Samsung SR10M7030WW User Manual

POWERbot
User manual
SR10M70
• Before operating this unit, please read the instructions carefully.
• For indoor use only.

, SR20M70

Series
Contents
Safety information
03
Installation
08
Accessories / Installation note
Charging
10
Automatic charging / Recharging / Low battery (Lo)
Using POWERbot
12
Turning the power on/off / Selecting cleaning modes/ Using special cleaning functions
Using the remote control
16
Name of each part
19
Top / Bottom / Display panel
Setting time/schedule
21
Setting the time / Setting the schedule
Cleaning and maintaining
24
Cleaning the dustbin / Cleaning the sensors and the camera / Cleaning the brush and Auto shutter tool / Cleaning the Driving wheel
26
30
32
34
36
37
ENGLISH-02
Samsung Smart Home App
Preparing the network / Using the Samsung Smart Home app
Notes and cautions
Charging / Using / Cleaning and maintenance / About the battery / About the IrDA sensor
Information codes
Troubleshooting
Open Source Announcement
Specications
Safety information
SAFETY INFORMATION
Before operating the appliance, please read this manual thoroughly and
WARNING
WARNING
CAUTION/WARNING SYMBOLS USED
retain it for your reference.
Because these following operating instructions cover various models, the
characteristics of your vacuum cleaner may differ slightly from those described in this manual.
WARNING
CAUTION
OTHER SYMBOLS USED
NOTE
Indicates that a danger of death or serious injury exists.
Indicates that a risk of personal injury or material damage exists.
Indicates that a risk of personal injury or material damage exists.
This Smart Robot vacuum supports from Samsung Smart Home. More detailed information, please visit Samsung.com/Smarthome.
ENGLISH-03
Safety information
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot.
Unplug from outlet when not in use and before conducting maintenance.
WARNING: to reduce the risk of re, electric shock, or injury:
GENERAL
• Use only as described in this manual.
• Do not operate POWERbot or the battery charger / docking station if it has been damaged in any way.
• If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, return it to a customer care center.
• Do not handle the battery charger / docking station or POWERbot with wet hands.
• Use only on dry, indoor surfaces.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Cleaning and user maintenance shall not be made by children without supervision.
Battery charger / Docking station
• Do not modify the polarized plug to t a non-polarized outlet or extension cord.
• Do not use outdoors or on wet surfaces.
• Unplug the battery charger / docking station from the outlet when not in use and before servicing.
• Use only the battery charger / docking station supplied by the manufacturer to recharge.
• Do not use with a damaged cord or plug or a loose power outlet.
• Do not pull or carry by the cord, use the cord as a handle, close the door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
ENGLISH-04
• Do not mutilate or incinerate batteries as they will explode at high temperatures.
• Do not attempt to open the battery charger / docking station. Repairs should only be carried out by a qualied customer care center.
• Do not expose the battery charger / docking station to high temperatures or allow moisture or humidity of any kind to come into contact with the battery charger / docking station.
POWERbot
• Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc.
• Do not use without a lter in place. When servicing the unit, never put ngers or other objects into the fan chamber in case the unit accidentally turns on.
• Do not put any objects into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce air ow.
• Do not pick up toxic materials (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not pick up anything that is burning or smoke, such as cigarettes, matches, or hot ashes.
• Do not use to pick up ammable or combustible liquids such as gasoline, nor use on areas where they may be present.
• Locations with candles or desk lamps on the oor.
• Locations with unattended res (re or embers).
• Locations with distilled alcohol, thinner, ashtrays with burning cigarettes, etc.
• Do not use POWERbot in an enclosed space lled with vapours given off by oil based paint, paint thinner, moth proong substances, ammable dust, or other explosive or toxic vapours.
• Leaks from battery cells can occur under extreme usage or temperature conditions. If the liquid gets on skin, wash quickly with water. If the liquid gets into the eyes, ush them immediately with clean water for a minimum of 10 minutes. Seek medical attention.
ENGLISH-05
Safety information
WARNING
f Please prevent any risk of electric shock
or re.
– Do not damage the power cord. – Do not pull the power cord too hard or
touch the power plug with wet hands.
– Do not use a power source other than 100-
240V~ and also do not use a multi outlet to supply power to number of devices at the same time. (Do not leave the cord carelessly on the oor.)
– Do not use a damaged power plug, power
cord or loose power outlet.
f Clean dust or any foreign matters on the
pin and contact part of the power plug.
– There is a risk of electric shock or
malfunction.
WARNING
f Do not use POWERbot near combustible
materials.
– Place near candle, desktop lamps, replace
or near combustible materials such as gasoline, alcohol, thinners etc.
f The POWERbot is intended for household
use therefore do not use it in an attic, basement, storage, industrial building, out of indoor space, places with moisture (such as bathroom, laundry), on the table or shelves.
– The POWERbot can be damaged or
malfunction.
f Be sure POWERbot does not pass through
or touch any kind of liquids.
– The POWERbot can be severely damaged
and it may contaminate other areas if the wheels pass through liquid.
f Attach the boundary markers on a place
where the POWERbot may fall such as a stair or banister to prevent product damage and injury.
– Please keep the cliff sensor clean all the
time for safety.
Power related
Before use
f Do not spill any liquids on the docking
station.
– There is a risk of re or electric shock.
f Do not use the docking station for
anything other than its intended purpose.
– There is a risk of re or severe damage to
the docking station.
f Always keep the cliff sensor clean for
your safety.
WARNING
f If any abnormal sounds, smells or smoke
come from POWERbot, immediately shut off the emergency switch at the bottom of POWERbot and contact a service center.
WARNING
In use
Cleaning and maintenance
f When power cord is damaged, contact
a service center to get it replaced by a certied repairman.
– There is a risk of re or electric shock.
f Please check with a Samsung Electronics
service center when exchanging batteries.
– Using batteries from other products can
cause malfunction.
CAUTION
f Insert the dustbin before using
POWERbot.
f Be careful with the followings for proper
automatic recharging.
– Always turn on the power of the docking
station.
– Install the docking station where
POWERbot can easily nd.
– Do not leave any object in front of the
docking station.
Before use
ENGLISH-06
f When installing the docking station, do
not leave the cord carelessly on the oor since POWERbot may get tangled by it.
f Do not use POWERbot on black colored
oors.
– The POWERbot may not be able to operate
normally.
f Do not place any objects within 0.5m
to both sides and 1m to the front of the docking station.
f Make sure the docking station's charging
contact is not damaged or have any foreign matters on it.
f Do not install the docking station in an
area with a dark oor.
– If the oor around the docking station is
dark, recharging is hindered.
f Move any obstacles that may disturb
POWERbot's movement (such as children's indoor swing or slides) before cleaning.
f Do not use the POWERbot in a place
which is narrower than the turning radius (0.5 m or less) of the POWERbot.
f To clean all areas of your house, open all
rooms and attach the boundary markers on the places where the POWERbot may get damaged such as a front door, veranda, bathroom, and stairs for safety.
f For the very low areas where the
POWERbot may get stuck, attach the boundary markers to prevent the POWERbot from getting in.
CAUTION
f Using POWERbot on thick carpet may
damage both POWERbot and the carpet.
– The POWERbot cannot pass over carpet
that is thicker than 1 cm.
f Do not use POWERbot on tables or other
high surfaces.
– There is a risk of damage if it falls.
In use
f The POWERbot may bump into chair,
desk legs therefore move them away for faster and efcient cleaning.
f When POWERbot is operating, do not lift
it up or carry it to another area.
f Do not hold by driving wheels of
POWERbot when carrying it to another area.
f Do not put any objects on top of
POWERbot and camera since it may cause malfunction.
f Remove any large papers or plastic bags
immediately when using POWERbot since they may block the intake.
f Do not aim the red pointer directly at
people or animals.
f Do not lie down around the POWERBOT
that is running.
– Your hair may be caught in the brush,
resulting in physical injury.
CAUTION
Cleaning and maintenance
f Prevent any damage to POWERbot by
complying with the following
– Do not clean POWERbot by spraying water
directly onto it or use benzene, thinner, acetone or alcohol to clean it.
f Do not disassemble or repair POWERbot.
This should only be done by a certied repairman.
f Always keep the obstacle sensor, cliff
sensor and camera clean.
– If foreign matter accumulates, sensors may
malfunction.
ENGLISH-07
Installation
The docking station must be plugged in and turned on at all times.
Install the docking station in a place without obstacles and danger of falling.
About 1m
About
0.5m
About
0.5m
DC-IN
Connect the
battery charger
1
jack to the docking station
Connect the
power cord
2
to the battery charger
When using the battery charger, the side with the sticker attached must face down.
ENGLISH-08
Connect the
power plug to
3
the outlet
Accessories
or
Remote control
(Not included with
SR10M701 Series )
Docking station Power cord Battery charger
Refer to page 15 for the installation of boundary markers.
Batteries (AAA type) User manual Spare lter
(Option)
Boundary markers
(Option)
Installation note
Note
f Install the docking station in a place where the oor and wall are level. f It is best to install the docking station along the grain of wooden oors. f If the emergency switch is off, the POWERbot will not charge even if it is docked on the
docking station.
f Always turn on the power of the docking station.
– If power is not supplied to the docking station, the POWERbot cannot nd it and cannot
automatically recharge.
– If the POWERbot is left detached from the docking station, the battery will drain naturally.
f If the POWERbot is in sleep mode, power will not come on even if the emergency switch
is turned off and then on. Press and hold the [Start/Stop] button on the POWERbot to turn the sleep mode off.
ENGLISH-09
Charging
After completely charging the POWERbot for the rst time (after purchase), it can be used for 60 min. in Nomal ( ) mode. (Refer to the page 39 for the charging time.)
Smart Charging
If POWERbot runs out of charge in Auto clean mode, it will automatically return to the docking station to be charged and will recommence the cleaning to complete the cleaning area after two­third of battery charging is done. (Max. 2 times).
• Rated input voltage of
WARNING
this product is 100­240V~.
Turn on the
emergency switch
1
on the bottom
You must turn on the emergency switch to turn on the POWERbot.
Press and release the
button.
Manually charge the POWERbot by
2
placing it on the docking station
Make sure the charging pins on the POWERbot and the docking station are aligned.
ENGLISH-10
<SR10M701 Series>
<SR10M702 / SR10M703 /
SR20M70 Series>
Check the
charging status
3
For SR1M701 Series, The battery indicator blinks at 1 sec. intervals during charging and the indicator will remain in ON status when fully charged.
SR1M702 / SR1M703 /
For
SR2M70 Series
" " will turn on according to charging progress and "FULL" will turn on when charging is complete.
,
Automatic charging
1. SR10M701 Series
If the battery indicator blinks at 0.4 sec. intervals, the POWERbot will automatically return to the docking station to be charged.
2. SR10M70 / SR2070 Series
When the battery indicator blinks during cleaning, the POWERbot will return to the docking station to charge itself automatically.
Recharging
You can command the POWERbot to recharge at the docking station while it is in cleaning.
Low battery (Lo)
Manually charge the POWERbot by placing it on the docking station.
Steps to take if recharging not occuring:
Check the installation status of the docking station when:
fthe docking station is located in a place where the POWERbot cannot easily access it.
fthe distance between the docking station and POWERbot is over 5m.
– It may take a long time for POWERbot to
return to the docking station for recharging
Manually charge the POWERbot when:
fthe docking station is located in a corner fthe battery is fully exhausted fthe POWERbot is immobilized by an obstacle
(furniture etc.) fthe POWERbot can't climb a threshold near
the docking station (The maximum height of a threshold the POWERbot can climb is about
1.5 cm.) fwhen the battery indicator blinks and "Lo" is
displayed fwhen the battery indicator blinks (Applicable
to SR10M701 Series) fwhen the POWERbot is set to the Spot clean or
Manual clean mode
ENGLISH-11
Using POWERbot
You must turn on the emergency switch on the bottom of the unit before using POWERbot.
Turning the power on/off
Press the button for more than 3seconds
• When POWERbot is not used for 30 min.;
WARNING
SR10M70U / SR20M70U series: Turns to energy-saving mode. SR10M70W / SR20M70W series: Automatically returns to the docking
station to be charged.
Starting Auto clean mode
Press and release this button. The POWERbot moves and automatically cleans the set areas only once.
Stop cleaning: Press and release the button
Using Spot clean mode
The POWERbot cleans a localized area intensely.
Recharging
You can command POWERbot to recharge at the docking station automatically while it is cleaning by pressing this button.
ENGLISH-12
Loading...
+ 28 hidden pages