Samsung SHC-740N, SHC-740P User Manual

SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do 462-703, Korea
TEL : [phone]~8141 FAX : [phone]

•

SAMSUNG OPTO-ELECTRONICS AMERICA,INC.
ELECTRONIC IMAGING DIV.

40 Seaview Drive, Secaucus, NJ 07094, U.S.A
TEL : [phone] FAX : [phone]

•

SAMSUNG TECHWIN MOSCOW OFFICE

Korp 14, 37-A, PR-KT, Lenningradsky, Moscow 125167, Russia
TEL : [phone],9298 FAX : [phone]

www.samsungtechwin.com
www.samsungcctv.com

•

SAMSUNG OPTO-ELECTRONICS UK, LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey KT16 OPS
TEL : [phone] FAX : [phone]

•

TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.

7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China
TEL : [phone](33821) FAX : [phone]

P/No. : Z6806-0669-01A

VAN 05. 09

1/2¨ Ultra Low Light Color Camera

INSTRUCTION MANUAL

SHC-740N/P

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

INFORMATION-This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.

WARNING -Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and

should conform to all local codes.

Features Warning

Fine Picture in Ultra Low
illumination.

SV-III built-in DSP and 1/2 inch CCD allows
bright and high quality images to be captured
in ultra low light condition.

- Color : 0.08Lux (F1.2, 50IRE)

- Turbo : 0.04Lux (F1.2, 50IRE)

- B/W : 0.01Lux (F1.2, 50IRE)

Wide Dynamic Range(WDR)

SV-III DSP has WDR function using flexible
gamma.
It shows natural compensated image in any
environment.

SV-III DSP CHIP

SHC-740 has powerful DSP that can remove
image noise efficiently and it shows clean
and obvious image under low illuminance.

High Resolution

The horizontal resolution of 530TV lines at
Color mode and 570TV lines at BW mode
can be achieved by using a half inch CCD
having 410,000 pixels SONY CCD, which
provides clean, noiseless and reliable pictures.

Day & Night

The camera provides automatic mode change
over by sensing day or night conditions. It
can change color mode in the day condition
for optimal color and BW mode in night
condition for clear identification.

Motion Detection

The camera transmits an alert signal to the
MD Output Terminal when it detects motion
of an object. If you connect an optional alarm
to the camera, you can get the effective
surveillance.

VIDEO/DC Lens Selectable

The camera accepts 2 types of auto iris
lenses (DC type/VIDEO type) and is set with
the VIDEO/DC selection switch.

Miscellaneous Function

The camera provides various miscellaneous
functions which are privacy zone masking,
digital zoom, Burst ON/OFF, SYNC selection
(INT/LL), COLOR / TONE / SHARPNESS
adjustment.

Controlled by OSD menu and
RS-232C

You can control the camera using OSD
menu and RS-232C jack at a remote place.

The camera needs periodic inspection.

Contact an authorized technician for inspection.

Stop using your camera when you find a malfunction.

If you use your camera around smoke or unusual heat for a long time, a
fire may be caused.

Do not Install the camera on a surface that can not support it.

Unless the surface is suitable, it could cause falling or other hazards.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not disassemble the camera.

It may result in fire, electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in fire or other hazards.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should contact either the
retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

54

Contents

Precautions

Composition

Name and Function of Each Part

Front
Side
Bottom
Back

Connection

Lens

• Installing Auto Iris Lens

• Installing C/CS-Mount Lens
Connecting to Monitor
Connecting to Power

8 21

10

11
11

12
13
14

15
15

Operating Your Camera

Configuration of The Menu
Setting Up The Menu

• CAMERA ID

• BACKLIGHT

• WHITE BALANCE

• MOTION DETECTION

• LENS SELECTION

• SHUTTER SPEED CONTROL

• AGC

• SENS-UP

• SSNR

• SPECIAL

Using Reomte Jack / MD Output / D&N Input

19
20

Troubleshooting
Specifications

21
22

23
26
27
28
30
32
34
35
36

37

40
42
44

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

76

Precautions

Do not install the camera in
extreme temperature conditions.

Only use the camera under conditions
where temperatures are between -10˚C
and +50˚C. Be especially careful to provide
ventilation when operating under high
temperatures.

Do not install the camera under
unstable lighting conditions.

Severe lighting change or flicker can
cause the camera to work improperly.

Do not install or use the camera in an
environment where the humidity is high.

It can cause the image quality to be poor.

Do not touch the front lens of the
camera.

It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.

Do not drop the camera or subject
them to physical shocks.

It can cause malfunctions to occur.

Do not expose the camera to rain
or spill beverage on it.

If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.

Notes

• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.

• Please check that the power satisfies the normal specification before connecting
the camera.

Never keep the camera face to
strong light directly.

It can damage the CCD.

Do not expose the camera to
radioactivity.

If it is exposed to radioactivity,
For heated CCD, it will be out of order.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

98

Composition

Name and Function of Each Section

Front

1.SHC-740

2. Auto Iris Lens Plug

3. Remote Plug

4. C-Mount Adapter

5. Instruction Manual

C-Mount Lens Adapter

Used to attach C-mount lens.

Tripod Mounting Bracket
Screw Hole

Used to fix the Tripod mounting
bracket on the top of the camera.

Back Focus Adjustment Lever

Used to adjust back focal length

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1110

Name and Function of Each Section

L

Side

BACK FOCUS ADJUSTMENT LEVER

When you don’t obtain focused point after adjusting lens focus,
adjust the lever.

Auto Iris Lens Connector

Used to connect Auto Iris Lens plug.

DC/VIDEO Selection Switch

Used to choose DC or VIDEO according to the
type of your Auto Iris Lens.

Menu Setup Buttons Cover

Menu Setup Buttons

• SET Button: Used to access menu mode. Also used to confirm the setting.

• UP/DOWN Button: Used to choose the desired menu item. It also moves

• LEFT/RIGHT Button:

the cursor up or down in the menu screen.

Used to change the parameter of the selected menu item.
It also moves the cursor the left or right in the menu screen.

Bottom

Tripod Mounting Hole

Used to install the camera on an optional
tripod. The tripod must be equipped with
the screw specified as shown below.

1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)

Tripod Mounting Bracket

You can remove and install this bracket on the top of the
camera. You must use the supplied screw or the
equivalent (within 4mm). If not, the bracket may not be
fixed properly.

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1312

ConnectionName and Function of Each Section

Back

Video Output Jack

Used to connect an external
video monitor in jack.

D&N

Used to input Day & Night
Control Signal

MD Output Terminal

Used to output motion detection signal.

Frame Ground

Used to connect an AC 24V or DC 12V power source.

Power LED

The LED turns on

when power is supplied.

Remote Jack

Used to connect a remoteplug.

AC / DC Power Terminal

LENS

The lens is not supplied with this camera. Purchase a lens suitable for your
environment. This camera accepts the auto iris lens and both C-and
CS-mount lens.

Notes

If the lens is marked with fingerprints or other marks, the image quality might be poor.
It is recommended to use a high quality lens to improve the image quality under
low illumination.
For using main functions it is recommended to use Auto Iris Lens with DC type.

Installing Auto Iris Lens

1. Peel approximately 8mm from the end of the lens cable outer cover.

approx. 8mm

2. Peel approximately 2mm from the end of the cable inner cover.

approx. 2mm

COLOR CCD CAMERACOLOR CCD CAMERA User’s ManualUser’s Manual

1514