samsung SM-G925F Disassembly & Assembly Guide of Galaxy S6
Disassembly & Assembly
Guide of Galaxy S6
Confidential
HHP Global CS team
Rev 2.0
This material is a property of Samsung Electronics Co., Ltd. Any unauthorized use of this material can be punished
under applicable International and/or domestic law.
- This document cannot be used without Samsung’s Authorization -
Confidential
Revision History
Date Rev Comments Pages
2015.03.02 1.0 - Initial version
- Add Back glass handling guide
2015.03.24 1.1
2015.03.27 1.2 - Add Notice regarding disassembly battery 18
2015.04.06 1.3
2015.04.14 1.4 - Add Caution of handling Ethyl alcohol 16,23
2015.04.23 1.5
2015.04.24 1.6
2015.04.27 1.7 - Add ‘S’ mark for reused battery 25
- Add Torque spec for tightening screws
- Add Battery tape attaching image
- Add Pre-requisite to disassemble with Ethyl alcohol
- Revise the way disassemble Back glass and Battery
- Notice to disassemble Battery before detaching the OCTA
- Add new jig item (Spuit) and arranged the jig list
- Add waiting time for absorption of the alcohol
- Add absorber position
- Delete Tape rework form and Acryl JIG rework form
- Add Important Handling Guide regarding disassembly Back glass
- Add Caution of reusing Battery
13
22
40
10
12~15
21,23
9,10
14
15,27
9
18
25
2015.04.29 1.8
2015.05.15 1.9
- Add notice : Wet 0.3ml alcohol more in case of cotton swab than Spuit
- Add the amount of alcohol in case of detaching Back glass and Battery
- Remove a notice to disassemble Battery before detaching the OCTA
- Change the setting of Mobile dryer and Hot plate to disassemble the OCTA
- This document cannot be used without Samsung’s Authorization -
10
15,23
26
Confidential
Revision History
Date Rev Comments Pages
2015.06.19 2.0
- Add Pre-check point before disassembling Back Glass
- Setting of Mobile dryer and Hot plate to detach Back glass
- Add photos for important handling guide of Back glass
13
14
20
- This document cannot be used without Samsung’s Authorization -
Confidential
Notice
This guide is intended solely for the Samsung Electronics internal training and may contain
trade secret, industrial technology or privileged and confidential information otherwise
protected under applicable law including the Unfair Competition Prevention and Trade Secret
Protection Act. Any unauthorized dissemination, distribution, copying of use of the information
contained in this guide is strictly prohibited and subject to legal action.
All functionality, features, specifications and other product information provided in this
document including, but not limited to, the benefits, design, pricing, components, performance,
availability, and capabilities of the product are subject to change without notice or obligation.
Samsung reserves the right to make changes to this guide and the product described herein,
at anytime, without obligation on Samsung Electronics to provide notification of such change.
- This document cannot be used without Samsung’s Authorization -
Confidential
Contents
1. Difference between Flat and Edge
2. Disassembly
ㆍ Pre-requisite
ㆍ Back Part
ㆍ Front Part
3. Assembly
ㆍ Pre-requisite
ㆍ Non-reusable part (In case of Front part repair)
ㆍ Front Part
ㆍ Back Part
- This document cannot be used without Samsung’s Authorization -
Confidential
Difference between
Flat and Edge
- This document cannot be used without Samsung’s Authorization -
Confidential
Sub PBA
Sub PBA with Touch key Sub PBA without Touch key
Between OCTA and BRK
Flat Edge
Including Touch panel
Separate Sub PBA with detaching OCTA Separate Sub PBA without detaching UB
- This document cannot be used without Samsung’s Authorization -
Confidential
OCTA & UB
Cu Ta pe
Flat Edge
OCTA is recyclable in case of repair.
(Cu tape must be replaced)
- This document cannot be used without Samsung’s Authorization -
UB is NOT recyclable once detached.
(Detach only for UB defect case)
Confidential
Disassembly
- This document cannot be used without Samsung’s Authorization -
Confidential
Pre-requisite (Common)
Tweezers Disassembly stick Screw Driver Anti-static glov es
Glass Absorber(2ea) Anti-static mat
GH81-12119A
(Earth connection)
- This document cannot be used without Samsung’s Authorization -
Confidential
Pre-requisite (To disassemble the OCTA or Glass)
Mobile Dryer
GH81-11901A
Cotton Swab Spuit Alcohol Bottle
OCTA disass’y (Holder) OCTA disass’y(Upper)
GH81-12119A GH81-12833A
New
Ethyl Alcohol
(about 95%)
Add Alcohol 0.3ml
more than using Spuit
GH81-12712N
GH81-12712P
GH81-12712L
- This document cannot be used without Samsung’s Authorization -
IMK 1108948200
Confidential
Disassembly of Back Part
1. Back Glass
2. Rear Case
3. Main PBA
4. Sub PBA (for Edge)
5. Bracket
6. Battery
- This document cannot be used without Samsung’s Authorization -
Confidential
How to disassemble
Disassembly Back Glass - 1
Pre-check point before disassembling Back Glass
1. Check the battery percentage before inputting the device into the mobile dryer.
→ Recommend below 80% of battery percentage (Avoid Full-charged battery)
2. Check the battery ASOC and usage cycle with SW capture tool.
→ Recommend above 80% of ASOC, below 500 counts of usage cycle
3. Check the Back glass status if it is swollen or not.
→ Never input the device whose back glass or OCTA is swollen in the mobile dryer.
Battery percentage
Swollen Window
If the device does not satisfies above conditions,
detach the back glass with Ethyl alcohol instead of
using heating machine (i.e. mobile dryer, hot plate).
Usage cycle & ASOC
- This document cannot be used without Samsung’s Authorization -
Confidential
How to disassemble
Disassembly Back Glass - 2
Mobile dryer Hot plate
- Set 60℃ for 5 minutes to pre-heat the device in case of using the Mobile dryer.
- Set 60℃ for 3 minutes to pre-heat the device in case of using the Hot plate.
- This document cannot be used without Samsung’s Authorization -
Confidential
How to disassemble
Disassembly Back Glass - 3
1. Fix the device on the Disassembly Jig.
2. Align 1 absorber along with the Back glass edge.
[ Notice ]
Recommend using ‘OCTA Disass’y upper JIG to prevent LCD crack.
- This document cannot be used without Samsung’s Authorization -
Confidential
How to disassemble
Disassembly Back Glass - 4
Receiver
Absorber
Absorber
Camera
Absorber
Absorber
OCTA or
Glass
Home key
1. Align the absorbers like above position.
→ Avoid Receiver, Home key, Camera deco
- This document cannot be used without Samsung’s Authorization -
Confidential
How to disassemble
Disassembly Back Glass - 5
1. Put the Disassembly Jig upper and Fix the absorber on the Back glass.
2. Rotate the handle of Jig to disassemble Back glass.
3. Add Alcohol if the Back glass is stuck on the Rear case.
[ Notice ]
Focus on the corner of Back glass when using Ethyl alcohol.
※ Amount of Alcohol : Maximum 0.5ml(Flat), 0.7ml(Edge)
- This document cannot be used without Samsung’s Authorization -
Confidential
How to disassemble
Disassembly Back Glass - 6
1. Gently lift the absorber up to disassemble.
2. Release the absorber and remove the Jig upper.
3. Take the device out and detach the Back glass safely.
[ Notice ]
Ethyl alcohol should not be touched on the print area of battery.
- This document cannot be used without Samsung’s Authorization -
Confidential
Loading...