Samsung SP-43R1HL User Manual
Infrared Remote Control
TELEVISION STANDBY
TELETEXT SIZE SELECTION
TUNER/CABLE NETWORK
ONE OR TWO-DIGIT CHANNEL
TEMPORARY SOUND SWITCH-OFF
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
IN THE ON-SCREEN MENU
SOUND EFFECT SELECTIOND
PICTURE SIZE/
SELECTION
SELECTION/
TELETEXT STORE
VOLUME INCREASE
VOLUME DECREASE
TELETEXT DISPLAY/
MENU DISPLAY/
TELETEXT INDEX
CONTROL THE CURSOR
MAKE THE REMOTE CONTROL WORKS
FOR TV, STB, VCR, CABLE, DVD
PLAYER
DIRECT CHANNEL SELECTION
SWITCH REPEATEDLY BETWEEN THE
LAST TWO CHANNELS DISPLAYED
NEXT CHANNEL/
TELETEXT NEXT PAGE
EXTERNAL INPUT SELECTION/
TELETEXT MODE (LIST/FLOF)
SELECTION
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
INFORMATION DISPLAY/
TELETEXT REVEAL
EXIT FROM ANY DISPLAY
CONFIRM YOUR CHOICE
(STORE OR ENTER)
PICTURE EFFECT SELECTION
SURROUND ON/OFF DIRECTLY
SELF FOCUS
PICTURE FREEZE
TELETEXT SUB-PAGE
REMOTE CONTROL SETUP
TELETEXT CANCEL
IF YOUR REMOTE CONTROL IS
NOT FUNCTIONING PROPERLY,
TAKE OUT THE BATTERIES AND
PRESS THE RESET BUTTON FOR
ABOUT 2~3 SECONDS. RE-INSERT
THE BATTERIES AND TRY USING
THE REMOTE CONTROL AGAIN.
The performance of the remote control may be affected by bright light.
➢
SOUND MODE SELECTION
FASTEXT TOPIC SELECTION
AUTOMATIC SWITCH-OFF
VCR/DVD FUNCTIONS;
- REWIND ( )
- STOP ( )
- PLAY/PAUSE ( )
- FAST FORWARD ( )
TELETEXT PAGE HOLD
Connecting a Satellite Receiver or Decoder
In order to watch television programmes broadcast via a
satellite network, you must connect a satellite receiver to
the rear of TV. Also, in order to descramble a coded
transmission signal, you must connect a decoder to the
rear of TV.
◆ Using a SCART cable
Connect the receiver (or decoder) SCART cable to one
of the SCART connectors on the rear of the television.
◆ Using a coaxial cable
Connect a coaxial cable to the:
-
Receiver (or Decoder) output socket.
-
Television aerial input socket.
➢ If you wish to connect both a satellite receiver
(or decoder) and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the television
Otherwise, connect the receiver (or decoder) directly
to the television.
Rear of the TV
Satellite receiver/
Decoder
Connecting to the External Input/Outputs
➢
EXT 1 is used for the equipment with an RGB output, such as video game
devices or video disc players.
①
Rear of the TV
or
or
①
This end can be fitted with:
◆ A SCART connector
◆ An S-Video connector and two audio RCA connectors (L+R); EXT 2
◆ Three RCA connectors (VIDEO + AUDIO-L and R)
②
If you have a second VCR and wish to copy cassette tape, connect the
source VCR to
the signal from
EXT 1 and the target VCR to EXT 2 so that you can redirect
EXT 1 to EXT 2.
VCR
②
DVD
③
Decoder /
Video game device
Video disc player
Satellite receiver
➃
③
If you have a decoder, connect the decoder to the VCR and the VCR to the
television.
➃
When you wish to record a programme, connect the receiver to EXT 1 and
the VCR to
Whenever you connect an audio or video system to your
☛
television, ensure that all
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
EXT 2 so that you can redirect the signal from EXT 1 to EXT 2.
elements are switched off.
Loading...