Page 1
IR Dome Camera
User Manual
SCD-1020R
Page 2
IR Dome Camera
User Manual
Copyright
©2011 Samsung Techwin Co., Ltd. All rights reser ved.
Trademark
The name of this product is the registered trademar k of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrit y and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on
the user’s own responsibility. Samsung Techwin reser ves the right to change the contents of this document
without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warrant y period is 3 years. However, the followings are excluded:
If the system behaves abnormally because you run a program irrelevant to the system operation.
•
Deteriorated per formance or natural worn-out in process of time
•
is the registered logo of Samsung Techwin Co., Ltd.
Page 3
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
To prevent damage which may result in fire or electric shock hazard, do not expose this
•
appliance to rain or moisture.
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
•
with the installation instructions.
WARNING
Be sure to use only the standard adapter that is specified in the specification sheet.
1.
Using any other adapter could cause fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
2.
electric shock, or damage to the product.
Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
3.
abnormal heat generation or fire.
Securely plug the power cord into the power receptacle. insecure connection may cause
4.
fire.
When installing the camera, fasten it securely and firmly. The fall of camera may cause
5.
personal injury.
English
Page 4
Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers
6.
filled with water on top of the camera. doing so may cause personal injury due to fire,
electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
7.
electric shock.
If any unusual smells or smoke come from the unit, stop using the product. in such case,
8.
immediately disconnect the power source and contact the service center. continued use in
such a condition may cause fire or electric shock.
If this product fails to operate normally, contact the nearest service center. never
9.
disassemble or modify this product in any way. (samsung is not liable for problems caused
by unauthorized modifications or attempted repair.)
10.
fire or electric shock.
CAUTION
1.
Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibrationor magnetic interference.
2.
Do not install in a location subject to high temperature (over 50°C), low temperature (below
-10°C), or high humidity. Doing so may cause fire or electric shock.
3.
If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4.
Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
5.
Keep out of direct sunlight and heat radiation sources. It may cause fire.
6.
Install it in a place with good ventilation.
7.
Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
8.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9.
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
10.
esuac yam os gniod .tcudorp eht fo strap otno yltcerid retaw yarps ton od ,gninaelc nehW
.DCC eht egamad yam erusopxe ytivitcaoidaR .ytivitcaoidar ot aremac eht esopxe ton oD
4_
English
Page 5
safety information
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions :
This device may not cause harmful interference, and
1)
This device must accept any interference received including interference that may cause
2)
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
(Waste Electrical & Electronic Equipment)
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
English_5
Page 6
important safety instructions
Read these instructions.
1.
Keep these instructions.
2.
Heed all warnings.
3.
Follow all instructions.
4.
Do not use this apparatus near water.
5.
Clean only with dry cloth.
6.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
7.
instructions.
Do not install near any heat sources such as radiators, heat registers, or other apparatus
8.
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
9.
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
10.
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
11.
Use only with cart, stand, tripod, bracket, or table specified by the
12.
manufacturer, or sold with the apparatus.
Unplug this apparatus when a card is used. Use caution when moving
13.
the cart/ apparatus combination to avoid injury from tip-over.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
14.
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
6_
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
English
Page 7
Contents
CAMERA
CONNECTING WITH OTHER
DEVICE
PRODUCT SPECIFICATION
8
Part Names
Package Contents
8
6
9
Installing the camera
Adjusting the monitoring direction
10
for the camera
9
Product specification
11
11
English_7
Page 8
AMERA
Video Output
Jack
Power Input
Connector
C
Part Names
Name Description
b
c
IR LED
Lens
Illumination
Sensor
These infrared LED's are controlled by the illumination sensor.
Focal length of 3.6mm enables you to cover relatively longer range of monitoring.
Detects incoming light to control the IR LED.
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
Connect the adaptor to the power input connector
PACkAgE CONTENTs
b
c
IR Dome Camera
User Manual
SCD-1020R
8_
Camera
English
Screw (3EA)
User manual
Page 9
connecting with other device
Installing the camera
Precautions before installation
Ensure you read the following instructions before installing the camera:
ySelect an installation site (ceiling or wall) that can endure at least 5 times of the camera weight.
yStuck-in or peeled-off cables can cause damage to the product or a fire.
1. Hold down the bottom lock lever while removing the cover with the
other hand.
2. Press and hold the lock key outward (in the arrow direction) and turn
the bracket counter clockwise to remove it.
;
3. Use the provided screws (x3) to fix the bracket to a desired
position (ceiling or wall).
Ensure that the <CAMERA FRONT> label on the bracket faces the
`
direction for camera monitoring.
Wiring Cover
English
_9
Page 10
4. Arrange the cables through the bracket to the ceiling or wall.
10_
If you intend to drill a hole in the installation site for the wiring purpose, remove the wiring cover to reveal a
hole. Arrange the cables through the hole.
If you intend to arrange the cables without drilling a hole, use the empty area opposite to the <CAMERA
FRONT> label side for the wiring purpose.
5. Mount the main unit onto the bracket.
Align the marking hole of the main unit with the <CAMERA FRONT>
label of the bracket, and turn the unit in the <LOCK> direction.
6. Adjust the lens in a desired direction.
For adjusting the lens direction, refer to “Adjusting the monitoring
direction for the camera”.
7. Fix the cover to the main unit.
Align the lock key of the main unit with the latch of the cover. Press
down the cover until you hear a click.
Adjusting the monitoring direction for the camera
Panning Lens rotationTilting
You can adjust the camera direction only when the camera is fixed on the ceiling.
Then, turning the camera to the left or right is referred to as "Panning", while tilting the angle is "Tilting".
- If you want to adjust the panning direction, loosen the bottom screw and turn the camera to a desired
direction. Then, tighten the screw back.
If you couldn’t tighten the screw for positioning reasons, select a different screw hole and try again.
- The tilting is available between 0˚ and 60˚. When you finish adjusting the tilt, tighten the tilt adjustable screw
if you want to fix the angle.
- If you install the camera vertically on a slanting ceiling or wall, the video from the camera may not be
displayed properly. If this is the case, adjust the lens direction to correct the display of the video.
English
Page 11
specifications
speCIfICATIONs
Item
Video
Imaging Device
Sensor Format
Scanning System
Synchronization
Frequency
Horizontal Resolution
Min. Illumination
S/N Ratio (Y Signal)
１／４＂ ＣＭＯＳ
680 x 512
Interlace
Internal
H : 15.734KHz / V : 59.94Hz
520 TV lines
OLux (IR-LED ON)
46dB
SCD-1020R
Video Output
Lens
Focus Length
Max.Aperture Ratio
Angular Field of View
Operational
Shutter Mode
Gain Control
White Balance
Day/Night
Digital Noise Reduction
IR Distance
Environmental
Operating Temperature / Humidity
CVBS : 1.0 Vp-p / 75Ω composite
3.6mm
2
H: 56° / V: 42°
Auto (Rolling Shutter)
Auto
Auto (3200°K~6500°K)
Auto
Auto
10m( IR LED 12EA)
-10°C ~ +50°C (+14°F ~ +122°F) Less than 90% RH
English_11
Page 12
Item
Electrical
Input Voltage
Power Consumption
Mechanical
Dimension
(W x H
Weight
SCD-1020R
DC 12V
2.2W
102 X H71.7
)
Ø
180g
12_
English
Page 13
MEMO
Page 14
MEMO
Page 15
MEMO
Page 16
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300, FAX : +44-1932-45-5325
PT01-000620A
Loading...