Samsung SP-46L5H User Manual

COLOUR TELEVISION

SP43L2HX SP50L2HX SP61L2HX SP46L5HX SP56L5HX

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

ICTURE IN PICTURE (PIP)

TELETEXT

ENG

Safety Instructions

◆ Do not expose the television to extreme temperature conditions or to extreme humidity conditions.

◆ Do not expose the television to direct sunlight and other sources of heat.

◆ Do not expose the television to any liquids.

◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the

television.

◆ During a storm conditions (especially when there is lightning) unplug the television from the mains socket and aerial.

◆ Do not step on or twist the power cord.

◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.

◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.

◆ If the television is broken, do not try to repair it yourself. Contact qualified service personnel.

◆ If the remote control is not used for a long period of time, remove the batteries and store it in a

cool, dry place.

◆ Do not drop the remote control.

This device is not for use in industrial environments.

ENG

Caution

WARNING: TO PREVENT DAMAGE WHICH MAY RESULT

IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The lightning flash and arrow head within the triangle is a warning sign alerting you of “dangerous voltage” inside the product.

The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.

☛

The main voltage is indicated on the rear of the TV set and the frequency is 50 or 60Hz.

ENG

Contents

◆ FOREWORD

■ Safety Instructions ......................................................................................... 2

■ Caution .......................................................................................................... 3

■ Replacing the Lamp....................................................................................... 6~7

◆ CONNECTING AND PREPARING YOUR TELEVISION

■ Control Panel of Your Television ................................................................... 8~9

■ Connection Panel of Your Television ............................................................ 10

■ Connecting to an Aerial or Cable Television Network ................................... 11

■ Connecting a Satellite Receiver or Decoder.................................................. 11

■ Connecting Additional Speakers ................................................................... 12

■ Inserting the Batteries in the Remote Control................................................ 12

■ Infrared Remote Control ................................................................................ 13

■ Switching Your Television On and Off........................................................... 14

■ Placing Your Television in Standby Mode..................................................... 14

■ Becoming Familiar with the Remote Control ................................................. 15

■ Setting Up Your Remote Control ................................................................... 16

■ Plug & Play Feature....................................................................................... 17

■ Choosing Your Language.............................................................................. 18

◆ SETTING THE CHANNELS

■ Storing Channels Automatically..................................................................... 19

■ Storing Channels Manually............................................................................ 20~21

■ Skipping Unwanted Channels ....................................................................... 22

■ Sorting the Stored Channels ......................................................................... 23

■ Assigning Names to Channels ...................................................................... 24

■ Activating the Child Lock ............................................................................... 25

■ Selecting a Channel by Information............................................................... 26

◆ USING YOUR TELEVISION (continued)

■ Changing the Picture Standard ..................................................................... 27

■ Adjusting the Picture Settings........................................................................ 28

■ Adjusting the Picture Settings (PC or DVI Mode) .......................................... 29

■ Setting the Picture (PC Mode)....................................................................... 30

■ Using the Fine Tune ...................................................................................... 31

■ Viewing the Channel Scan Picture ................................................................ 32

■ Using the LNA (Low Noise Amplifier) Feature............................................... 32

■ Extra Picture Settings .................................................................................... 33

Size

Digital NR

■ DNIe

(Digital Natural Image engine) ............................................... 34

■ Freezing the Current Picture ......................................................................... 34

■ Setting the Blue Screen................................................................................. 35

■ Selecting the Film Mode ................................................................................ 35

ENG

Contents (continued)

◆ USING YOUR TELEVISION

■ Changing the Sound Standard ...................................................................... 36

■ Adjusting the Sound Settings ........................................................................ 37

■ Adjusting the Volume Automatically .............................................................. 37

■ Setting the Dolby Pro Logic........................................................................... 38

■ Adjusting Your Dolby Preferences................................................................. 39

■ Setting the External Sound............................................................................ 40

■ Selecting the Sound Mode (depending on the model) .................................. 41

■ Setting the Melody Sound ............................................................................. 42

■ Setting the Sleep Timer ................................................................................. 43

■ Setting and Displaying the Current Time....................................................... 44

■ Switching the Television On and Off Automatically ....................................... 45

■ Viewing an External Signal Source ............................................................... 46

■ Redirecting an Input to the External Output .................................................. 47

■ Viewing the Picture In Picture (PIP) .............................................................. 48~49

■ Listening to the Sound of the Sub Picture (PC or DVI Mode)........................ 50

◆ USING THE TELETEXT FEATURE

■ Teletext Feature ............................................................................................ 51

■ Displaying the Teletext Information ............................................................... 52

■ Selecting Display Options.............................................................................. 52

■ Selecting a Teletext Page.............................................................................. 53

◆ ADDITIONAL INFORMATION AND CONNECTIONS

■ Connecting to the External Input/Output ....................................................... 54

■ Connecting to the DVD Input......................................................................... 55

■ Connecting to the Audio Outputs................................................................... 55

■ Connecting to the Audio/Video Input............................................................. 56

■ Connecting to the S-Video Input.................................................................... 56

■ Connecting to the DVI Input .......................................................................... 57

■ Connecting to the PC Input ........................................................................... 57

■ Setting up Your PC Software (Windows only) ............................................... 58

■ Input Mode (PC/DVI) ..................................................................................... 59

■ Pin Configurations ......................................................................................... 60

◆ RECOMMENDATIONS FOR USE

■ Troubleshooting: Before Contacting Service Personnel................................ 61

■ Technical Specifications ................................................................................ 62

■ Wiring the Mains Power Supply Plug (UK Only)............................................ 63

☛

➢

Press Important Note

Symbols

ENG

1 Use a screwdriver to remove the screw.

2 Remove the Lamp cover.

3 Use a screwdriver to remove the screws securing the Lamp.

There are 2 screws: one on the up and one on the down. When the screws have been completely unfastened, they will still be connected to the body of the Lamp.

4 Separate the Lamp from the engine by holding the handle and

pulling it out.

5 To reinstall the Lamp, follow these steps in reverse order.

☛

A Projection TV lamp is a consumable item, and should be replaced from time to time for best projector operation. If the screen image becomes dark, or timer, lamp and Temp LEDs flicker off at the same time, you may have to replace the lamp. When changing the lamp, you should first verify the type/model, and then use only the correct lamp replacement. The code for lamp regulation and usage is marked on the label. If you remove the lamp, you can identify this replacement code. You should only replace the lamp with the one of the same regulation code.

◆

If you wish to buy a new lamp,please phone your Service Center or a nearby TV dealer, and tell them the model of your projection unit.

◆

You can identify the lamp type on the left side of TV and the lamp cover.

◆

The TV will be damaged if you use a lamp that is different from the original supplied by the manufacturer. Be sure the replacement lamp is the same model.

◆

Please don't remove the lamp except when replacing with a new one.

◆

Please turn off TV power before changing a lamp and then unplug after waiting 1 minute.

◆

The cooling fan will help cool the lamp so you can safely remove it. The surface of the Lamp is very hot. Please wait for 30 minutes after turning off your projection TV to handle the lamp.

◆

Please keep the old lamp away from flammable articles and children. Dispose of properly.

◆

Don't allow dirt or dust to accumulate inside the lamp cover or on the Lamp.

◆

A dirty cover or lamp can catch fire, explode and cause electric shock.

◆

Please don't touch the front glass of a new lamp or the glass of the lamp container.

◆

If a new lamp is improperly handled,the quality of the screen image can be affected and the expected life span of the lamp can be reduced.

◆

Be sure to tighten the lamp cover on the TV after changing the lamp. Note that the TV will not function if the lamp cover is not securely attached. Please tighten the holding screw on the lamp cover after it has been attached to the TV.

Replacing the Lamp (

SP43L2HX/SP50L2HX/SP61L2HX)

ENG

1 Use a screwdriver to remove the screw.

2 Remove the Lamp cover.

3 Use a screwdriver to remove the screws securing the Lamp.

There are 2 screws: one on the up and one on the down. When the screws have been completely unfastened, they will still be connected to the body of the Lamp.

4 Separate the Lamp from the engine by holding the handle and

pulling it out.

5 To reinstall the Lamp, follow these steps in reverse order.

☛

◆

If you wish to buy a new lamp,please phone your Service Center or a nearby TV dealer, and tell them the model of your projection unit.

◆

You can identify the lamp type on the left side of TV and the lamp cover.

◆

The TV will be damaged if you use a lamp that is different from the original supplied by the manufacturer. Be sure the replacement lamp is the same model.

◆

Please don't remove the lamp except when replacing with a new one.

◆

Please turn off TV power before changing a lamp and then unplug after waiting 1 minute.

◆

The cooling fan will help cool the lamp so you can safely remove it. The surface of the Lamp is very hot. Please wait for 30 minutes after turning off your projection TV to handle the lamp.

◆

Please keep the old lamp away from flammable articles and children. Dispose of properly.

◆

Don't allow dirt or dust to accumulate inside the lamp cover or on the Lamp.

◆

A dirty cover or lamp can catch fire, explode and cause electric shock.

◆

Please don't touch the front glass of a new lamp or the glass of the lamp container.

◆

If a new lamp is improperly handled,the quality of the screen image can be affected and the expected life span of the lamp can be reduced.

◆

Replacing the Lamp (

SP46L5HX/SP56L5HX)

ENG

Control Panel of Your Television

LED Indicators

➢

The actual configuration on your TV may be different, depending on your model.

LED Indicators

( a ) Input Source Selection

( b ) Menu Display

( c ) Channel Selection

( d ) Volume Adjustment

( e ) Confirm your choice (Store or Enter)

( f ) Power On/Off

SP43L2/50L2HX SP61L2HX

SP46L5/56L5HX

ENG

( :On, :Blinking, :Off)

TIMER LAMP STAND BY/TEMP Indication

Standby mode.

A timer pilot lights when Timer Auto On or Off is selected.

Normal operation.

Normal operation (when Timer Auto On or Off is selected).

Lamp is warming up. The normal picture comes on after 25 seconds.

The normal picture comes on after 25 seconds. (when Timer Auto On or Off is selected)

Air vent cover in the rear of the TV is not properly installed.

Inside temperature of the TV is over normal. Clean the air vent cover in the rear of the TV. Turn the TV back on after 1 hour.

The lamp does not work, please contact an authorized Service Center for assistance.

➢

Using the Buttons on the Panel

If the remote control no longer works or you have lost it, you can use controls on the panel of the TV to:

◆

Switch on the TV when it is in Standby mode and select channels ( ▲ C/P. ▼ ).

◆

Access the menu ( MENU ).

◆

Adjust the volume ( +

◆

Switch among Video input modes ( SOURCE ).

Control Panel of Your Television (continued)

ENG

Connection Panel of Your Television

Rear of the TV

➢

The actual configuration on your TV may be different, depending on your model.

a) 75Ω

Coaxial connector for Aerial or Cable Network.

b) AV1 / AV2 / AV3

Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

c) SURROUND SPEAKER (8Ω 15W)

Connectors for external rear speakers.

d) AUDIO OUT

Amplifier (L/R) or powered speaker (WOOFER) connection to take full advantage of the surround sound effect.

e) COMPONENT

Video (Y/PB/PR) and audio (L/R) inputs for Component.

f) PC AUDIO (L/R)

PC or DVI Audio inputs.

g) PC (15 Pin)

PC Video input.

h) DVI (24 Pin)

Video input for device with DVI input.

i) RS-232 (only for service)

Side of the TV

SP46L5/56L5HX

( a ) Video Input

( b ) Audio Inputs

( c ) S-Video Input

SP43L2/50L2HX/61L2HX

ENG

To view television channels correctly, a signal must be received by the set from one of the following sources:

◆ An outdoor aerial

◆ A cable television network

◆ A satellite network

1 In the first three cases, connect the aerial or network input cable to

the 75Ω coaxial socket on the rear of the television.

2 If you are using an indoor aerial, you may need to turn it when

tuning your television until you obtain a picture that is both sharp and clear. For further details, refer to:

◆ “Storing Channels Automatically” on page 19.

◆ “Storing Channels Manually” on page 20.

Connecting to an Aerial or Cable Television Network

Rear of the TV

Cable Television

Network

Connecting a Satellite Receiver or Decoder

In order to watch television programmes broadcast via a satellite network, you must connect a satellite receiver to the rear of TV. Also, in order to descramble a coded transmission signal, you must connect a decoder to the rear of TV.

◆ Using a SCART cable

Connect the receiver (or decoder) SCART cable to one of the SCART connectors on the rear of the television.

◆ Using a coaxial cable

Connect a coaxial cable to the:

Receiver (or Decoder) output socket.

Television aerial input socket.

➢ If you wish to connect both a satellite receiver (or decoder)

and a VCR, you should connect the:

◆ Receiver (or Decoder) to the VCR

◆ VCR to the television

Otherwise, connect the receiver (or decoder) directly to the television.

Rear of the TV

Satellite receiver/

Decoder

ENG

Connecting Additional Speakers

You must insert or replace the batteries in the remote control when you:

◆ Purchase the television

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol ( ) downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆-on the battery against -on the remote control

◆+on the battery against +on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

Inserting the Batteries in the Remote Control

To take advantage of the surround sound system, connect additional speakers.

The speaker terminals are located on the rear of the television:

◆ Two for the left-hand surround speaker (marked L)

◆ Two for the right-hand surround speaker (marked R)

➢

To improve the quality of the sound, connect the:

◆ Red wire to the red terminal

◆ Black wire to the black terminal

ENG

Infrared Remote Control

POWER ON/OFF

DIRECT CHANNEL SELECTION

VOLUME INCREASE

TEMPORARY SOUND SWITCH-OFF

MENU DISPLAY/

TELETEXT INDEX

MOVE TO THE REQUIRED MENU

OPTION/

ADJUST AN OPTION VALUE

RESPECTIVELY

STILL THE MAIN PICTURE

➢

In the PIP mode, the main and

sub pictures are stilled

at the same time.

PICTURE EFFEECT SELECTION

EXTERNAL INPUT SELECTION/ TELETEXT HOLD

SWITCH REPEATEDLY BETWEEN THE LAST TWO CHANNELS DISPLAYED

PICTURE SIZE

EXIT FROM ANY DISPLAY

PREVIOUS CHANNEL/ TELETEXT PREVIOUS PAGE

CONFIRM YOUR CHOICE (STORE OR ENTER)

DISPLAY INFORMATION/ TELETEXT REVEAL

DISPLAY CHANNEL INFORMATION

ONE OR TWO-DIGIT CHANNEL

SELECTION

TUNER/CABLE NETWORK

SELECTION

SOUND EFFECT SELECTION

MAKE THE REMOTE CONTROL WORKS FOR TV, VCR, CABLE-BOX (CATV), DVD PLAYER, OR SET-TOP BOX (STB)

SOUND MODE SELECTION

VOLUME DECREASE

NEXT CHANNEL/ TELETEXT NEXT PAGE

➢

The performance of the remote control may be affected by bright light.

CURRENT TIME DISPLAY/ TELETEXT SUBPAGE

TELETEXT DISPLAY/

MIX BOTH TELETEXT INFORMATION

AND THE NORMAL BROADCAST

DNIe ON/DEMO/OFF/

TELETEXT SIZE SELECTION

AUTOMATIC SWITCH-OFF/

TELETEXT CANCEL

SET THE MBR CODE OF REMOTE

CONTROL FOR THE PRODUCTS

EXCEPT SAMSUNG PRODUCT

(OPTION)

INITIALIZE THE REMOTE CONTROL

SETTINGS WHEN IT HAS SOME

PROBLEMS OR DOESN'T WORK

WELL

➢

Please take off the batteries while

resetting. If not so, the remote

control will get damaged.

FASTEXT TOPIC SELECTION

WHEN YOU PRESS A BUTTON , ‘

’ APPEARS ALONG WITH SELECED MODE (TV, VCR, CATV, DVD OR STB) AND REMAINING BATTERIES ON LED

PIP FUNCTIONS;

- PIP ACTIVATING OR DEACTIVATING

(PIP ON)

- SWAPPING THE MAIN AND THE SUB

PICTURE (SWAP)

- SELECTING THE CHANNEL OF SUB

PICTURE (P

/∨)

VCR/DVD FUNCTIONS;

- STOP

- REWIND (REW)

- PLAY/PAUSE

- FAST FORWARD (FF)

ENG

Your television can be placed in Standby mode, in order to reduce the Power consumption.

The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1 Press the POWER () button on the remote control.

Result

: The screen is turned off and the Standby indicator on

the front of the television lights.

2 To switch the television back on, simply press the POWER ()

button again or a numeric button.

➣

You can also switch on by pressing the P or button.

☛

Do not leave your television in Standby mode for long periods of time (when you are away on holiday, for example). Turn your television off by pressing the “

I ” button (On/Off) on the side of the television. It is best to unplug the set from the mains and aerial.

Placing Your Television in Standby Mode

The mains lead is attached to the rear of your television.

☛

If you have purchased this television in the United Kingdom, refer to page 63 for further instructions on plug wiring.

1 Plug the mains lead into an appropriate socket.

➢

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the “ I ” button (On/Off) on the side of the television.

Result

: The Standby indicator on the side of the television

lights up.

3 Press the POWER () button on the remote control to switch the

television on.

Result

: The programme that you were watching last is re-

selected automatically.

➣

If you have not yet stored any channels, No clear picture appears. Refer to “Storing Channels Automatically” on page 19 or “Storing Channels Manually” on page 20.

4 To switch your television off, press the “ I ”button (On/Off) again.

Switching Your Television On and Off

ENG

Becoming Familiar with the Remote Control

The remote control is used mainly to:

◆ Change channels and adjust the volume

◆ Display the on-screen menu system

The following table presents the most frequently used buttons and their functions.

Button Viewing Function Menu Function

Used to display the next

stored channel.

Used to display the

previous stored channel.

to Used to display the corresponding channels.

➢

For double digit channels, the second digit must be pushed immediately after the first. Failure to do this will result in a single digit channel being displayed.

-/--

Used to select a channel numbered ten or over. Press this button, and the “

” symbol is displayed.

Enter the two-digit channel number.

PRE-CH Used to switch repeatedly between the last two channels

displayed.

Used to increase the

volume.

Used to decrease the

volume.

MUTE Used to switch the sound off temporarily.

➣

To turn the sound back on, press this button again, or press the or button.

MENU Used to display the Used to return to the previous

on-screen menu system. menu or normal viewing.

Used to:

◆ Display a submenu containing selections for the current menu option

◆ Increase/decrease a menu option value

Used to confirm your choice.

EXIT

Used to exit from the menu system and return to normal viewing directly.

ENG

This TV’s remote control can operate almost any VCR, Cable box, DVD, or Set-top box, in addition to controlling the TV.

➣

The remote control is not compatible with the TV manufactured by another company.

1 Turn off your VCR, Cable box, DVD, or Set-top box.

2 Press the SELECT button repeatedly to activate another

component (

VCR, CATV, DVD, STB).

Example

: If you want to program the remote control to operate

your VCR, make sure that

VCR is displayed

3 Press the POWER () button on the remote control.

The component you select should turn on. If it turns on, your remote control is now set correctly.

4 Once your remote control is set up, press the SELECT button any

time you want to use the remote control to operate your VCR, Cable box, DVD, or Set-top box.

➣

◆ When your remote control is in the VCR, CATV, DVD or

STB mode, the volume buttons still control your television’s volume.

◆ When your remote control is in the TV or CATV mode, the VCR control buttons (PLAY, PAUSE, etc.) still operate your VCR.

Setting Up Your Remote Control

VCR

ENG

When the television is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available.

1 If the television is in Standby mode, press the POWER () button

on the remote control.

Result

: The message Plug & Play is displayed. It flickers for

a little while, and then the

Language menu is

automatically displayed.

2 Select the appropriate language by pressing the † or … button.

3 Press the ENTER () button to confirm your choice.

Result

: The message Antenna Input Check is displayed.

4 Make sure that the antenna is connected to the TV, and then

press the

ENTER () button.

Result

: The Country menu is displayed.

5 Select your country by pressing the † or … button.

6 Press the ENTER () button to confirm your choice.

Result

: The Auto Store menu is displayed.

7 To start the search, select the Start and press the ENTER ()

button.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the frequency range, (with lowest first and highest last). The programme originally selected is then displayed.

➢ To stop the search before it has finished or return to normal

viewing, press the

EXIT () or ENTER () button.

8 When it has finished, the message Enjoy your watching is

displayed, and then the channel which has been stored will be activated.

Plug & Play Feature

Plug & Play

Start

Exit

Press ENTER to start Plug & Play.

English

ЬА

Hrvatski

Čeština

Nederlands

Français

Language

Move

Enter Exit

Austria

Belgium

Croatia

Denmark

Finland

France

Germany

Country

Move

Enter Exit

Plug & Play

Start

Exit

Antenna Input Check

Auto Store

Start

Exit

Press ENTER to start channel store.

Channel store in process. Storing 175MHz

18%

Auto Store

Exit

Enjoy your watching

ENG

If you want to reset this feature...

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Plug & Play. Press the

ENTER () button.

Result

: The message Plug & Play is displayed.

5 For further details on how to set, refer to the opposite page.

When you start using your television for the first time, you must select the language which will be used for displaying menus and indications.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Setup.

Result

: The options available in the Setup group are displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Language. Press the ENTER

() button. Result

: The languages available are listed.

5 Select the appropriate language by pressing the † or … button.

6 Press the ENTER () button to confirm your choice.

7 When you are satisfied with your choice, press the EXIT ()

button to return to normal viewing.

Plug & Play Feature (continued)

Choosing Your Language

Setup

Move Enter Return

Time

√√

Plug & Play

√√

Language : English

√√

Melody : Off

√√

Blue Screen : On

√√

AV Setup

√√

Film Mode : Off

√√

Image Lock

√√

Setup

Time

√√

Plug & Play

√√

Language : English

√√

Melody : Off

√√

Blue Screen : On

√√

AV Setup

√√

Film Mode : Off

√√

Image Lock

√√

Setup

Time

√√

Plug & Play

√√

Language : English

√√

Melody : Off

√√

Blue Screen : On

√√

AV Setup

√√

Film Mode : Off

√√

Image Lock

√√

English

ЬА

Hrvatski

Čeština

Nederlands

Français Deutsch

EEllllhhnniikkaavv

Maguar

†

Move Enter Return

ENG

You can scan for the frequency ranges available to you, (availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the

Channel

group are

displayed

3 Press the ENTER () button.

4 Press the † or … button to select Country. Press the ENTER

() button. Result

: The countries available are listed.

5 Select your country (or area) by pressing the † or … button.

➢ If you have selected the Others option but do not wish to

scan the PAL frequency range, store the channels manually (see page 17).

6 Press the ENTER () button to confirm your choice

7 Press the † or … button to select Auto Store. Press the ENTER

() button. Result

: The Auto Store menu is displayed.

8 Select the Start and press the ENTER () button to start the

search.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the frequency range, (with lowest first and highest last). The programme originally selected is then displayed.

➢ To stop the search before it has finished, press the EXIT

()or ENTER () button.

9 When the channels have been stored, you can:

◆ Sort them in the order required (see page 23)

◆ Clear a channel (see page 22)

◆ Fine-tune channel reception if necessary (see page 31)

◆ Assign a name to the stored channels (see page 24)

◆ Activate/deactivate the Digital Noise Reduction feature

(see page 33)

Storing Channels Automatically

Channel

Country : Austria

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

Channel

Country : Austria

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

Austria

Belgium

Croatia

Denmark

Finland France

Gernamy

Iceland Ireland

†

Channel

Country : Austria

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

Channel store in process. Storing 175MHz

18%

Auto Store

Exit

Auto Store

Start

Return

Press ENTER to start channel store.

Move Enter Return

ENG

You can store up to television channels, including those received via cable networks.

When storing channels manually, you can choose:

◆ Whether or not to store each of the channels found

◆ The programme number of each stored channel which

you wish to identify

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

The options available in the

Channel

group are

displayed.

3 Press the ENTER () button.

4 Press the † or … button to select Manual Store. Press the

ENTER () button.

Result

: The Manual Store menu is displayed.

5 If necessary, select the broadcasting standard required. Press the

œ or √ button to select Colour System and press the † or … button. The colour standards are displayed in the following order. (depending on the model).

◆

AUTO- PAL- SECAM

◆

AUTO- NTSC3.58- NTSC4.43- PAL60

6 Press the œ or √ button to select Sound System and press the †

or … button. The sound standards are displayed in the following order. (depending on the model).

◆

BG- DK- I- L

◆

BG- DK- I- M

Storing Channels Manually

Channel

Country : Austria

√√

Auto Store

√√

Manual Store

√√

Edit

√√

Fine Tune

√√

Ch. Scan

√√

LNA : Off

√√

Manual Store

Prog. Colour System Sound System

1 AUTO BG

Channel Search Store

- --

887MHz ?

Manual Store

Prog. Colour System Sound System

1 AUTO BG

Channel Search Store

- --

887MHz ?

Manual Store

Prog. Colour System Sound System

1 AUTO BG

Channel Search Store

- --

887MHz ?

Move Enter Return

œœ √√

Move Adjust Return

œœ √√

Move Adjust Return

œœ √√

Move Adjust Return

+ 44 hidden pages