Samsung POWERbot, SR1AM7040W Series, SR1AM7010UW Series, SR1AM70 Series, SR2AM70 Series User Manual
POWERbot
User manual
SR1AM70
, SR2AM70
Series
• Before operating this unit, please read the instructions carefully.
• For indoor use only.
1_VR7000_EN_DJ68-00763C-02_USA.indd 1 2017-02-23 오전 12:26:51
ENGLISH-02
Contents
03
Safety information
10
Installation
Accessories / Installation note
12
Charging
Automatic charging / Recharging / Low
battery (Lo)
14
Using POWERbot
Turning the power on/off / Selecting
cleaning modes/ Using special cleaning
functions/ About the boundary
markers/ Using Energy-saving mode
18
Using the remote control
21
Name of each part
Top / Bottom / Display panel
23
Setting time/schedule
Setting the time / Setting the schedule
26
Cleaning and maintaining
Cleaning the dustbin / Cleaning the sensors and
the camera / Cleaning the brush and Auto shutter
tool / Cleaning the Driving wheel
28
Samsung Smart Home App
Preparing the network / Using the Samsung
Smart Home app
32
Notes and cautions
Charging / Using / Cleaning and maintenance /
About the battery / About the IrDA sensor
34
Information codes
36
Troubleshooting
38
Open Source Announcement
39
Specications
1_VR7000_EN_DJ68-00763C-02_USA.indd 2 2017-02-23 오전 12:26:51
ENGLISH-03
Safety information
SAFETY INFORMATION
WARNING
• Before operating the appliance, please read this manual thoroughly and
retain it for your reference.
WARNING
• Because these following operating instructions cover various models, the
characteristics of your vacuum cleaner may differ slightly from those
described in this manual.
CAUTION/WARNING SYMBOLS USED
WARNING
Indicates that a danger of death or serious injury exists.
CAUTION
Indicates that a risk of personal injury or material damage exists.
OTHER SYMBOLS USED
NOTE
Indicates that a risk of personal injury or material damage exists.
This Smart Robot vacuum supports from Samsung Smart Home.
More detailed information, please visit Samsung.com/Smarthome.
State of California Proposition 65 Warning (US only)
WARNING
This product contains chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
L i - i o n
For battery recycling go to call2recycle.org;
or call 1-800-822-8837
1_VR7000_EN_DJ68-00763C-02_USA.indd 3 2017-02-23 오전 12:26:51
ENGLISH-04
Safety information
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including
the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.
Unplug from outlet when not in use and before conducting maintenance.
WARNING: to reduce the risk of re, electric shock, or injury:
GENERAL
• Use only as described in this manual.
• Do not operate POWERbot or the adapter / docking station if it has been
damaged in any way.
• If the vacuum cleaner is not working as it should, has been dropped, damaged,
left outdoors, or dropped in water, return it to a customer care center.
• Do not handle the adapter / docking station or POWERbot with wet hands.
• Use only on dry, indoor surfaces.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Cleaning and user
maintenance shall not be made by children without supervision.
• Place the cords from other appliances out of the area to be cleaned.
• Do not operate the vacuum in a room where an infant or child is sleeping.
• Do not operate the vacuum in an area where there are lit candles or fragile
objects on the oor to be cleaned.
• Do not operate the vacuum in a room that has lit candles on furniture that the
vacuum may accidentally hit or bump into.
• Do not allow children to sit on the vacuum.
• Do not use the vacuum on a wet surface.
Adapter / Docking station
• Do not modify the polarized plug to t a non-polarized outlet or extension cord.
• Do not use outdoors or on wet surfaces.
• Unplug the adapter / docking station from the outlet when not in use and before
servicing.
• Use only the adapter / docking station supplied by the manufacturer to recharge.
• Do not use with a damaged cord or plug or a loose power outlet.
1_VR7000_EN_DJ68-00763C-02_USA.indd 4 2017-02-23 오전 12:26:51
ENGLISH-05
• Do not pull or carry by the cord, use the cord as a handle, close the door on the
cord, or pull the cord around sharp edges or corners. Keep the cord away from
heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not mutilate or incinerate batteries as they will explode at high temperatures.
• Do not attempt to open the adapter / docking station. Repairs should only be
carried out by a qualied customer care center.
• Do not expose the adapter / docking station to high temperatures or allow
moisture or humidity of any kind to come into contact with the adapter /
docking station.
POWERbot
• Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.
• Do not use without a lter in place. When servicing the unit, never put ngers or
other objects into the fan chamber in case the unit accidentally turns on.
• Do not put any objects into openings. Do not use with any openings blocked;
keep openings free of dust, lint, hair, and anything that may reduce air ow.
• Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not pick up anything that is burning or smoke, such as cigarettes, matches, or
hot ashes.
• Do not use to pick up ammable or combustible liquids such as gasoline, nor use
on areas where they may be present.
• Locations with candles or desk lamps on the oor.
• Locations with unattended res (re or embers).
• Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.
• Do not use POWERbot in an enclosed space lled with vapours given off by oil
based paint, paint thinner, moth proong substances, ammable dust, or other
explosive or toxic vapours.
• Leaks from battery cells can occur under extreme usage or temperature
conditions. If the liquid gets on skin, wash quickly with water. If the liquid gets
into the eyes, ush them immediately with clean water for a minimum of 10
minutes. Seek medical attention.
SAVE THESE INSTRUCTIONS
POLARIZED PLUG INSTRUCTIONS
• To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will t in a polarized outlet only one
way. If the plug does not t fully in the outlet, reverse the plug. If it still does
not t, contact a qualied electrician to install a proper outlet. Do not modify the
plug in any way.
1_VR7000_EN_DJ68-00763C-02_USA.indd 5 2017-02-23 오전 12:26:51
ENGLISH-06
Safety information
REGULATORY NOTICE
1. FCC Notice
CAUTION
FCC CAUTION:
• Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
• This device complies with Part 15 of FCC Rules. Operation is Subject to following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that
cause undesired operation.
• For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
FCC STATEMENT:
• This equipment has been tested and found to comply within the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
• This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver
– Connect the equipment into an outlet on a different circuit from that to which
the receiver is connected
– Consult the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
• This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This device
and its antenna(s) must not be co-located or operation in conjunction with any
other antenna or transmitter.
1_VR7000_EN_DJ68-00763C-02_USA.indd 6 2017-02-23 오전 12:26:51
ENGLISH-07
2. IC Notice
• The term “IC” before the radio certication number only signies that Industry
Canada technical specications were met. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme á la norme NMB-003 du
Canada.
• For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
IC RADIATION EXPOSURE STATEMENT:
• This equipment complies with IC RSS-102 radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body. This device and
its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
Open Source License Notice
• This device uses open source software. Open Source Licenses are available on
the product menu.
• Tap “Settings > Network > Software Update > Legal Information” on the device
for more details.
1_VR7000_EN_DJ68-00763C-02_USA.indd 7 2017-02-23 오전 12:26:51
ENGLISH-08
WARNING
Power related
f Please prevent any risk of electric shock
or re.
– Do not damage the power cord.
– Do not pull the power cord too hard or
touch the power plug with wet hands.
– Do not use a power source other than 100-
240V~ and also do not use a multi outlet to
supply power to number of devices at the
same time. (Do not leave the cord carelessly
on the oor.)
– Do not use a damaged power plug, power
cord or loose power outlet.
f Clean dust or any foreign matters on the
pin and contact part of the power plug.
– There is a risk of electric shock or
malfunction.
WARNING
Before use
f Do not use POWERbot near combustible
materials.
– Place near candle, desktop lamps, replace
or near combustible materials such as
gasoline, alcohol, thinners etc.
f The POWERbot is intended for household
use therefore do not use it in an attic,
basement, storage, industrial building,
out of indoor space, places with moisture
(such as bathroom, laundry), on the table
or shelves.
– The POWERbot can be damaged or
malfunction.
f Be sure POWERbot does not pass through
or touch any kind of liquids.
– The POWERbot can be severely damaged
and it may contaminate other areas if the
wheels pass through liquid.
f Attach the boundary markers on a place
where the POWERbot may fall such as
a stair or banister to prevent product
damage and injury.
– Please keep the cliff sensor clean all the
time for safety.
f Do not spill any liquids on the docking
station.
– There is a risk of re or electric shock.
f Do not use the docking station for
anything other than its intended purpose.
– There is a risk of re or severe damage to
the docking station.
f Always keep the cliff sensor clean for
your safety.
WARNING
In use
f If any abnormal sounds, smells or smoke
come from POWERbot, immediately shut
off the emergency switch at the bottom of
POWERbot and contact a service center.
WARNING
Cleaning and
maintenance
f When power cord is damaged, contact
a service center to get it replaced by a
certied repairman.
– There is a risk of re or electric shock.
f Please check with a Samsung Electronics
service center when exchanging batteries.
– Using batteries from other products can
cause malfunction.
Safety information
1_VR7000_EN_DJ68-00763C-02_USA.indd 8 2017-02-23 오전 12:26:51
ENGLISH-09
CAUTION
Before use
f Insert the dustbin before using
POWERbot.
f Be careful with the followings for proper
automatic recharging.
– Always turn on the power of the docking
station.
– Install the docking station where POWERbot
can easily nd.
– Do not leave any object in front of the
docking station.
f When installing the docking station, do
not leave the cord carelessly on the oor
since POWERbot may get tangled by it.
f Do not use POWERbot on black colored
oors.
– The POWERbot may not be able to operate
normally.
f Do not place any objects within 2ft
(0.5m) to both sides and 4ft (1m) to the
front of the docking station.
f Make sure the docking station's charging
contact is not damaged or have any
foreign matters on it.
f Do not install the docking station in an
area with a dark oor.
– If the oor around the docking station is
dark, recharging is hindered.
f Move any obstacles that may disturb
POWERbot's movement (such as children's
indoor swing or slides) before cleaning.
f Do not use the POWERbot in a place
which is narrower than the turning radius
(2ft (0.5m) or less) of the POWERbot.
f To clean all areas of your house, open all
rooms and attach the boundary markers
on the places where the POWERbot
may get damaged such as a front door,
veranda, bathroom, and stairs for safety.
f For the very low areas where the
POWERbot may get stuck, attach the
boundary markers to prevent the
POWERbot from getting in.
CAUTION
In use
f Using POWERbot on thick carpet may
damage both POWERbot and the carpet.
– The POWERbot cannot pass over carpet that
is thicker than 0.4in (1cm).
f Do not use POWERbot on tables or other
high surfaces.
– There is a risk of damage if it falls.
f The POWERbot may bump into chair, desk
legs therefore move them away for faster
and efcient cleaning.
f When POWERbot is operating, do not lift
it up or carry it to another area.
f Do not hold by driving wheels of
POWERbot when carrying it to another
area.
f Do not put any objects on top of
POWERbot and camera since it may cause
malfunction.
f Remove any large papers or plastic bags
immediately when using POWERbot since
they may block the intake.
f Do not aim the red pointer directly at
people or animals.
f Do not lie down around the POWERBOT
that is running.
– Your hair may be caught in the brush,
resulting in physical injury.
CAUTION
Cleaning and
maintenance
f Prevent any damage to POWERbot by
complying with the following
– Do not clean POWERbot by spraying water
directly onto it or use benzene, thinner,
acetone or alcohol to clean it.
f Do not disassemble or repair POWERbot.
This should only be done by a certied
repairman.
f Always keep the obstacle sensor, cliff
sensor and camera clean.
– If foreign matter accumulates, sensors may
malfunction.
1_VR7000_EN_DJ68-00763C-02_USA.indd 9 2017-02-23 오전 12:26:52
ENGLISH-10
1
Connect the
battery charger
jack to the
docking station
2
Connect the
power cord
to the battery
charger
When using the battery
charger, the side with the
sticker attached must face
down.
3
Connect the
power plug to
the outlet
Installation
The docking station must be plugged in and turned on at all times.
DC-IN
About 4 ft
(1 m)
About
2 ft
(0.5 m)
About
2 ft
(0.5 m)
Install the docking station in
a place without obstacles and
danger of falling.
1_VR7000_EN_DJ68-00763C-02_USA.indd 10 2017-02-23 오전 12:26:52
ENGLISH-11
Accessories
or
Remote control
(Not included with
SR1AM7010UW Series )
Batteries (AAA type) User manual Spare lter
(Option)
Docking station Power cord Battery charger
Boundary markers
(Option)
Refer to page 15 for the installation of boundary markers.
Installation note
Note
f Install the docking station in a place where the oor and wall are level.
f It is best to install the docking station along the grain of wooden oors.
f If the emergency switch is off, the POWERbot will not charge even if it is docked on the
docking station.
f Always turn on the power of the docking station.
– If power is not supplied to the docking station, the POWERbot cannot nd it and cannot
automatically recharge.
– If the POWERbot is left detached from the docking station, the battery will drain naturally.
f If the POWERbot is in sleep mode, power will not come on even if the emergency switch is
turned off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn the
sleep mode off.
1_VR7000_EN_DJ68-00763C-02_USA.indd 11 2017-02-23 오전 12:26:52
ENGLISH-12
After completely charging the POWERbot for the rst time (after purchase), it can be used for 60
min. in Nomal ( ) mode. (Refer to the page 39 for the charging time.)
Smart Charging
If POWERbot runs out of charge in Auto clean mode, it will automatically return to the docking
station to be charged and will recommence the cleaning to complete the cleaning area after twothird of battery charging is done. (Max. 2 times).
Charging
1
Turn on the
emergency switch
on the bottom
You must turn on the
emergency switch to turn on
the POWERbot.
Press and release the
button.
2
Manually charge
the POWERbot by
placing it on the
docking station
Make sure the charging
pins on the POWERbot
and the docking station
are aligned.
3
Check the charging
status
For SR1AM7010UW Series,
The battery indicator blinks at 1 sec.
intervals during charging and the indicator
will remain in ON status when fully charged.
For
SR1AM7040W / SR2AM70 Series,
" " will turn on according to charging
progress and "FULL" will turn on when
charging is complete.
WARNING
• Rated input voltage of
this product is 100240V~.
<SR1AM7040W /
SR2AM70 Series>
<SR1AM7010UW Series>
1_VR7000_EN_DJ68-00763C-02_USA.indd 12 2017-02-23 오전 12:26:52
ENGLISH-13
1. SR1AM7010UW Series
If the battery indicator blinks at 0.4 sec. intervals,
the POWERbot will automatically return to the
docking station to be charged.
2. SR1AM7040W / SR2AM70 Series
When the battery indicator blinks during cleaning,
the POWERbot will return to the docking station to
charge itself automatically.
Automatic charging
You can command the POWERbot to
recharge at the docking station while it is in
cleaning.
Recharging
Manually charge the POWERbot by placing
it on the docking station.
Low battery (Lo)
Steps to take if recharging not occuring:
Check the installation status of the
docking station when:
fthe docking station is located in a place where
the POWERbot cannot easily access it.
fthe distance between the docking station and
POWERbot is over 20ft (5m).
– It may take a long time for POWERbot to
return to the docking station for recharging
Manually charge the POWERbot when:
fthe docking station is located in a corner
fthe battery is fully exhausted
fthe POWERbot is immobilized by an obstacle
(furniture etc.)
fthe POWERbot can't climb a threshold near
the docking station (The maximum height of
a threshold the POWERbot can climb is about
0.6in (1.5cm)).
fwhen the battery indicator blinks and "Lo" is
displayed
fwhen the battery indicator blinks (Applicable to
SR1AM7010UW Series)
fwhen the POWERbot is set to the Spot clean or
Manual clean mode
1_VR7000_EN_DJ68-00763C-02_USA.indd 13 2017-02-23 오전 12:26:53
ENGLISH-14
Using POWERbot
You must turn on the emergency switch on the bottom of the unit before using POWERbot.
Turning the power on/off
Press the button for more than 3seconds
Starting Auto clean mode
Press and release this button. The POWERbot moves
and automatically cleans the set areas only once.
Stop cleaning: Press and release the button
Recharging/Energy-saving mode
fRecharging
You can command POWERbot to recharge at the docking station
automatically while it is cleaning by pressing this button.
fEnergy-saving mode
Refer to page 17.
Using Spot clean mode
The POWERbot cleans a localized area intensely.
WARNING
• When POWERbot is not used for 30 min.;
SR1AM70U / SR2AM70U series: Turns to energy-saving mode.
SR1AM70W / SR2AM70W series: Automatically returns to the docking
station to be charged.
1_VR7000_EN_DJ68-00763C-02_USA.indd 14 2017-02-23 오전 12:26:53
ENGLISH-15
Selecting cleaning modes
Cleaning mode How to select
Displayed icon
SR1AM7040W
SR2AM70
SR1AM7010UW
Auto clean
Spot clean
Repeat clean
Press the [A,B type
],
[C type ] on the remote
controller rst and then press the
[Start/Stop ].
-
Manual clean
Manual clean mode can be
selected by the direction control
buttons of the remote control.
-
If POWERbot fails to return to the docking station, it will turn to energy-saving mode and display
panel will be turned off.
To exit the energy-saving mode, press the [Start/Stop
] or [Power ] button of main body or
remote controller.
If cleaning in Auto clean mode is completed within 15 minutes, POWERbot cleans 1 more time.
1_VR7000_EN_DJ68-00763C-02_USA.indd 15 2017-02-23 오전 12:26:54
ENGLISH-16
Cleaning method for each modes
About 6ft (1.5m)
About 6ft (1.5m)
Auto clean
Automatically cleans the
set areas only once.
SR1AM7010UW series:
Cleans repeatedly
until the battery is
depleted.
Spot clean
Cleans a localized area
intensely. It can be used
to clean bread or cookie
crumbs.
Manual clean
You can move
POWERbot with the
remote control to clean
the desired spot.
This function is
not applicable to
SR1AM7010UW series.
Repeat clean
Cleans repeatedly until
the battery is depleted.
This function is
not applicable to
SR1AM7010UW series.
Note
f If Auto clean or Repeat clean is commenced, POWERbot cleans the area near the docking station rst.
Using special cleaning functions
Cleaning
function
Operation
Displayed icon
SR1AM7040W
SR2AM70
SR1AM7010UW
Intelligent
power control
When the POWERbot detects a
carpet in normal mode, it will
automatically operate with
stronger suction power.
Edge clean
master
When the POWERbot detects an
edge or corner in Auto clean or
Spot clean, the auto shutter tool
operates and approaches the
edge or corner section to clean.
fStraight edge (One time cleaning)
fCorner (Two times cleaning)
Using POWERbot
1_VR7000_EN_DJ68-00763C-02_USA.indd 16 2017-02-23 오전 12:26:54
ENGLISH-17
About the boundary markers
To prevent the POWERbot from entering the following areas, attach
the boundary markers on the oor in the shape at an interval of
about 5.9in (15cm).
About 5.9in
(15cm)
Boundary
markers
About 1.9in
(5cm)
About 5.9in (15cm)
Boundary
markers
where a raised spot is below 1.9in(5cm) where there is a slide, swing, replace or any
ammable substance or moisture.
Above 0.6in (1.5cm)
boundary
markers
Boundary
markers
where a threshold is above 0.6in (1.5cm) where there is risk of falling such as stairs,
porches or guardrails.
Using Energy-saving mode
You may selectthe Energy-saving modeto save energy during battery charging.Energy-saving mode
turns off all functions except battery charging.It reduces the powerconsumptionwhile you are away
from home for an extended period of time.
How to select or cancel Displayed icon
Press for 5 sec.
About 3
seconds later,
the previous
indicator will
appear.
<Only SR1AM7010UW
series>
Blinking Blinking
Note
f If you select the Auto/Max/Manual clean mode or press Point cleaning button, the Energy-
saving mode will be cancelled.
f During the Energy-saving mode, setting the schedule will cancel the Energy-saving mode.
– If you select the Energy-saving mode after setting the schedule, the schedule will not be
cancelled.
f If the power of the docking station is off, the Energy-saving mode will be cancelled.
1_VR7000_EN_DJ68-00763C-02_USA.indd 17 2017-02-23 오전 12:26:55
ENGLISH-18
Using the remote control
[A Type] [B Type]
1 1
1, 2 1, 2
[C Type]
1
3
5
2
Refer to
page 24
4
4
6
1, 2
3 3
5 5
Refer to
page 23
Refer to
page 23
2 2
4
4
4
4
1_VR7000_EN_DJ68-00763C-02_USA.indd 18 2017-02-23 오전 12:26:55
ENGLISH-19
[A Type] / [B Type]/ [C Type]
1 Power / Recharging / Start/Stop
Power
Turn POWERbot's power on/off
Recharging
Select to recharge POWERbot at the docking station
automatically
Start/Stop
Select to start or stop cleaning process
2 Cleaning modes
Auto clean
Select to clean all set areas only once and then
automatically return to the docking station.
Spot clean
Select to clean a localized area intensely
Repeat clean
Select to clean repeatedly until the battery becomes
very low with indicator blinking
3 Suction power
Turbo mode
Select to clean with the strongest suction power
Normal mode
Select to clean with moderate suction power
Quiet mode
Select to clean with lower operation noise
4 Additional function
Sound
Each time you press this button, Sound Effects
Mute is selected in this sequence
Remote control
Select to turn Wi-Fi function on or off
The previously selected setting will not change even if the emergency switch is turned off and then
on.
1_VR7000_EN_DJ68-00763C-02_USA.indd 19 2017-02-23 오전 12:26:56
ENGLISH-20
5 Manual clean mode & Direction control
Move forward
Select to move forward
Turn left
Select to turn left
Turn right
Select to turn right
Moving backward is not available.
6 Point cleaning
Available only with C type remote controllers.
You can use the remote control to point and clean the desired spot while the
POWERbot is in cleaning process.
Point the red light on the oor within 1.6ft (0.5m) around POWERbot's location.
Press and hold the Point cleaning button to move the red light to the desired spot. The POWERbot
will follow the light while cleaning.
1.6ft
(0.5m)
Operating distance of the remote control
Height of the
remote control
Operating distance
Height of the
remote control
1.6ft (0.5m) 3.3ft (1m) 5ft (1.5m)
Operating
distance
About 5ft
(1.5m)
About 6.6ft
(2m)
About 10ft
(3m)
Inserting batteries
Open the battery cover by lifting it
up while pressing the locking tab
and insert the batteries as shown
in the illustration. Then, close the
cover until it clicks into place.
Using the remote control
1_VR7000_EN_DJ68-00763C-02_USA.indd 20 2017-02-23 오전 12:26:57
ENGLISH-21
Name of each part
1
4
2
2
6
5
3
7
8
Top
1. Display panel
2. Remote control signal receiver
3. Obstacle sensor
4. Dustbin
5. Camera
6. Dustbin button
7. Bumper sensor
8. Auto shutter tool
5
5
4
2
3
4
10
7
4
8
9
6
1
Bottom
1. Charge pins
2. Brush
3. Brush cover
4. Cliff sensor
5. Roller
6. Battery cover
7. Brush cover button
8. Driving wheel
9. Emergency switch
10. Auto shutter tool
1_VR7000_EN_DJ68-00763C-02_USA.indd 21 2017-02-23 오전 12:26:57
ENGLISH-22
Name of each part
6
3
5
2
1
4
Display panel
<SR1AM7010UW series>
1. Daily schedule
2. Normal/Turbo mode
3. Battery indicator
4. Spot cleaning button, daily
schedule(3sec)
5. Start/Stop button, Turbo mode(3sec)
6. Recharging button
5
16
15
3
4
7
1
6
2
14
12 138 11109
<SR1AM7040W /
SR2AM70 series>
1. Mute
2. Information Indicator
3. *Smart Control Off/On indicator
4. *Wi-Fi
5. Battery indicator
6. One-time/Daily schedule
7. Number display
8. Spot clean mode
9. Manual clean mode
10. Repeat clean mode
11. Quiet mode
12. Normal mode
13. Turbo mode
14. Spot cleaning button
15. Start/Stop button
16. Recharging button
SR1AM70W / SR2AM70W : Wi-Fi supported model
1_VR7000_EN_DJ68-00763C-02_USA.indd 22 2017-02-23 오전 12:26:58
ENGLISH-23
Setting time/schedule
[A Type, B Type] Only Auto clean mode can be scheduled.
Setting the time
You must set the current time before using the One-time/daily schedule.
Start setting Select "Hour" Select "Minute"
Select "AM/PM"Setting complete
Skip to previous, next setting
Setting the schedule
Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station.
Start setting Select "One-time" or
"Daily" schedule
Select "Hour"
Select "Minute"Select "AM/PM"Setting complete
Skip to previous, next setting
Cancelling during setup
fSetting will be canceled automatically when there's no
input for 7seconds.
Cancelling One-time/Daily schedule
When both One-time/
Daily schedule is set
or
or
Press for 3 sec. Select the schedule Cancel complete
When either one of
One-time or Daily
schedule is set
Press for 3 sec.
1_VR7000_EN_DJ68-00763C-02_USA.indd 23 2017-02-23 오전 12:26:59
ENGLISH-24
Setting time/schedule
[C Type] Only Auto clean mode can be scheduled.
Setting the time
You must set the current time before using the One-time/daily schedule.
Start setting Select "Hour" Select "Minute"
Select "AM/PM"Setting complete
Skip to previous, next setting
Setting the schedule
Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station.
Start setting Select "One-time" or
"Daily" schedule
Select "Hour"
Select "Minute"Select "AM/PM"Setting complete
Skip to previous, next setting
Cancelling during setup
fSetting will be canceled automatically when there's no
input for 7seconds.
Cancelling One-time/Daily schedule
When both One-time/
Daily schedule is set
or or
Press for 3 sec. Select the schedule Cancel complete
When either one of
One-time or Daily
schedule is set
Press for 3 sec.
1_VR7000_EN_DJ68-00763C-02_USA.indd 24 2017-02-23 오전 12:27:00
ENGLISH-25
[SR1AM7010UW series] For the models which do not include a remote controller,
schedule setting is available as below.
Setting the schedule
Press for 3 sec.
When the schedule LED is turned
on, Daily schedule is set.
The time you press the button will be set as a schedule. Cleaning will be automatically done everyday
according to the schedule time.
Cancelling daily schedule
When a daily schedule is set
Press for 3 sec.
1_VR7000_EN_DJ68-00763C-02_USA.indd 25 2017-02-23 오전 12:27:00
ENGLISH-26
Cleaning and maintaining
You must turn off the emergency switch before cleaning POWERbot.
Cleaning the dustbin
1
Press the button to
remove the dustbin
2
Remove the dustbin
cover
3
Remove dust in the
dustbin and cyclone
unit
'Click'
4
Detach the cyclone
unit from the dustbin
cover, and then wash
the dustbin and the
lter
5
Reassemble the
dustbin
6
Reinsert the dustbin
into the main body
until it clicks
Cleaning the sensors and the camera
Lightly wipe with soft cloth. Do not use water or cleaning solutions.
Camera
Front sensor
window
Rear sensor
window
Cliff sensors
1_VR7000_EN_DJ68-00763C-02_USA.indd 26 2017-02-23 오전 12:27:01
ENGLISH-27
Cleaning the brush and Auto shutter tool
Brush design may differ depending on the model.
1
Remove the brush
cover
2
Remove the brush
3
Clean the brush
4
Clean the auto
shutter tool
5
Reassemble the
brush
6
Reassemble the
brush cover
Cleaning the Driving wheel
1
Put a soft cloth on the oor and place
POWERbot upside-down on the cloth.
2
Use a blunt rod or tweezers to remove
foreign matter.
1_VR7000_EN_DJ68-00763C-02_USA.indd 27 2017-02-23 오전 12:27:02
ENGLISH-28
Samsung Smart Home App
Samsung Smart Home App is only applicable to models supported with Wi-Fi function.
Preparing the network
Setting up the wireless router
fThis product supports only DHCP(Dynamic Host Conguration Protocol). Please check if the DHCP
server option function of a wireless router is activated.
fThe supported types of authorization/encryption of the wireless router are WEP-OPEN, WPA-PSK/
TKIP and WPA2-PSK/AES 801.11n.
– WPA2-PSK/AES is recommended to be used.
fThe quality of connection of the wireless network may be inuenced by the surrounding wireless
environment.
fWhen your Internet service provider has permanently registered an MAC address (a unique
identication number) of your PC or modem, your POWERbot may be unavailable to be connected to
the Internet. Ask your Internet service provider about the procedure to connect an apparatus other
than a PC to the Internet.
fIf your internet service provider requires your ID or password to connect to the internet, your
POWERbot may not be able to connect to the internet. In this case, you must enter your ID or
password when connecting to the internet.
fThe connection to the Internet may be impossible because of issues of rewall. Ask your Internet
service provider for resolving the issue.
fSome wireless routers may convey an abnormal Domain Name Server (DNS) address even if the
Internet is not connected. In this case, inquire the provider of the pertinent wireless router and your
Internet service provider.
fIf you still cannot connect to the Internet even after trying the procedure informed by your Internet
service provider, please ask an agency or service center of Samsung Electronics.
Note
f Please refer to the user manual of the pertinent wireless router without access problems.
f Samsung POWERbots support only Wi-Fi 2.4 Ghz.
f Samsung POWERbots support the communication protocol of the methods of IEEE
802.11b/g/n and Wi-Fi Direct. (Samsung Electronics recommends to use IEEE 802.11n.)
f A wireless router with no authorization of Wi-Fi may be unavailable to be connected to the
POWERbot.
f When the power is supplied and the POWERbot is docked on the docking station, the
POWERbot will be connected to the server and then check if there is software updates. If
there is the latest software, it will be automatically downloaded and updated.
f If “UP” is displayed on the display panel while the POWERbot is charging, it means that the
update is in progress. Please wait for completing the rebooting.
1_VR7000_EN_DJ68-00763C-02_USA.indd 28 2017-02-23 오전 12:27:03
ENGLISH-29
f If the product registration is not done, please follow the following instructions:
– Refer to the popup message and retry the registraion procedure.
– Check if the UPnP option of the wireless router is available and retry the registration procedure.
– Check if the operating mode of the wireless router is a router mode and retry the registration
procedure.
– If you have more than two POWERbot, turn off the others to register the one. The connection must
be one to one.
– If there is a wireless router which has the same SSID around your router, a normal registration
cannot be guaranteed.
– Set a unique SSID and password for the wireless router and then register the product.
f Samsung Smart Home Service does not guarantee a normal operation under rewall
environment.
f If the POWERbot and smart phone are not connected to the same wireless router, response
delay may occur according to network environment.
f Smart control and Wi-Fi indicator
– On : Smart control is locked. (Only the remote control is
available.)
–
Off : Smart control is allowed.
–
Off : The POWERbot is connecting to the wireless router.
–
On : The POWERbot is connected to the wireless router.
f If Smart control is locked, you cannot use Samsung Smart Home App.
Using the Samsung Smart Home app
Creating your Samsung account
If you want to use the Samsung Smart Home app, please register your
Samsung account in Samsung account app.
Note
f If you do not set auto-login to the Samsung Smart Home app and
run the app, the screen of Samsung account appears one time at
rst.
f If you are a user of a Samsung smart phone, register your
Samsung account in the settings of the smart phone, and then
the automatic login gets set without any other login processes,
and you can use the Samsung smart home app immediately.
1_VR7000_EN_DJ68-00763C-02_USA.indd 29 2017-02-23 오전 12:27:03
ENGLISH-30
Downloading Samsung Smart Home app
1. Download the Samsung Smart Home application from the Google Play Store (Android devices) or
from the Apple AppStore (iOS devices). To nd the app, use the keyword “Samsung Smart Home.”
2. Install the app on your smart device.
Note
f The Samsung Smart Home app requires Android 4.0 (ICS) or later, and is optimized for Android 4.4
or later on Samsung smartphones (Galaxy S & Note series). Some functions of the app may not work
properly on third-party smartphones.
f For iOS models, the app requires iOS 7 or later.
f The Samsung Smart Home app is subject to change without notice for improvements in usability and
performance.
Registering the product (Easy-Setup)
Register the product to the Samsung Smart Home Service before using the Samsung Smart Home app.
Android
1. Press the Add new icon on the device list screen of the Samsung Smart Home app to start the
registration of the product.
2. Select the Robot vacuum icon.
3. Enter the information of the wireless router to be connected.
4. Set the POWERbot according to the guidance on the screen.
– To turn on the AP mode immediately, press [Clock] button for more than 5 seconds.
5. Then, the registration will proceed automatically.
6. The message will appear when the registration complete.
7. When the product registration is complete, the main screen of the Samsung Smart Home app will
appear.
If the product registration is failed, refer to page 28.
iOS
1. Run Samsung Smart Home app.
2. Move to the left screen and then press the Add new icon on the device list screen to start the
registration of the product.
3. Enter the samsung account and then press [Sign in] button.
– For iPhone, your ID and password is not saved so that you need to sign in everytime you use
Samsung Smart Home app.
4. Select [Robot vacuum] icon.
5. Press the clock button of the remote controller for more than 5 seconds.
– AP will appear on the display panel.
6. Run the Settings app of your iPhone and then connect to [Robot Vacuum] Samsung on the list.
7. Enter ID and password of the wireless router which will be connected and then press [Next] button.
8. The connection between the smart phone and the robot vacuum is in progress.
9. Run the Settings app of your iPhone and then connect to the wireless router which will be
connected on the Wi-Fi list.
Samsung Smart Home App
1_VR7000_EN_DJ68-00763C-02_USA.indd 30 2017-02-23 오전 12:27:03
Loading...