Samsung SCC-C6403 User Manual

SmartDome Camera

SCC-C6403

Owner’s Instructions

Manuel d’instruction

Manual del usuario

E

F

Es

J

Part : AB68-00570A(00)

Safety PrecautionsImportant Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the
manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, or
other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding- type plug. A
polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the
apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus.

The purpose of this information is to ensure proper use of this product to
prevent danger or damage to property. Please be sure to observe all
precautions.

* The precautions are divided into "Warnings" and "Cautions" as

distinguished below:

Warning: Ignoring this warning may result in death or serious injury.
Caution: Ignoring this caution may result in injury or damage to property.

Warning instructions alert you to

a potential risk of death
or serious injury.

Caution instructions alert you to the

potential risk of injury or
damage to property.

Warning

1. Be sure to use only the standard adapter which is specified in the
specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to
the product.

2. When connecting the power supply and signal wires, check the external
connection terminals before connecting them. Connect the alarm signal
wires to the alarm terminals, the AC adapter to the AC power input
receptacle, and the DC adapter to the DC power input, making sure that
the correct polarity is observed.
(Connecting the power supply incorrectly may cause fire, electrical shock,
or damage to the product.)

E

13. Unplug this apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.

14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.

3. Do not connect multiple cameras to a single adapter.
(Exceeding the capacity may cause abnormal heat generation or fire.)
(A falling camera may cause personal injury.)

4. Securely plug the power cord into the power receptacle.
(Insecure connection may cause fire.)

5. When installing the camera on a wall or ceiling, fasten it securely and
firmly. (A falling camera may cause personal injury.)

6. Do not place conductive objects (e.g., screwdrivers, coins, and metal
things) or containers filled with water on top of the camera. (Doing so may
cause personal injury due to fire, electrical shock, or falling objects.)

7. Do not install the unit in humid, dusty, or sooty locations.
(Doing so may cause fire or electrical shock.)

8. If any unusual smells or smoke come from the unit, stop using the product.
In such case, immediately disconnect the power source and contact the
service center. (Continued use in such a condition may cause fire or
electrical shock.)

9. If this product fails to operate normally, contact the store of purchase or
your nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized
modifications or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product.

(Doing so may cause fire or electrical shock.)
Wipe the surface with a dry cloth. Never use detergents or chemical
cleaners on the product, as this may result in discoloration of surface or
cause damage to the finish.

Caution

1. Do not drop objects on the product or apply strong shock to it. Keep away
from a location subject to excessive vibration or magnetic interference.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference

that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

2. Do not install in a location subject to high temperature (over
temperature (below 14°F
(Doing so may cause fire or electrical shock.)

3. Avoid a location which is exposed to direct sunlight, or near heat sources
such as heaters or radiators.
(Neglecting to do so may result in a risk of fire.)

4. If you want to relocate the already installed product, be sure to turn off the
power and then move or reinstall it.

5. Install in a well-ventilated location.

6. Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)

), or high humidity.

122°F), low

Before Usage

Table of contents

This is a basic instruction manual for the SCC-C6403 user.
It contains all the instructions needed to use the SCC-C6403 from
a simple introduction of the control locations and functions of the
SCC-C6403 to installation methods in the set up menu.

We recommend all users of the SCC-C6403 from the advanced
user who has used similar cameras before to the general user to
read the instruction manual before using.

The most frequently used feature in the SCC-C6403 would be the
SCC-C6403 Setup Menu.
The SCC-C6403 Setup Menu is explained in detailed in "Chapter
3 Setup Menu Overview".

The instructional manual is best used when read from beginning
to end, but for users wanting to read only the part they need here
are the Chapter summaries.

"Chapter 1 SCC-C6403 Overview" includes a brief introduction
of the SCC-C6403, part names and functions, and Switch
Settings.

"Chapter 2 SCC-C6403 Installation" explains the installation
procedures of the SCC-C6403 and provides preparation and
installation environment requirements.

"Chapter 3 Setup Menu Overview" presents the structure of the
Setup menu for the SCC-C6403 including a detailed explanation
of the functions performed in each submenu.

"Appendix SCC-C6403 Product Specifications" contains
product specifications of the SCC-C6403 in itemized categories.

1-1

Before Usage...............................................................................................................1-1

Chapter 1

Chapter 2

Chapter 3

SCC-C6403 Overview..............................................................................1-4

SCC-C6403 Introduction .............................................................................1-5

Locations of Control….................................................................................1-6

ADAPTER CONNECTION ..........................................................................1-8

INITIAL SETTING........................................................................................1-9

Setting RS-422A/RS-485 termination........................................................1-10

SCC-C6403 Installation...........................................................................2-1

Before Installing...........................................................................................2-2

Preparing the Cables...................................................................................2-3

Cable Connection........................................................................................2-4

Installing SCC-C6403..................................................................................2-5

Installing the Camera ..................................................................................2-8

Setup Menu Overview .............................................................................3-1

Structure of the Setup Menu........................................................................3-2

1. CAMERA SET MENU .............................................................................3-4

- CAMERA ID .........................................................................................3-4

- V-SYNC................................................................................................3-5

- COLOR/BW..........................................................................................3-6

- MOTION DET.......................................................................................3-7

- ZOOM SPEED .....................................................................................3-8

- DIGITAL ZOOM ...................................................................................3-9

- DISPLAY ZOOM ..................................................................................3-9

- DISPLAY P/T .......................................................................................3-9

- EXIT ...................................................................................................3-10

2. VIDEO SET MENU ...............................................................................3-10

- IRIS....................................................................................................3-10

- ALC.................................................................................................3-10

- BLC...............................................................................................3-10

- MANU .............................................................................................3-11

- SHUTTER ..........................................................................................3-12

- FLICKERLESS ................................................................................3-12

- AGC ...................................................................................................3-13

- MOTION.............................................................................................3-13

- WHITE BAL........................................................................................3-14

- DIS.....................................................................................................3-15

- FOCUS MODE...................................................................................3-16

- SPECIAL............................................................................................3-16

- EXIT...................................................................................................3-17

3. PRESET ................................................................................................3-17

- POSITION SET .................................................................................3-18

- PRESET ID........................................................................................3-18

- VIDEO SET........................................................................................3-18

- PRESET SPEED ...............................................................................3-18

- DWELL TIME.....................................................................................3-18

- IMAGE HOLD ....................................................................................3-18

- EXIT...................................................................................................3-18

E

1-2

4. ZONE SET...............................................................................................3-19

- ZONE DIR SET....................................................................................3-19

- ZONE AREA SET................................................................................3-20

- LOCATION .......................................................................................3-21

- ZONE ID SET ...................................................................................3-21

- ZONE ENABLE.................................................................................3-21

5. AUTO SET...............................................................................................3-22

- AUTO PAN ..........................................................................................3-22

- POSITION SET.................................................................................3-22

- SPEED..............................................................................................3-23

- DWELL TIME....................................................................................3-23

- PATTERN............................................................................................3-23

- SCAN...................................................................................................3-24

- AUTO PLAY.........................................................................................3-25

- AUTO RETURN................................................................................3-25

- AUTO PLAY......................................................................................3-25

- PLAY NUMBER................................................................................3-25

6. ALARM SET ............................................................................................3-26

- ALARM PRIORITY SET ......................................................................3-26

- ALARM IN SET....................................................................................3-26

- ALARM OUT SET................................................................................3-26

- AUTO SET...........................................................................................3-27

- AUX OUT CONTROL ..........................................................................3-27

7. OTHER SET............................................................................................3-27

- PROPORTINAL P/T ............................................................................3-27

- TURBO P/T..........................................................................................3-28

- AUTO CAL...........................................................................................3-28

- AUTO FLIP ..........................................................................................3-28

- CAM RESET........................................................................................3-28

- LANGUAGE.........................................................................................3-28

- PASSWORD........................................................................................3-28

8. SYSTEM INFO ........................................................................................3-29

9. Short Keys...............................................................................................3-30

Product specifications ..........................................................................................3-32

Chapter 1 SCC-C6403 Overview

In this chapter we will briefly introduce the SCC-C6403 and
show main functions, locations of control and Switch Setting.

E

1-3 1-4

SCC-C6403 Introduction

Locations of Control

SCC-C6403 is a zoom lens built in smart dome camera which
provides you with the best monitoring function in connection with
CCTV at banks or companies.

The SCC-C6403 is a high quality surveillance camera using x32
zoom lens and digital zoom IC, it can catch clear images up to 320
times.

SCC-C6403 has a variety of functions such as;

- DAY/NIGHT to improve the sensitivity by automatic conversion
into the black and white mode at night or in the environment with
low illumination,

- White Balance to control the brightness to the illumination,

- Backlight Compensation under spotlight or utmost bright
illumination,

- Auto Focus to automatically adjust the focus to the subject
movement,

- PAN/TILT for an easy operation.

The SCC-C6403 uses an Alarm function for alert situations and
moving camera in the direction you want, ZOOM-IN and
ZOOM-OUT functions can be remote controlled.

FRONT

E

1-5

1-6

ADAPTER CONNECTION

AC 24V

OUT

POWER

AC 24V

OUT

POWER

BACK

SCC-C6403 Adapter BOARD

E

1-7

1-8

12

INITIAL SETTING

(x100) (x10) (x1)

SW704

ON

1 2 3 4 5 6 7 8

SW701 SW702 SW703

SEE INSTRUCTION MANUAL

CAMERA ADDRESS SETUP

Use SW701, SW702, or SW703 for Camera Address setup. You may
allocate up to 255 addresses by using SW701 to set the 3rd digit, SW702
the 2nd digit, and SW703 the 1st digit.
EX) In case of Camera Address 1, see the following figure for setup.

SW701

SW702

Setting communication Protocol

Use number 1~4 PIN of SW704 to set communication Protocol.

PIN

PIN1 PIN2 PIN3 PIN4

Comp

A OFF OFF OFF OFF
B ON OFF OFF OFF
C OFF ON OFF OFF
D ON ON OFF OFF
E OFF OFF ON OFF
F ON OFF ON OFF
G OFF ON ON OFF
H ON ON ON OFF

I OFF OFF OFF ON
J ON OFF OFF ON
K OFF ON OFF ON
L ON ON OFF ON
M OFF OFF ON ON
N ON OFF ON ON
O OFF ON ON ON
PONONONON

SW703

A : SAMSUNG HALF
B : SAMSUNG FULL

(BOTTOM VIEW)

Setting RS-422A/RS-485 termination

As it is shown in the structure map, when Controller and RS-422A/RS­485 is connected it should be terminated according to the Cable feature
of impedance on the each end of the transmitting line to transfer the
signals in long distance by controlling the reflection of the signals to the
lowest.

Division

<RS-485 Half Duplex Organization>

Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.

Division

n < 32

Termination

SW1-ON

n < 32

Division
SW1-ON
SW2-ON

E

Baud Rate Setting

Use PIN 5 and 6 of SW704.

1 2 3 4 5 6 7 8

ON

OFF

1-9

BAUD RATE
4800 BPS
9600 BPS
19200 BPS
38400 BPS

The factory default setting is set to 9600BPS.

SW 704

PIN 5

ON

OFF

ON

OFF

PIN 6

ON

ON
OFF
OFF

<RS-422A/RS-485 Full Duplex Organization>

❈

A communication error may occur if you connect multiple cameras that are
assigned the same address in the network.

1-10

AC 24V

OUT

POWER

Chapter 2 SCC-C6403 Installation

In this chapter, we will check the contents of the package before
installing the SCC-C6403, and prepare a power adapter suitable for
the power supply system.
(Power Consumption: 18W; Voltage: AC24V, 1.5A)
Then, we will install the SCC-C6403 and connect the cables.

Before Installing

Checking Package Contents

Please check that all components listed below are included in the
package:

SCC-C6403

Owner’s
Instructions

Bracket anchor

E

2-1

Screws

Camera Holder

Cover Body (Option)

Adapter Board

2-2

Preparing the Cables

Cable Connection

To install and use the SCC-C6403, the following cables should be
prepared.

Power Adapter Cable

The cable that plugs into the SCC-C6403 power input receptacle has the
rated voltage of AC24V, 1.5A.
Check the rated voltage before using the cable.

Video Cable

The SCC-C6403's cable is a BNC Cable for connecting the video-output
terminal to the video-input terminal of the monitor.

1. First, connect one end of the
BNC video cable connector to
the Video Output Terminal
(VIDEO OUT)

2. Then, connect the other end of
the connector to the Video Input
Terminal of the monitor.

3. Now connect the Power Adapter
Cable. Use a driver to screw
one part of the two lines of
Power Adapter to Power Input
Terminal of the SCC-C6403.

4. Adjust the switch on the Power Adapter to the proper voltage.
Then, connect the Power Adapter's plug to the Power Connector.

E

5. Connect the Remote Control
Terminal of the
SCC-C6403
and the external Controller.

Controller

2-3 2-4

Adapter BOARD

Installing SCC-C6403

Installation Precautions

1) Make sure that the installation site can sufficiently support a minimum of
four times the net weight of the SCC-C6403 SmartDome Camera and
other accessories.

2) Install in an area where the space above the ceiling board is over 18 cm
(7 in.) high.

3) Use the supplied screws to fasten the camera to the bracket assembly.

4) Keep persons away from the installation area, as there is a risk of falling
objects.
Also, move valuables to a safe location before installation.

Separately Sold Products for Installation

Depending on the installation site, it may be convenient to use one of the
following products.

1) CEILING MOUNT BRACKET

(SBR-100DCM)

This bracket is used for installing
the SmartDome CAMERA in the
plenum above the drop ceiling.

3) INDOOR HOUSING (SHG-120)

This housing is used for installing the SmartDome Camera to an indoor
wall or a ceiling.

E

4) OUTDOOR HOUSING (SHG-220)
This housing is used for installing the SmartDome Camera to an
outdoor wall or a ceiling.

2) WALL MOUNT ADAPTOR
(SADT-100WM)

This adaptor is used for installing the
indoor housing or the outdoor
housing for the SmartDome Camera
on a wall.

2-5

❈

To install and use OUTDOOR HOUSING, remove the Clear Case
from the Camera body before installation.

2-6

5) CEILING MOUNT ADAPTOR (SADT-100CM)

This adaptor is used for installing the indoor housing or the outdoor
housing for the SmartDome Camera to a concrete ceiling.

6) POLE MOUNT ADAPTOR (SADT-100PM)

This adaptor is used for installing the WALL MOUNT ADAPTOR
(SADT-100WM) to a pole that is over 8 cm (2.76 in.) in diameter.

Installing the Camera

1. [Figure 1] Install the structure on the
ceiling.
(Refer to Installation reference

for the Length of the structure)

* Built in by the builder of the structure

E

[Figure 1]

2. Make a hole in the ceiling where the camera will be installed.

(The hole should be about ø185)

3. [Figure 2] Assemble the
BRKT-ANCHOR on the ceiling
and screw the 4 bolts in.

2-7

[Figure 2]

4. [Figure 3,4] Connect the various cables to the CAMERA ADAPTER.
(See page 2-4)

[Figure 3]

[Figure 4]

2-8

5. [Figure 5] Match the
BRKT-ANCHOR and CAMERA
ADAPTER and use 4screws
(PH M4 x 8) to assemble them.

[Figure 5]

6. Pull the safety wire from the case
body, and assembly it to the camera
holder.

[Figure 6]

Chapter 3 Setup Menu Overview

In this chapter, we will look over the Setup Menu of the
SCC-C6403, First we'll look over the overall structure of the
Setup Menu, and then we'll look at the functions of each menu.

E

7. [Figure 7] Match the 3 holes on the
back of the CAMERA and the
CONNECTOR and turn it left about
15 degrees.
(Check the sound of LOCKING

and that the LEVER-LOCKING
is in place)

* Use the screws (BH M3 x L8) to

connect the CAMERA and the
ADAPTER so they don't move.

8. [Figure 8] Assemble the
COVER-BODY onto the DOME.

2-9

[Figure 7]

[Figure 8]

3-1

Structure of the Setup Menu

CAMERA SET

VIDEO SET IRIS ALC.../MANU...

PRESET POSITION SET ...

ZONE SET ZONE DIR SET OFF/ON...

CAMERA ID ON.../OFF
V-SYNC INT/LINE...
COLOR/BW COLOR.../BW.../AUTO...
MOTION DET OFF/ON...
ZOOM SPEED 1/2/3/4
DIGITAL ZOOM 0FF/X2 ~ X10
DISPLAY ZOOM
DISPLAY P/T OFF/ON
EXIT QUIT/SAVE/PRESET

SHUTTER OFF/1/100(1/120)~1/10K/AUTOX2...~X128...
AGC/MOTION OFF/LOW/HIGH(AGC)

WHITE BAL ATW1/ATW2/AWC/MANU...
DIS ON/OFF
FOCUS MODE ONEAF/MF
SPECIAL ...

EXIT QUIT/SAVE/PRESET

PRESET ID ON.../OFF
VIDEO SET ON.../OFF
PRESET SPEED 1~8
DWELL TIME 1~60S
IMAGE HOLD ON/OFF
EXIT QUIT/SAVE/DEL

ZONE AREA SET
EXIT QUIT/SAVE

OFF/ON

S.SLOW/SLOW/NORM/FAST/F.FAST(MOTION)

Y-LEVEL (0)l--­C-LEVEL (0)l--­DETAIL (0)l--­RET

OFF/ON...

ALARM SET ALARM PRIORITY SET ALARM1~4 1~4

EXIT QUIT/SAVE

ALARM IN SET ALARM1~4 NO/NC/OFF

EXIT QUIT/SAVE

ALARM OUT SET ALARM1~4 1~3

MOTION 1~3
EXIT QUIT/SAVE

AUTO SET ALARM1~4

MOTION
EXIT QUIT/SAVE

AUX OUT CONTROL OUT1 ON/OFF

RET

OTHER SET PROPORTIONAL P/T ON/OFF

TURBO P/T ON/OFF
AUTO CAL OFF/6H/12H/18H/24H
AUTO FLIP ON/OFF
CAM RESET ...
LANGUAGE
PASSWORD ON.../OFF
EXIT QUIT/SAVE

SYSTEM INFO

OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4

OUT2 ON/OFF
OUT3 ON/OFF
EXIT QUIT/SAVE

ENGLISH/FRANÇAIS/ESPAÑOL/JAPANESE

The diagram shown above illustrates the overall structure of the Setup Menu.
In this section, a description of the Setup menu features will enable users of the
SCC-C6403 to tailor it to their personal needs.

E

3-2

AUTO SET AUTO PAN 1.../2.../3.../4...

PATTERN 1.../2.../3...
SCAN 1.../2.../3.../4...
AUTO PLAY ...
RET

3-3

❈

If the power is turned off after PRESET, AUTO PAN, SCAN,
PATTERN function is activated and no other control is made, camera
will do the same function after the power is turned on.

Use the controller to press the MENU selection key and the following
screen will be displayed.

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET ...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

PASSWORD

➀

UNDEFINED

In case of
setup. In case of

, use UP/DOWN/LEFT/RIGHT/[ENTER] key for MENU

➀

, type in the 4 digit password first. If correct, the

➁

MENU selection screen like

will be displayed and you will be able to

➀

0 1 2 3 4
5 6 7 8 9

✽ ✽ ✽ ✽

➁ PASSWORD

DEFINED

set up MENU by pressing UP/DOWN/LEFT/RIGHT/[ENTER] key.

(CAMERA SET)

CAMERA ID ON...
V-SYNC INT
COLOR/BW
MOTION DET OFF
ZOOM SPEED 3
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

COLOR

...

➜

Press

[Enter]

(CAMERA ID)

A B C D E F G H I J K L
M N O PQ R S T U V W X
Y Z 0 1 2 3 4 5 6 7 8 9

✻

()/

: ! - +

SP

ï î

LOCATION...
RET

SCC-C6403........

SP

❈ " ... " Means there are Sub Menus.

V-SYNC

In the V-SYNC menu, vertical synchronization can be selected. The
vertical synchronization signal supported by the SCC-C6403 is the INT
mode made by clock inside the SCC-C6403 and LINE mode adjusting
vertical synchronization to the exterior power frequency.

Select LINE and press [Enter]. You will see the LINE LOCK submenu
where you can adjust the phase of the LINE LOCK.
You can use the PHASE menu of the LINE LOCK submenu to assign as
much PHASE as you want.

E

1. CAMERA SET MENU

CAMERA ID

The CAMERA ID menu assigns an ID to the SCC-C6403 to be displayed on
the connected monitor.On the CAMERA SET menu screen, select CAMERA
ID to ON and press [Enter]. You will see the sub screen for deciding on the
ID of the SCC-C6403. The Camera ID can have up to 20 alphanumeric
characters, along with several special characters.
The assigned camera ID may be positioned to any desired location on the
screen by using the LOCATION submenu.

3-4

(CAMERA SET)

CAMERA ID OFF
V-SYNC LINE...
COLOR/BW
MOTION DET OFF
ZOOM SPEED 3
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

COLOR

(LL-PHASE)

...

➜

Press

[Enter]

PHASE (-262)I-------­RET

3-5

COLOR/BW

In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.
In a poor illumination environment, the IR filter is turned off in the BW mode the its
sensitivity increases as high as a black and white camera. On the other hand, the
IR filter is turned on and the sensitivity decreases in the COLOR mode.
COLOR : The IR Filter is ON and the screen is normal. You can press the

[Enter] key to set the COLOR GAIN LEVEL. And when the AGC
function is on, you can set the AGC COLOER LEVEL.

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW COLOR …
MOTION OFF
ZOOM SPEED 3
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

➜

Press

[Enter]

BW : The IR Filter is OFF and the screen is black and white.

(Sensitivity to low light is increased to a level comparable to a black
and white camera.)
Select BW and press [ENTER] and the additional menu to select
BURST ON/OFF will appear.

AUTO : Select to automatically switch between the COLOR mode and BW

mode depending on the amount of light. In low light conditions, the
IR Filter is turned OFF and the sensitivity to low light is increased
by switching to the BW mode, but in bright light conditions, the IR
Filter is turned ON and the sensitivity is decreased by switching to
the COLOR mode.
Select AUTO and press [ENTER] and the additional menu to select
BW LEVEL and DURATION will appear.

- BURST ON : The color burst signal is output together with black and white
composite video signal.

- BURST OFF : The color burst signal is not output.

- LEVEL : You can set the brightness level that changes from COLOR mode

to BW mode in 3 steps : LOW, MEDIUM, and HIGH.

- DURATION : Set the HOLDING time for switching between COLOR and BW

mode depending the changes in the amount of light. You can set
the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).

(COLOR)

GAIN (0)I-------­AGC COLOR (0)----I---­RET

❈

In AUTO mode, AGC will be displayed as “---“. You can’t adjust the
settings manually.

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW AUTO...
MOTION DET OFF
ZOOM SPEED 3
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

➜

Press

[Enter]

(AUTO)

BURST ON
LEVEL LOW
DURATION S --|---- L
RET

Caution : If you use an infrared light source while in AUTO mode, AUTO

switching malfunction and camera AF malfunction may occur.

MOTION DET

In MOTION DET, you can set the Motion Detection function, Motion Detection
Sensitivity, and the Area of Motion Detection. If the Motion Detection function
is set, the movement of an intruder can be detected. When motion is detected,
it sets off the Alarm signal of the Controller.

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW
MOTION DET ON...
ZOOM SPEED 3
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

COLOR

...

➜

Press

[Enter]

(MOTION DET)

AREA USER...
SENSITIVITY
RET

L ---|--- H

E

3-6

3-7

Select ON and press [Enter ] to display an additional menu window of
“MOTION DET ”.
You can select one from the sub items of TOP..., BOTTOM..., LEFT...,
RIGHT..., CENTER... or USER... as AREA where the Motion Detection
function is applied.Select one from TOP..., BOTTOM..., LEFT..., RIGHT...,
CENTER... or USER... and press [Enter ]. You ’ll see the factory defaults of
that item and Motion Detection will be applied to the area you selected.
If you set the AREA menu to USER and press [ENTER], you may vary the size
and position of the area where you want to apply the MOTION detection
function by yourself. Press Left, Right, Up, or Down to select an area AREA.
Press ENTER and then Left, Right, Up, or Down to select a LOCATION. Press
ENTER again to move back to the upper menu.
Use [ENTER] and Left, Right, Up, or Down to move and scale the MOTION
detection area.
Press [ENTER] again and you will escape the AREA setup menu.
Use SENSITIVITY to set up the sensitivity of MOTION detection strength.
The higher, the more sensitive.

DIGITAL ZOOM

You may set up the digital zoom magnification ratio in the DIGITAL ZOOM
menu. The magnification ratio ranges from OFF to 10. If you set Digital
Zoom of SCC-C6403 to max. 10 times, the mode will become the 32 time
optical zoom and you will be able to enlarge a subject by max. 320 times.
Use Left or Right to select a magnification ratio in the DIGITAL ZOOM menu.

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW BW...
MOTION DET OFF
ZOOM SPEED 3
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

➜

Use the

[Left, Right]

Keys

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW BW...
MOTION DET OFF
ZOOM SPEED 3
DIGITAL ZOOM X10
DISPLAY ZOOM OFF
DISPLAY P/T OFF

EXIT QUIT

E

AREA

AREA

➜

Use the

[Left, Right, Up, Down]

LOCATION

After PAN/TILT/ZOOM/FOCUS/IRIS movement finishes, MOTION DET function

❈

will not work for about 5 seconds to stablize the chage of the screen.

❈

MOTION detection function operates based on the brightness change within the
setup region. Therefore, erroneous operation may occur depending on the
brightness difference between the background and the object that is being
taken, or the status of the area setup, etc.

ZOOM SPEED

In the ZOOM SPEED menu you can select the speed of the ZOOM Key
(Tele/Wide).
Use the [Left] or [Right] keys in the ZOOM SPEED menu to select
the speed.
1 : Slowest speed
2 : Low speed
3 : High speed
4 : Fastest speed

Keys

LOCATION

DISPLAY ZOOM

In DISPLAY ZOOM, you can display the ZOOM scale on the screen.

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW
MOTION DET OFF
ZOOM SPEED 4
DIGITAL ZOOM OFF
DISPLAY ZOOM ON
DISPLAY P/T OFF

EXIT SAVE

COLOR

...

X020

❈ If no change on the ZOOM scale is made for 3 seconds, the information window will

disappear.

DISPLAY P/T

In DISPLAY P/T, you can display the position of Pan/Tilt on the screen.

(CAMERA SET)

CAMERA ID OFF
V-SYNC INT
COLOR/BW
MOTION DET OFF
ZOOM SPEED 4
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T ON

EXIT SAVE

COLOR

...

347/060

3-8

❈ If no change on the Pan/Tilt position is made for 3 seconds, the information window

will disappear.

❈ It allows an error range of ±2°.

3-9

EXIT

The EXIT menu is used to quit the CAMERA SET menu of the
SCC-C6403 and return to the MAIN MENU.

- QUIT : Ignores the changed information and restores the saved
information.

- SAVE : Saves the information of the setting condition of the menu.

- PRESET: Ignores the changed information and restores the initial
factory defaults of the menu.

2. VIDEO SET MENU

IRIS

There is a function to automatically adjust IRIS to the incoming light level.
Owing to this function, you may set up the brightness level yourself.
The ALC(Auto Light Control) menu allows you for video output level setup.

ALC

Choose the ALC of the IRIS item and press [ENTER] and set he submenu
to the Video Output level and BLC will be shown.The Video Output Level
can be set in the level item using the [Left, Right] keys.

BLC (Submenu of the ALC menu)

If you use a general camera to photograph a subject under backlight or
bright illumination, the subject will be shown dark on the monitor due to
the backlight. BLC(Back Light Compensation) is used to prevent such a
backlight problem to secure distinct images under bright illumination.
Using the [Left, Right] keys, you can set up BOTTOM…, TOP…, LEFT…,
RIGHT…, CENTER… 5 preset areas and the USER…function that can
directly set the areas. For example, for the items in the BLC menu, you
can confirm the preset BOTTOM area by pressing [ENTER] key in the
BOTTOM… status.

(VIDEO SET)

IRIS ALC...
SHUTTER
MOTION NORM
WHITE BAL ATW1
DIS --­FOCUS MODE ONEAF
SPECIAL ...

EXIT QUIT

(ALC)

AUTO X2...

➜

Press

[Enter]

(ALC)

BLC OFF
LEVEL (0)--- -I ----
RET

➜

Press

[Enter]

3-10

BLC BOTTOM...
LEVEL (0)----I---­RET

For items in the BLC menu, the user can set the size and location of the
BLC area by pressing [ENTER] key after put the cursor on USER… using
the [Left, Right] key. For SIZE items, you can use the [Up, Down, Left,
Right] key to designate the SIZE, and then press the [ENTER] key.
You can set the location for areas using the [Up, Down, Left, Right] key in
the LOCATION.

(ALC)

SIZE

➜

Press

BLC USER...
LEVEL (0) ----I---­RET

SIZE

[Enter]

LOCATION

SIZE

➜

Press

[Enter]

LOCATION

Use [Left, Right] key in the LEVEL menu to control the video output
level(brightness).

MANU

When you press [ENTER] key after selecting MANU in the IRIS item, an
additional screen appears in which you can set manually opening or closing
the IRIS.

(VIDEO SET)

IRIS MANU...
SHUTTER OFF
AGC OFF
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

➜

Press

[Enter]

LOCATION

(MANUAL)

LEVEL (00) ----I---­RET

E

3-11

SHUTTER

You may designate both the fast electronic shutter speed and low
electronic shutter speed in the SHUTTER menu. The fast electronic
shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to
be used for the bright and fast video image. The AUTO slow electronic
shutter supports 12 shutter speeds from x2 to x160 and sets the shutter
speed to be slow In order to make the image on the screen more distinct
and brighter when you photograph under dark illumination. If you want to
sense the light brightness to control the shutter speed to the brightness
automatically, select the AUTO slow shutter.

(VIDEO SET)

IRIS ALC...
SHUTTER OFF
AGC
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

Keep pressing both Left and Right in the SHUTTER menu, the speed will
change in the following sequence.

➝ OFF ➝ AUTO X2... ➝ AUTO X4... ➝ AUTO X6... ➝ AUTO X8... ➝ AUTO X12... ➝
AUTO X16... ➝ AUTO X24... ➝ AUTO X32... ➝ AUTO X48... ➝ AUTO X64... ➝
AUTOX96... ➝ AUTO X128... ➝ OFF ➝ 1/100(1/120) ➝ 1/250 ➝ 1/500 ➝ 1/1000 ➝
1/2000 ➝ 1/4000 ➝ 1/10K

❈

If you set SHUTTER to between AUTO X4... and AUTO X128..., FOCUS mode will be displayed
as “MF“ (the product can operate only in MF mode). You can ’t adjust the settings manually.
If you set it to OFF, 1/100(1/120)/10K or AUTO X2..., the product will recover the previous
FOCUS mode.

❈

If you set SHUTTER to between AUTO X2... and AUTO X128..., DIS will be displayed as
“---“ (it can only operate in Off mode). You can ’t adjust the settings manually.
If you set it to OFF or 1/100(1/120)/10K, the product will recover the previous settings of DIS.

FLICKERLESS

Either NTSC (for 50 Hz)or PAL (for 60 Hz areas)is an anti-flickering system that is
designed to avoid image flickering on the screen due to inconsistency between the
vertical synchronizing frequency of the picture and the flashing frequency of the
lightening. If you select and set AUTO to ON in SHUTTER from VIDEO SET, you can set
NTSC or PAL for your area and the auto shutter speed is fixed at 1/100(1/120) second.

(VIDEO SET)

IRIS ALC...

3-12

SHUTTER
MOTION NORM
WHITE BAL ATW1
DIS --­FOCUS MODE ONEAF
SPECIAL ...

EXIT QUIT

AUTOX2...

OFF

(FLICKERLESS)

➜

Press

[Enter]

FLICKERLESS OFF

RET

AGC

The AGC menu was designed to provide you with brighter screen
supposed you photographed any subject in the dark resulting in less
brighter image than regulated. AGC menu setup is available only when
the SHUTTER menu is set to Fast Shutter or Off. Press either Left and
Right to go to LOW or HIGH and the AGC function will be activated. LOW
is use to lower the maximum AGC GAIN and HIGH raise the maximum
AGC GAIN.

(VIDEO SET)

IRIS ALC...
SHUTTER OFF
AGC
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

❈

When the COLOR/BW menu of the camera set is set to AUTO..., AGC will

LOW

be displayed as “---“. You can’t adjust the settings manually.

MOTION

The MOTION function is available only when the SHUTTER men is set to
Slow Shutter AUTO, being composed of 5 steps, S.SLOW, SLOW,
NORM, FAST, F.FAST.

● S.SLOW reduces the amount of AGC as much as possible to monitor

subjects with no immobility in the dark.

● SLOW reduces the amount of AGC to monitor subjects with little

immobility in the dark.

●

NORM sets the amount of AGC to the middle to monitor mobile subjects in the dark.

● FAST raises the amount of AGC to monitor fast subjects in the dark.

● F.FAST reduces the amount of AGC as much as possible to monitor

very fast subjects in the dark.
When the SHUTTER menu is set to AUTO, press Down to locate the
cursor in the MOTION menu and press Left and Right for MOTION
function setup. Press Left to the SLOW side and Right to the FAST side.

(VIDEO SET)

IRIS ALC...
SHUTTER
MOTION
WHITE BAL ATW1
DIS --­FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

AUTO X2...
F.FAST

3-13

E

WHITE BAL

Lights are generally denoted as color temperatures and expressed in
Kelvin (
The general light color temperatures are shown below.

10000K

9000K

8000K

7000K

6000K

5000K

4000K

K

) units.

Blue sky

Rainy

Cloudy

Partly Cloudy

Sunny

Fluorescent lamp

You can select one of four modes for white balance adjustment as follows:

- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the
color temperature is monitored continuously and thereby white balance is
set automatically. The following are the approximate supported color
temperature ranges in these modes.

✻

ATW1 : 2500K ~ 9300K(
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(

✻

1. If the color temperature is out of this range in ATW1 mode, proper

1)

✻

2)

white balance may not be obtained. In that case, select ATW2 mode.

✻

2. In ATW2 mode, if one color is dominated in the shooted area, the
color can be displayed differently.
Therefore, select the mode which is appropriate for the environment.

- AWC(Auto-Tracing White Balance Control): In this mode, accurate white
balance is obtained by pressing [ENTER] while having a white paper in
front of the camera. White Balance data will be maintained after set it
once. AWC mode is best in locations where the color temperature of light
source is constant.

- MANU : If WHITE BAL menu is set to MANU mode, the user can set the
white Balance considering the current illumination. Select MANU item
and press [ENTER], the sub screen where you can select Manual White
Balance will be shown. Use the left/right keys to select 3200K, 5600K or
OFF(USER) mode in the PRESET menu.

K

- 3200

- 5600

: Set color temperature to 3200
: Set color temperature to 5600

K

K
K

- USER : Choose out a proper value from the RED and BLUE graph for
color and temperature setup.

E

3-14

3000K

2000K

1000K

Halogen lamp

Candlelight

Tungsten lamp

(VIDEO SET)

IRIS ALC...
SHUTTER
AGC
WHITE BAL MANU...
DIS ON
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

OFF
LOW

➜

Press

[Enter]

(AWB/MANU)

PRESET 3200K

RET

DIS

The DIS(Digital Image Stabilization) function compensates the camera
screen shaking incurred from vibration.

❈ It is recommended to deactivate the DIS function in the no vibration

environment.

❈

From VIDEO SET, if you set SHUTTER to between AUTO X2... and AUTO
X128... DIS will be displayed as “---“ (it can operate only in Off mode).
You can’t adjust the settings manually.

3-15

FOCUS MODE

In the FOCUS MODE MENU, the Focus method can be set to ONEAF
(One Auto Focus), or MF(Manual Focus).

- ONEAF : In the ONEAF mode, it automatically sets the focus after the
PAN/TILT/ZOOM moves, and operates as the same in the MF mode if the
PAN/TILT/ZOOM does not move.

- MF : In MANUAL FOCUS MODE the user adjusts the Focus manually.
Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.

(VIDEO SET)

IRIS ALC...
SHUTTER
AGC
WHITE BAL ATW1
DIS OFF
FOCUS MODE ONEAF
SPECIAL ...
EXIT QUIT

❈

ONEAF can only be selected if SHUTTER is set to OFF, 1/100(1/120)
~1/10K, or AUTOX2...
In other modes (AUTOX4...~AUTOX128...), FOCUS mode will be
displayed as “MF“(the product automatically switches into MF mode).You
can ’t adjust the settings manually.

❈

ONEAF function may not possible withe types of objects listed below. For
such objects, focus manually.

- High intensity objects or objects illuminated with low lighting

- Obejects shot through wet or dirty glass

- Pictures that are a mixture of distant and nearby objects

- White alls and other single-color objects

- Venetian blinds and other horizontally striped objects

SPECIAL

In SPECIAL menu, you can directly adjust Y-LEVEL, C-LEVEL, and DETAIL
functions.

- Y-LEVEL : It is used to set the levels for the Sync signal and the entire
brightness signal of the video signal.

- C-LEVEL : It is used to set the levels for the Burst signal and the entire colour
signal of the video signal.

- DETAIL : Controls both horizontal and vertical distinction.

OFF
OFF

EXIT

It's the same as the EXIT function of the CAMERA SET menu.

3. PRESET

This is the menu that user sets the PAN/TILT location, Zoom/Focus, and
screen condition, so the camera can monitor the presetting area on
demand. A total of 128 presets are available.

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET ...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

➜

Press

[Enter]

➜

Press

[Enter]

(PRESET MAP)

0 1 2 3 4

5 6 7 8 9
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31

î ï

ID:PRESET 0

PRESET NO.0

POSITION SET ...
PRESET ID ON...
VIDEO SET OFF
PRESET SPEED 8
DWELL TIME 3S
IMAGE HOLD OFF

EXIT QUIT

RET

E

3-16

(VIDEO SET)

IRIS ALC...
SHUTTER OFF
AGC ON
WHITE BAL ATW1
DIS ON
FOCUS MODE ONEAF
SPECIAL ...

EXIT QUIT

➜

Press

[Enter]

(SPECIAL)

Y-LEVEL (0)I-------­C-LEVEL (0)I-------­DETAIL (0)--I­RET

3-17

POSITION SET

From "POSITION SET..." press [ENTER] to get into the PAN/TILT,
FOCUS/ZOOM SET screen
to set the PAN/TILT location and FOCUS/ZOOM condition then press
[ENTER] to return to a higher menu.

4. ZONE SET

The ZONE SET menu includes the setup of ZONE DIRECTION, and
ZONE AREA.

PRESET ID

This is the ID set up function for each PRESET.
It can be set up to 12 characters using the left, right, up, and down keys.
The ID location can be set in the submenu of "LOCATION..."

VIDEO SET

This is the screen setting function for each PRESET.
Refer to the explanation under "VIDEO SET menu".

PRESET SPEED

This function sets up the speed of PAN or TILT by 8 steps from 1(SLOW)
to 8(FAST).

- PRESET SPEED 1 : Maximum PAN moving speed of 240°/sec

- PRESET SPEED 8 : Maximum PAN moving speed of 400°/sec

DWELL TIME

This is a function setting for the DWELL TIME of the PRESET location in

"SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.

IMAGE HOLD

Pauses the image when PRESET is in movement, If you set the IMAGE
HOLD menu to ON, the screen will be paused until PRESET finishes
moving.

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

➜

Press

[Enter]

(ZONE SET)

ZONE DIR SET OFF
ZONE AREA SET OFF

EXIT QUIT

ZONE DIR SET

Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the
SET NORTH screen. MAP. Move PAN to set the SET NORTH position
and press [ENTER]. Based on the North position,the direction of N(North),
NE(North-East), E(East), SE(South-East), S(South), SW(South-West),
W(West), NW(North-West) is displayed whenever you move PAN.

(ZONE SET)

ZONE DIR SET ON...
ZONE AREA SET OFF

EXIT QUIT

➜

Press

[Enter]

SET NORTH

N

E

EXIT

"QUIT" : Does not save the selected information and returns to a higher

menu.
"SAVE" : Do saves the selected information and returns to a higher menu.
"DEL" : Deletes the selected information and restores the DEFAULT.

Then returns to a higher menu.

3-18

3-19

ZONE AREA

Press [ENTER] to enter the ZONE AREA MAP screen from “ZONE
AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP
screen and press [ENTER] to enter the ZONE AREA setup screen.

LOCATION

The “LOCATION...” menu designates the left/right LIMIT positions of
ZONE AREA. Enter the setup screen to move PAN, then select a start
position and press [ENTER]. Move PAN again
to select a end position and press [ENTER]. Now, ZONE AREA setup is
complete.

(ZONE SET)

ZONE DIR SET OFF
ZONE AREA SET ON...

EXIT QUIT

➜

Press

[Enter]

➜

Press

[Enter]

ZONE AREA SET 0

LOCATION ...
ZONE ID SET ...
ZONE ENABLE ON

EXIT QUIT

(ZONE AREA MAP)

0 *1 2 3
4 5 6 7

ZONE AREA SET 0

LOCATION ...
ZONE ID SET ...
ZONE ENABLE ON

EXIT QUIT

SET END!

➜

Press

[Enter]

SET START!

➜

After P/R/Z

control, press

[ENTER]

After PAN control,

press [ENTER] to

finish.

ZONE ID SET

This function is used to allocate as many as 12 IDs to each zone area.
Use Left , Right, UP, or DOWN for this purpose. You may select the ID
position from the additional menu of “LOCATION...”.

ZONE AREA SET 0

LOCATION ...
ZONE ID SET ...
ZONE ENABLE ON

EXIT QUIT

➜

Press

[Enter]

ZONE AREA ID 0

A B C D E F G H I J K L
M N O P Q R S T U V W X
Y Z 0 1 2 3 4 5 6 7 8 9

SP
LOCATION...

RET

ZONE 0........

: ! - +

ï î

✻

SP

()/

E

3-20

ZONE ENABLE

This function turns on or off the ZONE AREA ID indication.

3-21

5. AUTO SET

The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is
able to set up the AUTO PLAY motion.

AUTO PAN

After selecting the locations of two points (PAN/TILT) of START and END,
it loops continuously in the set up SPEED. The number of AUTO PAN is
up to 4.

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

➜

Press

[Enter]

➜

Press

[Enter]

(AUTO SET)

AUTO PAN 1...
PATTERN 1...
SCAN 1...
AUTO PLAY ...

RET

AUTO PAN 1

POSITION SET ...
SPEED 22
DWELL TIME 3S

EXIT QUIT

SPEED

This is a setting function for movement speed setup. It can be set from
STEP1 to STEP64.

DWELL TIME

This is a function for setting up the time to stay in the START to END position.

PATTERN

This is a replay function so that the MANUAL functions such as PAN, TILT,
ZOOM, and FOCUS, IRIS are played for 2 minutes.

❈ When the PATTERN is saved/executed, the PAN/TILT is operated with

PROPORTIONAL ON, TURBO OFF.

❈ If the SSC-1000 or SSC-2000 is used when uploading/downloading the

menu setup, reset the PATTERN because it may be different with the first
setting.

E

POSITION SET

The menu “POSITION SET …” sets the Start / End position of AUTO PAN.
Return to the settings screen and set the desired START position for
PAN/TILT, and then press the [ENTER] key. And, set the END position for
the PAN/TILT. Press the [ENTER] key to finish the setup for AUTO PAN
Start/End positions.

3-22

3-23

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

PATTERN SET 1

SET START POSITION
AND ENTER

➜

Press

[Enter]

➜

After

PATTERN

(AUTO SET)

AUTO PAN 1...
PATTERN 1...
SCAN 1...
AUTO PLAY ...

RET

PATTERN SET 1

➜

Press

[Enter]

START

position setup,

press

[ENTER].

PATTERN can be set upto 3. Choose 1, 2, or 3 with the left or right key in the
"PATTERN SET" and press [ENTER] to get into the PATTERN set up screen. From
the moment "PATTERN 1 SET" is gone for 2 minutes, it memorizes the MANUAL
movements and after 2 minutes it will return to a higher menu. If you want to finish
set up before the 2-minutes ends, press [ENTER].

SCAN

SCAN sets the direction of PRESET movement during “SCAN” operation. The
number of SCAN is up to 4 and each SCAN is able to allocate 32 PRESETs as a
maximum.

AUTO PLAY

AUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when there
is no camera action after AUTO RETURN finishes.

(AUTO SET)

AUTO PAN 1...
PATTERN 1...
SCAN 1...
AUTO PLAY ...

RET

➜

Press

[Enter]

(AUTO PLAY SET)

AUTO RETURN 12HOUR
AUTO PLAY SCAN
PLAY NUMBER 1

EXIT SAVE

AUTO RETURN

This menu sets up the time during which AUTO PLAY repeats.

AUTO PLAY

This function sets up the motion which will be repeatedly performed by
SCC-C6403 whenever the time set by AUTO RETURN elapses. It covers SCAN,
AUTO PAN, PATTERN, and PRESET setup.

PLAY NUMBER

This menu allocates a number to the motion set by AUTO PLAY. The numbers
range from 1 to 4 for SCAN AND AUTO PAN, 1 to 3 for PATTERN, and 0 to 127
for PRESET.

E

(AUTO SET)

AUTO PAN 1...
PATTERN 1...
SCAN 1...
AUTO PLAY ...

RET

➜

Press

[Enter]

(SCAN MAP 1)

0*S 1* 2 3 4

5 6 7 8 9
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31

î ï

EXIT SAVE

If you enter the SCAN SET screen, SCAN MAP will be displayed. Move the cursor
to the number marked * where PRESET is saved and press [ENTER] and
S will appear and a PRESET will be included in SCAN.

3-24

3-25

6. ALARM SET

It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an
ALARM input from exterior SENSORs and it performs with PRESET or
PATTERN function and outputs the ALARM OUT signals.
Alarm operation time depends on the Preset Dwell time corresponding to
the alarm and whether AUTO is involved.

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

➜

Press

[Enter]

ALARM PRIORITY SET

This sets the priority of the 4 ALARM inputs so ALARM can work
corresponding to the priority.
The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4.
If the ALARM is working at the same time and the priority is the same, it
will operate according to the DEFAULT priority. While the ALARM is
working, it cannot detect MOTION.

( ALARM SET)

ALARM PRIORITY SET ...

ALARM IN SET..

ALARM OUT SET..

AUTO SET..

AUX OUT CONTROL..

RET

AUTO SET

This menu designates what to do at the time of ALARM input. Once an
alarm is given, the camera will shortly move to the PRESET position
corresponding to the respective alarm as follows.
PRESET1 to ALARM1~4
PRESET5 to MOTION
After DWELL TIME at a PRESET position, PATTERN or SCAN will be in
action according to the AUTO SET setup.
Setup of OFF/PATTERN 1~3/HALF1/HALF2/FULL/SCAN1~4 is available.
OFF dues not perform PATTERN or SCAN after moved to PRESET and
each menu has its own function as follows.
PATTERN 1~3 : Preset PATTERN action,
HALF1 : Continuous operation of PATTERN1 + PATTERN2
HALF2 : Continuous operation of PATTERN2 + PATTERN3
FULL : Continuous operation of all the aboves
SCAN 1~4 : Scanning as set

AUX OUT CONTROL

This sets the ALARM OUT motion to continue or act only when the
ALARM is working.
If it is set to OFF the ALARM OUT motion will operate only when the
ALARM is working.
(Active "Low"), and if it's set to ON, the ALARM OUT will always operate
regardless of the ALARM.

E

ALARM IN SET

This sets the input TYPE to "NO" (Normal Open), "NC" (Normal Close), or
"OFF" depending on the features of the SENSOR connected.

ALARM OUT SET

Each ALARM input corresponds to one of the 3 ALARM OUT.

3-26

7. OTHER SET

PROPORTIONAL P/T

This function controls the PAN/TILT speed to the ZOOM magnification
ratio during the manual operation of PAN/TILT. If you set
PROPORTIONAL P/T to ON, the PAN/TILT speed will increase in the
ZOOM WIDE mode and decrease in the ZOON TELE mode even in the
same manual operation.

3-27

TURBO P/T

This function doubles up the speed of PAN/TILT movement by manual
operation of PAN/TILT. The speed may go up to 180°/sec(PAN).

AUTO CAL

This function turns on or off Auto Calibration. SCC-C6403 has the Auto
Calibration function to improve the precision of LENS and PAN/TILT
motor. You may set to OFF/6H/12H/18H/24H. Without user’s key input for
the time designated by the user, A.C will appear on the screen while
initializing LENS and PAN/TILT.

AUTO FLIP

When TILT is set to a 90° limit using the joystick, PAN automatically
rotates by 180°
enabling you to see up to the Tilt area on the opposite side .
You can obtain an extended effect with the 180° operational range of the
TILT feature.

CAM RESET

CAM RESET clears all the settings made so far and restores the factory
default settings.
"CAMERA RESET?" message appears when you select CAM RESET.
Select "CANCEL" to return to the menu setup display or select OK to
restore the factory default settings.

❈ Be careful when performing a CAM RESET operation, as it deletes all

setup values.

(OTHER SET)
PROPORTIONAL P/T ON

TURBO P/T OFF
AUTO CAL. OFF
AUTO FLIP ON
CAM RESET ...
LANGUAGE ENGLISH
PASSWORD ON...

EXIT QUIT

➜

Press

[Enter]

(PASSWORD)

0 1 2 3 4
5 6 7 8 9

✽ ✽ ✽ ✽

✽ ✽ ✽ ✽

RET

Press UP/DOWN/LEFT/RIGHT key to locate the cursor on a number and
press [ENTER] for password setup. After you finish inputting the 4 digits
password and the 2nd row of the 4 digits PASSWORD input screen, input
the selected password again for reassurance.
If correct, the cursor will move to RET.
Press [ENTER] at RET, and the selected password will be saved,
returning to the OTHER SET screen.
Default password is 0123.

8. SYSTEM INFO

This menu allows you to check S/W version, communication protocol,
baud rate, and address of SCC-C6403.

** MAIN MENU **

CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...

➜

Press

[Enter]

( SYSTEM INFO)

ALARM VER. V1.000
MOTOR VER. V1.000
CAMERA VER. V1.000
EEPROM VER. V1.000
PROTOCOL SAMSUNG
COMM. TYPE RS-485,HALF
BAUD RATE 9600
ADDRESS 0
SERIAL NO.
RET

000000000000000

E

LANGUAGE

This function selects a language for MENU setup. Press LEFT/RIGHT key to
choose English, French, Spanish or Jepanese and the selected
language will be applied to the full screen.

PASSWORD

This function selects or cancels the MENU setup password. Press
[ENTER] at the state of PASSWORD ON..., and the following screen will
appear for password setup.

3-28

3-29

9. SHORT KEYS

SSC-1000 or SSC-2000 Controller supports the following short keys.

Function Key

CAMERA SET…

COLOR/BW COLOR
COLOR/BW BW
COLOR/BW AUTO

VIDEO SET…

IRIS ALC
FOCUS MODE MF
FOUCS MODE ONEAF

ALARM SET…
AUX OUT CONTROL…

OUT1 ON
OUT1 OFF
OUT2 ON
OUT2 OFF
OUT3 ON
OUT3 OFF

OTHER SET…

PROPORTIONAL P/T ON
PROPORTIONAL P/T OFF
TURBO P/T ON
TURBO P/T OFF
AUTO FLIP ON
AUTO FLIP OFF

AUTO RETURN *1)
AUTO CAL.
CAM RESET

[PRESET] + [1] + [2] + [8] + [Enter]
[PRESET] + [1] + [2] + [9] + [Enter]
[PRESET] + [1] + [3] + [0] + [Enter]

[PRESET] + [1] + [3] + [2] + [Enter]
[PRESET] + [1] + [3] + [4] + [Enter]
[PRESET] + [1] + [3] + [5] + [Enter]

[PRESET] + [1] + [3] + [6] + [Enter]
[PRESET] + [1] + [3] + [7] + [Enter]
[PRESET] + [1] + [3] + [8] + [Enter]
[PRESET] + [1] + [3] + [9] + [Enter]
[PRESET] + [1] + [4] + [0] + [Enter]
[PRESET] + [1] + [4] + [1] + [Enter]

[PRESET] + [1] + [4] + [2] + [Enter]
[PRESET] + [1] + [4] + [3] + [Enter]
[PRESET] + [1] + [4] + [4] + [Enter]
[PRESET] + [1] + [4] + [5] + [Enter]
[PRESET] + [1] + [4] + [6] + [Enter]
[PRESET] + [1] + [4] + [7] + [Enter]

[PRESET] + [1] + [4] + [8] + [Enter]

[PRESET] + [1] + [4] + [9] + [Enter]

[PRESET] + [1] + [5] + [0] + [Enter]

❈ SCC-C6403 has two FANs inside for preventing overheating.

If FAN doesn't work properly, messages below will be displayed.
In those case, replace the FAN.

- ALARM FAN ERROR !
: This message is displayed when the FAN which is located bottom of

SCC-C6403 does not work properly.

Contact your nearest Samsung Electronics Service Center or designated

retailer before replacing the FAN.

E

Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall
be applied to the MENU setup process.

1) The use of AUTO RETURN will be available only when the function
equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in.

3-30

3-31

Product specifications

SCC-C6403

NO

1
2
3
4
5
6
7

8

9
10
11

12

13

14

15

16

17

18

19

20
21

22

23

24

Items

Product Type

Power Input

Power Consumption

Broadcasting Type

Image Device

Effective Pixels

Scanning Mode

Scanning line

Frequency

Synchronization Mode

Resolution

S/N Ratio

Min. Object Illumination

Color Temperature

Signal Output

Lens

PAN Function

TILT Function

REMOTE

CONTROL

ALARM

Operation Temperature

Operation Humidity

SIZE

Weight

Lives of Main Parts

- Zoom lens single body SmartDome CAMERA

- AC 24 ± 10% (50Hz ± 0.3Hz)

- 18W

- NTSC STANDARD COLOR SYSTEM

- 1/4 inch 410K IT Type S-HAD CCD

- 768(H) X 494(V)

- 525 Lines, 2:1 Interlace

- Horizontal : 15,734 Hz(INT) / 15,750 Hz(L/L)

- Vertical : 59.94 Hz(INT) / 60 Hz(L/L)

- INT/LINE LOCK

- 480 TV LINES

- 50dB (AGC OFF)

- COLOR : 0.3 Lux (30 IRE : Sense-Upx4)

0.01 Lux (30 IRE : Sense-Up x128)

- B/W : 0.03 Lux (30 IRE : Sense-Upx4)

0.001 Lux (30 IRE : Sense-Up x128)

- ATW1/ATW2/AWC/MANUAL MODE
(3200K, 5600K, R/B

-

COMPOSITE VIDEO OUT : 1.0Vp-p 75ohms/BNC

- one body; 32x Zoom lens

- Focal Length : 3.55 to 113 mm

- Aperture : F1.69(Wide), F4.17(Tele)

- MOD(Minimum Object Distance) : 2.5m

- PAN range : 350° Non-Endless

- Preset Pan Speed : max 400°/sec

- Manual Pan Speed : 0.1°~180°/sec (64step)

- TILT range : 0°~90°

- Preset TILT Speed : max 200°/sec

- Manual TILT Speed : 0.1°~90°/sec (64step)

- ZOOM(TELE/WIDE), FOCUS(NEAR/FAR),
IRIS(OPEN/CLOSE), PAN/TILT, MENU
RS-485 HALF/FULL Duplex, RS-422

- Alarm Inputs : 4 IN(5mA Sink)

- Alarm Outputs : 3 OUT (Open collector : 2
DC24V 40mA Max, Relay : 1, NO, NC, COM
2A 30VDC, 0.5A 125VAC Max)

- 10°C ~ +50°C

- ~90%

- DOME : 147 (

- Outline : 159.6(

- 1.8Kg

- FAN

Contents

ø),

ø) X 177(H)

GAIN Court)

Remark

4.5 Years

Cautions

• The copyright of the manual belongs to Samsung Electronics Co., Ltd.
Without the permission of Samsung Electronics it cannot be reproduced

•

electronically, mechanically, audibly, or by any other method.

•

This manual will be modified according to product enhancements.

3-32