Samsung SCC-C7478 User Manual
SCC-C7478
36x Smart Dome Camera
User’s Guide
ENG FRE
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/global/register
GER SPA
ITA
Safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..
This symbol indicates high voltage is present inside. It is dangerous to make any kind of
contact with any inside part of this product.
This symbol alerts you that important literature concerning operation and maintenance has
been included with this product.
WARNING
•
To prevent damage which may result in fi re or electric shock hazard, do not expose this appliance to rain or
moisture.
WARNING
1.
Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet. Using any other adapter
could cause fi re, electrical shock, or damage to the product
2.
Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or
damage to the product.
3.
Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fi re.
4.
Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.
5.
When installing the camera, fasten it securely and fi rmly. A falling camera may cause personal injury.
6.
Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers fi lled with water
on top of the camera. Doing so may cause personal injury due to fi re, electric shock, or falling objects.
7.
Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.
8.
If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fi re or electric shock.
9.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify
this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or
attempted repair.)
When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.
10.
If the camera is installed or rebooted after power failure when ambient temperature is below the freezing point,
11.
the dome cover is frosted. In this case, the frost will be disappeared after 3 hours after turning on the power.
(It is noted that lowest guaranteed operating temperature is -45º C (-49º F) without wind.)
2 – 36x SMART DOME CAMERA
Safety information
CAUTION
Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to
1.
excessive vibrationor magnetic interference.
Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high
2.
humidity. Doing so may cause fi re or electric shock.
If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall
3.
it.
Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fi re or
4.
damage to the product.
Keep out of direct sunlight and heat radiation sources. It may cause fi re.
5.
Install it in a place with good ventilation.
6.
Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
7.
CCD image sensor.
Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases,
8.
shall be placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
9.
ENG
English – 3
Important Safety Instructions
Read these instructions.
1.
Keep these instructions.
2.
Heed all warnings.
3.
Follow all instructions.
4.
Do not use this apparatus near water.
5.
Clean only with dry cloth.
6.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7.
Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that
8.
produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
9.
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician
for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
10.
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specifi ed by the manufacturer.
11.
Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold
12.
with the apparatus.
Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid
13.
injury from tip-over.
Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in
14.
any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
4 – 36x SMART DOME CAMERA
Contents
Introduction
Features 6
Product & Accessories 7
Parts Name & Functions 8
Installation
DIP Switch Setup 9
Installation using Mount Bracket 10
Cabling 13
Operation
Check points before operation 15
Preset and Pattern Function Pre-Check 15
AUTO CALIBRATION 15
Starting OSD Menu 15
Reserved Preset 15
Preset 16
Auto Pan 16
Pattern 16
Scan 16
Schedule 17
Other Functions 17
OSD Display of Main Screen 18
General Rules of Key Operation for Menu 18
ENG
How to use OSD Menu
Main Menu 19
System Information 19
Display Setup 19
PRIVACY ZONE MASK Setup 19
Motion Setup 20
Function Setup 21
PRESET Setup 22
Auto Pan Setup 23
Pattern Setup 23
Scan Setup 24
Schedule Setup 26
CAMERA SETUP 27
System Setup 28
System Initialize 30
Specifi cations
Specifi cations 31
Dimension 32
English – 5
Introduction
FEATURES
Camera Specifi cations
❖
CCD Sensor : EX-view HADTM CCD
•
Zoom Magnifi cation : × 36 Optical Zoom, × 12
•
Digital Zoom (Max × 432 Zoom)
Wide Dynamic Range Function
•
Day & Night Function : ICR(IR Cut fi lter Removal)
•
Various Focus Mode : Auto Focus / Manual Focus
•
/ Semi-Auto Focus.
•
Independent or Global camera settings for each
Preset locations.
Powerful Pan/Tilt Functions
❖
•
Max. 360°/sec high speed Pan/Tilt Motion
•
Using Vector Drive Technology, Pan/Tilt motions
are accomplished in the shortest path. As a result,
time to target view is reduced dramatically and the
video on the monitor is very natural to watch.
•
Ultra low speed (0.05°/sec) enables operator
to locate camera to desired target view with
accuracy and ease.
•
Zoom-proportional pan/tilt speed helps operator
to move the camera easily.
Preset, Pattern, Auto Pan, Scan, Privacy
❖
Mask, Schedule and More…
MAX. 127 Presets are assignable. All of them
•
have independent characteristics such as White
Balance, Auto Exposure, Label, Alarm Input/
Output and so on.
Max. 8 set of Auto Pan can be stored. This
•
enables to move camera repetitively between two
preset positions with designated speed.
Max. 4 of Patterns can be recorded and played
•
back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
Max. 8 set of Scan action can be stored.
•
This enables to move camera repetitively with
combination of Preset or Pattern or Auto Pan. A
Scan is composed of max. 20 entities of Preset/
Pattern/Auto Pans.
Max 8 Privacy Masks can be set up to protect
•
privacy of other people.
7 rules of Schedule can be assigned by day and
•
time. Appropriate actions (such as Home, Preset,
Scan, Pattern and Auto Pan) can be defi ned for
each rule. Also, it is possible to use Weekday and
All days to simplify the rule.
PTZ(Pan/Tilt/Zoom) Control
❖
With RS-485 communication, max. 255 of
•
cameras can be controlled at the same time.
•
Pelco-D/ Pelco-P/ Samsung protocol can be
selected as a control protocol in the current
version of fi rmware.
OSD(On Screen Display) Menu
❖
OSD menu is provided to display the status
•
of camera and to confi gure the functions
interactively.
The information such as Camera ID, Pan/Tilt/
•
Zoom/Direction, Alarm Input & Output, date/time,
current temperature and Preset can be displayed
on screen.
Each display item can be turned on or off
•
independently.
Alarm I/O Functions
❖
8 alarm sensor Inputs and 4 relay output are
•
available.
To reject external electric noise and shock
•
perfectly, alarm sensor Input is decoupled with
photo coupler.
The signal range of sensor input is from DC 5.0 to
•
12.0 volts to adopt various applications.
If an external sensor is activated, camera can be
•
set to move to the corresponding Preset position.
Relay outputs can be assigned to work with a
•
certain preset.
Reserved Presets for Special Purpose
❖
Most of camera settings are directly changed by
•
calling Reserved Presets, not entering into OSD
menu. For more information,refer to “Reserved
Presets”(page 15) in this manual.
6 – 36x SMART DOME CAMERA
PRODUCT & ACCESSORIES
Product❖
Wall Mount Type Ceiling Mount Type
Accessories❖
Introduction
ENG
Hexagonal wrench Anchor bolts (4pcs) Water proof tape
Hole Template
User’s Guide Safety Cable
Housing Safety Cable
Hanger
English – 7
Introduction
PARTS NAME & FUNCTIONS
SUN SHIELD & UPPER
HOUSING
PTZ MECHANISM
DOME SAFETY CABLE
FAN
HEATER
Dome Cover
•
Do not detach protection vinyl from dome cover
before fi nishing all installation process to protect
dome cover from scratches or dust.
In the dome cover, there are Fan and Heater to
remove moisture on the bubble dome.
Sunshield & Upper housing
•
Sunshield protect bubble dome cover from the sun
rays and rain fall from. In the sunshield, there is the
upper housing which will contain accommodate
PTZ mechanism. Also, the upper housing will be
connected to both mounting brackets and dome
cover.
FAN & HEATER CABLE
DOME COVER
INNER BOX
HOUSING SAFETY CABLE HANGER
Wall/Ceiling mount Bracket
•
These are used to install the camera on the wall or
ceiling and have junction box. The junction box of the
bracket accommodate inner box.
Inner box
•
The inner has many important roles of connection
box between camera and outside. Top of the box,
there are dip switches and terminal blocks for Power
supply, Video, Communication, Alarm Input/output.
8 – 36x SMART DOME CAMERA
DIP SWITCH SETUP
Installation
❖
Communication Protocol Setup
Before you install the camera, you should set the DIP
switches to confi gure the camera ID, communication
protocol.
w
WWWGaGhGw
WWXGaGwTk
WWYGaGwTw
WWZGaGzhtz|un
Camera ID Setup
❖
ON
ON
pkGzGOX¥Y\\P
iGy
WWWGaGY[WW
WWXGaG[_WW
WWYGaG`]WW
WWZGaGX`YWW
WW[GaGZ_[WW
yzT[_\
{
ON
ON
123456
Select the appropriate Protocol with DIP switch
•
78
combination.
Switch State
Pin1 Pin2 Pin3 Pin4
OFF OFF OFF OFF Auto Protocol
ON OFF OFF OFF PELCO-D
OFF ON OFF OFF PELCO-P
ON ON OFF OFF SAMSUNG
If you set the protocol as Auto Protocol, camera will
•
Protocol
automatically recognize the kind of Protocol.
If you want to control using DVR or system keyboard,
•
their protocol must be identical to camera. Otherwise,
you can not control the camera.
If you changed camera protocol by changing DIP S/W,
•
the change will be effective after you reboot the camera.
Factory default of protocol is “Auto” Protocol
•
Communication Baud rate Setup
❖
ENG
123456
ID number of camera is set using binary number.
•
78
The example is shown bellow.
Pin 12345678
ID Value 1 2 4 8 16 32 64 128
ex) ID=5
ex) ID=10onoff
The range of ID is 0~255. Factory default of
•
offonon
off
offonoff
off
off
off
off
off
Camera ID is 1.
If you want to control a certain camera, you must
•
match the camera ID with Cam ID setting of DVR
or Controller.
off
off
ON
ON
123456
Select the appropriate Baud rate with DIP switch
•
78
combination.
Switch State
Pin5 Pin6 Pin7
OFF OFF OFF 2400 BPS
ON OFF OFF 4800 BPS
OFF ON OFF 9600 BPS
ON ON OFF 19200 BPS
OFF OFF ON 38400 BPS
•
Factory default of Baud rate is “9600 BPS”
Protocol
English – 9
Installation
A
RS-485 Termination Resistor
❖
ON
ON
123456
Pin 8 is used for ON/OFF of RS-485 Termination.
•
78
Normally, it must be OFF state. Especially when
you have trouble with long Daisy chain style
connection, turn ON this termination switch of last
camera.
Pin 8 RS-485 Termination Resistor (On/Off)
–
INSTALLATION USING MOUNT
BRACKET
① Using the paper template, mark the holes on the
wall.
③ After locating the wall mount bracket on the
anchor bolts properly. Tighten the nuts for
anchor bolts
② After drilling the holes, fi x the four anchor bolts
into the holes.
10 – 36x SMART DOME CAMERA
④ Connect cables to terminal blocks and BNC in
the inner box of junction box. See the cabling in
the next section.
Connector to the dome camera
Protocol,
Address DIP
RS-485
POWER
BNC
VIDEO
LARM
Loading...