Samsung SP-46L3HR, SP-50L3HR, SP-56L3HR, SP-61L3HR User Manual

Owner’s Instructions

SP-46L3HR SP-50L3HR SP-56L3HR SP-61L3HR

This device is a Class B digital apparatus.

Table of Contents

Your New Wide TV ............................................................................................6

Replacing the Lamp................................................................................................6

List of Features .......................................................................................................8

Accessories ...........................................................................................................8

Side Panel Buttons..................................................................................................9

Side Panel Jacks ................................................................................................... 9

Front Panel LED Indicators .....................................................................................10

Rear Panel Jacks ..................................................................................................11

Remote Control ....................................................................................................12

Installing Batteries in the Remote Control.....................................................13

Connections .....................................................................................................16

Connecting VHF and UHF Antennas.......................................................................16

Antennas with 300-ohm Flat Twin Leads .....................................................16

Antennas with 75-ohm Round Leads...........................................................16

Separate VHF and UHF Antennas ..............................................................17

Connecting Cable TV and VCR..............................................................................18

Cable without a Cable Box .......................................................................18

Cable with a Cable Box that Descrambles All Channels ...............................18

Connecting a Cable Converter Box............................................................19

Connecting a Cable Converter Box and a VCR ...........................................19

Connecting a Camcorder......................................................................................20

Connecting a DVD Player .....................................................................................21

Connecting to Y,P

Connecting to Audio and Video Jacks ........................................................21

Connecting a DTV Set-Top Box ..............................................................................22

Connecting to Y,PB,PR ...............................................................................22

Connecting to DVI (Digital Visual Interface) .................................................22

Connecting to R,G,B.................................................................................23

Connecting to HDMI (High Definition Multimedia Interface) ..........................23

B,PR ...............................................................................21

Operation........................................................................................................26

Turning the TV On and Off....................................................................................26

Viewing the Menus and On-Screen Displays ...........................................................26

Selecting the Menu Language................................................................................27

Selecting the Antenna Input...................................................................................27

Memorizing the Channels .....................................................................................28

Adding and Erasing Channels...............................................................................29

Changing Channels..............................................................................................30

Selecting Your Favorite Channels ...........................................................................31

Scanning the Channels .........................................................................................32

Labeling the Channels ..........................................................................................33

Picture Control .....................................................................................................34

Sound Control .....................................................................................................36

Setting the Clock..................................................................................................38

Setting the Timers.................................................................................................39

Viewing an External Signal Source ........................................................................41

Assigning Names to External Input Mode ...............................................................42

Freezing the Current Picture ..................................................................................43

Remote Control VCR/DVD Buttons..........................................................................43

English - 2

Special Features ...............................................................................................46

Customizing Your Remote Control ..........................................................................46

Remote Control Codes..........................................................................................47

Fine Tuning Channels ...........................................................................................48

LNA (Low Noise Amplifier)....................................................................................49

Selecting the Color Tone .......................................................................................50

Changing the Picture Size.....................................................................................51

Digital Noise Reduction ........................................................................................52

DNIe

Setting the My Color Control Mode........................................................................54

Setting the Film Mode...........................................................................................56

Viewing Picture-In-Picture.......................................................................................57

Setting the SRS TSXT.............................................................................................64

Choosing a Multi-Channel Sound (MTS) track..........................................................65

Auto Volume ........................................................................................................66

Enjoying the Sound of External Speakers ................................................................67

Setting the Child Lock ...........................................................................................68

Viewing Closed Caption Information ......................................................................70

Setting the Blue Screen Mode................................................................................72

Setting The On/Off Melody ..................................................................................73

Using the Color Weakness Enhancement Feature .....................................................74

(Digital Natural Image engine) ...........................................................53

Activating the PIP .....................................................................................57

Selecting an External Source .....................................................................58

Swapping the Sub Picture and Main Picture................................................59

Changing the Size of the Sub Picture .........................................................60

Changing the Location of the Sub Picture....................................................61

Changing the Channel of the Sub Picture....................................................62

Selecting the Sound Source .......................................................................63

PC Display.......................................................................................................76

Using Your TV as a Computer (PC) Display .............................................................76

How to Connect Your PC to the TV.............................................................76

Setting up Your PC Software (Windows only) ..............................................77

Display Modes.........................................................................................78

Adjusting the Picture Quality .................................................................................79

Changing the Picture Position ................................................................................80

Adjusting the Picture Quality and Position Automatically...........................................81

Initializing the Picture Settings................................................................................82

Changing the Picture Size (PC Mode).....................................................................83

Appendix.........................................................................................................86

Troubleshooting ...................................................................................................86

Cleaning and Maintaining Your TV ........................................................................87

Using Your TV in Another Country..........................................................................87

Specifications ......................................................................................................87

English - 3

SAMSUNG

Your New Wide TV

Replacing the Lamp

•Why do I need to replace the lamp?

The lamp used in a projection TV has a limited lifespan. For the best screen quality it needs to be replaced periodically. After replacing the lamp, the screen quality will be bright and clear as new.

• When do I need to replace it?

It should be replaced when the screen becomes darker, less clear or when all three LEDs on the front (Timer, Lamp, & Temp.) are flashing.

• Check before lamp replacement

1. The lamp must be the same code number and type.

2. The lamp type is indicated on the right side of the TV. It is also indicated on the lamp case.

3. After checking the code number for the lamp, give the code number to the store where you purchased the TV or to a Samsung Service center.

• Caution

1. Replace with the correct code numbered lamp to avoid damage to the TV.

2. Turn the power off and wait for 30 minutes before replacing the lamp as it will be hot.

3. Do not touch the glass part of the lamp with your bare hands nor insert any foreign object inside the cover as it may cause poor screen quality, electric shock or fire.

4. Do not place the old lamp near flammable objects or within the reach of children.

When installing the product, make sure to keep it away from the wall (more than 10cm/4 inches) for ventilation purposes.

• Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.

English - 6

• For replacement, you will need a 5.91 Inches-long Phillips screwdriver and a pair of gloves.

Unplug TV, then use a

screwdriver to remove the screw.

Remove the Lamp cover.

Remove the screws securing

the Lamp by using a screwdriver.

Separate the Lamp from the engine by holding the handle

and pulling it out.

To reinstall the Lamp, follow

these steps in reverse order.

NOTES

• Be sure the replacement Lamp is the same type.

• After replacing the lamp, align the lamp cover with the groove and secure the screw.

• The TV will not turn on if the lamp cover is not correctly closed (as this will activate the

protective circuit).

English - 7

Your New Wide TV

List of Features

Your TV was designed and engineered using the latest technology. It is a full-featured, high-performance unit that exceeds industry standards. In addition, it has these special features:

• Easy-to-operate remote control

• Easy-to-use on-screen menu system you can access from the side panel or remote control

• Automatic timer to turn the TV on and off at any time you choose

• Adjustable picture and sound settings and the ability to memorize your favorite settings

• Automatic channel tuning for up to 181 channels

• A special filter to reduce or eliminate reception problems

• Fine tuning control for the sharpest picture possible

• A built-in multi-channel sound decoder for stereo and bilingual listening

• Built-in, dual channel speakers

• A special sleep timer

• Picture-in-Picture capability that lets you watch two channels at once

• Widescreen TV with adjustable image size

• Life-like clear images provided by DNle technology

• My Color Control Mode for corresponding with your color style

• Color weakness Mode

Accessories

Once you have unpacked your TV, check to make sure that you have all the parts shown here. If any piece is missing or broken, call your dealer.

English - 8

Remote Control

(BP59-00075A)/

AAA Batteries

Warranty Cards (2)/ Registration Card (1)

Instruction Manual/

Safety Guide/

Quick Guide/

Anynet Manual

Anynet Cable

Side Panel Buttons

The buttons on the right side panel control your TV’s basic features, including the on-screen menu system. To use the more advanced features, you must use the remote control.

Press to switch between viewing TV programs and signals from connected components. Press to see the on-screen menu.

Press to lower or raise the volume and to select items when using the on-screen menu.

Press to change channels and move between items on the on-screen menu.

Press to activate (or change) a particular item.

Side Panel Jacks

Use the right side panel jacks to connect a component that is used only occasionally (a camcorder or video game, for example).

Connect the video signal from a camcorder or video game.

Connect the audio signal from a camcorder or video game.

Connect an S-video signal from a camcorder or video game. (S-Video 3 jack and Audio L/R input 3 are used in conjunction.)

English - 9

Your New Wide TV

Front Panel LED Indicators

The three lights on the front panel indicate the status of your TV.

POWER

Press to turn the TV on and off.

Remote Control Sensor

Aim the remote control towards this spot on the TV.

: Light is On : Light is Blinking

: Light is Off

TIMER

• It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.

• The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.

LAMP STAND BY/TEMP Indication

Standby state.

The picture will automatically appear in about 15 seconds.

Auto Timer ON/OFF has been set and the set will automatically be turned on in about 25 seconds.

A cooling fan inside the set is not operating normally.

Lamp cover on rear of the set is not properly shut.

Check if the ventilation hole on the rear of the set is blocked, because if the inner temperature is too high, the power will shut off.

Lamp may be defective. Please contact a certified technician.

English - 10

Rear Panel Jacks

Use the rear panel jacks to connect components such as a VCR. You can connect different components such as VCRs, Set-Top Box and a DVD player etc., because there are two sets of video input jacks and three set of component video input jacks on the rear panel of your TV. For more information, please see “Connections”.

ANTENNA terminals

Two independent cables or antennas can be connected to these terminals. Use “ANT 1 IN” and “ANT 2 IN” terminals to receive a signal from VHF/UHF antennas or your cable system. Use the “ANT 1 OUT” terminal to send the signal being received by the “ANT 1 IN” terminal out to another component (such as a Cable Set-Top Box). The PIP channel can be received only when a signal source is connected to “ANT 1 IN”.

S-VIDEO INPUT jacks

Connects an S-Video signal from an S-VHS VCR or DVD player.

VIDEO/AUDIO INPUT jacks (VCR1, VCR2)

Connect video/audio signals from external sources, such as a VCR or DVD players.

VIDEO/AUDIO OUTPUT jacks

Sends a video signal from the TV to an external source, such as a VCR. Note: It is available only in RF, Video and S-Video modes.

Component1, 2 jacks (Y, PB, PR, L, R)

Use these jacks to connect the component video/audio signals from a DVD player or a set top box when using the component video input jacks.

PC AUDIO INPUT jacks

Connect these to the audio output jacks on your PC.

∏

PC VIDEO INPUT jack

Connect these to the video output jack on your PC .

”

DVI (Digital Video Interface) AUDIO INPUT jacks

Connect to the digital audio output jacks for device with DVI output.

’

DVI (Digital Video Interface) VIDEO INPUT jack

Connect to the digital video output jack for device with DVI output.

HDMI (High Definition Multimedia Interface) VIDEO/AUDIO INPUT jack

Connect to the HDMI jack for device with HDMI output.

Anynet

Please refer to the Anynet Owner’s Instruction. This jack is for repair and software upgrades.

English - 11

Your New Wide TV

Remote Control

You can use the remote control up to about 23 feet from the TV. When using the remote control, always point it directly at the TV. You can also use your remote control to operate your Set-Top Box, VCR, Cable box or DVD player. See pages 46~47 for details.

1. POWER

Turns the TV on and off.

2. S.MODE

Adjust the TV sound by selecting one of the preset factory settings (or select your personal, customized sound settings.)

3. P.MODE

Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings.)

4. +100

Press to select cable channels over 100 on TV.

5. VOL +, VOL

Press to increase or decrease the volume.

6. MUTE

Press to mute the TV sound.

7. ANYNET

Runs the Anynet view functions and sets up Anynet devices.

8. MENU

Displays the main on-screen menu.

9. STILL

Press to stop the action during a particular scene. Press again to resume normal video.

10. P.SIZE

Press to change the picture size.

11. MODE

Selects a target device to be controlled by the Samsung remote control (i.e., TV, STB, VCR, CABLE, or DVD).

12. PRE-CH

Tunes to the previous channel.

13. SOURCE

Press to display all of the available video sources (i.e., TV, Set-Top Box, VCR, DVD, DTV, PC).

14. CH /

Press to change channels.

15. INFO

Press to display information on the TV screen.

16. EXIT

Press to exit the menu.

17. ▲, ▼, œ, √, ENTER

Press to select highlight up, down, left, or right. While using the on-screen menus, press the ENTER to activate (or change) a particular item.

18. MTS (Multichannel Television Stereo)

Press to choose Stereo, Mono or SAP (Secondary Audio Program).

19. SRS

Activates TruSurround.

20. ADD/DEL

Press to add or erase channels in the TV’s memory. Use the ADD/DEL button to memorize and erase the fine tuning after fine tuning channels.

21. SLEEP

Press to select a preset time interval for automatic shutoff.

22. PIP (Picture In Picture)

Activates PIP.

23. FAV.CH (Favorite Channel)

Press to switch between your favorite channels.

24. SET

Used during set up of this remote control, so that it will work compatibly with other devices (Set-Top Box, VCR, Cable box, DVD, etc.)

25. DNIe (Digital Natural Image engine)

Activates DNIe.

26. PIP Controls

SWAP; Press to exchange the video signal that

is currently displayed on the main screen with the signal in the PIP window. CH / ; Press to display the available channels in sequence. (These buttons change channels in the PIP window only.)

27. VCR/DVD Controls

Controls VCR or DVD functions: Rewind, Stop, Play/Pause, Fast Forward.

28. RESET

If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.

English - 12

Installing Batteries in the Remote Control

With normal use, the batteries in the remote control should last about a year. If you notice a performance degradation while using the remote, the batteries may need to be replaced. Make sure you replace both batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote control for a long time, remove the batteries and store them in a cool dry place.

Slide the back cover all the way out to open the battery compartment of

the remote control.

Install two AAA size batteries.

Make sure to match the “+” and

“–” ends of the batteries with the diagram inside the compartment.

Slide the cover back into place.

English - 13

SAMSUNG

Connections

Connecting VHF and UHF Antennas

If you do not have a cable system, you will need to connect an antenna to your TV.

Antennas with 300-ohm Flat Twin Leads

If your antenna looks like this: it has 300-ohm flat twin leads.

Place the wires from the twin

leads under the screws on the

300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws.

Plug the adapter into the

“ANT 1 IN” terminal on the

rear panel.

English - 16

Antennas with 75-ohm Round Leads

If your antenna looks like this: it is an antenna with 75-ohm round leads.

Plug the antenna lead into the

“ANT 1 IN” terminal on the rear panel.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

Connect both antenna

leads to the combiner.

Plug the combiner into the

“ANT 1 IN” terminal on

the rear panel.

English - 17

Connections

Connecting Cable TV and VCR

You can connect different cable systems to your TV, including cable without a cable box, and cable with a cable box that descrambles some or all channels.

Cable without a Cable Box

If you want to connect cable, and you do not need to use a cable box:

Plug the incoming cable

into the “ANT 1 IN”

terminal on the rear panel.

Cable with a Cable Box that Descrambles All Channels

Find the cable that is

connected to the

ANTENNA OUT terminal on your cable box. This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

Connect the other end of

this cable to the “ANT 1

IN” terminal on the rear panel.

English - 18

Connecting a Cable Converter Box

This connection allows you to watch cable and premium channels. You should keep your TV selected to “ANT 1 IN” so that you can use the TV features. When viewing premium channels, select “ANT 2 IN” and tune the TV to channel 3 or 4 (whichever channel is vacant in your area), then use the converter box to change channels. You will need two coaxial cables.

NOTES

• When you use a converter box with

From Cable

your TV, there may be features that you can not program using the remote control, such as programming your favorite channels and blocking channels.

• The output from “ANT 1 OUT” is available when select “Ant.2” in the “Antenna“ channel menu.

Connecting a Cable Converter Box and a VCR

This connection allows you to watch and record basic and premium cable channels, as well as watch videotapes. You should keep your TV selected to “ANT 1 IN” so that you can use the TV’s features. When viewing premium channels or recording with the VCR, select “ANT 2 IN” (whichever channel is vacant in your area), then use the converter box to change channels.

From Cable

TV Rear Panel

Stereo VCR

Caution: If you want to record one channel while watching another channel, a splitter (not included) must be added between the cable and “ANT 1 IN”. One output of the splitter goes to “ANT 1 OUT” and the second output is connected to IN on the cable converter box.

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a S-VHS VCR, use the S-video connections and remove the video cable. Do not connect the video cable and the S-video cable to video1 simultaneously.

When you use a converter box with your TV there may be features that you can not program using the remote control, such as programming your favorite channels and blocking channels.

English - 19

Connections

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. You can use your camcorder to view tapes without using a VCR.

Locate the A/V output jacks

on the camcorder. They are

usually found on the side or back of the camcorder.

Connect a set of audio

cables between the AUDIO

IN jacks on the TV and the AUDIO OUT jacks on the camcorder. If you have mono camcorder, connect L(mono) to camcorder audio out using only one audio cable.

TV Side Panel Camcorder

Camcorder Output Jacks

Connect a video cable between the VIDEO IN (or

S-VIDEO IN) jack on the TV and the VIDEO OUT jack on the camcorder. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables.

English - 20

Connecting a DVD Player

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

Connecting to Y,PB,PR

Connect a set of audio

cables between the

COMPONENT (1 or 2) AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the DVD player.

To enable Component video

viewing, connect a set of

video cables between the COMPONENT (1 or 2) VIDEO (Y, PB, PR) IN jacks on the TV and VIDEO (Y/PB/PRor Y/CB/CR) OUT jacks on the DVD player.

Note: For an explanation of Component video, see your DVD player's owner's manual.

TV Rear Panel

Incoming Cable or Antenna

DVD Player

Connecting to Audio and Video Jacks

Connect a set of audio

cables between the AUDIO

IN (1 or 2) jacks on the TV and the AUDIO OUT jacks on the DVD player.

Connect a video cable

between the VIDEO IN (1

or 2) jack on the TV and the VIDEO OUT jack on the DVD player.

TV Rear Panel

Incoming Cable or Antenna

DVD Player

English - 21

Connections

Connecting a DTV Set-Top Box

Connecting to Y,PB,PR

Connect a set of audio

cables between the

COMPONENT (1 or 2) AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box.

Connect a set of video

cables between the

COMPONENT (1 or 2) VIDEO (Y, PB, PR) IN jacks on the TV and VIDEO (Y/PB/PRor Y/CB/CR) OUT jacks on the Set-Top Box.

Note: For an explanation of Component video, see your Set Top Box owner's manual.

Connecting to DVI (Digital Visual Interface)

Connect a set of audio

cables between the DVI

AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box.

TV Rear Panel

Incoming Cable or Antenna

DTV Set Top Box

TV Rear Panel

English - 22

Connect a video cable

between the DVI IN jack on

the TV and the DVI OUT jack on the Set-Top Box.

Incoming Cable or Antenna

DTV Set Top Box

Connecting to R,G,B

Connect a set of audio

cables between the PC

AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box.

Connect a video cable

between the PC IN jack on

the TV and the R.G.B OUT jack on the Set-Top Box.

Incoming Cable or Antenna

Connecting to HDMI (High Definition Multimedia Interface)

Connect a HDMI cable

between the HDMI IN jack

on the TV and the HDMI OUT jack on the Set-Top Box.

TV Rear Panel

DTV Set Top Box

TV Rear Panel

NOTE

•Please check if the power of HDMI source is on, in case that you fail to select HDMI from the “Source List” even after you connected the cable of HDMI source (DTV Set-Top Box, DVD, etc.) to TV.

Incoming Cable or Antenna

DTV Set Top Box

English - 23

SAMSUNG

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the front panel.

Viewing the Menus and On-Screen Displays

The on-screen menu system allows you to control the settings of your TV. Access the on-screen menu system by pressing the MENU button on the remote control. Once the on-screen menu appears, use the …/†/œ/√/ENTER on your remote control to select menu items and make adjustments. You can also view the on-screen menu system and make some adjustments using the TV’s side panel buttons.

Viewing the Menus

Press the MENU button.

The main menu is displayed. There are five menu groups: “Input”, “Picture”, “Sound”, “Channel” and “Setup”.

Input

Picture

Sound

Channel

Setup

Source List : TV Edit Name Anynet

Input

Move Enter Exit

√ √ √

Press the … or † button to

select to an item you want in the menu. Press the œ, √ or ENTER button to display, change, or use the selected items. Use the ENTER button to enter items in the menu.

Press the EXIT button to exit.

Viewing the Display

Press the INFO button on the remote control. The TV displays the current channel, the status of certain picture and sound settings and the current time.

Picture

Mode : Standard

Input

Color Tone : Warm1 Size : Wide

Picture

Digital NR : On DNIe : On

Sound

Channel

My Color Control Film Mode : Off PIP

Setup

Air 12

Signal Mono

Picture Standard Sound Custom SRS TSXT Off MTS Stereo

- - : - - am

Move Enter Return

√ √ √ √ √ √ √ √

English - 26

Selecting the Menu Language

Choose a language for the on-screen menus: English, Spanish or Portuguese.

Selecting the Antenna Input

Press the MENU button. Press the … or † button to

select “Setup”, then press the ENTER button.

Press the ENTER button to select “Language”. Press the … or † button to

select the appropriate language, then press ENTER button.

Press the EXIT button to exit.

Input

Picture

Sound

Channel

Setup

Input

Picture

Sound

Channel

Setup

Language : English Time Child Lock Caption Blue Screen : Off Melody : On Color Weakness PC

Move Enter Return

Setup

Language : English

Time Child Lock

Caption Blue Screen : Off Melody : On Color Weakness PC

Move Enter Return

English

Español

Português

√

√ √ √ √ √ √ √ √

You can connect to two different signal sources by choosing the antenna input (1 or 2).

Press the MENU button.

Press the … or † button to select

“Channel”, then press the ENTER button.

Press the ENTER button to select

“Antenna”. Press the … or † button to select “Ant.1”

or “Ant.2”, then press ENTER button.

Press the EXIT button to exit.

Input

Picture

Sound

Channel

Setup

Input

Picture

Sound

Channel

Setup

Antenna : Ant.1 Air/Cable : Air Auto Program Add/Delete Favorite Channels Name Fine Tune

Antenna : Ant.1

Air/Cable : Air Auto Program Add/Delete Favorite Channels Name Fine Tune

Channel

▼ More

Move Enter Return

Channel

Ant.1

Ant.2

▼ More

Move Enter Return

√ √ √ √ √ √ √

English - 27

+ 61 hidden pages