Samsung SCO-6081R User Manual

HD-SDI CAMERA

User Manual

SCO-6081R

HD-SDI Camera

User Manual

Copyright

©2013 Samsung Techwin Co., Ltd. All rights reserved.

Trademark

The name of thi s product is the reg istered tradema rk of Samsung Techwin C o., Ltd.
Other trad emarks mention ed in this manual are th e registered trad emark of their resp ective company.

Restriction

Samsung Techwi n Co., Ltd shall reser ve the copyrigh t of this document. U nder no circumst ances, this docu ment shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwi n makes the best to ver ify the integri ty and correct ness of the conten ts in this document , but no
formal guar antee shall be provi ded. Use of this do cument and the subse quent results sha ll be entirely on the u ser’s own
responsib ility. Samsung Techwi n reserves the ri ght to change the con tents of this docum ent without prio r notice.

Warranty

If the produ ct does not opera te properly in norm al conditions, p lease let us know. S amsung Techwin will reso lve the
problem for f ree of charge. The wa rranty perio d is 3 years. However, the f ollowings are exclu ded:

• If the syste m behaves abnorma lly because you run a p rogram irreleva nt to the system oper ation.

• Deterior ated performan ce or natural worn -out in process o f time

Design and specifications are subject to change without prior notice.

is the regist ered logo of Samsun g Techwin Co., Ltd.

overview

important Safety inStructionS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for
long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

●

overview

English _3

overview

warninG

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.

caution

caution

riSK of eLectric SHocK.

Do not open

CAUTION

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

eXpLanation of GrapHicaL SymBoLS

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.

4_ overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.

CAUTION

These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not
be connected.

The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.

●

OVERVIEW

English _5

overview

Please read the following recommend safety precautions carefully.

yDo not place this apparatus on an uneven surface.
yDo not install on a surface where it is exposed to direct sunlight, near

heating equipment or heavy cold area.
yDo not place this apparatus near conductive material.
yDo not attempt to service this apparatus yourself.
yDo not place a glass of water on the product.
yDo not install near any magnetic sources.
yDo not block any ventilation openings.
yDo not place heavy items on the product.
yDo not expose the camera to radioactivity.

User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages
yNotice : If there’s any possibility to occur any damages for the goods and

human caused by not following the instruction



Please read this manual for the safety before using of goods and keep it in

the safe place.

6_ overview

contentS

oveRvIeW

3

InSTALLATIon &

ConneCTIon

13

opeRATIng YouR CAmeRA

O

2

AppenDIx

37

3 Important Safety Instructions
8 Product Features
9 What’s Included
10 At a Glance

13 Installation
16 Connecting with other Device

20 Menu Configuration
21 Menu Setup

37 Troubleshooting
38 Specification
39 Product Overview

●

overview

English _7

overview

PRODUCT FEATURES

• Supports Full HD-SDI Video

By adopting a diagonal 6mm (1/3”) 2M pixel CMOS, the camera produces clear picture

quality.

• Excellent low-illumination image quality

By adopting high-sensitive colour CMOS, the camera provides clear image quality under a

severe low illumination condition of 0.015 Lux (with SENS-UP, x60).

• SSNR3 (Samsung Super Noise Reduction) Function

The high-performance WN2 DSP chip effectively removes low-light gain noise and afterimage

to provide clear images even in dark environments.

•

Night (ICR)Day&

This camera has a function that automatically selects the mode that is appropriate for

daytime or night-time conditions. The COLOR mode operates in daytime conditions to

provide optimum colors, and B/W mode operates in night-time conditions to enhance the

definition of the image.

•

INTELLIGENCE

Once motion is detected, the camera sends an alert signal to the processing unit,

which, if used in conjunction with an optional alarm, can provide effective surveillance of

your property.

• SSDR (Samsung Super Dynamic Range)

For images with high contrast between bright and dark areas from difficult lighting conditions

such as backlighting, this camera selectively illuminates darker areas while retaining the same

light level for brighter areas to even out the overall brightness.

• Miscellaneous Functions

HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM and PRIVACY

functions are provided.

• OSD

By providing multi-lingual user-friendly OSD (On-screen Display) menu, the camera provides

easy handling of the camera.

8_ overview

wHat’S incLuDeD

Check if the main unit and all the following accessories are included in the product package.

Appearance

Item Name Quantity

Camera

1

Description

●

overview

Quick Manual

Cable for the testing monitor

L Wrench

Tapping Screw

Sunshield

Sunshield Hold

1

Used to test the camera connection to a

1

portable display device

1

Used to remove and replace the dome cover

Used for installation on the wall or ceiling

3

It protects the camera from the

1

1

It fixes the sunshield with the

direct sunlight.

camera.

English _9

overview

at a GLance

Appearance

Item Description

Sunshield It protects the camera from the direct sunlight.

a

Sunshield Hold It fixes the sunshield with the camera.

b

SETUP Switch

c

AF

$

T

W

_ +

%

N F

c

d

The switch is used for setting and adjusting the camera’s functions and properties.

N

/

F

/

W

T

Move this switch left or right to move the cursor or change
the value in the menu.
When menu is off, use this switch for adjusting focus.

Move this switch up or down to move the cursor in the menu.

When menu is off, use this switch for adjusting zoom.

VIDEO

d

10_ overview

Long to press this button to

@

Analogue video output terminal of Video. Use a monitor cable for testing the
camera with a portable display.

To move to a submenu item in the menu, press this switch.
Short to press this button to fit the focus automatically.

(for installation)

set the function in menu.

Components

a

CAUTION:

Rated Voltage and Polarity
of the power connection.

Be ware of the

b

c

d
e

Item Description

Power Port Used to plug the power cable.

a

Signal port for RS-485 communication.

Signal port for RS-485 communication.

Output port that signals when a motion is detected.

External signal input port for Day/Night mode setup.

Earth-grounding port for external signal.

I/O Port

b

HD-SDI Video Out

c

terminal

GREEN(485 –)

YELLOW(485+)

BLUE
(ALARM OUT)

GRAY(EXT_D/N IN)

BLACK(GND)

BNC terminal for HD-SDI video signal output.

●

overview

IR LED

d

Illumination Sensor

e

These infrared LED’s are controlled by the illumination sensor.

Detects incoming light to control the IR LED.

English _11

installation & connectioninstallation & connection

inStaLLation

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the



J

external cable is not. You are recommended to install this product below the edge of eaves to
prevent the cable from being externally exposed.

Installation

1. Fix the camera in 3 holes by tightening the

three tapping screws supplied with the
product.

2. Connect the cables with the camera port.

3. Adjust the direction of the camera with the

L-wrench supplied with the product.

connectinG witH otHer Device

CAUTION:

Be ware of the

HD-SDI Monitor

Motion detection output device

Day/Night mode controller

Rated Voltage and Polarity
of the power connection.

12_

installation & connection

Test monitor for

installation

Connecting to the monitor

Connect the video out port of the camera to the video input port of the monitor.

To check the display screen after installing the camera for the first time, you can use the Video

`

J

port to check the video screen.

You can set the video output type to either NTSC or PAL. (page 29).

`

The Video source (4:3) will be displayed with either side truncated in comparison with the

`

HD-SDI video.

The video source from the HD-SDI port can be displayed on the dedicated monitor. To display the

`

source on a commercial monitor, you need a converter to convert the video signal as appropriate.

Video Cable

The cable connecting the camera’s video output and a monitor is a BNC coaxial cable as
shown below.
If the distance between the camera and the monitor exceeds the recommended maximum,
please us an auxiliary video amp.

Maximum video transfer

distance

100~140m 5C2V(75ohm)

200m

Recommended cable

specification

L-6CHD(75ohm)

(SDI-specific Cable)

External Day/Night Switching Input

Day/Night mode of the camera can be switched by signal from an external device.

To use this function, <DAY/NIGHT> setting of the camera should be set to the <EXTERN>.

`

J

(Page 27)

●

inStaLLation & connection

Motion Detection Signal Out

Upon a motion detection, the port outputs signal for an external device for display or operation.
When a motion is detected, the port outputs 3.3V signal.

To use this function, <ALARM OUT> setting of the camera should be set to <ON>. (Page 31)

`

J

English _13

installation & connection

Power Supply

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.

Be careful not to reverse the polarity when you connect the power cable.

`

J

Be sure to turn the power off the device to be connected.

`

DVR

System Controller

or

T

+ T- R- R+

C

ONVERTER

R
S232C RS485, 422

RS-485
Converter

POWER

PC

CAUTION:

Rated Voltage and Polarity
of the power connection.

Be ware of the

For AC/DC Power Supply

You can use either one of AC 24V/1A~2A and DC 12V/2A~4A adaptor.

14_ installation & connection

Resistance of copper wire [at 20°C (68°F)]

Wire specification (AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2)

Resistance (Ω/m)

Voltage Drop (V/m)

Recommended Distance (m)

• As shown in the table above, you may encounter a voltage-sag depending on the
wire length. If you use an excessively long wire for camera connection, the camera
may not work properly.

Voltage for proper camera operation: DC 12V±10%, AC 24V±10%

`

Voltage drop shown in the table above may show difference from the actual depending on the

`

manufacturer and cable type.

RS-485 Communications

Using RS-485 communication, the camera menu can be accessed using Samsung
Techwin’s System Controller or the DVR.

• For accessing the camera from a computer
Use a RS-485 converter to connect the camera’s control port with the computer’s
serial cable.
Ex) Serial port (COM1) of computer  Serial Cable  RS-485 Converter  Camera’s

RS-485 control port

• For accessing the camera from a DVR or the System Controller
connect the camera’s RS-485+ and RS-485– terminals to the RS-485 control board’s
terminals of desired device with a RS-485 cable (TRX+ and TRX–).

Control ports of RS-485 Controller RS-485 ports of the camera

(+) CONNECTION TERMINAL (TRX+) 485+

(–) CONNECTION TERMINAL (TRX–) 485–

Default RS-485 communication settings

0.078 0.050 0.030 0.018

0.028 0.018 0.011 0.006

Less than 20 Less than 30 Less than 30 Less than 30

●

inStaLLation & connection

Item CAM ID BAUD RATE

Default 1 9600 8-N-1 DISABLE

When constructing a proprietary controller for direct camera control, apply Pelco-D or Samsung-

`

J

Techwin protocol.

Use only a DVR model that supports HD-SDI saving.

`

UART MODE

RET PKT

English _15

Operating Your Camera

menu confiGuration

MAIN SETUP

LENS •DC

EXPOSURE

WHITE BAL

SIMPLE FOCUS •

BACKLIGHT

SSNR3 •ON •OFF

DAY/NIGHT

SPECIAL

EXIT

•BRIGHTNESS •SHUTTER •AGC

➝

SET

•DEFOG •

MANUAL AWC

RESET RETURN

•SENS-UP

•RETURN

•ATW • •

• •

OUTDOOR INDOOR

FOCUSING

•OFF •BLC •HLC

•WDR

•AUTO •EXTERN •COLOR

•B/W

•CAM TITLE •IMAGE ADJ •INTELLIGENCE

•PRIVACY •PROFILE •COMM ADJ

LANGUAGE

• •

•

SSDR

➝

SET

16_ Operating Your Camera

menu Setup

Function Setup

switch

To configure the camera’s function settings, use the button on the rear side of the product.

AF

$

T

W

_ +

%

N F

:

Moves up/down in menu.

•$%

: Moves right/left in menu.

•_+

:

• Press the switch to set the function in camera menu.

@

To move to a sub-menu item in the menu, press this switch.

1. Press the SET button.

• Enters the function menu.
The selected function’s menu appears on the monitor.

MAIN SETUP

Use up/down buttons

to set the desired item.

►

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

4. FOCUSING

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

DC

Use right/left buttons
to change the

SET SIMPLE FOCUS

➝

selection.

8. SPECIAL

9. EXIT

● opeRATIng YouR CAmeRA

2. Use the Up/Down buttons to select a desired function.

• Move the button up or down to move the arrow up or down.
Set the arrow to indicate the desired item.

English _17

Operating Your Camera

3. Use the Up/Down buttons to select a desired function.

• Move the button right or left to display available values or settings.
Set the desired setting value using the button.

4. To finish, select <eXit> and press the SET button.

An item with the icon also has sub menus. To select a sub menu, select an item with the icon

`

M

press the Function Setup switch.

An item with the --- icon is unavailable due to function settings.

`

LenS

The lens type is fixedly DC.

• Dc : Auto Iris Lens.

eXpoSure

►

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

4.

SIMPLE FOCUS

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

8. SPECIAL

9. EXIT

MAIN SETUP

FOCUSING

DC

SET

➝

1. When the SETUP menu screen is displayed,
select <eXpoSure> by using the Function
Setup switch so that the arrow indicates
<eXpoSure> .

2. Select a desired mode using the Function
Setup switch.

• BriGHtneSS : Adjust the screen brightness.

18_ Operating Your Camera

MAIN SETUP

1. LENS

►

2. EXPOSURE

3. WHITE BAL ATW

SIMPLE FOCUS

4.

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

8. SPECIAL

9. EXIT

FOCUSING

DC

SET

➝

• SHutter : You can select the shutter.

- – – – :

Shutter speed is fixed.

- A.FLK : Select this when you experience
picture flicker, this happen when there is a
clash with the installed lighting frequency.

- ESC : Select this to control the shutter speed
automatically. If ESC is selected, the shutter

EXPOSURE SETUP

.... ....

.... ....

1. BRIGHTNESS

►

2. SHUTTER

3. AGC HIGH

4. SENS-UP AUTO
DEFOG ---

5.
SSDR ON

6.

7.

RETURN

50

*

ESC

speed is automatically controlled depending on
the ambient illumination of the subject.

- MANUAL : You can control shutter speed manually (1/30sec ~ 1/16,000sec)

When you use a DC lens, set the shutter mode to --- if color rolling occurs.

`

J

Carefully position the camera when installing, since produced image quality might be poor if

`

framing a bright light source while the shutter mode of EXPOSURE is set to AUTO.

When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.

`

• aGc(auto Gain controL) : The higher the gain level, the brighter the screen -
but the greater the noise.

- OFF : Not being used

- Low : Allows automatic gain control from 5.3dB to 20dB.

- Medium : Allows automatic gain control from 5.3dB to 26dB.

- High : Allows automatic gain control from 5.3dB to 32dB.

• SenS-up : When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.

- OFF : Deactivates the SENS-UP function.

- AUTO : Activates the SENS-UP function.

: Through the defogging function, camera can automatically recognize fog

• DefoG
concentration of the image, defog, self correct in hazy, rainy, flue gas and other

inclement weather to get a clear image.

: The camera will automatically correct

- AUTO

image according to the defogging level
(low, middle, high) set by the user.

- MANUAL

: The camera will adjust the definition

DEFOG SETUP

►

LEVEL MIDDLE
RETURN

of the image according to user's
preferences through the defogging
level (low, middle, high).

-

OFF : Turn off Defogging function.

opeRATIng YouR CAmeRA●

English _19

Operating Your Camera

•

SSDR( Samsung Super Dynamic Range)

image while retaining the same light level for brighter areas to even out the overall
brightness of images with high contrast between bright and dark areas.

:

- ON

Use the Function Setup switch to change the SSDR level in the sub menu according
to the contrast between bright and dark areas.

- OFF

: Turn off SSDR function.

: SSDR illuminates darker areas of an

:

SSDR ON

SSDR OFF

• return : Select this to save the changes in the EXPOSURE menu and return to
the MAIN SETUP menu.

Press the SET button while in AUTO mode to adjust the automatic scene accumulation multiplier

`

J

for low-illumination operation. (x2 ~ x60)

The greater the video accumulation factor is, the brighter the screen is but the afterimage of a

`

moving object grows accordingly.

Although noise, spots, and whitish symptoms may occur in higher accumulation, this is normal.

`

If the gain control (AGC) of EXPOSURE mode is set to OFF, SENS-UP mode is accordingly set to

`

‘- - -‘.

wHite BaL (wHite BaLance)

Use the White Balance function to adjust the screen color.

1. When the SETUP menu screen is displayed,
select <wHite BaL>. by using the Function
Setup switch so that the arrow indicates
<wHite BaL>.

2. Select a desired mode using the Function
Setup switch.

►

MAIN SETUP

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

4.

SIMPLE FOCUS

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

8. SPECIAL

9. EXIT

20_ Operating Your Camera

FOCUSING

DC

SET

➝

Select one of the following 5 modes, as appropriate for your purpose.

: Select this when the color temperature is between 2,400˚K and 11,000˚K.

• at w

• outDoor : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)

• inDoor : Select this when the color temperature is between 4,500˚K and 8,500˚K.

• manuaL : Select this to fine-tune White
Balance manually. Set White Balance first by
using the ATW or AWC mode. After that switch
to MANUAL mode, fine-tune the White Balance
and the Function Setup switch.

• awc

Set : To find the optimal luminance

➞

WHITE BAL MANUAL SETUP

►

RED
BLUE
RETURN

.... ....

.... ....

*
*

.... ....

.... ....

552
560

level for the current environment, point the
camera towards a sheet of white paper
and press the Function Setup switch. If the
environment changes, readjust it.

White Balance may not work properly under the following conditions. In this case select the AWC

`

J

mode.

When the ambient illumination of the subject is dim.

-

If the camera is directed towards a fluorescent light or is installed in a place where illumination

-

changes dramatically, the White Balance operation may become unstable.

● opeRATIng YouR CAmeRA

English _21

Operating Your Camera

SimpLe focuS

You can adjust the focus of video image.

1. When the SETUP menu screen is displayed,
select <

SIMPLE FOCUS

switch so that the arrow indicates

Setup
<

SIMPLE FOCUS

2.

Use the Function Setup switch to set up the

focus.

• focuSinG

automatically.

> by using the Function

>.

: Select this

Set

➝

to fit the focus

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

SIMPLE FOCUS

4.

►

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

8. SPECIAL

9. EXIT

MAIN SETUP

FOCUSING

DC

SET

➝

The focusing set mode may not fit correctly in the following cases:



J

➝

Sudden change to the object in Simple focus mode (sudden movement, appearance or

-

disappearance)
Radical change to the brightness in Simple focus mode

-

Image of a low contrast

-

-

If the camera is exposed to a strong light source in the front or surroundings

In a situation where Simple focus is hardly applied, try to use the manual focus mode.



BacKLiGHt

This camera is designed so that it delivers a distinctive subject and background at the
same time, even when the subject is in backlight, by adopting a function of the proprietary
WN2 DSP chip.

1.

When the SETUP menu screen is displayed, select < > by using the

Function Setup switch so that the arrow indicates

2.

Select a desired mode using the Function Setup switch depending on the camera

purpose.

• BLc

: Enables a user to select a desired area

on a picture and view that area more clearly.

- LEVEL : Adjust level of the BLC function.

- TOP/BOTTOM/LEFT/RIGHT

: Adjust the area

to be enhanced.

BacKLiGHt

<BacKLiGHt>.

BLC SETUP

►

1. LEVEL MIDDLE

2. TOP

3. BOTTOM

4. LEFT

5. RIGHT

6. RETURN

.... * .... .... ....

.... .... ....

.... * .... .... ....

.... .... ....

....

*

....

*

22_ Operating Your Camera

30
70
30
70

• HLC (High Light Compensation)
contains extremely bright light areas such as;
from car headlight, the light can mask out much

of the on-screen detail.

- LEVEL : Adjust level of the HLC function.

- MASK COLOR
masking area.

- MASK TONE

: Change the color of the

(Black, Red, Blue, Gray, Magenta)

: Change the brightness of the

: If the scene

►

1. LEVEL

2.

3.

4.

5.

6.

7.

8. RETURN

MASK COLOR
MASK TONE
TOP
BOTTOM
LEFT
RIGHT

HLC SETUP

.... ....

.... * .... .... ....

.... .... ....

.... * .... .... ....

.... .... ....

masking area.

- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.

• WDR

sharp image of the objects in a scene where
both bright and dark

Select a sensitivity level of WDR.

- LEVEL

:

• OFF : Not being used

Because there can be a difference in the effectiveness of HLC according to the amount of light

`

J

area in the screen, optimize the installation angle for the best HLC performance.

When dark, the HLC is only activated when a bright light exceeding a specific size.

`

The HLC is not activated in day light or when bright light is not present at night.

`

The CVBS don't output when the WDR function is used.

`

areas exist.

) (Wide Dynamic Range

:

It displays a

WDR SETUP MODE

►

LEVEL MIDDLE

RETURN

*

.... ....

*

*

....

....

MIDDLE

BLACK
7
30
75
30
75

● opeRATIng YouR CAmeRA

English _23

Operating Your Camera

SSnr3

This function reduces the background noise in a low luminance environment.

1. When the SETUP menu screen is displayed,
select <SSnr3> by using the Function Setup
switch so that the arrow indicates <SSnr3>.

2. Select a desired mode using the Function
Setup switch.

• on : Activates SSNR3 so that noise is reduced.

• off : Deactivates SSNR3. Noise is not
reduced.

3. Set the SSNR3 mode to <on> and press the
Function Setup switch. Then you can adjust the noise reduction level.

You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the ‘EXPOSURE’ menu is ‘OFF’.

`

J

When adjusting the noise reduction level in the SSNR3 mode, remember that the higher the level

`

set, the more the noise level will be reduced, as will the brightness of the image.

Day/niGHt

You can display pictures in color or in black and white.

1. When the SETUP menu screen is displayed,
select <Day/niGHt> by using the Function
Setup switch so that the arrow indicates <Day/

niGHt>.

2. Select a desired mode using the Function

Setup switch according to the picture display
you want.

• coLor : The picture is always displayed in
color.

• B/w : The picture is always displayed in black and white.

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

4.

SIMPLE FOCUS

5. BACKLIGHT OFF

6. SSNR3 ON

►

7. DAY/NIGHT AUTO

8. SPECIAL

9. EXIT

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

SIMPLE FOCUS

4.

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

►

8. SPECIAL

9. EXIT

MAIN SETUP

MAIN SETUP

FOCUSING

FOCUSING

DC

SET

➝

DC

SET

➝

24_ Operating Your Camera

• auto : The mode is switched to <coLor> in
a normal environment, but switches to <B/w>
mode when ambient illumination is low. To set
up the switching time for AUTO mode, press
the Function Setup switch.

- DWELL TIME : You can select day/night
switching delay time from.

➝

5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s

DAY/NIGHT AUTO SETUP

►

1. COLOR  B/W
DWELL TIME 5 SEC
DURATION FAST



2. B/W

COLOR
DWELL TIME 10 SEC
DURATION FAST

3.

DN FOCUS

4. RETURN

OFF

- DURATION : Adjust the brightness of the
lighting where the mode switch occurs.

- DN

➝

The video is automatically focused after the lighting mode changes

FOCUS :

from Day to Night or vice versa.

• eXtern : Control the image modes of Color and B/W when an external controller is
synchronized via the Alarm In port.

When AGC in the EXPOSURE menu is ‘OFF’, AUTO mode is not available to select.

`

J

SpeciaL

● opeRATIng YouR CAmeRA

1. When the SETUP menu screen is displayed,
select <SpeciaL> by using the Function Setup
switch so that the arrow indicates <SpeciaL>.

2. Select a desired mode using the Function
Setup switch.

MAIN SETUP

1. LENS

2. EXPOSURE

3. WHITE BAL ATW

4.

SIMPLE FOCUS

5. BACKLIGHT OFF

6. SSNR3 ON

7. DAY/NIGHT AUTO

8. SPECIAL

►

9. EXIT

SPECIAL SETUP

►

1. CAM TITLE OFF

2. IMAGE ADJ

3. INTELLIGENCE OFF

4. PRIVACY

5.

PROFILE

6.

7.

8.

9.

COMM ADJ
LANGUAGE ENGLISH
RESET
RETURN

FOCUSING

➝

BASIC

DC

SET

English _25

Operating Your Camera

• CAM TITLE : If you enter a title, the title will
appear on the monitor.

1) If the SPECIAL menu screen is displayed, use

the Function Setup switch so that the arrow
indicates <CAM TITLE>.

2) Set it to <ON> by using the Function Setup

switch.

3) Press the Function Setup switch.

4) Use the Function Setup switch to move to a

desired letter and select the letter by pressing the Function Setup switch. Repeat this
to enter multiple letters. You can enter up to 15 letters.

5) Enter a title, move the cursor to <POS>

and press the Function Setup switch. The
entered title appears on the screen. Select
the position to display the title on the screen
by using the Function Setup switch and press
the Function Setup switch. When the position
is determined, select <END> and press
the Function Setup switch to return to the
SPECIAL menu.

When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you

`

J

enter one.

Alphanumeric charaters are all available in this mode.

`

If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted.

`

To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch.
Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then
press the Function Setup switch.

CAMERA TITLE SETUP

A BCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
–.123456789

←→

CLR POS END

— — — — — — — — — — — — — —

ABCD

←→↑↓

to Locate, then SET

26_ Operating Your Camera

• imaGe aDJ :

1) When the SPECIAL menu screen is displayed,
select <imaGe aDJ> by using the Function
Setup switch so that the arrow indicates
<imaGe aDJ>.

►

SPECIAL SETUP

1. CAM TITLE OFF

2. IMAGE ADJ

3. INTELLIGENCE OFF

4. PRIVACY

5.

PROFILE

6.

7.

8.

9.

COMM ADJ
LANGUAGE ENGLISH
RESET
RETURN

BASIC

2) Select a desired mode using the Function Setup switch.

- MONITOR : Please change the settings value
of video appropriate to your monitor.

• LCD : Please select this menu item when
using an LCD monitor.

• USER : Please use this menu item when
using a monitor other than standard ones.

You can change the gamma, and

color level

reset in the sub menus.

►

IMAGE SETUP

MONTIOR LCD

1.

2. H-REV OFF

3. V-REV OFF

4. D-ZOOM OFF

5.

DIS OFF

6.

SHARPNESS ON

7.

OSD COLOR WHITE

8.

VIDEO OUT FORMAT

9. RETURN

- H-REV : You can flip the picture horizontally on
the screen.

- V-REV : You can flip the picture vertically on the screen.

- D-ZOOM : You can use a digital zoom of x2 ~ x16.

: Compensates the image automatically when it is seen to shake for stable

- DIS

image output.

- SHARPNESS : As you increase this value, the picture outline becomes stronger and
clearer. Adjust this value appropriately depending on the sharpness of the picture.

- OSD COLOR :

- VIDEO OUT FORMAT

VIDEO SIZE

•

You can change the OSD font color. (White, Yellow, Green, Red, Blue)

: Sets the video size and video fmt.

: Sets the image resolution of the HD-SDI output of the camera.
Select the desired setting and press the SET button. (NTSC : 1080i 60, 1080p 30,
720p 60 ; PAL : 1080i 50, 1080p 25, 720p 50)

VIDEO FMT

•
for test and installation.(NTSC, PAL)

: Sets the video output format of the Video port on the camera provided

- RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to
the SPECIAL menu.

● opeRATIng YouR CAmeRA

If you increase the sharpness level excessively, the image may be displayed abnormally or it can

`

J

cause a noise.

English _27

Operating Your Camera

• inteLLiGence :

motion-detect and trace an object.

DETECTION : Since the camera detects

­motion without any additional external sensor,
you can monitor activity more effcient.

TRACKING : Commands the camera to detect

-

and trace a moving object.

▶

TYPE : Two types, line and area, of fences
are available.

▶

COUNT : Displays the number of times
that an object enters or leaves a fenced area.

▶

DISPLAY : Determines whether to use the

Commands the camera to

INTELLIGENCE

►

1. DETECTION

2. TRACKING OFF

3. FIXED/MOVED OFF

4. TAMPERING

5. DETECT BOX

6. ALARM OUT

7. SETUP CONFIG

8.

RETURN

TRACKING

►

1. TYPE

2. COUNT OFF

3. DISPLAY ON

4. FILL

5. POSITION

6.

RETURN

fence selected in the FENCE.

▶

FILL : Fill or remove color from the FENCE.

▶

POSITION : Defines the position and detection direction of a line or fenced area.

1) LINE FENCE

- SEL POS : Selects a position from POS1,POS2.

- X POS / Y POS : Adjust the size and position of the selected line fence.

- DIRECTION

·

DIR1 : Detects objects moving right to left on the fence line.
DIR2 : Detects objects moving left to right on the fence line.

·

DIR1/2 : Detects all objects moving crosswise on the fence line.

·

-

RETURN : Select this to save the POSITION menu settings and return to the
TRACKING menu.

2) AREA FENCE

- SEL POS : Selects a position from POS1 ~ POS4.

- X POS / Y POS : Adjust the size and position of the selected area fence.

- DIRECTION
IN : Detects objects entering the fenced area.

·

OUT : Detects objects exiting the fenced area

·

IN/OUT : Detects all objects entering and exiting the fenced area.

·

- RETURN : Select this to save the POSITION menu settings and return to the
TRACKING menu.

▶

RETURN : Select this to save the TRACKING menu settings and return to the
INTELLIGENCE menu.

OFF

OFF
OFF
OFF

LINE

OFF

28_ Operating Your Camera

TRACKING

►

-

FIXED/MOVED : Detects an object that emerges or disappears from the screen, or

POS1

SEL POS
X POS
Y POS
DIRECTION DIR1

RETURN

.... .. .. .... ....

*

.... .... .... ....

*

stays onscreen without movement

A detection (FIXED/MOVED) error may occur if :

`

J

· multiple motions occur continuously in random directions

►

106

12

.

TRACKING

SEL POS

POS1

.... .. .. .... ....

X POS
Y POS
DIRECTION IN

RETURN

*

.... .... .... ....

*

106

12

· a fixed object moves in one position continuously

a second object screens the first moving object

·

-

TAMPERING

:

You can set to detect tampering attempts and trigger events, such

as blocked lens.

-

DETECT BOX : Outlines an object on the screen in a box when its movement
matches a custom Motion Type.

-

ALARM OUT : Releases a signal from the MD Output Terminal of the camera
when an object’s movement matches a custom Motion Type.

-

SETUP CONFIG :

▶

DETECT AREA : Defines the Motion

Detection area.

AREA SEL: You can select up to 4 areas.

·

MODE : Determines whether to use the

·

area selected in the AREA.

·

DETECT ALARM : Determines whether

SETUP CONFIG

►

1.

DETECT AREA

2. SENSITIVITY 3

3. DET.SIZE
RETURN

4.

to use the detect alarm selected in the
AREA.

·

TOP / BOTTOM / LEFT / RIGHT : Adjust

the size and position of the selected area.

·

RETURN : Select this to save the

DETECT

AREA menu settings and return to the

SETUP CONFIG menu.

DETECT AREA

►

AREA SEL
MODE
DETECT ALARM
TOP
BOTTOM
LEFT
RIGHT
RETURN

.... .... .... ....

*

.... .... .... ....

*

AREA 1

.... .... .... ....

.... .... .... ....

● opeRATIng YouR CAmeRA

3

OFF
OFF

32

*

1048

32

*

1088

English _29

Operating Your Camera

▶

SENSITIVITY : Set the sensitivity of the motion detection. When adjusting the

sensitivity, note that the lower the level means the higher sensitivity.

▶

DET. SIZE : Selects an object size to detect on the screen. When adjusting the

detection size, note that the higher the level means the bigger detection size.

▶

RETURN : Select this to save the SETUP CONFIG menu settings and return to
the INTELLIGENCE menu.

-

RETURN : Select this to save the INTELLIGENCE menu settings and return to the
SPECIAL menu.

You can specify a certain area of the

• privacy

camera video to be protected for your privacy.

:

1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the
arrow indicates <privacy>.

2) Set up the mode using the Function Setup
switch.

- (

TYPE 1 , In this type the shape of selected

area is rectangular

▶

AREA SEL: Y ou can select up to 16 PRIVACY

areas.

▶

AREA MODE : Determines whether to use
the area selected in the AREA SEL.

MASK COLOR

▶

)

: Determine area color. You can

select Green, Red, Blue, Black, White, Gray.

▶

TOP / BOTTOM / LEFT / RIGHT :

Adjust the

size and position of the selected area.

▶

- ( , In this type the shape of selected

TYPE

area is polygonal

▶

▶

▶

: Select this to save the TYPE 1

RETURN

menu settings and return to the PRIVACY menu.

2

)

AREA SEL: Y ou can select up to 4 PRIVACY

areas.

AREA MODE : Determines whether to use
the area selected in the AREA SEL.

MASK COLOR

: Determine area color. You can

select Green, Red, Blue, Black, White, Gray.

▶

SEL POS/XPOS/YPOS : Adjust the size and
position of the selected area.

►

TYPE 1

1.

2. OFF

TYPE 2

3.

RETURN

►

AREA SEL

1. AREA1

2. AREA MODE OFF

3. MASK COLOR GRAY

4. TOP

5. BOTTOM

6. LEFT

7. RIGHT

8. RETURN

►

1. AREA1

AREA SEL

2. AREA MODE OFF

3. MASK COLOR GRAY

4. SEL POS

5.

X POS
Y POS

6. 10

7.

RETURN

PRIVACY

TYPE 1

TYPE 2

.... .... .... ....

*

.... * .... .... ....

... . .... .... ....

*

.... * .... .... ....

.... * .... .... ....

.... .... .... ....

*

OFF

23
59
35
67

L TOP

­ 30

30_ Operating Your Camera

▶

RETURN

: Select this to save the TYPE 2

menu settings and return to the

PRIVACY menu.

- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL
menu.

pROfIle

: S elect a desired mode using the Function

Setup switch according to the picture display you

want.

-

BASIC : The most common environment is set

to meet.

-

DAY/NIGHT : It will be set automatically so it

►

optimizes to the day or night conditions,
respectively.

-

BACKLIGHT

you can distinguish the object from the background in a severe backlighting scene.

-

ITS : It will be set automatically so you can easily check the traffc conditions.

-

INDOOR : It will be set automatically to help you take a picture in a regular indoor

It will be set automatically so

:

SPECIAL SETUP

1. CAM TITLE OFF

2. IMAGE ADJ

3. INTELLIGENCE OFF

4. PRIVACY

5.

PROFILE

6.

7.

8.

9.

COMM ADJ
LANGUAGE ENGLISH
RESET
RETURN

BASIC

lighting condition.

-

USER : Automatically configures the camera to your custom settings.

Select Custom for Simple Setup mode.

1)

Configure the menu options to your custom settings.

2)

The settings are automatically saved as Custom mode.

3)

Profile user mode don't initialize when menu resets.

4)

-

BANK : The system will automatically set if dark and bright area are all exist at

same time, sothat you can recognize the object in bank easily.

I

n the PROFILE menu, you can configure the following camera settings at

*

once.

● opeRATIng YouR CAmeRA

BASIC DAY/NIGHT

SHUTTER ESC ESC ESC

AGC

HIGH HIGH HIGH HIGH HIGH -

BACKLIGHT ITS INDOOR USER

ANUAL(1/250)

M

.FLK -

A

WHITE BAL ATW ATW ATW OUTDOOR INDOOR -

BACKLIGHT OFF OFF OFF OFF -

BLC

SSNR3 ON ON ON ON ON -

DAY/NIGHT AUTO AUTO AUTO AUTO AUTO -

BANK

---

HIGH

ATW

WDR

ON

AUTO

English _31

Operating Your Camera

• COMM ADJ (Communication Adjustment) :
This function sets up the camera
communication status when controlling the
camera through an external control device.

1) When the SPECIAL menu screen is displayed,

press the Function Setup switch so that the
arrow indicates <COMM ADJ>.

COMMUNICATION SETUP

►

1. PROTOCOL SAMSUNG-T

2. CAM ID

3. BAUD RATE 9600

4. UART MODE 8-N-1

5. DISP ID OFF

6. RET PKT ENABLE

7. RETURN

.... .... .... ....

*

2) Set up the mode using the Function Setup

switch.

- PROTOCOL : Select the communication PROTOCOL. (SAMSUNG-T, SAMSUNG-E,
Pelco-D, Pelco-P, Bosch, Honeywell, Vicon, Panasonic, GE, AD)

- CAM ID : Determines the camera's identification number (between 0 and 255).

- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.

- UART MODE : You can select NONE, EVEN or ODD for the parity bits.

- DISP ID : Display camera title on top left corner of the screen.

- RET PKT : Specify whether to return the same command to the controlling device when
a control command is delivered to the camera.

When protocol such as SAMSUNG-T,SAMSUNG-E,Pelco-D&Pelco-P are in using, you can use

`

J

preset95 command to activate Menu.

• LANGUAGE : You can select the menu language according to your requirements.

• RESET : Resets the camera settings to the factory defaults. Communication,
Language, Video Format and Monitor settings are not initialized.

• RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.

EXIT

Save the current settings and exit the MAIN SETUP menu.

1

32_ Operating Your Camera

appendix

trouBLeSHootinG

PROBLEM SOLUTION

Nothing appears on the screen.

The image on the screen is dim.

The image on the screen is dark.

The camera is not working
properly, and the surface of the
camera is hot.

The SENS-UP function does not
work.

The Motion Detection function
does not work.

Color is not correct.

The screen flickers continually.

RS-485 communication is not
available.

yCheck that the power cord and line connection between the camera and

monitor are properly connected.

yWhen the camera’s HD-SDI BNC output is directly connected to the

monitor’s BNC terminal:
Make sure the monitor supports HD-SDI signal input.

yWhen the camera’s HD-SDI BNC output is connected to the DVR: Make

sure the DVR supports HD-SDI signal input.

yHD-SDI output is converted into other format such as DVI and VGA by

using video converter: Make sure the converter’s HD-SDI input format
supports the product’s output video format.

yIs lens stained with dirt? Clean your lens with soft, clean cloth.

ySet the monitor to the proper condition.

yIf the camera is exposed to very strong light, change the camera position.

yAdjust the contrast feature of the monitor.

yCheck that you have properly connected the camera to an appropriate

power source.

yCheck that AGC of EXPOSURE SETUP menu is ‘OFF’.

yCheck that MOTION DET of SPECIAL SETUP menu is ‘OFF’.

yCheck the setting of WHITE BAL SETUP menu .

yEnsure the camera is not pointing towards the sun.

yIs the camera framing the sun or other bright light source?

yHD-SDI video may not appear to be normal if distance exceeds the

maximum transferrable distance.

yWhen a BNC cable adaptor is used to combine two or more BNC cables

for distributed HD-SDI video transfer, make sure the impedance of the
adaptor is 75Ω. Otherwise, it may cause shorter transfer distance or
broken video transfer.

yCheck RS-485 communication settings.

● AppenDIx

English _33

appendix

Specification

Items Description

Video 1/3" Progressive Scan CMOS

Total Pixels 2,010(H) x 1,108(V), 2.2M Pixels

Effective Pixels 1,944(H) x 1,092(V), 2.1M Pixels

Video

Lens Type

Operational

Scanning System Progressiv Scan

Min. Illumination

S / N Ratio 50dB (AGC off, Weight on)

Video Output SMPTE292M ( HD-SDI ), Monitoring CVBS

Lens Type

Mount Type

On Screen Display

Camera Title Off / On (Displayed 15 characters)

Day & Night Auto (ICR), Color, B/W , External

Backlight Compensation

Contrast Enhancement SSDR ( Off / On )

Digital Noise Reduction SSNR

Intelligent Video

IR Distance 30m (IR LED,20 ea)

Color : 1Lux @ F1.2, 0.015 Lux (Sens-up, x60)

B/W : 0 Lux ( IR LED,ON )

DC Auto Iris Lens (3~8.5mm (2.8X) Motorized Vari-focal)

Board type

Multi-language Support
English, Korean, Japanese, Spanish, French, Portuguese, Chinese,
German, Italian, Russian, Czech, Polish, Rumanian, Serbian, Swedish,
Denish, Turkish

Off / BLC / HLC / WDR

Ⅲ

( Off / On )

Tampering, Detection,Tracking,Fixed/Moved

34_ appendix

Items Description

Privacy Masking Off / On (4 Polygonal + 16 Rectangular zones)

Sens-up (Frame
Integration)

Gain Control Off / Low / Middle / High

White Balance

Operational

Environmenta

Electrical

Mechanica Dimension(WxHxD)

HD-SDI
Transmission
Distance

`

`

`

※

For enhanced performance, the product specification is subject to change without prior notice.

Electronic Shutter
Speed

Digital Zoom Off / On (x2 ~ x16)

Reverse

Communication RS-485

Protocol

Operating Temperature
/ Humidity

Input Voltage Dual ( 24VAC±10% & 12VDC±10% )

Current

Weight

5C2V ( 75 ohm ) Max. 100~140m

L-6CHD ( 75 ohm ) Max. 200m

The maximum transferrable distance of HD-SDI video signal depends on the cable manufacturer or installation
conditions.
When a BNC cable adaptor is used to combine two or more BNC cables for distributed HD-SDI video transfer,
make sure the impedance of the adaptor is 75Ω. Otherwise, the adaptor may cause shorter transfer distance or
broken video transfer due to loss of transferred signal.
If you intend to install the product outdoors, you must use the housing to meet the temperature/humidity
conditions as specified above. In particular, if the product is installed in a place where the temperature falls
below zero (0) degree, it is recommended to install a separate heater inside of the housing in an attempt to
meet the operating conditions.

Off / Auto (x2 ~ x60)

(1,700K° ~ 11,000K°)

SET

ATW / Outdoor / Indoor / Manual / AWC

Esc / A.FLK / Manual / ---

Off / H-Rev / V-Rev

RS-485 : SAMSUNG-T, SAMSUNG-E, Pelco-D, Pelco-P, Bosch,
Honeywell, Vicon, Panasonic, GE, AD

-10°C~+55°C (14°F~131°F) / ~90% RH

0.47A

82.2 x 85 x 175mm (WITHOUT BRACKET), 90 x 90 x 312.6mm (WITH BRACKET)

1020g

➝

● AppenDIx

English _35

appendix

proDuct overview

90.4 (3.56")

Unit : mm (inch)

96.8 (3.81")

36_ appendix

200 (7.87")

178 (7.01")

82.2

90.4 (3.56")

333.2 (13.12")

321.6 (12.31")

Ø 82 (3.23")
(BODY)

3- Ø 5.5 HOLES

120°

90 (3.54")

134.6 (5.30")

Ø 70 (2.76")

120°

SALES NETWORK

SAMSUNG TECHWIN CO., LTD.

Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : [phone]~60 FAX : [phone]

SAMSUNG TECHWIN AMERICA Inc.

100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : [phone] Direct : [phone]
Fax : [phone]
www.samsungcctvusa.com

www.samsungtechwin.com
www.samsungsecurity.com

SAMSUNG TECHWIN EUROPE LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : [phone] FAX : [phone]

PT01-001891A