Samsung SP54R1, SP43R1, SP47Q5 User Manual

COLOUR TELEVISION

SP43T8 SP42W4 SP43W6 SP42Q2 SP43Q5/47Q5 SP43R1/54R1

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

TELETEXT SELF FOCUS

Important Warranty Information Regarding Television Format Viewing

Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are

primarily designed to view standard format full-motion video. The images displayed on them

should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary

graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen

pictures), should be limited to no more than 15% of the total television viewing per week.

Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are

primarily designed to view wide screen format full-motion video. The images displayed on them

should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your

model offers this feature, and constantly moving. Displaying stationary graphics and images on

screen, such as the dark side-bars on non-expanded standard format television video and

programming, should be limited to no more than 15% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video

game displays, station logos, web sites or computer graphics and patterns, should be limited as

described above for all televisions. Displaying any stationary images that exceed the above

guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent

burned-in ghost images in the television picture. To avoid this, vary the programming and

images, and primarily display full screen moving images, not stationary patterns or dark bars.

On television models that offer picture sizing features, use these controls to view the different

formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven CRT

aging as a result of format selection and use, as well as other burned-in images, is not covered by

your Samsung limited warranty.

English - 3

Contents

◆ FOREWORD

■ Important Warranty Information Regarding Television Format Viewing ........ 3

◆ CONNECTING AND PREPARING YOUR TELEVISION

■ Control Panels (depending on the model)..................................................... 6~7

■ Connection Panels (depending on the model) .............................................. 8

■ Using a Display Deck (depending on the model) .......................................... 9

■ Inserting the Batteries in the Remote Control................................................ 9

■ Infrared Remote Control ................................................................................ 10

■ Connecting to an Aerial or Cable Television Network ................................... 11

■ Connecting a Satellite Receiver or Decoder.................................................. 12

■ Switching Your Television On and Off........................................................... 13

■ Placing Your Television in Standby Mode..................................................... 14

■ Becoming Familiar with the Remote Control ................................................. 15

■ Plug and Play Feature................................................................................... 16~17

■ Displaying Information ................................................................................... 17

■ Choosing Your Language.............................................................................. 18

■ Adjusting the Screen Automatically (Self Focus)........................................... 19

■ Deactivating the Automatic Execution of the Self Focus............................... 20

■ Removing the “Self Focus” from the Display ................................................. 21

◆ SETTING THE CHANNELS

■ Storing Channels Automatically..................................................................... 22

■ Sorting the Stored Channels ......................................................................... 23

■ Storing Channels Manually............................................................................ 24~25

■ Skipping Unwanted Channels ....................................................................... 26

■ Assigning Names to Channels ...................................................................... 27

■ Locking the Channel...................................................................................... 28

■ Fine Tuning Channel Reception.................................................................... 29

◆ USING YOUR TELEVISION

■ Using the LNA (Low Noise Amplifier) Feature............................................... 30

■ Changing the Picture Standard ..................................................................... 31

■ Customizing the Picture Settings................................................................... 32

■ Selecting the Picture Size (4:3 Model) .......................................................... 33

■ Selecting the Picture Size (Wide Model) ....................................................... 34~35

■ Selecting the Scan Mode............................................................................... 36

■ Using the Digital NR (Digital Noise Reduction) Feature ................................ 37

■ Setting the Blue Screen Mode....................................................................... 38

■ Freezing the Current Picture ......................................................................... 38

■ Changing the Sound Standard ...................................................................... 39

■ Adjusting the Sound Settings ........................................................................ 40

English - 4

Contents (continued)

◆ USING YOUR TELEVISION (continued)

■ Extra Sound Settings..................................................................................... 41

- Auto volume

- Dolby Virtual

■ Setting the Melody Sound ............................................................................. 42

■ Selecting the Sound Mode (depending on the model) .................................. 43

■ Setting and Displaying the Current Time....................................................... 44

■ Setting the Sleep Timer ................................................................................. 45

■ Switching the Television On and Off Automatically ....................................... 46

■ Viewing an External Signal Source ............................................................... 47

◆ USING THE TELETEXT FEATURE

■ Teletext Feature ............................................................................................ 48

■ Displaying the Teletext Information ............................................................... 49

■ Selecting Display Options.............................................................................. 50

■ Selecting a Teletext Page.............................................................................. 51

■ Storing Teletext Pages (depending on the model) ........................................ 52

◆ ADDITIONAL INFORMATION ON CONNECTIONS

■ Connecting to the External Input/Outputs...................................................... 53

■ Connecting to the Audio Output .................................................................... 54

■ Connecting to the RCA Input......................................................................... 55

■ Connecting to the S-Video Input.................................................................... 56

■ Connecting to the Component Input.............................................................. 57

■ Redirecting an Input to the External Output .................................................. 58

◆ RECOMMENDATIONS FOR USE

■ Programming the Remote Control for Other Components ............................ 59~60

- VCR Remote Control Codes...................................................................... 60

- Cable Box (CATV) Remote Control Codes................................................ 60

- DVD Remote Control Codes...................................................................... 60

■ Troubleshooting: Before Contacting Service Personnel................................ 61

Symbols

Press Important Note

☛

➢

English - 5

Control Panels (depending on the model)

The actual configuration on your TV may be different, depending on

➢

your model.

SP43T8

SP43W6

SP42W4

➢

( a ) Input Source Selection

( b ) Menu Display

( c ) Accessing to the Selected Option

on the Menu System

( d ) Volume Adjustment

◆ You can use the C/P. buttons to switch on the TV when it is in standby mode depending on the model.

◆ The

on the remote control.

◆ If the remote control no longer works or your have lost it, you can use controls on the panel of the TV.

+ and C/P. buttons have the same function as the ▲/▼/œ/√ buttons

( e ) Channel Selection

( f ) Remote Control Sensor

( g ) Standby & Timer Indicator

( h ) Power On/Off

English - 6

Control Panels (depending on the model) (continued)

The actual configuration on your TV may be different, depending on

➢

your model.

SP42Q2

SP43Q5 SP47Q5

SP43R1 SP54R1

( a ) Input Source Selection

( b ) Menu Display

( c ) Accessing to the Selected Option

on the Menu System

( d ) Volume Adjustment

( e ) Channel Selection

( f ) Remote Control Sensor

( g ) Standby & Timer Indicator

( h ) Power On/Off

( i ) Picture On/Off

English - 7

Connection Panels (depending on the model)

The actual configuration on your TV may be different, depending on

➢

your model.

Side of the TV

( a )

Video Input

( b )

Audio Input

( c )

S-Video Input

Rear of the TV

Component Input

75Ω Coaxial Connector for Aerial or Cable Network

SCART Audio/Video Input/Output

Audio Output

For further details about connection, refer to pages 53~57.

➢

Whenever you connect an audio or video system to your television, ensure that all elements are switched

☛

off. Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions.

English - 8

Using a Display Deck (depending on the model)

You can display a VCR or DVD Player, etc. by using the display deck.

Inserting the Batteries in the Remote Control

SP43W6

You must insert or replace the batteries in the remote control when you:

◆ Purchase the television

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol ( ) downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆+on the battery against +on the remote control

◆-on the battery against -on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

English - 9

Infrared Remote Control

TELEVISION STANDBY

TELETEXT SIZE SELECTION

TUNER/CABLE NETWORK

ONE OR TWO-DIGIT CHANNEL

TEMPORARY SOUND SWITCH-OFF

MIX BOTH TELETEXT INFORMATION

AND THE NORMAL BROADCAST

IN THE ON-SCREEN MENU

SOUND EFFECT SELECTIOND

PICTURE SIZE/

SELECTION

SELECTION/

TELETEXT STORE

VOLUME INCREASE

VOLUME DECREASE

TELETEXT DISPLAY/

MENU DISPLAY/

TELETEXT INDEX

CONTROL THE CURSOR

MAKE THE REMOTE CONTROL WORKS FOR TV, STB, VCR, CABLE, DVD PLAYER

DIRECT CHANNEL SELECTION

SWITCH REPEATEDLY BETWEEN THE LAST TWO CHANNELS DISPLAYED

NEXT CHANNEL/ TELETEXT NEXT PAGE

EXTERNAL INPUT SELECTION/ TELETEXT MODE (LIST/FLOF) SELECTION

PREVIOUS CHANNEL/ TELETEXT PREVIOUS PAGE

INFORMATION DISPLAY/ TELETEXT REVEAL

EXIT FROM ANY DISPLAY

CONFIRM YOUR CHOICE (STORE OR ENTER)

PICTURE EFFECT SELECTION

SURROUND ON/OFF DIRECTLY

SELF FOCUS

PICTURE FREEZE

TELETEXT SUB-PAGE

REMOTE CONTROL SETUP

TELETEXT CANCEL

IF YOUR REMOTE CONTROL IS

NOT FUNCTIONING PROPERLY,

TAKE OUT THE BATTERIES AND

PRESS THE RESET BUTTON FOR

ABOUT 2~3 SECONDS. RE-INSERT

THE BATTERIES AND TRY USING

THE REMOTE CONTROL AGAIN.

The performance of the remote control may be affected by bright light.

➢

English - 10

SOUND MODE SELECTION

FASTEXT TOPIC SELECTION

AUTOMATIC SWITCH-OFF

VCR/DVD FUNCTIONS;

- REWIND ( )

- STOP ( )

- PLAY/PAUSE ( )

- FAST FORWARD ( )

TELETEXT PAGE HOLD

Connecting to an Aerial or Cable Television Network

To view television channels correctly, a signal must be received by the set from one of the following sources:

◆ An outdoor aerial

◆ A cable television network

◆ A satellite network

1 In the first three cases, connect the aerial or network input cable to

the 75Ω coaxial socket on the rear of the television.

2 If you are using an indoor aerial, you may need to turn it when

tuning your television until you obtain a picture that is both sharp and clear. For further details, refer to:

◆ “Storing Channels Automatically” on page 22.

◆ “Storing Channels Manually” on page 24.

Rear of the TV

Cable Television

Network

English - 11

Connecting a Satellite Receiver or Decoder

In order to watch television programmes broadcast via a satellite network, you must connect a satellite receiver to the rear of TV. Also, in order to descramble a coded transmission signal, you must connect a decoder to the rear of TV.

◆ Using a SCART cable

Connect the receiver (or decoder) SCART cable to one of the SCART connectors on the rear of the television.

◆ Using a coaxial cable

Connect a coaxial cable to the:

Receiver (or Decoder) output socket.

Television aerial input socket.

➢ If you wish to connect both a satellite receiver

(or decoder) and a VCR, you should connect the:

◆ Receiver (or Decoder) to the VCR

◆ VCR to the television

Otherwise, connect the receiver (or decoder) directly to the television.

Rear of the TV

Satellite receiver/

Decoder

English - 12

Switching Your Television On and Off

The mains lead is attached to the rear of your television.

1 Plug the mains lead into an appropriate socket.

The main voltage is indicated on the rear of the television

➢

and the frequency is 50 or 60Hz.

2 Press the “ I ” button (On/Off) on the front or side of the television.

Result

: The Standby indicator on the front of the television

lights up.

3 Press the POWER () button on the remote control to switch

the television on.

Result

: The programme that you were watching last is re-

selected automatically.

If you have not yet stored any channels, No clear picture

➢

appears. Refer to “Storing Channels Automatically” on page 22 or “Storing Channels Manually” on page 24.

4 To switch your television off, press the “ I ” button (On/Off) again.

English - 13

Placing Your Television in Standby Mode

Your television can be placed in Standby mode, in order to reduce the power consumption.

The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1 Press the POWER () button on the remote control.

Result

: The screen is turned off and the Standby indicator on

the front of the television lights up in red.

2 To switch the television back on, simply press the POWER ()

button again.

You can also switch on by pressing the TV () or P

➢

button.

Do not leave your television in Standby mode for long

☛

periods of time (when you are away on holiday, for example). Turn your television off by pressing the “ button (On/Off) on the front or side of the television. It is best to unplug the set from the mains and aerial.

I ”

English - 14

Becoming Familiar with the Remote Control

The remote control is used mainly to:

◆ Change channels and adjust the volume

◆ Set up the television using the on-screen menu system

The following table presents the most frequently used buttons and their functions.

Button Viewing Function Menu Function

Used to display the next stored channel.

Used to display the previous stored channel.

to Used to display the corresponding channels.

For double digit channels, the second digit must be

➢

pushed immediately after the first. Failure to do this will result in a single digit channel being displayed.

-/--

PRE-CH Press the PRE-CH button. The TV will switch to the last

() channel viewed.

MUTE Used to switch the sound off temporarily.

()

Used to select a channel numbered ten or over. Press this button, and the “ Enter the two-digit channel number.

To quickly switch between two channels that are far apart, tune to one channel, then use the numeric buttons to select second channel. Then, use the alternate between them.

Used to increase the volume.

Used to decrease the volume.

To turn the sound back on, press this button again, or

➢

press the or button.

” symbol is displayed.

PRE-CH button to quickly

MENU Used to display the Used to return to the previous

() on-screen menu system. menu or normal viewing.

TV Used to switch the Used to exit from the menu

() television on when it is system and return to normal

EXIT

() disply.

in Standby mode. viewing directly.

Used to:

◆ Display a submenu containing selections for the current menu option.

◆ Increase/decrease a menu option value.

Used to confirm your choice.

Used to exit from the any

English - 15

Plug and Play Feature

Plug & Play

Start Plug & Play

Enter Return

Setup

Nederlands

English

Deutsch

Français

Español

Italiano

Svenska

Português

EEllllhhuuiikkaavv

▼

Time

Plug & Play

Language : English

Self Focus

Blue Screen : Off

▼

Move Enter Skip

When the television is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in Standby mode, press the POWER ()

button on the remote control.

Result

: The message Start Plug & Play is displayed.

√√

2 To start the Plug & Play, press the ENTER () button.

Result

: The options available in the Setup group are displayed

with

Language is selected.

3 Select the appropriate language by pressing the ▲ or ▼ button.

Press the

Result

ENTER () button to confirm the language.

: The message Check antenna input. is displayed.

Plug & Play

Check antenna input.

Enter Skip

Country : China

Move Enter Skip

Enter Skip

Auto Store

Belgum

Germany

Spain

France

Italy Netherlands Switzerland

Sweden United Kingdom Eastern Europe

Others

Start

Clock

Hour Minute

-- --

4 Make sure that the antenna is connected to the TV, and then

press the

Result

ENTER () button.

: The Auto Store menu is displayed with Country is

selected.

5 Select your country by pressing the ▲ or ▼ button. Press the

ENTER () button to confirm your choice.

Result

√√

6 To start the channel store, press the ENTER () button.

: The Search menu is displayed.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the frequency range (with lowest first and highest last). When it has finished, the

To stop the search before it has finished or return to normal

➢

viewing, press the

MENU () button.

Clock menu is displayed.

7 Press the œ or √ button to move to the Hour or Minute.

Set these by pressing the

▲ or ▼ button.

8 Press the ENTER () button.

9 When the setting has finished all, the message Enjoy your

watching.

stored will be activated.

is displayed, and then the channel which has been

√√

Move Adjust Exit

Plug & Play

Enjoy your watching.

English - 16

Plug and Play Feature (continued)

If you want to reset this feature...

1 Press the MENU () button.

Result

: The main menu is displayed.

2 Press the ▲ or ▼ button until the Setup is selected.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

4 Press the ▲ or ▼ button until the Plug & Play option is selected.

Press the

Result

ENTER () button.

: This feature starts with the message Start Plug &

Play

is displayed.

5 For further details on how to set, refer to the opposite page.

Time

Plug & Play

Language : English

Self Focus

Blue Screen : Off

▼

Move Enter Return

Setup

√√

Displaying Information

You can view the channel information and setting status you select by pressing the “INFO ( )” button on the remote control.

P 1

Mono

Picture : Dynamic Sound : Custom 12 : 02

English - 17

Choosing Your Language

Setup

Nederlands

English

Deutsch

Français

Español

Italiano

Svenska

Português

EEllllhhuuiikkaavv

▼

Time

Plug & Play

Language : English

Self Focus

Blue Screen : Off

▼

Move Enter Return

Time

Plug & Play

Language : English

Self Focus

Blue Screen : Off

▼

Move Enter Return

When you start using your television for the first time, you must select the language which will be used for displaying menus and

√√

indications.

1 Press the MENU () button.

Result

: The main menu is displayed.

2 Press the ▲ or ▼ button until the Setup is selected.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

√√

4 Press the ▲ or ▼ button until the Language is selected. Press the

ENTER () button.

Result

: The languages available are listed.

5 Select the appropriate language by pressing the ▲ or ▼ button.

Press the

ENTER () button to confirm your choice.

English - 18

Adjusting the Screen Automatically (Self Focus)

The “Self Focus” feature automatically finds the optimum picture quality when blurring, overlapping colours or incorrect focus occurs. These conditions may be caused by moving your TV.

1 Press the MENU () button.

Result

: The main menu is displayed.

2 Press the ▲ or ▼ button until the Setup is selected.

Result

: The options available in the Setup group are displayed.

Time

Plug & Play

Language : English

Self Focus

Blue Screen : Off

▼

Move Enter Return

Setup

√√

3 Press the ENTER () button.

4 Press the ▲ or ▼ button until the Self Focus is selected.

Press the

Result

ENTER () button.

: The Self Focus is selected.

5 Press the ENTER () button again

Result

: The self focus process begins with the message Self

Focus

and horizontal bar is displayed. During the process, minor distortions of the picture may occur. At this time, the colors may diffuse and a searching action will appear on the edges of the screen. This is a normal part of the adjustment. When it is finished, all of things will disappear and the optimum picture quality can be enjoyed.

You can also set these options simply by pressing the

➢

SELF FOCUS button.

◆ Changing channels and any other signal changes will

➢

pause the self focus until a stable signal has returned. It resumes after the signal has been stabilised. This feature will not work without a signal.

◆ Ambient light that is too bright may affect the self focus. If this occurs, darken the environment and try again.

Self Focus

Auto : On

Message Display : On

Move Enter Return

Self Focus

√√

English - 19

Deactivating the Automatic Execution of the Self Focus

Setup

Self Focus

Off

Time

Plug & Play

Language : English

Self Focus

Blue Screen : Off

▼

Move Enter Return

Self Focus

Auto : On

Message Display : On

The “Self Focus” feature starts on default. It will automatically begin 10 minutes after switching on the power and the appearance of the screen image. To set the optimum picture quality, the

√√

“Self Focus” will automatically begin again after another 30 minutes, as the screen image is then fully stabilised.

1 Press the MENU () button.

Result

: The main menu is displayed.

2 Press the ▲ or ▼ button until the Setup is selected.

Result

: The options available in the Setup group are displayed.

√√

3 Press the ENTER () button

4 Press the ▲ or ▼ button until the Self Focus is selected.

Press the

Result

ENTER () button.

: The options available in the Self Focus group are

displayed.

Move Enter Return

5 Press the ▲ or ▼ button until the Auto is selected.

Press the

ENTER () button.

6 To turn off the automatic execution of the self focus feature, select

Off by pressing the ▲ or ▼ button. Press the ENTER () button to confirm.

English - 20

+ 44 hidden pages