Samsung SFG-D1100 Installation Manual

Radio Access Network

5G CPE Outdoor

Installation Manual

Describes product installation and requirement procedure.

Document Version 1.0

December 2017

Document Number: TBA

must be kept confidential. No part of this document shall be photocopied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise without the prior written permission of SAMSUNG Electronics Co., Ltd.

No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted by law no liability (including liability to any person by reason of negligence) will be accepted by SAMSUNG Electronics Co., Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document. SAMSUNG Electronics Co., Ltd. reserves the right to change details in this publication without notice.

SNMTC-v3-0312

This manual should be read and used as a guideline for properly installing and/or operating the product. Owing to product variations across the range, any illustrations and photographs used in this manual may not be a wholly accurate depiction of the actual products you are using. This manual may be changed for system improvement, standardization and other technical reasons without prior notice. Samsung Networks documentation is available at http://www.samsungdocs.com

Confidential

Contents

Preface vi

Conventions in this Document ........................................................................................................ vi

New and Changed Information ...................................................................................................... vii

Revision History .............................................................................................................................. vii

Organization of This Document ..................................................................................................... vii

Related Documentation ................................................................................................................. vii

Personal and Product Safety .......................................................................................................... viii

Equipment Markings ....................................................................................................................... xii

Chapter 1 Before Installation 1

System View and External Interface ................................................................................................ 1

CPE Outdoor View ........................................................................................................................ 1

CPE Outdoor External Interface ................................................................................................... 3

Specifications ................................................................................................................................... 4

Cautions for Installation ................................................................................................................... 5

Before Installing ........................................................................................................................... 5

While Installing ............................................................................................................................ 5

After Installing ............................................................................................................................. 5

Installation Tools .............................................................................................................................. 7

Chapter 2 Installing System 9

Installation Procedure ...................................................................................................................... 9

System Arrangement ..................................................................................................................... 10

Transporting and Unpacking .......................................................................................................... 11

Bringing in Items ........................................................................................................................ 11

Unpacking Items ........................................................................................................................ 11

Fixing System .................................................................................................................................. 12

Fixing Unit Bracket Assembly ..................................................................................................... 12

Fixing System on a Pole Type ..................................................................................................... 13

Fixing System on a Wall Type .................................................................................................... 17

Chapter 3 Inspect the Installation 23

Appendix A Acronyms 27

Appendix B Standard Torque 28

Confidential

List of Figures

Figure 1. CPE Outdoor View ............................................................................................................................ 1

Figure 2. CPE Outdoor View(include Cable Cover) .......................................................................................... 2

Figure 3. CPE Outdoor External Interface ....................................................................................................... 3

Figure 4. Procedure to Install the CPE Outdoor .............................................................................................. 9

Figure 5. CPE Outdoor Arrangement Pole type Installation.......................................................................... 10

Figure 6. CPE Outdoor Arrangement Wall type Installation ......................................................................... 10

Figure 7. Fixing Unit Bracket Assembly(1) ..................................................................................................... 12

Figure 8. Fixing Unit Bracket Assembly(2) ..................................................................................................... 13

Figure 9. Fixing Mounting bracket on the Pole (1) ........................................................................................ 14

Figure 10. Fixing Mounting bracket on the Pole (2) ........................................................................................ 15

Figure 11. Fixing Mounting bracket on the Pole (3) ........................................................................................ 16

Figure 12. Fixing CPE Outdoor on the Pole Mounting Bracket ....................................................................... 17

Figure 13. CPE Outdoor Marking Dimensions for Wall Type .......................................................................... 18

Figure 14. Marking Wall Type ......................................................................................................................... 19

Figure 15. Fixing Mounting Bracket on a Wall (1) ........................................................................................... 21

Figure 16. Fixing Mounting Bracket on the Wall(2) ........................................................................................ 21

Figure 17. Fixing CPE Outdoor on the Wall Mounting Bracket ...................................................................... 22

Figure 18. Installation Inspection Procedure .................................................................................................. 23

Confidential

List of Tables

Table 1. Specifications ................................................................................................................................... 4

Table 2. Basic Installation Tools ..................................................................................................................... 7

Table 3. Parts and Tools for Fixing Unit Bracket on CPE Outdoor ............................................................... 12

Table 4. Parts and Tools for Fixing Mounting bracket on the Pole .............................................................. 13

Table 5. Parts and Tools for Fixing CPE Outdoor on the Pole ...................................................................... 16

Table 6. Tools for Marking ........................................................................................................................... 17

Table 7. Tools for Drilling ............................................................................................................................. 19

Table 8. Anchor Bolt Drill Bits and Hole Depth ............................................................................................ 19

Table 9. Drilling Example ............................................................................................................................. 20

Table 10. Parts and Tools for Fixing Mounting Bracket on the Wall .............................................................. 20

Table 11. Parts and Tools for Fixing CPE Outdoor on the Wall ...................................................................... 22

Table 12. Construction Situation Checklist .................................................................................................... 24

Table 13. Standard Torque Value for Fastening Bolts ................................................................................... 28

Table 14. Brass Bolts Torque Value................................................................................................................ 28

Table 15. Connector Connection Torque Value ............................................................................................. 28

Confidential

Preface

This manual describes how to install a 5G CPE Outdoor and how to connect its cables. This manual includes the following 5G CPE Outdoor:

 CPE Outdoor

Conventions in this Document

Samsung Networks product documentation uses the following conventions.

Symbols

Symbol

Description

Indicates a task.

Indicates a shortcut or an alternative method.

Provides additional information.

Provides information or instructions that you should follow to avoid service failure or damage to equipment.

Provides information or instructions that you should follow to avoid personal injury or fatality.

Provides antistatic precautions that you should observe.

Menu Commands

menu | command

This indicates that you must select a command on a menu, where menu is the name of the menu, and command is the name of the command on that menu.

File Names and Paths

These are indicated by a bold typeface. For example: Copy filename.txt into the /home/folder1/folder2/bin/ folder.

User Input and Console Screen Output Text

Input and output text is presented in the Courier font. For example,

context <designated epc-context-name>

CLI commands are presented in bold small caps. For example, Type the RTRV-NE-STS command in the input field.

Confidential

Preface

New and Changed Information

The following table describes information that has been added/changed since the previous publication of this manual.

Change Type

Change Description

Revision History

The following table lists all versions of this document.

Document Version

Publication Date

Remarks

1.0

February 2018

First version

Organization of This Document

Section

Title

Description

Chapter 1

Before Installation

This chapter introduces CPE Outdoor and describes items should be understood before installation.

Chapter 2

Installing System

This chapter describes the procedures to install the CPE Outdoor.

Chapter 3

Connecting Cables

This chapter describes the procedures to connect the cables to the CPE Outdoor installed.

Chapter 4

Inspect the Installation

This chapter describes the procedures of inspecting installation status after CPE Outdoor installation and cabling is completed.

Appendix A

Acronyms

This annex describes the acronyms used in this manual.

Appendix B

Clean the Optical Connectors

This annex describes the procedure of cleaning the optical connector and cleaning tool.

Appendix C

Standard Torque

This annex describes the standard torque when fastening the bolt.

Related Documentation

 5G RAN System Description

Confidential

Preface

Personal and Product Safety

This product safety information includes European directives, which you must follow. If these do not apply in your country, please follow similar directives that do apply in your country.

Proposition 65 Warning (US Only)

State of California Proposition 65 Warning (US only) WARNING: This product contains chemicals known to the State of California to

cause cancer and birth defects or other reproductive harm.

Electrical

The product is designed to operate from a -48 V DC supply and is therefore classified as Safe Extra Low Voltage (SELV) equipment.

All structural parts are grounded and all input and outputs have built-in isolation from the network. All input and output ports that connect to external power sources are designed to meet relevant national safety requirements.

The product contains hazardous energy levels as defined by EN 60950. Care must be taken when maintaining this equipment as injury to personnel or damage to the equipment could result from mistakes. Maintenance should only be carried out by trained and competent engineers who are familiar with the relevant procedures and instructions.

Lasers

The product is fitted with optic modules rated as Class 1 radiation-emitting devices under EN 60825-1. During installation, operation, and maintenance, never look into the end of an optical fiber directly or by reflection either with the naked eye or through an optical instrument. Do not operate equipment with exposed fiber connectors-cover these with fiber cables or blanking caps. Do not remove equipment covers during operation unless requested to do so in the documentation. Carry out normal safety precautions when trimming fibers during installation.

Manual Handling

Care should be taken when handling equipment. Give due consideration to the weight of the equipment, the physical capability of the individual(s) handling the equipment, and movements such as twisting, bending and stooping, which could lead to skeletal and muscular injuries.

Installation

Installation must be carried out by trained and competent engineers only. All relevant safety measures should be taken to ensure equipment is not connected to

Confidential

Preface

live power and transmission sources during installation. Equipment must be correctly installed in order to meet the relevant safety standards and approval conditions.

Each power feed to the unit requires a separate fused feed from the provided power supply. The cable between the power distribution point and the installed equipment must have a minimum cross-sectional area of 2.5 mm2.

Rack-mountable equipment must be placed in a standard 19-inch rack and secured with the appropriate fixings as detailed in the installation manual.

Maintenance

Maintenance must only be carried out by a suitably trained and competent technician. All safety instructions must be carefully observed at all times. Equipment covers should not be removed while live power and transmission is connected unless in a controlled environment by trained technicians.

Fire

The product is powered from a -48 V DC supply. To protect against fire, the equipment is fused.

Environment

The product must be operated in an environment with the specified relative humidity and ambient temperature ranges.

Keep all liquids away from the equipment as accidental spillage can cause severe damage.

Cooling

The product cools down by its own set of cooling fans housed in a fan module. Each fan module detects a fan that is not operating normally. LEDs on the front panel of the fan module provide an alarm indication in the event of fan failure.

In the event of fan failure, take urgent remedial action to restore full cooling capacity.

Take appropriate measures to ensure that fan modules do not start spinning during repair and maintenance procedures.

Anti-Static Precautions

The circuit boards and other modules in the product are sensitive to and easily damaged by static electricity. If any card or sub-assembly is removed from the unit, the following anti-static precautions must be observed at all times:

 Service personnel must wear anti-static wrist straps.  Circuit boards and sub-assemblies must be placed on ground conductive mats

Confidential

Preface

or in conductive bags.

 All tools must be discharged to ground before use.  The anti-static wrist strap and cord must be checked at regular intervals for

their suitability for use.

Grounding

To comply with EN 60950, the equipment must be connected to a safety grounding point via a permanent link. Grounding points are located on the product for this purpose. Always connect the ground cable before fitting other cables. The product must remain grounded continuously unless all connections to the power supply and data network are all removed.

If equipment is grounded through a cabinet or rack, make sure it is done so properly according to the installation instructions.

Power Supply Connection

The equipment is designed to be powered from a -48 V DC supply. Power connections and installation of associated wiring must be carried out by a suitably qualified technician.

Only devices that comply with all relevant national safety requirements should be connected to the unit’s power supply inlets. Other usage will invalidate any approval given to this equipment.

Connection of this equipment to devices that are not marked with all relevant national safety requirements may produce hazardous conditions on the network.

When the power supply is obtained by a rectifier/safety isolation transformer, the supply must meet the requirements of EN 60950 providing double/reinforced insulation between hazardous voltages and SELV/TNV circuits. Any battery must be separated from hazardous voltages by reinforced insulation.

Indirect Connection

Before indirectly connecting any equipment to another device through a shared power supply, ALWAYS seek advice from a competent engineer.

Devices that are not marked according to the relevant national safety standards may produce hazardous conditions on the network.

Product Disposal

To reduce the environmental impact of products, Samsung has joined WEEE compliance activities.

The WEEE symbol on the product indicates that the product is covered by the European Directive 2002/96/CE for the disposal of Waste Electrical and Electronic Equipment (WEEE). This means that the product should be disposed of separately from the municipal waste stream via designated collection facilities appointed by

Confidential

Preface

the government or the local authorities. This will help prevent potential negative consequences for the environment and human health. Please check the terms and conditions of the purchase contract for information about correct disposal.

Battery Disposal

The product contains a battery on the processor card. The battery should not be disposed of with other household waste. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. The battery incorporated in this product is not user replaceable. For information on its replacement, please contact your service provider. Do not attempt to remove the battery or dispose it in a fire. Do not disassemble, crush, or puncture the battery.

End of life recycling materials information is available from Samsung.

California USA Only

This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA

‘Perchlorate Material-special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.’

Confidential

Preface

Equipment Markings

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product (Applicable in countries with separate collection systems.)

The marking on the battery, manual or packaging indicates that the battery in this product should not be disposed of with other household waste. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.

The battery incorporated in this product is not user replaceable. For information on its replacement, please contact your service provider. Do not attempt to remove the battery or dispose it in a fire. Do not disassemble, crush, or puncture the battery. If you intend to discard the product, the waste collection site will take the appropriate measures for the recycling and treatment of the product, including the battery.

Protective earth

CPE Outdoor should be grounded.

Confidential

Chapter 1 Before

Installation

This chapter introduces CPE Outdoor and describes the items that you should know before installation.

System View and External Interface

This section provides the pictorial view of the CPE Outdoor and its interfaces.

CPE Outdoor View

Figure below depicts the physical structure of the CPE Outdoor.

Figure 1. CPE Outdoor View

[Bottom View]

[Top View]

[Left View]

10.19 (259)

2.08

(53)

Unit: in. (mm)

[Right View]

[Rear View]

[Front View]

6.77 (172)

2.52

(64)

+ 28 hidden pages