samsung SC-D103 Service Manual

Samsung Electronics 1-1
1. Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including : control knobs and compartment covers.
--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.
If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.
4. Leakage Current Hot Check (See Fig. 1-1) : Warning : Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug the AC line cord directly the power outlet. With the unit’s AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including : antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed
0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.
6. X-ray Limits : The picture tube is designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original.
Fig. 1-1 AC Leakage Test
7. Antenna Cold Check : With the unit’s AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.
8. High Voltage Limit : High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits.
Heed the high voltage limits. These include the X-ray protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
9. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.
10. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.)
DEVICE UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
LEAKAGE CURRENT
TESTER
EARTH
GROUND
TEST ALL
EXPOSED METER
SURFACES
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
2-WIRE CORD
Precautions
1-2 Samsung Electronics
11. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.
12. Design Alteration Warning : Never alter or add to the mechanical or electrical design of this unit. Example : Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.
13. Hot Chassis Warning : Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source.
To confirm that the AC power plug is inserted correctly, do the following : Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground.
14. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.
15. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.
16. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.
17. Observe the original lead dress, especially near the following areas : Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out­of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.
18. Picture Tube Implosion Warning : The picture tube in this receiver employs “integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.
19. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.
20. Product Safety Notice : Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc.
Components that are critical for safety are indicated in the circuit diagram by shading, ( or ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. Areplacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
Samsung Electronics 3-1
3. Exploded View and Parts List
3-1 Ass’y Chassis - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2 3-2 Ass’y EVF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-4 3-3 Ass’y Left - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6 3-4 Ass’y Right - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-8 3-5 Ass’y LCD- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-10 3-6 Ass’y Top - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-12 3-7 Ass’y Front - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-14 3-8 Ass’y Rear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-16 3-9 Ass’y Cover Housing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-17 3-10 Mechanical Parts (Main Chassis) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-18 3-11 Mechanical Parts (Sub Chassis) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-20
Page
You can search for the updated part code through ITSELF web site. URL; http://itself.sec.samsung.co.kr
Notice
Exploded View and Parts List
3-2 Samsung Electronics
3-1 Ass’y Chassis
150
180
903
917
170
171
173
165
917
160
917
166
Exploded View and Parts List
3-3Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
150 AD97-07910A ASSY-DECK;-,DD-4,ASSY 160 AD97-08324A ASSY-LENS-ZOOM;PC,SHML,20X 165 AD61-01592A BRACKET-LENS A;DELTA2,SUS304 1/2H,T0.5,W 166 AD61-01593A BRACKET-LENS B;DELTA2,SUS304 1/2H,T0.5,W 170 AD97-08367A ASSY-CCD BORAD;DELTA2-PJ,SC-D103,CCD BOR 171 AD60-00053A SPACER-CCD;ALPHA_PJ,SILICON,-,-,-,BLK,0. 173 AD67-00253A LENS FILTER-OLPF;SHML,ºˆ¡§ ∫π±º¿˝«,WHIT 180 AD97-08405A ASSY-MAIN;DELTA2-PJ,SC-D103,MAIN 903 6001-000805 SCREW-MACHINE;CH,+,M1.7,L3,NI PLT,SWRCH1 917 6003-001453 SCREW-TAPTITE;BH,+,B,M1.7,L4,ZPC(BLK)
Exploded View and Parts List
3-4 Samsung Electronics
3-2 Ass’y EVF
422
711
703
912
702
901
715
717
713
720
913
919
730
714
701
901
901
935
936
423
Exploded View and Parts List
3-5Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
422 AD41-00525A FPC-EVF;DELTA2-PJ,-,POLYMIDE,-,0.15(0. 423 AD97-07913A ASSY-UNIT-EVF;0.24NTSC,DELTA/THETA/OMEG 701 AD61-12033A BRACKET-NUT;SV-D10,T0.8,-,-,-,-,T0.8 702 AD61-01596A CASE-EVF BOTTOM;DELTA2-PJ,ABS 94V0,T34,W 703 AD69-00461A PAD-EVF;DELTA-PJ,∆˜∑–,0.5,20.5,7,-,BLA 711 AD61-01597A CASE-EVF TOP;DELTA2-PJ,ABS 94V0,T34,W24, 713 AD73-00118A RUBBER-EYE CUP;DELTA2-PJ,TPU,36X24X10.2, 714 AD61-01613A GUIDE-LINK;DELTA2-PJ,PC,T34,W24,L36,SILV 715 AD61-01610A HOLDER-LENS CVF;DELTA2-PJ,ABS 94 HB,T7.8 717 AD67-00194A LENS-EVF 14X G1;DELTA-PJ,OPT PLASTIC PMM 720 AD64-01165A KNOB-EVF;DELTA2-PJ,POM,T4.5,W3.6,L5,-,B 730 AD97-08463A ASSY-EVF LINK;-,DELTA2-PJ,EVF LINK 901 6001-000805 SCREW-MACHINE;CH,+,M1.7,L3,NI PLT,SWRCH1 912 6002-001132 SCREW-TAPPING;BH,T0.5,+,2,M1.7,L3.0,BLK, 913 6002-001085 SCREW-TAPPING;CH,+,2,M1.7,L5,ZPC(BLK),SW 919 6009-001325 SCREW-SPECIAL;CH,+,,M1.4,L5(1.9),ZPC(BLK 935 AD97-06506A ASSY-EVF BOARD;DVC,SC-D23,EVF BOARD 936 AD07-00009A LCD-PANNEL;MCVVQ410(320),VP-D50,320*240,
Exploded View and Parts List
3-6 Samsung Electronics
3-3 Ass’y Left
520
916
916
535
530
511
536
541
543
542
540
560
570
514
517
911
911
917
917
917
580
913
512
911
600
Exploded View and Parts List
3-7Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
511 AD64-01148A BUTTON-FUNCTION 2.5;DELTA2,ABS 94HB,75. 512 AD61-01582A BASE-TRI POD;DELTA2,PC,T10.3,W32,L20.3,L 514 AD61-01595A BRACKET-SPEAKER;DELTA2,SUS304 1/2H,T0.5, 517 AD61-01594A BRACKET-SHOULDER STRAP;DELTA2,SUS304 1/2 520 AD97-08465A ASSY-COVER LEFT;-,DELTA2-PJ,NTSC,EXP,MS( 530 AD97-08461A ASSY-UNIT CASE LEFT2.5;-,DELTA2-PJ,SCD10 535 AD64-01159A KNOB-SELECT;DELTA2-PJ,ABS 94HB,T4,W9.45, 536 AD61-01621A HOLDER-SELECT;DELTA2-PJ,POM,T6,W9,L25.3, 540 AD97-08466A ASSY-MS DOOR;-,DELTA2-PJ,NTSC,EXP,MS(O) 541 AD63-00555A COVER-DOOR M/S;DELTA2-PJ,ABS 94HB,T1.4,W 542 AD61-01615A HOLDER-DOOR M/S;DELTA2-PJ,ABS 94HB,T6.9, 543 AD61-01028A SPRING ETC-DOOR M/S;BETA-PJ,SUS304 WPB,­560 AD97-08377A ASSY-SPEAKER;DELTA2-PJ,SC-D103,SPEAKER 570 AD97-08407A ASSY-LEFT BOARD;DELTA2-PJ,SC-D103,LEFT B 580 AD97-08410A ASSY-FUNCTION BOARD;DELTA2-PJ,SC-D103,FU 600 AD97-08445A ASSY-LCD;-,DELTA2-PJ,NTSC, SCD103 911 6002-001085 SCREW-TAPPING;CH,+,2,M1.7,L5,ZPC(BLK),SW 913 6003-001142 SCREW-TAPTITE;CH,+,B,M1.7,L5,NI PLT,SRWC 916 6003-001445 SCREW-TAPTITE;PH,+,B,M2,L5,ZPC(BLK) 917 6003-001453 SCREW-TAPTITE;BH,+,B,M1.7,L4,ZPC(BLK)
Exploded View and Parts List
3-8 Samsung Electronics
3-4 Ass’y Right
440
918
906
444
918
442
430
901
901
434
433
901
431
918
462
454
462
901
451
420
901
422
421
918
461
455
460
906
457
453
458
452
459
127
470
128
410
456
Exploded View and Parts List
3-9Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
127 AD63-00571A COVER-ADJUST;DELTA2-PJ,ABS 94HB,T1.5,W7. 128 AD63-00559A COVER-LI BATTERY;DELTA2-PJ,ABS 94HB,T8.3 410 AD97-08462A ASSY-LINK;-,DELTA2-PJ,HOUSING LINK 420 AD97-08369A ASSY-POWER;DELTA2-PJ,SC-D103,POWER 421 AD61-01587A BRACKET-POWER PCB;DELTA2,SECC,T0.5,W11,L 422 AD97-08370A ASSY-START/STOP BOARD;DELTA2-PJ,SC-D103, 430 AD97-08376A ASSY-JACK;DELTA2-PJ,SC-D103,JACK 431 AD97-08371C ASSY-JACK BOARD;DELTA2-PJ,SC-D103,JACK B 433 AD61-01583A BRACKET-JACK;DELTA2,SUS304 1/2H,T0.5,W46 434 AD97-08409A ASSY-LITHIUM BOARD;DELTA2-PJ,SC-D103,LIT 440 AD97-08459A ASSY-CASE RIGHT;-,DELTA2-PJ,EXP,USB(O) 442 AD61-12033A BRACKET-NUT;SV-D10,T0.8,-,-,-,-,T0.8 444 AD73-00006A RUBBER—GUIDE DECK;BUTHYL RUB,-,VP-D50,­451 AD63-00561A COVER-RIGHT;DELTA2-PJ,ABS 94HB,T50,W68.7 452 AD61-01169A SPRING ETC-PLATE RECORD;DELTA-PJ,SUS ,-, 453 AD61-60521A SPRING-REC;SC-80,SWPB,4.3,-,-,-,-,-,-,-, 454 AD61-01585A BRACKET-RIGHT;DELTA2,SUS304 1/2H,T0.5,W1 455 AD61-60601A SPRING-KNOB POWER;-,SUS304 WPB,-,-,-,-,­456 AD63-00565A COVER-JACK;DELTA2-PJ,ABS+URETAN,T16,W28, 457 AD64-00936A BUTTON-POWER RECORD;DELTA-PJ,ABS 94HB,-, 458 AD64-00942A KNOB-POWER;DELTA-PJ,ABS 94HB,-,-,-,-,BLK 459 AD61-01146A PLATE-POWER;DELTA-PJ,SUS T0.5,T0.2,-,-,N 460 AD64-00947A LOCKER-SAFETY POWER;DELTA-PJ,ABS 94HB,-, 461 AD66-00278A SLIDER-POWER;DELTA2-PJ,POM,T5.8,W14,L15, 462 AD73-00006A RUBBER—GUIDE DECK;BUTHYL RUB,-,VP-D50,­470 AD97-08448A ASSY-BELT GRIP;LEATHER,DELTA2-PJ,­901 6001-000805 SCREW-MACHINE;CH,+,M1.7,L3,NI PLT,SWRCH1 906 6001-001527 SCREW-MACHINE;CH(0.3),+,M1.7,L2.0,NI PLT 918 6003-001490 SCREW-TAPTITE;PH,+,B,M1.7,L4,NI PLT,SWCH
Exploded View and Parts List
3-10 Samsung Electronics
3-5 Ass’y LCD
611
618
614
620
908
912917
904
917
604
613
904
601
630
634
636
631
637
632
633
603
619
Exploded View and Parts List
3-11Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
601 AD97-08372A ASSY-LCD BOARD(2.5);DELTA2-PJ,SC-D103,LC 603 AD07-00039A LCD;PA025XS8,DELTA-PJ,480*234,61.6 604 AD97-08470A ASSY-BACK LIGHT2.5;-,DELTA2-PJ,2.5 611 AD63-00563A COVER-HINGE BOTTOM 2.5;DELTA2-PJ,ABS 94 612 AD63-00562A COVER-HINGE TOP 2.5;DELTA2-PJ,ABS 94V0, 613 AD62-00027A INSULATION-BACK LIGHT;BETA-PJ,PVC,T0.05, 614 AD61-12033A BRACKET-NUT;SV-D10,T0.8,-,-,-,-,T0.8 618 AD61-01603A CASE-LCD BOTTOM 2.5;DELTA2-PJ,ABS 94V0, 619 AD97-08469A ASSY-HINGE;-,DELTA2-PJ,HINGE 620 AD97-06489A ASSY-LCD FPC;.,DELTA-PJ,LCD FPC 630 AD97-08439A ASSY-CASE LCD TOP2.5;-,DELTA2-PJ,NTSC, 631 AD61-01602A CASE-LCD TOP 2.5;DELTA2-PJ,ABS 94V0,T7. 632 AD64-01161A LOCKER-LCD;DELTA2-PJ,POM,WHT,-,-,9.6X5.6 633 AD61-01606A HOLDER-LOCK LCD;DELTA2-PJ,ABS 94HB,T1,W7 634 AD61-01624A SPRING ETC-LOCK LCD;DELTA2-PJ,SUS304 WPB 636 AD64-01171A INLAY-MS;DELTA2-PJ,PC,T0.6,W15,L15,BLUE 637 AD64-00808A BADGE-SAMSUNG;P[ 904 6001-001444 SCREW-MACHINE;PH,+,M1.7,L2.0,ZPC(BLK),SW 908 6001-001716 SCREW-MACHINE;BH,+,M2,L4,NI PLT 917 6003-001453 SCREW-TAPTITE;BH,+,B,M1.7,L4,ZPC(BLK) 937 AD64-00808A BADGE-SAMSUNG;ALPHA_PJ,AL,T0.7,-,-,-,SIL
Exploded View and Parts List
3-12 Samsung Electronics
3-6 Ass’y Top
120
122
123 124
915
808
811
812
442
801
442
442
803
805
804
807
809
911
Exploded View and Parts List
3-13Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
120 AD97-08444A ASSY-GRILL MIC;-,DELTA2-PJ,NITE PIX(O) 122 AD64-01153A GRILLE-MIC A;DELTA2-PJ,ABS 94HB,T8.4,W26 123 AD64-01158A KNOB-NITE PIX;DELTA2-PJ,ABS 94HB,T12.6,W 124 AD61-01619A HOLDER-NITE PIX;DELTA2-PJ,POM,T4.8,W10.5 442 AD61-12033A BRACKET-NUT;SV-D10,T0.8,-,-,-,-,T0.8 801 AD61-01601A CASE-TOP;DELTA2-PJ,ABS 94HB,T27.5,W39.5 803 AD64-01160A KNOB-ZOOM;DELTA2-PJ,ABS 94HB,T19.7,W10.9 804 AD61-01622A HOLDER-ZOOM;DELTA2-PJ,POM,T8.9,W23.2,L28 805 AD61-01623A SPRING ETC-ZOOM;DELTA2-PJ,SUS304 WPB,•’0 807 AD63-00567A SHEET-PHOTO;DELTA2-PJ,Œ¡˜˜,T0.2,W7.7,L 808 AD63-00568A SHEET-MIC;DELTA2-PJ,Œ¡˜˜,T0.2,W12.2,L2 809 AD97-08379A ASSY-TOP BOARD;DELTA2-PJ,SC-D103,TOP BOA 811 AD73-00120A RUBBER-MIC;DELTA2-PJ,IIR,8.6X21X6.6,15,­812 AD69-00542A PAD-MIC;DELTA2-PJ,PORON SRS,T0.5,W8.6, 911 6002-001085 SCREW-TAPPING;CH,+,2,M1.7,L5,ZPC(BLK),SW 915 6003-001291 SCREW-TAPTITE;CH,+,B,M1.4,L3.0,ZPC(BLK),
Exploded View and Parts List
3-14 Samsung Electronics
3-7 Ass’y Front
209
204
210
203
205
917
206
208
917
201
917
207
917
Exploded View and Parts List
3-15Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
201 AD97-08450A ASSY-VIDEO LIGHT;-,DELTA2-PJ,VIDEO LIGHT 203 AD61-01598A CASE-FRONT 16X;DELTA2-PJ,ABS 94HB,T27.6, 204 AD73-00119A RUBBER-HOOD;DELTA2-PJ,SILICON,•’34.1XT6, 205 AD61-12033A BRACKET-NUT;SV-D10,T0.8,-,-,-,-,T0.8 206 AD64-01162A WINDOW-REFLECTOR;DELTA2-PJ,PC 94HB,T9.2, 207 AD63-00560A COVER-REFLECTOR;DELTA2-PJ,PC,T17.4,W18.5 208 AD64-01163A WINDOW-REMOCON A;DELTA2-PJ,PMMA,T6.5,W28 209 AD61-01617A HOLDER-LENS HOOD 16X;DELTA2-PJ,PC,T8,W36 210 AD67-00252A LENS-HOOD;DELTA2-PJ,ABS 94HB,L/GARY,•’42 917 6003-001453 SCREW-TAPTITE;BH,+,B,M1.7,L4,ZPC(BLK)
Exploded View and Parts List
3-16 Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
126 AD63-00554A COVER-CONNECTOR;DELTA2-PJ,ABS 94HB,T1.3, 301 AD61-01625A SPRING ETC-BATTERY EJECT;DELTA2-PJ,SUS30 303 AD63-00566A COVER-REAR;DELTA2-PJ,ABS 94HB,T2.1,W5.75 304 AD64-01156A KNOB-BATTERY EJECT;DELTA2-PJ,ABS 94HB,T5 306 AD61-01605A HOLDER-BATTERY EJECT;DELTA2-PJ,POM,T3.1, 307 AD61-01626A BRACKET-JOINT;DELTA2-PJ,SUS304 1/2H,T0.6 308 AD97-08373A ASSY-REAR BOARD;DELTA2-PJ,SC-D103,REAR B 320 AD97-08514A ASSY-UNIT CASE REAR;-,DELTA2-PJ,EXP 901 6002-001085 SCREW-TAPPING;CH,+,2,M1.7,L5,ZPC(BLK),SW
3-8 Ass’y Rear
307
901
308
306
301
304
303
126
320
Exploded View and Parts List
3-17Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
480 AD97-08460A ASSY-HOUSING;-,DELTA2-PJ,EXP 481 AD63-00557A COVER-HOUSING;DELTA2-PJ,ABS 94HB,T42.8,W 482 AD61-01591A BRACKET-GRIP FRONT;DELTA2,SUS304 1/2H,T1 483 AD64-00858A KNOB-TAPE EJECT;BETA-PJ,ABS 94HB,-,-,-,­484 AD97-04814A ASSY-TAPE EJECT;SUS,BETA-PJ,­901 6001-000805 SCREW-MACHINE;CH,+,M1.7,L3,NI PLT,SWRCH1 913 6003-001142 SCREW-TAPTITE;CH,+,B,M1.7,L5,NI PLT,SRWC
3-9 Ass’y Cover Housing
483
484
901
480
913
482
481
Exploded View and Parts List
3-18 Samsung Electronics
3-10 Mechanical Parts (Main Chassis)
M401
M417
405
M402
M404
406
M411
M410
407
M412
M409
401
404
403
M413
406
M403
302
M414
M408
M415
301
M416
M405
M406
Exploded View and Parts List
3-19Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
301 6031-001412 WASHER-PLAIN;POLYSLIDE,CUT,ID0.7,D2.0,T0 302 6031-001417 WASHER-PLAIN;POLYSLIDE,-,ID0.8,D3.0,T0.2 401 6001-001575 SCREW-MACHINE;PH,+,M1.4,L3.5,ZPC(WHT),SW 403 6001-001591 SCREW-MACHINE;PH,+,M1.4,L4(1.5),ZPC(BLK) 404 6001-001715 SCREW-MACHINE;BH,+,M1.4,L2.2,ZPC(BLK) 405 6001-001590 SCREW-MACHINE;PH,+,M1.4,L2.2,ZPC(BLK),SW 406 6009-001319 SCREW-SPECIAL;BH,+,-,M1.4,L2.6,ZPC(YEL), 407 6001-001452 SCREW-MACHINE;BH,+,M1.4,L2.5,BLK,SWRCH18 M401 AD97-06414A ASSY-MAIN CHASSIS;-,DD-4,ASSY M402 AD97-06389A ASSY-LOADING-MOTOR;MOTOR+TEC,DD-4,ASSY M403 AD66-00208A GEAR-TENSION;DD-4,PBT3300,0.5,24,-,-,PCD M404 AD97-07909A ASSY-GEAR-CAM-MAIN;-,DD-4,ASSY M405 AD66-00212A SLIDER-MAIN;DD-4,SUS430 CP,T0.4,-,-,NAT, M406 AD66-00211A LEVER-EJECT;DD-4,DURACON MS-02,-,-,-,-,­M407 AD97-06399A ASSY-DRUM BASE RAIL;-,DD-4,­M408 AD97-06398A ASSY-CAPSTAN MOTOR;-,DD-4,ASSY M409 AD61-01164A HOLDER-FPC SUB;DD-4,DURACON M90-44,-,-,­M410 AD97-06403A ASSY-DRUM;-,DD-4,ASSY M411 AD97-06176A ASSY-GUIDE ROLLER;SUS+ETC,DD-4,­M412 AD61-01483A GUIDE-ROLLER;DD-4,POM,-,-,-,BLACK,MOLD T M413 AD61-00558A PLATE-S/P BASE;DD-3,SUS632 CSP ,T0.15,-, M414 AD66-00221A PULLEY-BELT TIMING;DD-4,POLYURETHAN,-,-, M415 AD66-00069A GEAR-CAPSTAN;DD-3,DYAMID,0.4,28,-,-,PCD M416 AD97-06400A ASSY-ARM-PINCH;-,DD-4,ASSY M417 AD66-00219A GEAR-PULLEY;DD-4,DURACON M90-44,0.3,44,-
Exploded View and Parts List
3-20 Samsung Electronics
3-11 Mechanical Parts (Sub Chassis)
S301
S304
S308
301
S307
401
S311
S312
S313
S310
S302
S303
S306
S309
S305
402
S315
S314
Exploded View and Parts List
3-21Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
301 6031-001412 WASHER-PLAIN;POLYSLIDE,CUT,ID0.7,D2.0,T0 401 6001-001575 SCREW-MACHINE;PH,+,M1.4,L3.5,ZPC(WHT),SW 402 6009-001320 SCREW-SPECIAL;BH,+,,M1.4,L1.7,ZPC(YEL),S S301 AD97-06412A ASSY-SUB CHASSIS;ASSY,DD-4,­S302 AD97-06404A ASSY-COVER-REEL-BRAKE;-,DD-4,­S303 AD97-06390A ASSY-BRAKE T;-,DD-4,ASSY S304 AD97-06395A ASSY-REEL-DISK-S;ASSY,DD-4,­S305 AD97-06396A ASSY-REEL-DISK-T;ASSY,DD-4,­S306 AD97-06397A ASSY-IDLER;ASSY,DD-4,­S307 AD97-06401A ASSY-ARM-TENSION;-,DD-4,ASSY S308 AD61-01184A SPRING ETC-TENSION;DD-4,SUS304-WPB,-,-,­S309 AD97-06402A ASSY-ARM-REVIEW;-,DD-4,ASSY S310 AD97-07213A ASSY-BRAKE-SOFT-S;-,DD-4,ASSY S311 AD61-01195A HOUSING-LOCK R;DD-4,DURACON M90-44 DURA S312 AD61-01194A HOUSING-LOCK L;DD-4,DURACON M90-44 DURA S313 AD97-06394A ASSY-HOUSING;SECC+ETC,DD-4,ASSY S314 AD61-01159A HOLDER-BAND;DD-4,DURACON M90-44,-,-,-,NA S315 AD69-00425A BAND-TENSION;DD-4,LUMIRROR,-,-,-,WHITE,-
Loading...
+ 53 hidden pages