However, you should
minimize the number of door
openings while the power is
o.
- But should the power failure
last more than 24 hours,
remove all frozen food.
• If keys are provided with the
refrigerator, the keys should
be kept out of the reach of
children and not be in the
vicinity of the appliance.
• The appliance might
not operate consistently
(possibility of defrosting of
contents or temperature
becoming too warm in the
frozen food compartment)
when sited for an extended
period of time below the
cold end of the range of
temperature for which the
refrigerating appliance is
SAFETY INFORMATION
DA68-03194H (EN)-06.indd 15 2016. 3. 24. �� 3:21
designed.
• In case of particular foods,
keeping it under refrigeration
can have a bad eect on
preservation due to its
properties.
• Your appliance is frost free,
which means there is no
need to manually defrost
your appliance, as this will be
carried out automatically.
• Temperature rise during
defrosting can comply with
ISO requirements.
But if you want to prevent an
undue rise in the temperature
of the frozen food while
defrosting the appliance,
please wrap the frozen
food up in several layers of
newspaper.
• Any increase in temperature
of frozen food during
defrosting can shorten its
storage life.
• Do not re-freeze frozen foods
that have thawed completely.
Saving Energy Tips
- Install the appliance in a
cool, dry room with adequate
ventilation.
Ensure that it is not exposed
to direct sunlight and never
put it near a direct source of
heat (radiator, for example).
- Not to block any vents and
grilles is recommended for
energy eciency.
- Allow warm food to cool
down before placing it in the
appliance.
- Put frozen food in the
refrigerator to thaw.
You can then use the low
temperatures of the frozen
products to cool food in the
refrigerator.
- Do not keep the door of
the appliance open for too
long when putting food in or
taking food out.
The shorter time for which
the door is open, the less ice
will form in the freezer.
- Allow clearance to the right,
left, back and top when
installing.
This will help reduce power
consumption and keep your
energy bills lower.
- For the most ecient use
English - 16
DA68-03194H (EN)-06.indd 16 2016. 3. 24. �� 3:21
of energy, please keep the
all inner fittings such as
baskets, drawers, shelves
on the position supplied by
manufacturer.
This appliance is intended
to be used in household and
similar applications such as
- sta kitchen areas in shops,
oces and other working
environments;
- farm houses and by clients
in hotels, motels and other
residential type environments;
- bed and breakfast type
environments;
SAFETY INFORMATION
- catering and similar non-retail
applications.
English - 17
DA68-03194H (EN)-06.indd 17 2016. 3. 24. �� 3:21
Setting up your refrigerator
GETTING READY TO INSTALL THE
REFRIGERATOR
Congratulations on your purchase of the Samsung
refrigerator.
We hope you enjoy the state-of-art features and
eciencies that this new appliance oers.
Selecting the best location for the
Refrigerator
Choose :
• A location with easy access to the water supply.
• A location without direct exposure to sunlight.
• A location with level (or nearly level) flooring.
• A location with enough space for the refrigerator
doors to open easily.
• A location that allows sucient space to the
right, left, back, and top for air circulation.
If the refrigerator does not have enough space,
it can cause the bad influence to refrigeration
eciency and power consumption.
• A location that allows you to move the
refrigerator easily if it needs maintenance or
service.
• Do not install the refrigerator in locations where
the temperature is over 43°C (110°F) or below
5°C (41°F).
B
B
AA
D
125
43mm
D
°
305.5mm
1075mm
C
C
Depth “A” 733mm
Width “B” 908mm
Height “C” 1797mm
Overall Height “D” 1825mm
50mm
300mm 300mm
°
125
1519mm
908mm
72.3mm
610mm
• Each measurement based on the design
dimension, so it may dier depending on
the measuring method.
English - 18
DA68-03194H (EN)-06.indd 18 2016. 3. 24. �� 3:21
When moving your refrigerator
To prevent floor damage, be sure the front leveling
legs are in the up position (above the floor).
Refer to “HOW TO LEVEL THE REFRIGERATOR” in
the manual on page 23.
REMOVING THE REFRIGERATOR
DOORS
If the refrigerator is too large to pass through your
doorway easily, you can remove the refrigerator
doors.
Flooring
For proper installation, you must place this
refrigerator on a level, hard surface that is the same
height as the rest of the floor.
This surface should be strong enough to support a
fully loaded refrigerator.
To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working.
When moving the refrigerator, you need to pull and
push it straight forwards or back.
Do not wiggle it from side to side.
Tools you will need (Not provided)
Philips screwdriver
(+)
Pliers
• Disconnect power to the refrigerator
CAUTION
before removing the doors or drawers.
• Be careful not to drop, damage or
scratch the doors/drawers while
removing them.
• Use care when you remove the doors/drawers.
The doors are heavy and you could injure
yourself.
• Re-attach the doors/drawers properly to avoid:
- Moisture from air leakage.
- Uneven door alignment.
- Wasting energy due to improper door seal.
Flat-blade
screwdriver (-)
Allen wrench
(4mm)
Socket wrench
(10mm)
Allen wrench
(5mm)
SETTING UP
English - 19
DA68-03194H (EN)-06.indd 19 2016. 3. 24. �� 3:21
DISASSEMBLING THE FRIDGE
DOORS
1. With the door closed, remove the 3 screws
holding the Top Cover (A) with a Phillips (+)
Screwdriver, and then remove the Top Cover
with the entire wire-harnesses attached.
A
2. Separate the two connectors on the left door
and the one connector on the right door. (B)
Press the white sleeve (C) of the Water Tube
Coupler, and then separate the Water Tube (D).
B
B
D
C
4. Remove the Hinge (F).
F
5. Lift up the Fridge Door and take it o.
• While disassembling and reassembling
CAUTION
the door, make sure that the electric
wires are not peeled o.
• Do not let the door fall down.
DISASSEMBLING THE FREEZER
DOORS
• Be sure to remove the Fridge Door before
CAUTION
• Be careful with the wires attached to the bottom
1. With the door open, remove the screw
removing the Freezer Door.
of the Freezer Door while disassembling.
holding the cover (A) of the Adjustable Leg
at the bottom of the door with a Phillips
(+) Screwdriver, and then disassemble the
Connector (B).
3. Pull up the Fixer Lever (E), and then pull it
forward.
E
E
2. Lift up and remove the Mid Hinge Cap (C) on
A
B
the Door Hinge above the Freezer Door.
C
English - 20
DA68-03194H (EN)-06.indd 20 2016. 3. 24. �� 3:21
3. While pushing the door in the direction of the
arrow, lift up the Mid Hinge Shaft (D).
D
4. Being careful that the door does not touch the
Mid Hinge (E), tilt the Door forward a little, and
then lift it up to remove.
1
• Be careful not to damage the wires on
CAUTION
the bottom of the door.
Avoid stepping on them, etc.
2. Insert the Hinge Shaft (C) into the Mid Hinge
Hole (D) and put on the Hinge Cap (E).
• When assembling the Hinge Shaft and
the Hinge Cap, be sure to assemble
them in the correct direction.
C
D
E
SETTING UP
E
2
ASSEMBLING THE
REFRIGERATOR DOORS
• Be sure to re-attach the Freezer Door
CAUTION
• Before re-attaching, make sure that all the wire
How to Re-attach the Freezer Door
1. Insert the door into the lower hinge (A) in the
before re-attaching the Fridge Door.
connectors at the bottom of the Freezer Door
are connected.
direction of (1) and then push the door in the
direction of (2).
Take care not to scratch the door with the MidHinge (B).
B
2
3. With the door open, join the connectors on the
bottom of the door.
- Be careful not to step on or damage the
connectors.
4. Attach the Adjustable Leg Cover using a Phillips
(+) Screwdriver.
A
1
English - 21
DA68-03194H (EN)-06.indd 21 2016. 3. 24. �� 3:21
How to Re-Attach the Fridge Door
1. Attach the detached Fridge Door to the Mid
Hinge.
5. Connect the Water Tube (C). Connect the
two connectors on the left door and the one
connector (E) on the right door.
E
C
E
2. Slide the Fridge Hinge (A) into the fixing slot,
and then press it down so that it is aligned with
the hole in the door.
A
3. Inserting the Fixer Lever (B) in the direction of
the arrow, and then flip it down to assemble.
B
B
4. Assemble the Wire Connector.
6. Attach the front of the Top Cover, and then
press down on its back until it lies flat.
Re-attach the screws.
• Assemble the Fridge and Freezer doors
CAUTION
in the reverse order of disassembly.
• If the Wire Connectors are cross-assembled,
the display will not work properly.
E
Center of the Indicator
Line
English - 22
DA68-03194H (EN)-06.indd 22 2016. 3. 24. �� 3:21
LEVELING THE REFRIGERATOR
AND ADJUSTING HEIGHT AND
GAP OF THE DOORS
How to level the refrigerator
To avoid a hazard due to
instability of the refrigerator,
please place the refrigerator
on a horizontal support and
levelled in accordance with
the following instruction for
installation.
Failing to do so may result in
the refrigerator tipping and a
personal injury.
If the front of the appliance is
slightly higher than the rear,
the door can be opened and
closed more easily.
Setting up the refrigerator on
an uneven surface will cause
the refrigerator to be uneven.
If the Refrigerator is put on a floor that is not level,
it can cause a height dierence between the doors.
• Insert a Flat-Head (-) Screwdriver into the slot
in the Leveling Leg Control Lever and adjust the
level by turning the Control Lever clockwise or
counter-clockwise.
When you rotate the Lever clockwise, you raise
the refrigerator.
When you rotate the Lever counter-clockwise,
you lower the refrigerator.
Flat-blade
screwdriver(-)
• If the Refrigerator is not level back and
front, put a solid panel (such as a plastic
panel, a plastic ruler, etc.) on the floor
where the rear legs will rest, and then fix
it in place with plastic tape.
When you push in the Refrigerator, make
• If you have a wooden floor or similar soft floor,
sure the rear legs rest on the panel.
take care not to damage the floor when pushing
the Refrigerator into place.
Control Lever
SETTING UP
- When install the refrigerator,
the legs should touch the
floor surely.
The legs should be located
on the back of under the
each door.
Insert it with flathead
screwdriver and tighten up to
arrow direction.
English - 23
DA68-03194H (EN)-06.indd 23 2016. 3. 24. �� 3:21
HOW TO ADJUST THE DOOR
HEIGHT
If any one of the doors is lower
than the other:
• Check if the Refrigerator is
level before adjusting the
door.
• Adjust the door height dierence by inserting a
Snap Ring (1) as shown between the door and
the hinge.
You can use the rings on the right side door of
the fresh food compartment and both sides of
the freezer compartment.
(1)
• After checking the height dierence, select one
Snap Ring with a suitable thickness. Insert one
Snap Ring only, Inserting two or more Snap
Rings may cause the Snap Rings to slip out or
make a rubbing noise.
• Lift up the lower door and insert the Snap Ring
into the space between the Door and the Hinge.
Snap Rings included with the refrigerator:
1mm 1.5mm 2mm 2.5mm
HOW TO ADJUST THE DOOR GAP
If the gap between the left and right fridge
compartment doors is not even.
• You can adjust the gap by
turning the bolt at the top
right of the cold storage
compartment door.
• Do not turn the bolt too far.
You can break it.
1. With the doors closed, remove the 3 screws
holding the top cover using a Phillips
screwdriver, and then lift it o together with the
connected cables.
• To avoid injury, insert or remove Snap
CAUTION
• Keep the Snap Rings out of the reach of
• If the Refrigerator is level before you load it with
• If you raise the door too far, it can rub against
DA68-03194H (EN)-06.indd 24 2016. 3. 24. �� 3:21
Rings carefully.
children and make sure that children do not
play with them or put them into their mouths.
• 1mm, 1.5mm, 2mm, and 2.5mm Snap
Rings come with the Refrigerator.
food, the Refrigerator may become unbalanced
due to the weight of the food.
If this occurs, adjust the level again using the
same procedure.
the Top Cover.
English - 24
2. Turn the bolt with a 4mm
hexagonal L-wrench to
adjust the gap.
3. Turn the bolt clockwise to ( ) widen the
gap. Turn the bolt counter clockwise ( ) to
narrow the gap.
INSTALLING THE WATER
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator.
To help promote better health, the water filter
removes unwanted particles from your water.
However, it does not sterilize or destroy
microorganisms.
You may need to purchase a water purifying
system to do that.
The water line also connects to the ice maker.
For the ice maker to operate properly, water
pressure of 138 ~ 862kPa is required.
If the refrigerator is installed in an area with low
water pressure (below 20psi), you can install a
booster pump to compensate for the low pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly filled.
To do this, press the water dispenser lever until the
water runs from the water outlet.
• Water line installation kits are available at
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper
tubing and 6mm (¼”) compression nut.
• The new hose-sets supplied with the appliance
are to be used and that old hose-sets should
not be reused.
Connecting to the water supply line
1. First, shut o the main water
supply.
2. Locate the nearest cold water drinking line and
install the pipe clamp and shut o valve.
Cold water line
Pipe clamp
Shut o valve
3. Connect the water line installation kit to the shut
o valve.
Cold water line
Pipe clamp
Shut o valve
Water line installation
kit
SETTING UP
Connecting the water supply line to the
refrigerator
There are several items that you need to purchase
to complete this connection.
You may find these items sold as a kit at your local
hardware store.
Use Copper Tubing Use Plastic Tubing
• ¼” copper tubing
• ¼” compression nut (1pc)
• Ferrule (2pc)
English - 25
DA68-03194H (EN)-06.indd 25 2016. 3. 24. �� 3:21
• ¼” plastic tubing
Molded end (Bulb)
→
• ¼” compression nut (1pc)
Refrigerator
Plastic Tubing
Compression Nut
(1/4”) (Assembled)
Ferrule
(Not supplied)
Copper tubing
(Not supplied)
Household water supply line
(Assembled)
Compression
Fitting
(Assembled)
Plastic tubing (A)
or
(Not supplied)
Molded end
(Bulb)
Compression
nut (B) (1/4”)
(Not supplied)
1. Connect the household water line to the
assembled compression fitting.
- If you are using copper tubing, slip the
compression nut (B) (not supplied) and ferrule
(not supplied) on the copper tubing (not
supplied) as shown.
- If you are using plastic tubing (A), insert the
molded end (Bulb) of the plastic tubing (A) into
the compression fitting.
5. After you turn on the refrigerator, let the ice
maker make ice for 1 to 2 days.
Over that period of time, throw out the first 1 or
2 buckets of ice the freezer makes to ensure all
impurities have been removed from the water
line.
• Only connect the water line to a drinkable
water source.
• If you have to repair or disassemble the water
line, cut o 1/4“ of the plastic tubing to make
sure you get a snug, leak-free connection.
• You can test the water line quickly using a
paper cup.
Under normal conditions, the water dispenser
can fill a 170cc cup in about 10 seconds.
PRODUCT FEATURES
• TRIPLE COOLING
- Freezer/Fresh food compartment/convertible
compartment are able to maintain optimum
temperature/humidity using by each condenser.
And also smell will not mix.
• FLEX ZONE
- It is able to various storage using by Freezer/
Cooling/cool selection/thin ice options.
• CHILL
- Fixed temperature technology will keep
freshness.
• Do not use without the molded end (Bulb)
CAUTION
of the plastic tubing (A).
2. Tighten the compression nut (B) onto the
compression fitting.
Do not over-tighten the compression nut (B).
3. Turn water on and check for any leakage.
If you find water drops or leakage in the
connection areas, turn o the main water
supply. Check the connections and, if
necessary, tighten.
4. Flush 1 gallon of water through the filter before
drinking or using the water from the refrigerator.
(Flush approximately 6 minutes.)
To flush, press a large glass or cup against the
water dispenser lever.
Fill the glass, empty it into the kitchen sink after
it is filled, and then repeat.
English - 26
DA68-03194H (EN)-06.indd 26 2016. 3. 24. �� 3:21
Operating your Samsung
refrigerator
USING THE CONTROL PANEL
(1)
(2)
(3)
Freezer
(1)
(Hold 3sec for Power Freeze)
Touch this button to set the freezer to your
desired temperature.
You can set the temperature between
-23°C and -15°C.
Touch and hold this button for 3 seconds
to decrease the time needed to freeze
products in the Freezer.
This can be helpful if you need to quickly
freeze easily spoiled items or if the
temperature in the freezer has warmed
dramatically.
(For example, if the door was left open.)
(6)
(4)
(5)
(7)
(8)
Door Alarm
(2)
(Hold 3sec for °C↔°F)
This button serves two purposes:
1. To turn the door open alarm on and o
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left open
for more than two minutes.
The beeping stops when you close the
door. The door alarm function is pre-set to
On in the factory.
You can turn it o by touching and then
releasing this button.
You can turn it back on in the same
fashion.
The icon lights up when the function is on.
When the Door Alarm function is on and
the alarm sound is triggered, the Door
Alarm Icon will blink while the alarm
sounds.
OPERATING
2. Touch and hold this button for
3seconds to switch the temperature
units between °C and °F.”
English - 27
DA68-03194H (EN)-06.indd 27 2016. 3. 24. �� 3:21
Energy Saver
(3)
(Hold 3sec for Control Lock)
Touching this button turns Energy Saver
mode on and o. When you turn Energy
Saver on, the Energy Saver icon lights.
Turn Energy Saver o and the icon goes
o.
The Energy Saver function is set to “ON” in
the factory.
If condensation or water drops appear on
the doors, turn the Energy Saver mode o.
Also, touching this button for 3 seconds
turns on Control Lock which locks the
display panel and dispenser buttons so the
buttons can not be used.
Touch 3 seconds to unlock.
Fridge
(4)
(Hold 3sec for Power Cool)
Touch this button to set the fridge to your
desired temperature.
You can set the temperature between 1°C
and 7°C.
Touch and hold this button for 3 seconds
to decrease the time needed to cool
products in the Fridge.
This can be helpful if you need to
quickly cool easily spoiled items or if the
temperature in the fridge has warmed
dramatically.
(For example, if the door was left open.)
(5) Cool Select+ (Cool Select Room)
The CoolSelect+ button lets you set the
Cool Select Room on the bottom right of
your refrigerator to one of four settings:
Freezer, Soft Freezing, Chill, or Cool.
Press the CoolSelect+ button for three
seconds to activate the Cool Select Room
function, and then select one of the four
settings.
Freezer
Select Freezer to set the same temperature
as the freezer.
• Use this setting to keep frozen food.
Soft Freezing
Select Soft Freezing to set the temperature
to -5°C.
• Use this setting to keep meat and fish
fresh longer than fridge.
Chill
Select Chill to set the temperature to -1°C.
• Use this setting to keep deli like steak,
fish, bacon and cheese.
Cool
Select Cool to set the temperature to 2°C.
• Use this setting to keep drink (juice,
soft drinks and beer), vegetable, fruit,
etc.
English - 28
DA68-03194H (EN)-06.indd 28 2016. 3. 24. �� 3:21
(6) Ice Type
Touch the Ice Type button to change the
ice type.
Each time you touch the Ice Type button,
the cubed and crushed ice modes
alternate and the Cubed or Crushed ice
icon lights up, indicating your selection.
If you don’t need ice, turn the function o
to save on water and energy consumption.
(See Ice Maker O below.)
Lighting
Touch the Cubed button for three seconds
to set the Dispenser LED lamp (under the
display) to continuous mode so that it
stays on continuously.
If you want the Dispenser lamp to come on
only when some one uses the dispenser,
touch this button for 3 seconds again to
turn the continuous mode o.
(7) Ice Maker O (Hold 3sec)
Touch the Ice Maker O button for
3seconds until the Ice Maker O Indicator
( ) illuminates.
(8) Filter
Water filter usage
This icon will light up when you need to
change the filter.
After you use about 300 gallons of water,
the filter indicator lights up. (in about 6
months)
The icon will blink red for several seconds
when you open or close the door.
After you install the new water filter, touch
and hold the Crushed Ice button for
3Seconds to reset the filter.
- If water is not dispensing or dispensing
slowly, you need to replace the water
filter because the water filter is clogged.
- Some areas have large amounts of lime
in their water, which causes the water
filter to clog more quickly.
Exhibition Mode
OPERATING
• In case of Exhibition Mode, It seems
CAUTION
working but doesn’t make cool air.
To cancel this mode, touch the Freezer,
Fridge and Door Alarm buttons at the
same time for 5 seconds until “Dingdong”
sounds.
Or you can cancel the exhibition mode
by turning the power o.
English - 29
DA68-03194H (EN)-06.indd 29 2016. 3. 24. �� 3:21
CHANGING THE WATER FILTER
• To reduce risk of water damage to your
WARNING
property DO NOT use generic brands
of water filters in your SAMSUNG
Refrigerator.
2
3
USE ONLY SAMSUNG BRAND
WATER FILTERS.
SAMSUNG will not be legally
responsible for any damage,
including, but not limited to, property
(Red)
damage caused by water leakage
from the use of a generic water filter.
SAMSUNG Refrigerators are designed to work
ONLY WITH SAMSUNG Water Filter.
The Filter light turns red to let you know when it is
time to change your water filter cartridge.
To give you time to get a new filter, the red light
comes on just before the capacity of the current
filter runs out.
Changing the filter on time provides you with the
freshest, cleanest water from your refrigerator.
1. Shut o the water supply.
Then, turn the water filter (1) about 1/4 turn,
counter-clockwise.
2. Pull the water filter (1) from the case filter (2).
• To change the water filter more easily,
shut o the water supply valve.
• Sometimes, it is hard to disassemble the water
filter because impurities in the water cause it to
stick. If you are having diculties, grip the water
filter firmly and pull it hard.
• When you pull out the water filter, a little water
can leak from the opening. This is normal.
To minimize the water leaks, keep the filter
cartridge horizontal when you pull it.
• To prevent overflow, empty the water filter tray
(3) and dry around the filter case (2).
3. Insert the new filter into the filter case (4).
4
4. Push the filter in, and then turn it clockwise until
it locks.
• If you have trouble inserting the water
filter because of high water pressure,
shut o the water supply valve.
• The locked symbol should be lined up with the
indicator line.
2
5. Touch the “Crushed/Hold 3 sec for Filter Reset”
button (
1
(Filter Reset)
) for about 3 seconds to
reset the water filter. The color of the indicator
changes from red to o.
6. If you turned o the water supply, turn it back
on.
• For a replacement water filter, visit your
local home Improvement center, go to
Samsung Parts.com on line, or contact
your authorized Samsung dealer.
Be sure the replacement water filter has
the SAMSUNG logo on the box and on
the water filter.
English - 30
DA68-03194H (EN)-06.indd 30 2016. 3. 24. �� 3:22
Removing any residual matter inside the
water supply line after installing the water
filter.
1. Turn ON the main water supply and supply
water from water supply line.
2. Run water through the dispenser until the water
runs clear (approx. 6 to 7 minutes).
This will clean the water supply system and
remove air from the lines.
3. Additional flushing may be required in some
households.
4. Open the Refrigerator door and make sure there
are no water leaks coming from the water filter.
• Be sure to flush the dispenser thoroughly,
otherwise water may drip from the
dispenser.
This means that there is still air in the line.
Reverse Osmosis Water Supply
IMPORTANT:
The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet
valve of the refrigerator needs to be between 241
and 827kPa.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 276 to 414kPa.
If the water pressure to the reverse osmosis system
is less than 276 to 414kPa:
• Check to see whether the sediment filter in the
reverse osmosis system is blocked.
Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
• If your refrigerator has a water filter, it may
further reduce the water pressure when used
in conjunction with a reverse osmosis system.
Remove the water filter.
If you have questions about your water pressure,
call a licensed, qualified plumber.
OPERATING
English - 31
DA68-03194H (EN)-06.indd 31 2016. 3. 24. �� 3:22
CONTROLLING THE
TEMPERATURE
Recommended freezer and fridge
compartment temperatures
The recommended temperatures for the Freezer
and fridge Compartments are -19°C and 3°C
(-2°F and 38°F) respectively.
If the temperature of the Freezer and fridge
Compartments are too high or low, adjust the
temperature manually.
CONTROLLING THE FREEZER
TEMPERATURE
Recommend Temp (Freezer) : -19°C (-2°F)
Freezer
Press the Freezer button to set the freezer to
desired temperature from the range between
-15°C and -23°C.
Default set temperature is set on -19°C and each
time you press the Freezer button, temperature will
change in following order and temperature indicator
will display the desired temperature.
• The Freezer or Fridge temp indicator
will blink when the temperature in the
fridge or freezer compartment goes up
dramatically.
(Freezer or Fridge temperature indicator
will stop blinking when temperature in the
Freezer or Fridge becomes normal.
If temperature indicator does not stop
blinking after several hours, please
contact your service center.
Power Freeze
The Power Freeze function substantially speeds up
the freezer compressor, causing the freezer to cool
down rapidly to a temperature you choose.
When you touch and hold the Freezer button
for 3seconds, Power Freezer function will be
activated.
Power Freeze is useful if you need to quick freeze
an item, to make a large quantity of ice, or to cool
the freezer rapidly if it has warmed dramatically (for
example, if the door was left open).
To turn the Power Freeze function o manually,
press the Freezer button, and then re-set the
Freezer temperature.
Power Freeze turns o automatically after 50 hours
to decrease energy consumption.
When you use this function, the energy
consumption of the refrigerator will increase.
If you need to freeze large amounts of food,
activate the Power Freeze function at least
20hours before.
-19°C
-20°C -21°C -22°C -23°C
-18°C -17°C -16°C -15°C
English - 32
DA68-03194H (EN)-06.indd 32 2016. 3. 24. �� 3:22
CONTROLLING THE FRIDGE
TEMPERATURE
Recommend Temp (Fridge) : 3°C (37°F )
Press the Fridge button to set the fridge to desired
temperature from the range between 1°C and
7°C.
Default set temperature is set on 3°C and each
time you press the Fridge button, temperature will
change in following order and temperature indicator
will display the desired temperature.
USING THE ICE AND COLD
WATER DISPENSERS
Push the appropriate ice type button
to select what you want dispensed
Using the ice lever (1)
Push the Ice lever dispenser (1) gently with your
glass. Ice will be released from the dispenser.
You can choose the type of ice by pushing the
cubed or crushed button first.
NO ICE
Select this if you want to turn ice
maker o
OPERATING
3 °C
• The temperature of the Freezer, Fridge
or Cool Select Room may rise when
you open the doors too frequently, or if
a large amount of warm or hot food is
placed inside.
• This may cause the digital display to blink.
Once the Freezer and Fridge temperature return
to their normal set temperatures, the blinking
will stop.
• If the blinking continues, you may need to “reset”
the Refrigerator.
Try unplugging the appliance, wait for around
10 minutes, and then plug the power cord back
in.
• If there is a communication error between the
Display and Main Controller, the Display light
may blink “PC-Er” with Beep Sound.
If the blinking continues for a long period of
time, please contact a Samsung Electronics
Service Center.
2 °C 1 °C 7 °C
4 °C 5 °C 6 °C
Using the Water lever (2)
Push the Water lever dispenser (2) gently with
your glass.
Water will be released from the dispenser.
( 1 )
( 2 )
• If you push the water and Ice lever at
about the same time, the dispenser
operates only the option you actually
selected or pushed first.
• Please wait 1 second before removing
the cup after dispensing water to prevent
spills. Do not pull out the lever dispenser
after dispensing ice or water.
It comes back automatically.
English - 33
DA68-03194H (EN)-06.indd 33 2016. 3. 24. �� 3:22
Using the Ice & Water Dispenser together
To get Ice and water, push the Ice lever (1) first
for ice, then move your glass down and press the
water dispenser lever (2) for water.
• To test the ice maker, press the Test button on
the ice maker.
You will hear the refrigerator chime (ding-dong).
When the chime sounds, release the Test
button.
• The chime sounds automatically again to let you
know the ice maker is working well.
MAINTAINING THE ICE BUCKET
• To clean the ice bin/bucket, wash with a mild
detergent, rinse well, and dry thoroughly.
Do not use harsh or abrasive cleaners or
solvents.
• Ice is made in cubes.
When you select “Crushed”, the ice maker
grinds the ice cubes into crushed ice.
• When you select Cubed Ice after using the
Crushed Ice mode, a small amount of residual
crushed ice might be produced.
• The ice cubes generated by the rapid ice
making process will look white, which indicates
they are generated normally.
• If ice doesn’t come out, pull out the ice bucket
and press the Test button located on the right
side of ice maker.
See the illustration under Making Ice below.
• Do not press the Test button continuously if the
tray is filled with ice or water.
Water may overflow or ice may jam the bucket.
MAKING ICE
• To fill the ice bucket to maximum capacity after
installation, follow these steps:
1. Allow your refrigerator to operate and cool
down for 24 hours (or 1 full day).
- Waiting 24 hours will allow your ice maker to
cool properly.
2. Dispense 4 to 6 ice cubes into a glass.
3. After another 8, and then 16 hours, dispense a
full glass of ice.
Check the water
level
Test button
• If you want to remove the ice cubes
CAUTION
without using the ice bucket, please turn
the ice maker o.
(However, remove the front cover from
the ice maker.)
The ice cubes in the ice maker can spill
out over the drawer.
• Do not put food in the ice bucket.
CAUTION
If you store food in the ice bucket, the
food may get in the way of the ice maker
while opening/closing the door, causing
damage to the ice maker.
• Note that the ice cubes in the ice bucket
CAUTION
may spill out over the drawer when
removing the ice bucket from the drawer.
If this is the case, be sure to clear the ice
cubes that spilled out of the drawer.
• If a power failure occurs, ice cubes
CAUTION
may melt then freeze together when
the power comes back on, causing the
dispenser to be out of order.
To prevent this problem, after a power failure, pull
out the ice bucket and discard the residual ice or
water.
• If you use all the ice at once, you must
repeat Steps 2 and 3 above.
However, only wait 8 hours before
dispensing the first 4 to 6 ice cubes.
This will replenish the ice cubes and
ensure maximum ice production.
English - 34
DA68-03194H (EN)-06.indd 34 2016. 3. 24. �� 3:22
USING THE ICE OFF FUNCTION
When you select the Ice O mode, remove all ice
cubes from the bucket.
If you leave the ice cubes in the bucket, the ice
cubes may clump together, making it dicult to
remove them.
To remove the ice bucket safely and avoid injury,
hold the bottom of the bucket with one hand and
the side of the bucket with the other.
Then, lift up on the ice bucket, and pull it straight
out.
To put the ice bucket back in, push it firmly straight
back.
• If the ice bucket is not pushed firmly into
place, ice in the bucket can melt.
If the bucket does not fit, turn the helix 90 degree
(see the last illustration on the right, below) and try
again.
• The inside of the ice bucket is very cold
CAUTION
• Use only the ice maker provided with the
• To operate the ice maker properly, water
when the refrigerator is operating.
Do not reach deep inside the ice bucket.
refrigerator.
The water supply to this refrigerator must only
be installed/connected by a suitably qualified
person.
Connect to a potable water supply only.
pressure of 138 ~ 862 kPa is required.
GOING ON VACATION...
If you are going on a long vacation or business trip
and won’t use the water or ice dispensers for a
long time:
- Close the water valve.
Otherwise, water leakage may occur.
- Remove all food and ice in the ice bucket.
- Unplug the refrigerator.
- Wipe excess moisture from inside and leave the
doors open.
Otherwise, odor and mold may develop.
ICE MAKER DO’S AND DON’TS
Do not put your fingers, hands or any other
unsuitable objects in the chute or ice-maker
bucket.
- You can hurt yourself or damage the refrigerator.
Never put your finger or any other objects in the
dispenser opening.
- You can injure yourself.
Do not try to disassemble the ice maker.
Do not wash or spray the ice bucket with water
while it is in the refrigerator.
Remove it to clean it.
• When you insert the Ice maker tray, be
CAUTION
Water clouding phenomenon
sure that the tray is well centered at the
entrance.
Otherwise, the tray may be stuck.
• All water provided to the refrigerator flows
through a core alkaline water filter.
In the filtering process, the pressure
of the water that has flowed out of the
filter has increased, and the water has
become saturated with oxygen and
nitrogen.
When this water flows out into the air,
the pressure plummets and the oxygen
and nitrogen get supersaturated, which
results in gas bubbles.
The water may temporarily look misty or
cloudy due to these oxygen bubbles.
After a few seconds, the water will look
clear.
OPERATING
English - 35
DA68-03194H (EN)-06.indd 35 2016. 3. 24. �� 3:22
PARTS AND FEATURES
Use this page to become more familiar with the parts and features of the Refrigerator.
Fridge
Ice-Maker
Fridge Multi-Purpose
EZ Fresh Vegetable &
EZ Freezer Slide-Shelf
Dry Food and Meat
Freezer Door Bins
Guard
Fruit Drawers
Storage Bin
( 1 ) ( 1 )
Freezer
Cool select room
Foldable-Shelf
Fixed-Shelf
Quick Space -Shelf
Egg tray
Water filter
Cool Select Room
The door guards in the freezer of this model are the two star sections except the top guard, so
the temperature in two star sections are slightly higher than other freezer compartment.
(1) is two star section.
When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid
scratching the other door. If the Vertical Hinged Section is reversed, put it back into the correct
position, and then close the door.
Moisture may appear at times on the Vertical Hinged Section.
The door handle may become loose over time.
If this happens, tighten the bolts found on the inside of the door.
If you close one door with too much force, the other door may open.
When the door opens, the interlock switch automatically turns o the auger motor in the ice
maker for safety reasons.
If the interior or exterior LED lamp has gone out, please contact Samsung service.
English - 36
DA68-03194H (EN)-06.indd 36 2016. 3. 24. �� 3:22
ADDITIONAL PART - ASSY SHELF
FRE
To get more space, you can remove each Middle
drawer of freezer and Cool Select Room.
And then, locate the ‘ASSY SHELF FRE’ between
middle and bottom drawers of the freezer and Cool
Select Room, since it does not aect thermal and
mechanical characteristics.
ASSY SHELF FRE
ASSY SHELF FRE
EZ Freezer
Slide-Shelf
Middle drawer
Location of ASSY
SHELF FRE
• The ASSY SHELF FRE shall be used
CAUTION
only to the designated location with the
Middle drawer removed.
• Do not place and use the ASSY SHELF FRE on
the EZ Freezer Slide-Shelf.
• Able to prevent damage when not in use,
please store the ASSY SHELF FRE in a secure
place.
• Do not insert the shelf upside-down, or in the
reverse direction.
OPERATING
1. Remove the attached Tape on the shelf.
2. Take out the middle drawer to assemble the
ASSY SHELF FRE.
3. Insert the ASSY SHELF FRE with the “REAR”
mark side up.
If the “REAR” mark is unable to identify, insert
the protruding part of the ASSY SHELF FRE at
first as shown in figure.
(1)
English - 37
DA68-03194H (EN)-06.indd 37 2016. 3. 24. �� 3:22
REMOVING THE REFRIGERATOR
ACCESSORIES
1. Door Bins or Guards Compartment
• To remove - Simply lift the bin up and pull
straight out.
• To relocate - Slide it in above the desired
location and push down until it stops.
• Injuries can occur if the door bins are not
CAUTION
firmly attached to the doors.
Do not allow children to play with longer.
Sharp corners of the bins may cause
injury.
2. Tempered Glass shelves
• To remove - Tilt up the front of the shelf in the
direction shown (1) and lift it up vertically (2).
Pull the shelf out.
• To relocate - Tilt the front of the shelf up and
guide the shelf hooks into the slots at a desired
height.
Then, lower the front of the shelf so that the
hooks can drop into the slots.
• The Tempered Glass shelves are heavy.
CAUTION
Use special care when removing them.
• Do not adjust a bin full of food.
Remove the food first.
• Dust removal method - Remove the guard and
wash in water.
• If it is stained with oil after use, wash in
water right away.
1
2
3. Vegetable & Fruit Drawers (EZ Fresh Zone)
• Holding the drawer with one hand, lift it up a
little bit while pulling it forward, and then pull it
out of the refrigerator.
• Remove the door bins before removing
the drawer to prevent damage to the
door bins.
English - 38
DA68-03194H (EN)-06.indd 38 2016. 3. 24. �� 3:22
CLEANING THE REFRIGERATOR
• Do not use benzene, thinner, Clorox, or
WARNING
• Do not spray the refrigerator with water while it
car detergent to clean the refrigerator.
They can damage the surface of the
appliance and may cause a fire.
is plugged in, This can cause an electric shock.
• To clean the refrigerator, follow these steps:
1. Unplug the power code of the refrigerator.
2. Slightly dampen a soft lint-free cloth or paper
towel with water.
Do not use any kind of detergent to clean
the refrigerator because that can discolor
or damage the refrigerator.
3. Wipe the inside and outside of refrigerator until
it is clean and dry.
4. Plug the power code of the refrigerator back in.
CHANGING THE INTERIOR
LIGHTS
Freezer / Fridge LED Lamp
• If the LED Lamp Cover is stained with foreign
substances, the LED lamp may not look bright.
Wipe the surface cover with clean dry cloth to
return the light to full brighteness.
• Do not disassemble or replace the LED
CAUTION
type lighting yourself.
To replace the LED lights, contact
a Samsung service center or your
authorized Samsung dealer.
OPERATING
If you attempt to replace the LED lamps
yourself, you risk subjecting yourself to an
electric shock or serious personal injury.
English - 39
DA68-03194H (EN)-06.indd 39 2016. 3. 24. �� 3:22
Troubleshooting
PROBLEM SOLUTION
The refrigerator
does not work at
all or it does not
chill suciently.
The food in the
fridge is frozen.
You hear unusual
noise or sounds.
• Check if the power plug is properly connected.
• Check if the set temperature on the digital display is warmer than the
freezer or fridge inner temperature.
If it is, set the freezer or fridge to a colder temperature.
• Is the refrigerator in direct sunlight or located near a heat source?
If so, it may not be able to cool suciently.
Install it in a location that is out of direct sunlight and not near a heat
source.
• Is the back of the refrigerator too close to the wall, preventing proper
ventilation? If so, it may not be able to cool suciently.
Keep it an appropriate distance from the wall.
• Is there too much food inside so that the food is blocking the outlet vent?
To keep the refrigerator at a suitable temperature, do not fill the refrigerator
with too much food.
• Check if the set temperature on the digital display is too low.
If so, raise the set temperature inside the refrigerator.
• Is the temperature in the room too low? Set the refrigerator warmer.
• Did you store food with a high moisture content in the coldest part of the
refrigerator or near the cooling outlet vent?
Try moving those items to the other shelves in the fridge instead of
keeping them in the colder areas or bins.
• Check if the refrigerator is level and stable.
• Is the back of the refrigerator too close to the wall, preventing proper
ventilation?
• Was anything dropped behind or under the refrigerator?
• If you hear a “ticking” sound from inside the refrigerator, this is normal.
It occurs because various parts contract or expand in response to
temperature changes in the refrigerator interior.
• If it sounds as if something is hitting something else inside the refrigerator,
this is normal.
The sound is caused by the compressor operating at high capacity.
The cabinet-door
sealing area of the
appliance is hot
and condensation
is occurring.
The Ice Maker is
not producing ice.
DA68-03194H (EN)-06.indd 40 2016. 3. 24. �� 3:22
• Some heat is normal as anti-condensators are installed in the vertical
hinged section of the refrigerator to prevent condensation.
• Is the refrigerator door ajar?
Condensation can occur when you leave the door open for a long time.
• It may take longer to make ice if it is not suciently cool, such as when
first installed.
• Is the water line connected and the shut-o valve opened?
• Did you manually stop the ice making function?
• Check if the filter is properly installed.
If it is not properly installed, the ice making function may not work.
English - 40
PROBLEM SOLUTION
You can hear water
bubbling in the
refrigerator.
There is a bad
smell in the
refrigerator.
Frost forms on the
walls of the freezer.
The water
dispenser is not
functioning.
The auto close
system does not
work with the
freezer door.
Condensation or
water drops forms
on vertical mullion
and surroundings,
etc.
• This is normal.
The bubbling comes from refrigerant circulating through the refrigerator.
• Check for spoiled food.
• Foods with strong odors (for example, fish) should be tightly covered.
• Clean out your freezer periodically and throw away any spoiled or
suspicious food.
• Is the air vent blocked?
Remove any obstructions so air can circulate freely.
• Allow sucient space between the stored food for ecient air circulation.
• Is the freezer drawer closed properly?
• Is the water line connected and the shut-o valve opened?
• Has the water supply line tubing been crushed or kinked?
• Make sure the tubing is free and clear of any obstruction.
• Is the water tank frozen because the fridge temperature is too low?
Try selecting a warmer setting on the Digital display.
• Check if the filter is properly installed.
If it is not properly installed, the water dispenser may not work.
• Is there an imbalance between the right and left parts of the door?
• Open and close the door smoothly 1~2 times.
After you do this, the auto close system usually works properly again.
• Try opening the door smoothly to avoid unbalancing the right part and the
left part of the door.
• Condensation or water drops may form if the humidity is too high while the
refrigerator is operating.
• If condensation or water drops appears on vertical mullion and
surroundings, etc., turn the Energy Saving mode o after removing the
condensation.
TROUBLESHOOTING
English - 41
DA68-03194H (EN)-06.indd 41 2016. 3. 24. �� 3:22
Memo
DA68-03194H (EN)-06.indd 42 2016. 3. 24. �� 3:22
Memo
DA68-03194H (EN)-06.indd 43 2016. 3. 24. �� 3:22
Ambient Room Temperature Limits
This refrigerator is designed to operate in ambient temperatures specified by its temperature class marked
on the rating plate.
Class Symbol
IEC 62552 (ISO 15502) ISO 8561
Extended Temperate SN +10 to +32 +10 to +32
Temperate N +16 to +32 +16 to +32
Subtropical ST +16 to +38 +18 to +38
Tropical T +16 to +43 +18 to +43
Ambient Temperature range (°C)
Internal temperatures may be aected by such factors as the location of the fridge/freezer,
ambient temperature and the frequency with which you open the door.
Adjust the temperature as required to compensate for these factors.
Correct Disposal of This Product
English
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types
of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
(Waste Electrical & Electronic Equipment)
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
COUNTRY CALL Web site
AUSTRALIA 1300 362 603 www.samsung.com/au/support
COLOMBIA
EIRE 0818 717100 www.samsung.com/ie/support
HONG KONG 3698 4698
INDIA
MALAYSIA
NEW ZEALAND 0800 726 786 www.samsung.com/nz/support
PANAMA 800-0101
PHILIPPINES
SINGAPORE 1800-SAMSUNG (726-7864) www.samsung.com/sg/support
SOUTH AFRICA 0860 SAMSUNG (726 7864) www.samsung.com/support
UK 0330 SAMSUNG (7267864) www.samsung.com/uk/support
Gratis desde cualquier parte del país 01 8000 112
1-800-8-726-7864 [ Globe Landline and Mobile ]
Bogotá 600 12 72
112 ó desde su celular #SAM(726)
1800 3000 8282 - Toll Free
1800 266 8282 - Toll Free
1800-88-9999
603-77137477 (Overseas contact)
1-800-10-726-7864 [ PLDT Toll Free ]
02-422-2111 [ Standard Landline ]
www.samsung.com/co/support
www.samsung.com/hk/support (Chinese)
www.samsung.com/hk_en/support (English)
www.samsung.com/in/support
www.samsung.com/my/support
www.samsung.com/latin/support (Spanish)
www.samsung.com/latin_en/support (English)
www.samsung.com/ph/support
DA68-03194H-06
DA68-03194H (EN)-06.indd 44 2016. 3. 24. �� 3:22
Loading...