Page 1
POWERbot
user manual
SR2AK9000UG Series
Before operating this unit, please read the instructions carefully.
For indoor use only.
imagine the possibilities
Thank you for purchasing a Samsung product.
English
Page 2
Contents
Safety information
03
Installation
10
Accessories
Charging
12
Automatic charging / Recharging / Low
battery
Using POWERbot
14
Selecting cleaning modes / Using Energysaving mode
Using the remote control
17
Name of each part
18
Top / Bottom / Display panel
Cleaning and maintaining
19
Cleaning the dustbin / Cleaning the sensors and
the camera / Cleaning the Pet brush / Cleaning
the Driving wheel
Notes and cautions
21
Charging / In use / Cleaning and maintenance /
About battery
23
24
25
26
ENGLISH-02
Information codes
Troubleshooting
Open Source Announcement
Specifications
Page 3
Safety information
SAFETY INFORMATION
• Before operating the appliance, please read this manual thoroughly and retain it
WARNING
WARNING
CAUTION/WARNING SYMBOLS USED
for your reference.
• Because these following operating instructions cover various models, the
characteristics of your vacuum cleaner may differ slightly from those described in
this manual.
WARNING
CAUTION
Indicates that a danger of death or serious injury exists.
Indicates that a risk of personal injury or material damage exists.
OTHER SYMBOLS USED
NOTE
Indicates that the following text contains additional imprtant information.
State of California Proposition 65 Warning (US only)
This product contains chemicals known to the State of California to cause
WARNING
cancer and birth defects or other reproductive harm.
L i - i o n
For battery recycling go to call2recycle.org;
or call 1-800-822-8837
ENGLISH-03
Page 4
Safety information
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the
following:
READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.
Unplug from outlet when not in use and before conducting maintenance.
WARNING: to reduce the risk of fire, electric shock, or injury:
GENERAL
•Use only as described in this manual.
•Do not operate POWERbot or the adapter / docking station if it has been damaged in
any way.
•If the vacuum cleaner is not working as it should, has been dropped, damaged, left
outdoors, or dropped in water, return it to a customer care center.
•Do not handle the adapter / docking station or POWERbot with wet hands.
•Use only on dry, indoor surfaces.
•This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
•Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
Adapter / Docking station
•Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
•Do not use outdoors or on wet surfaces.
•Unplug the adapter / docking station from the outlet when not in use and before
servicing.
•Use only the adapter / docking station supplied by the manufacturer to recharge.
•Do not use with a damaged cord or plug or a loose power outlet.
•Do not pull or carry by the cord, use the cord as a handle, close the door on the cord,
or pull the cord around sharp edges or corners. Keep the cord away from heated
surfaces.
•Do not use extension cords or outlets with inadequate current carrying capacity.
•Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
•Do not mutilate or incinerate batteries as they will explode at high temperatures.
•Do not attempt to open the adapter / docking station. Repairs should only be carried
out by a qualified customer care center.
ENGLISH-04
Page 5
•Do not expose the adapter / docking station to high temperatures or allow moisture or
humidity of any kind to come into contact with the adapter / docking station.
POWERbot
•Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.
•Do not use without a filter in place. When servicing the unit, never put fingers or other
objects into the fan chamber in case the unit accidentally turns on.
•Do not put any objects into openings. Do not use with any openings blocked; keep
openings free of dust, lint, hair, and anything that may reduce air flow.
•Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
•Do not pick up anything that is burning or smoke, such as cigarettes, matches, or hot
ashes.
•Do not use to pick up flammable or combustible liquids such as gasoline, nor use on
areas where they may be present.
•Locations with candles or desk lamps on the floor.
•Locations with unattended fires (fire or embers).
•Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.
•Do not use POWERbot in an enclosed space filled with vapours given off by oil based
paint, paint thinner, moth proofing substances, flammable dust, or other explosive or
toxic vapours.
•Leaks from battery cells can occur under extreme usage or temperature conditions.
If the liquid gets on skin, wash quickly with water. If the liquid gets into the eyes,
flush them immediately with clean water for a minimum of 10 minutes. Seek medical
attention.
SAVE THESE INSTRUCTIONS
POLARIZED PLUG INSTRUCTIONS
•To reduce the risk of electric shock, this appliance has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not modify the plug in any way.
ENGLISH-05
Page 6
Safety information
REGULATORY NOTICE
1. FCC Notice
CAUTION
FCC CAUTION:
•Any changes or modifi cations not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
•This device complies with Part 15 of FCC Rules. Operation is Subject to following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that
cause undesired operation.
•For product available in the USA/Canada market, only channel 1 ~ 11 can be operated.
Selection of other channels is not possible.
FCC STATEMENT:
•This equipment has been tested and found to comply within the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
•This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver
– Connect the equipment into an outlet on a diff erent circuit from that to which the
receiver is connected
– Consult the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
•This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20cm between the radiator and your body. This device and its antenna(s) must not
be co-located or operation in conjunction with any other antenna or transmitter.
ENGLISH-06
Page 7
2. IC Notice
•The term “IC” before the radio certifi cation number only signifi es that Industry Canada
technical specifi cations were met. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
•This Class B digital apparatus complies with Canadian ICES-003.
•Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
•For product available in the USA/Canada market, only channel 1 ~ 11 can be operated.
Selection of other channels is not possible.
IC RADIATION EXPOSURE STATEMENT:
•This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This device and its
antenna(s) must not be co-located or operation in conjunction with any other antenna or
transmitter.
Open Source License Notice
•This device uses open source software. Open Source Licenses are available on the
product menu.
•Tap “Settings > Network > Software Update > Legal Information” on the device for more
details.
ENGLISH-07
Page 8
Safety information
WARNING
f Please prevent any risk of electric shock or
fire.
– Do not damage the power cord.
– Do not pull the power cord too hard or touch
the power plug with wet hands.
– Do not use a power source other than 100-
240 V~ and also do not use a multi outlet to
supply power to number of devices at the same
time. (Do not leave the cord carelessly on the
floor.)
– Do not use a damaged power plug, power cord
or loose power outlet.
f Clean dust or any foreign matters on the pin
and contact part of the power plug.
– There is a risk of electric shock or malfunction.
WARNING
f Do not use POWERbot near combustible
materials.
– Place near candle, desktop lamps, fireplace or
near combustible materials such as gasoline,
alcohol, thinners etc.
f The POWERbot is intended for household
use therefore do not use it in an attic,
basement, storage, industrial building, out of
indoor space, places with moisture (such as
bathroom, laundry), on the table or shelves.
– The POWERbot can be damaged or
malfunction.
f Be sure POWERbot does not pass through or
touch any kind of liquids.
– The POWERbot can be severely damaged and
it may contaminate other areas if the wheels
pass through liquid.
f Do not spill any liquids on the docking station.
– There is a risk of fire or electric shock.
Power related
Before use
f Do not use the docking station for anything
other than its intended purpose.
– There is a risk of fire or severe damage to the
docking station.
f Always keep the cliff sensor clean for your
safety.
WARNING
f If any abnormal sounds, smells or smoke
come from POWERbot, immediately shut
off the emergency switch at the bottom of
POWERbot and contact a service center.
WARNING
In use
Cleaning and
maintenance
f When power cord is damaged, contact a
service center to get it replaced by a certified
repairman.
– There is a risk of fire or electric shock.
f Please check with a Samsung Electronics
service center when exchanging batteries.
– Using batteries from other products can cause
malfunction.
ENGLISH-08
Page 9
CAUTION
Before use
CAUTION
In use
f Insert the dustbin before using POWERbot.
f Be careful with the followings for proper
automatic recharging.
– Always turn on the power of the docking
station.
– Install the docking station where POWERbot
can easily find.
– Do not leave any object in front of the docking
station.
f When installing the docking station, do not
leave the cord carelessly on the floor since
POWERbot may get tangled by it.
f Do not use POWERbot on black colored
floors.
– The POWERbot may not be able to operate
normally.
f Do not pick up POWERbot by the dustbin
holder.
f Do not place any objects within 2 ft (0.5 m)
to both sides and 4 ft (1 m) to the front of the
docking station.
f Make sure the docking station's charging
contact is not damaged or have any foreign
matters on it.
f Do not install the docking station in an area
with a dark floor.
– If the floor around the docking station is dark,
recharging is hindered.
f Move any obstacles that may disturb
POWERbot's movement (such as children's
indoor swing or slides) before cleaning.
f Using POWERbot on thick carpet may
damage both POWERbot and the carpet.
– The POWERbot cannot pass over carpet that is
thicker than 0.4 in (1 cm).
f Do not use POWERbot on tables or other
high surfaces.
– There is a risk of damage if it falls.
f The POWERbot may bump into chair, desk
legs therefore move them away for faster and
efficient cleaning.
f When POWERbot is operating, do not lift it up
or carry it to another area.
f Do not hold by driving wheels of POWERbot
when carrying it to another area.
f Do not put any objects on top of POWERbot
since it may cause malfunction.
f Remove any large papers or plastic bags
immediately when using POWERbot since
they may block the intake.
f Do not aim the red pointer directly at people
or animals.
CAUTION
Cleaning and
maintenance
f Prevent any damage to POWERbot by
complying with the following.
– Do not clean POWERbot by spraying water
directly onto it or use benzene, thinner, acetone
or alcohol to clean it.
f Do not disassemble or repair POWERbot.
This should only be done by a certified
repairman.
f Always keep the obstacle sensor and cliff
sensor clean.
– If foreign matter accumulates, sensors may
malfunction.
ENGLISH-09
Page 10
Installation
The docking station must be plugged in and turned on at all times.
Install the docking station in a place
without obstacles and danger of
falling.
About 4 ft (1 m)
About 2 ft
(0.5 m)
DC-IN
About
2 ft (0.5 m)
DC-IN
Connect the
adapter jack
1
to the docking
station
Connect the
power cord to
2
the adapter
When using the adapter,
the side with the sticker
attached must face down.
ENGLISH-10
Connect the
power plug to
3
the outlet
Page 11
Accessories
Remote control Batteries (AAA type) User manual
Docking station Power cord Adapter
Note
f Install the docking station in a place where the floor and wall are level.
f It is best to install the docking station along the grain of wooden floors.
f If the emergency switch is off, the POWERbot will not charge even if it is docked on the docking
station.
f Always turn on the power of the docking station.
– If power is not supplied to the docking station, the POWERbot cannot find it and cannot automatically
recharge.
– If the POWERbot is left detached from the docking station, the battery will drain naturally.
f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is turned
off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn off the sleep
mode.
ENGLISH-11
Page 12
Charging
It takes approximately 240 minutes to
completely charge the POWERbot when
charging it for the first time after purchase.
Once charged, the POWERbot can be used
for approximately 60 minutes.
WARNING
• Rated input voltage of this product
is 100-240 V~.
Turn on the
emergency switch
1
on the bottom
You must turn on the
emergency switch to turn on
the POWERbot.
Manually charge
the POWERbot by
2
placing it on the
docking station
Make sure the charging pins
on the POWERbot and the
docking station are aligned.
ENGLISH-12
Check the
charging status
3
“ ” appear
in the sequence to show
charging progress. All the 6
icons appear when charging
is complete.
Page 13
Automatic charging
When the battery indicator blinks
during cleaning, the POWERbot
will return to the docking station to
charge itself automatically.
Recharging
You can command the POWERbot
to recharge at the docking station
while it is in cleaning.
Low battery
Manually charge the POWERbot by
placing it on the docking station.
Steps to take if recharging not occuring:
Check the installation status of the
docking station when:
fthe docking station is located in a place where the
POWERbot cannot easily access it.
fthe distance between the docking station and
POWERbot is over 16.5 ft (5 m).
– It may take a long time for POWERbot to
return to the docking station for recharging
ENGLISH-13
Manually charge the POWERbot when:
fthe docking station is located in a corner
fthe battery is fully exhausted
fthe POWERbot is immobilized by an obstacle
(furniture etc.)
fthe POWERbot can't climb a threshold near the
docking station (The maximum height of a threshold
the POWERbot can climb is about 0.6 inches
(1.5 cm).)
fthe battery indicator blinks
fthe POWERbot is set to the Spot clean or Manual
clean mode
Page 14
Using POWERbot
You must turn on the emergency switch on the bottom of the unit before using POWERbot.
Turning the power on/off
Press the button for more than
3 seconds
• When POWERbot is not used for
WARNING
30 minutes, power will turn off
automatically.
Starting Auto clean mode
Press and release this button. Cleans all set places
until the battery is depleted.
Stop cleaning: Press and release the button
Starting Spot clean mode
Press and release this button. The POWERbot
cleans a localized area intensely.
Recharging
fRecharging
You can command POWERbot to recharge at the
docking station automatically while it is cleaning
by pressing this button.
ENGLISH-14
Page 15
Selecting cleaning modes
Cleaning mode How to select Displayed icon
Auto clean
Spot clean
The movement and direction of the
Manual clean
When the POWERbot is being charged, you can select the Auto clean mode
only.
If the POWERbot fails to return to the charger, it will be turned into the sleep
mode. Then the display panel of the main body will be turned off. Press [Start/
Stop] or [Power] button to cancel the sleep mode.
Charging and cleaning times may differ according to conditions of use.
POWERbot is controlled by the remote
control.
<Displayed icons in the sleep
mode>
Cleaning method for each modes
About 59 inches (1.5 m)
About 59 inches (1.5 m)
Auto clean
Cleans all set places until the
battery is depleted.
Spot clean
Cleans a localized area intensely.
It can be used to clean bread or
cookie crumbs.
ENGLISH-15
Manual clean
You can control the POWERbot
with the remote control and direct it
to clean a desired spot.
Page 16
Using POWERbot
Using Energy-saving mode
You may select the Energy-saving mode to save energy during battery charging. Energy-saving mode turns off
all functions except battery charging. It reduces the power consumption while you are away from home for an
extended period of time.
How to select or cancel Displayed icon
Press for 5 sec.
When the POWERbot is charging in Energy-saving mode, recharging icon (
icons ( ) blink in order.
About 3 seconds later, the previous
indicator will appear.
) is turned on and the other
Note
f If you select the Auto/Max/Manual clean mode or press Point cleaning button, the Energy-saving
mode will be cancelled.
f During the Energy-saving mode, setting the schedule will cancel the Energy-saving mode.
– If you select the Energy-saving mode after setting the schedule, the schedule will not be cancelled.
f If the power of the docking station is off, the Energy-saving mode will be cancelled.
ENGLISH-16
Page 17
Using the remote control
1 Power/Recharging
1
2
1
5
4
3
Inserting batteries
Open the battery cover by lifting
it up while pressing the locking
tab, and then insert the batteries
as shown in the illustration. Then,
close the cover until it clicks into
place.
Power
Recharging
Start/Stop
Turn POWERbot's power on/off
Select to recharge POWERbot at the
docking station while it is cleaning.
Select to start or stop cleaning
2 Cleaning modes
Auto clean
Spot clean
Cleans all set places until the battery
is depleted.
Select to clean a localized area
intensely
3 Suction modes
Normal mode
Turbo mode
Select to clean with normal suction
power
Select to clean with turbo suction
power
4 Additional functions
Each time you press this button,
Sound
Sound Effects Mute is selected in
this sequence.
5 Direction control
Forword
movement
Left turn
Right turn
Moving backward is not available
ENGLISH-17
Select to move forward
Select to turn left
Select to turn right
Page 18
Name of each part
1
2
3
3
5
6
7
Top
1. Display panel
2. Dustbin holder
3. Remote control signal receiver
4. Obstacle sensor
5. Dustbin
6. Camera
7. Dustbin handle
4
1
2
3
4
5
3
8. Bumper sensor
8
4
Bottom
1. Charge pins
2. Pet brush
7
3. Pet brush cover
4. Cliff sensor
4
5. Roller
8
6. Battery cover
7. Pet brush cover button
6
5
8. Driving wheel
9
9. Emergency switch
10
Display panel
1
2
8 94 765
ENGLISH-18
12
11
3
1. Mute
2. Information indicator
3. Battery indicator
4. Auto clean
5. Spot clean
6. Manual clean
7. Normal mode
8. Turbo mode
9. Recharging
10. Spot cleaning button
11. Start/Stop button
12. Recharging button
Page 19
Cleaning and maintaining
You must turn off the emergency switch before cleaning POWERbot.
Cleaning the dustbin
Remove the dustbin
1
Detach the cyclone unit
4
from the dustbin cover,
and then wash the
dustbin and the filter
Remove the dustbin
2
cover
Reassemble the
5
dustbin
Cleaning the sensors and the camera
Remove dust in the
3
dustbin and cyclone
unit
"Click"
Reinsert the dustbin
6
into the main body until
it clicks
Lightly wipe with soft cloth. Do not use water or cleaning solutions.
Camera
Front sensor
window
ENGLISH-19
Cliff sensors
Rear sensor
window
Page 20
ON
OFF
Cleaning and maintaining
Cleaning the Pet brush
Remove the Pet brush
1
cover
OFF
ON
Reassemble the Pet
4
brush
Remove the Pet brush
2
Reassemble the Pet
5
brush cover
Cleaning the Driving wheel
Clean the Pet brush
3
Put a soft cloth on the floor and place
1
POWERbot upside-down on the cloth.
ENGLISH-20
Use a blunt rod or tweezers to remove foreign
2
matter.
Page 21
Notes and cautions
Charging
Note
f If the battery overheats during charging, it
may take longer to charge.
f When automatic charging is not working, do
the following:
– Turn the emergency switch (on the bottom of
POWERbot) off and on again.
– Unplug the docking station's power plug and
then plug it back on.
– Unplug the docking station, and then check
whether there is any foreign matter on the
charge pins and clean POWERbot and the
charge pins of the docking station with a dry
cloth or rag.
– Check for any obstacles such as reflective
objects, chairs, etc. near the docking station.
f If POWERbot is left detached from the
docking station, the battery will drain naturally.
– Try to keep POWERbot being charged on
the docking station. (However, turn off the
emergency switch and leave the docking
station unplugged when planning to leave the
house for long periods of time by going on a
business trip or vacation, etc.)
In use
Note
f The POWERbot may get caught on
thresholds, etc. during cleaning.
– To restart operation, shut off the emergency
switch, move the POWERbot to an area where
it can move easily, and then turn on the power
again.
f The POWERbot cannot completely clean
areas it cannot enter, such as corners,
between the wall and sofa, etc.
– Please use another cleaning tool to clean them
regularly.
f The POWERbot cannot vacuum clumps of
dirt, so some may remain on the floor after
cleaning.
– Please use another cleaning tool to clean them
regularly.
f If the battery becomes low during Auto clean
mode, POWERbot will recharge and finish
cleaning the remaining area after recharging.
(Repeat cleaning frequency: 1 time)
f You cannot select and have the POWERbot
execute Spot/Manual clean mode while it is
charging.
f Do not unnecessarily move the POWERbot or
press buttons while it is in Auto clean mode. It
assumes that cleaning is complete and starts
cleaning again from the beginning.
f Close doors before cleaning with the
POWERbot. The POWERbot can enter
rooms through thresholds even though the
thresholds are below 1.9 in (5 cm).
f Try not to use the POWERbot at areas near
slides, indoor swing, pots, fireplaces, or
places with flame or moisture.
f Do not lie down around the POWERBOT that
is running.
ENGLISH-21
– If not, it may cause the loss of property.
– Your hair may be caught in the Pet brush,
resulting in physical injury.
Page 22
Notes and cautions
Cleaning and maintenance
Note
f If you washed the dustbin and filter with water
– Dustbin: Completely wipe out the water.
– Filter: Completely dry it in the shade before
using.
f Purchase a filter at authorized Samsung
service centers if you need more filters.
Caution
f Watch your fingers when attaching or
detaching the filter, since they may get stuck
in the dustbin's intake.
f To avoid blockages by foreign matter, do not
let the POWERbot vacuum up toothpicks,
cotton swabs etc.
f If it is difficult to remove foreign matter
from the Pet brush, contact an authorized
Samsung service center.
f Since the Pet brush removes dirt from the
floor during cleaning, foreign matter such as
thread, long hair, etc. may get caught in it. For
the best cleaning results, check and clean it
regularly.
About the battery
Note
f Purchase batteries at authorized Samsung
service centers and check for the genuine
part symbol ( ) and model name
before purchasing.
f This battery is exclusively for the Samsung
Electronics POWERbot. Do not use it for any
other product.
f Do not disassemble or modify the battery.
f Do not throw the battery out in fire or heat it.
f Do not connect any metallic object to the
charging contacts (+, -).
f Store the battery indoors (at 32 °F~104 °F).
f If the battery malfunctions, do not
disassemble it yourself. Contact your nearest
Samsung service center.
f Battery charging time and usage time may
decrease the more the battery is used. If the
battery’s lifespan has been exceeded and it
no longer chargers properly, have it replaced
at a Samsung service center.
f The battery warranty period is 6 months from
the date of purchase.
ENGLISH-22
Page 23
Information codes
The information
1
codes below
appear on the
display panel
If a code appears,
2
turn off the
emergency
switch and check
the instructions
below and take
appropriate action
Information codes Checklist
The POWERbot is caught, stuck, trapped or lifted while
moving around.
fTurn off the emergency switch and move the POWERbot to another
area.
Foreign matter caught in the Power brush.
fTurn off the emergency switch and remove the foreign matter from the
Power brush.
Foreign matter caught in the left Driving wheel.
fTurn off the emergency switch and remove the foreign matter from the
Driving wheel.
The information
3
code will disappear
when you turn on
the emergency
switch
Foreign matter caught in the right Driving wheel.
fTurn off the emergency switch and remove the foreign matter from the
Driving wheel.
Bumper sensor needs to be checked.
fTurn off the emergency switch and turn it back on.
fContact a service center if information code does not disappear.
Foreign matter accumulated on the obstacle sensor.
fTurn off the emergency switch and clean the front and rear sensor
with a soft cloth.
Foreign matter accumulated on the cliff sensor.
fTurn off the emergency switch and clean the cliff sensor with a soft
cloth.
ENGLISH-23
Page 24
Troubleshooting
Symptom Checklist
fCheck if the emergency switch is on.
The POWERbot is not
working at all.
fCheck if all the icons are displayed on the display panel.
fCheck if the POWERbot's battery is depleted.
fReplace the batteries (AAA type) if the remote controller is not working.
The POWERbot
has stopped during
cleaning.
Suction power is weak.
The POWERbot cannot
find the docking
station.
The POWERbot
suddenly cleans
diagonally.
fWhen POWERbot is immobilized by an obstacle such as a cord, threshold etc,
pick it up and move it away from the obstacle.
– If any fabric or string is caught in a drive wheel, turn off the emergency
switch and remove the fabric or string before using it again.
fWhen there's too much dust in the dustbin, suction power may get weakened.
Turn off the emergency switch and empty the dustbin.
fIf the intake (on bottom of POWERbot) is blocked by foreign matter, turn off the
emergency switch and remove foreign matter from the intake.
fWhen noise suddenly increase, turn off the emergency switch and empty the
dustbin.
fIf the dustbin is assembled incorrectly, suction power may get weakened. Turn
off the emergency switch and refer to page 17 for reassembling.
fCheck if there's a power failure or whether the power plug is unplugged.
fRemove any obstacles around the docking station that may prevent
POWERbot from returning to the docking station.
fWhen there's foreign matter on the charge pins, charging can be affected.
Clean the foreign matter off the pins.
fCheck if the docking station is installed along the grain of wooden floors or
tiles.
fThe POWERbot may clean in a diagonal direction if it is moving to another area
using the shortest route. It may also move at a diagonal if it made contact with
an obstacles at that angle, if it was charged at the charger at an angle, or if the
grain of the wooden/tile floor skewed is in that direction.
POWERbot does not
clean a certain area.
fCheck if the charger is installed near a narrow passage or door, and reinstall it
in the other areas.
– If the charger is installed near a narrow passage or door, the
POWERbot cannot pass through the passage or threshold.
ENGLISH-24
Page 25
Open Source Announcement
The software included in this product contains open source software. You may obtain the complete
corresponding source code for a period of three years after the last shipment of this product by sending an email
to mailto:oss.request@samsung.com.
It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM;
a minimal charge will be required.
The following URL http://opensource.samsung.com/opensource/VR9000H/seq/0 leads to the download page
of the source code and open source license information as related to this product. This offer is valid to anyone in
receipt of this information.
ENGLISH-25
Page 26
Specifications
Classification Item Detail information
Size
Mechanical
specifications
(POWERbot)
Power
specifications
Cleaning
For product improvement purposes, design and specifications of the product are subject to change without
prior notice.
Charging and cleaning times may differ according to conditions of use.
(Depth x Height x Length)
Weight 9.5 lbs.
Sensor Ceiling shape recognition (Visionary mapping plus TM)
Button type of POWERbot Touch type
Power voltage 100-240 V~, 50 Hz/60 Hz
Power consumption 80 W
Battery specifications Lithium ion 21.6 V/ 39 Wh
Charging type Automatic charging/Manual charging
Cleaning mode Auto, Spot, Manual
Charging time Approximately 240 minutes
Cleaning time
(Normal mode/ On the basis of hard floor)
15 in x 5.35 in x 14.25 in
Approximately 60 minutes
ENGLISH-26
Page 27
Memo
ENGLISH-27
Page 28
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care center.
Country Customer Care Center Web Site
CANADA 1-800-SAMSUNG (726-7864)
U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us/support
www.samsung.com/ca/support (English)
www.samsung.com/ca_fr/support (French)
DJ68-00740L-01
Loading...