SCC-C6323P
SCC-C6325P
SCC-C7325P
10x Mini Smart
Dome Camera
user manual
ENG |
FRE |
GER |
SPA |
ITA |
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service,
please register your product at
www.samsungsecurity.com
Safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..
This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
WARNING
•To prevent damage which may result in fi re or electric shock hazard, do not expose this appliance to rain or moisture.
WARNING
1.Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet. Using any other adapter could cause fi re, electrical shock, or damage to the product
2.Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or damage to the product.
3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fi re.
4.Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.
5.When installing the camera, fasten it securely and fi rmly. A falling camera may cause personal injury.
6.Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers fi lled with water on top of the camera. Doing so may cause personal injury due to fi re, electric shock, or falling objects.
7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.
8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.
9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.)
10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.
11.If the camera is installed or rebooted after power failure when ambient temperature is below the freezing point, the dome cover is frosted. In this case, the frost will be disappeared after 3 hours after turning on the power. (It is noted that lowest guaranteed operating temperature is -45º C (-49º F) without wind.)
2 – 10X MINI SMART DOME CAMERA
Safety information
CAUTION
1. |
Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to |
|
|
excessive vibrationor magnetic interference. |
|
2. |
Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high |
|
|
humidity. Doing so may cause fi re or electric shock. |
|
3. |
If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall |
|
|
it. |
|
4. |
Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fi re or |
|
|
damage to the product. |
|
5. |
Keep out of direct sunlight and heat radiation sources. It may cause fi re. |
|
6. |
Install it in a place with good ventilation. |
|
7. |
Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the |
|
|
CCD image sensor. |
|
8. |
Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, |
|
|
shall be placed on the apparatus. |
|
9. |
The Mains plug is used as a disconnect device and shall stay readily operable at any time. |
ENG |
|
|
|
|
|
|
English – 3
Important Safety Instructions
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/accessories specifi ed by the manufacturer.
12.Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus.
13.Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
14.Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
4 – 10X MINI SMART DOME CAMERA
Contents
Introduction |
|
|
Features |
|
7 |
Product & Accessories |
|
8 |
Parts Name & Functions |
|
10 |
Installation |
|
|
DIP Switch Setup |
|
13 |
Installation using Surface mount on the Ceiling |
|
14 |
Installation using Ceiling Mount Bracket (SCC-C7325) |
|
16 |
Installation using Wall Mount Bracket (SCC-C7325) |
|
17 |
Cabling |
|
19 |
Operation |
|
ENG |
|
Check points before operation |
21 |
||
|
|||
Preset and Pattern Function Pre-Check |
21 |
|
|
Starting OSD Menu |
21 |
|
|
Reserved Preset |
21 |
|
|
Preset |
22 |
|
|
Auto Pan |
22 |
|
|
Pattern |
22 |
|
|
Scan |
23 |
|
|
Schedule |
23 |
|
|
Other Functions |
23 |
|
|
OSD Display of Main Screen |
24 |
|
|
General Rules of Key Operation for Menu |
25 |
|
|
Main Menu |
25 |
|
|
System Information |
25 |
|
|
Display Setup |
25 |
|
English – 5
Contents
How to use OSD Menu
Privacy Zone Mask Setup |
|
26 |
Motion Setup |
|
26 |
Function Setup |
|
27 |
PRESET Setup |
|
28 |
Auto Pan Setup |
|
29 |
Pattern Setup |
|
30 |
Scan Setup |
|
30 |
Schedule Setup |
|
32 |
Camera Setup |
|
33 |
System Setup |
|
34 |
System Initialize |
|
36 |
Specifications
Specifi cations |
|
38 |
Dimension |
|
41 |
6 – 10X MINI SMART DOME CAMERA
Introduction
FEATURES
Camera Specifications
• |
CCD Sensor |
: 1/4” |
Interline Transfer CCD |
• Zoom Magnifi cation |
: x10 |
Optical Zoom, x10 |
|
|
Digital Zoom (Max x 100 Zoom) |
•7 rules of Schedule can be assigned by day and time. Appropriate actions (such as Home, Preset, Auto Pan, Pattern, Scan) can be defi ned for each rule. Also, it is possible to make rule by Weekday and Allday to simplify the rule.
•Day & Night Function
•Various Focus Mode: Auto-Focus / Manual Focus / Semi-Auto Focus.
•Independent or General Camera Characteristic Setup in Preset operation
Powerful Pan/Tilt Functions
•Max. 360°/sec high speed Pan/Tilt Motion
•Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to target view is reduced dramatically and the video on the monitor is very natural to watch.
•For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy to locate camera to desired target view.
•Owing to zoom-proportional pan/tilt speed, camera can be moved to a desired position in accurate manner even though zoom ratio is high.
PTZ(Pan/Tilt/Zoom) Control |
|
• With RS-485 communication, max. 255 of |
|
cameras can be controlled at the same time. |
|
• Pelco-D/ Pelco-P, Samsung protocol can be |
|
selected as a control protocol in the current |
|
version of fi rmware. |
|
OSD(On Screen Display) Menu |
|
• OSD menu is provided to display the status |
|
of camera and to confi gure the functions |
|
interactively. |
|
• Currently, 7 Languages are supported for |
|
OSD Menu: [ENGLISH/ESPAÑOL/FRANÇAIS/ |
|
DEUTSCH/ITALIANO/РУССКИЙ/PORTUGUÊS] |
|
• The information such as Camera ID, Pan/Tilt/ |
ENG |
Zoom/Direction, Alarm Input & Output, date/time, |
|
current temperature and Preset can be displayed |
|
on screen. |
|
• Each display item can be turned On or Off |
|
independently. |
|
Preset, Pattern, Auto Pan, Scan, Privacy Mask, Schedule and More…
•MAX. 127 Presets are assignable and characteristics of each preset can be set up independently, such as White Balance, Auto Exposure, Label and so on.
•Max. 8 Auto Pan can be stored. This enables to move camera repetitively between two preset positions with designated speed.
•Max. 4 of Patterns can be recorded and executed. This enables for camera to track a surveillance trajectory as closely as possible which are recorded from operator’s motion of joystick.
•Max. 8 Scan can be stored. To compose a surveillance trajectory, the Group can have max. 20 entities of Preset/Pattern/Scan functions. This enables for camera to move a combinations of those functions repetitively.
•Max. 4 Masks are settable independently to protect privacy zone. The mask is arbitrary-sized rectangular and locate any location in view space.
Alarm I/O Functions
•2 alarm sensor Inputs and 1 relay output are available.
•To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo coupler.
•If an external sensor is activated, camera can be set to move to the corresponding Preset position.
•Relay output can be assigned to work with a certain preset.
Reserved Presets for Special Purpose
•Besides regular 127 presets, direct calling of reserved presets enables to set up many of camera functions with without using OSD menu. For more information, refer to “Reserved Preset” in this manual.
English – 7
Introduction
PRODUCT & ACCESSORIES
Product & Accessories (SCC-C6323)
• Main Product
Main Body |
Surface Mount Bracket |
• Accessory
G
Manual |
Screw & Plastic Anchor (4Pcs) |
Core filter (PAL Option) |
Product & Accessories (SCC-C6325)
• Main Product
Main Body |
Surface Mount Bracket |
• Accessory
Screw & Plastic |
Terminal Block |
Torx Screw Driver |
Surface Mount |
Manual |
Anchor (4Pcs) |
|
|
Gasket |
|
Ú Mount Bracket Option : Please use SADT-937WM for this purpose.
8 – 10X MINI SMART DOME CAMERA
Introduction
Product & Accessories (SCC-C7325)
• Main Product
Main Body |
Sun Shield Housing |
• Accessory
ENG |
Terminal Block |
Torx Screw Driver |
Manual |
• Mount Bracket Option |
|
|
Wall Mount Bracket (SADT-732WM) |
Ceiling Mount Bracket (SADT-732CM) |
English – 9
Introduction
PARTS NAME & FUNCTIONS
SCC-C6323
Surface Mount Bracket
Separating Slit
Dome Cover
Main Unit / Surface Mount Bracket
•Surface Mount Bracket
This is used to install the camera directly on the ceiling. After separating this cover fi rst and then attach this directly to ceiling. Camera must be assembled at the last stage.
Do not use this bracket when installing camera on the wall with wall mount bracket or on the ceiling with ceiling mount bracket.
•Separating Slit
Using a coin, you can separate upper part lower body of the dome.
DIP Switch
Cable Duct
Back of Main Unit
•Dome Cover
Do not detach protection vinyl from dome cover before fi nishing all installation process to protect dome cover from scratches or dust.
•DIP Switch
Adjusts camera ID and protocols.
•Cable Duct
When you want to install the camera on the surface of hard ceiling, you need to handle the cable through side of the dome. In this case, break the side wall bit and make the cable pass through the cable duct.
10 – 10X MINI SMART DOME CAMERA
Introduction
SCC-C6325
Surface Mount Bracket
Mounting Hole
Main Body
Lockup Screw
Dome Cover
Main Unit / Surface Mount Bracket
•Dome Cover
Do not remove the protection vinyl from dome cover before fi nishing all installation process to protect dome cover from scratches or dust.
•Surface Mount Bracket
This is used to install the camera directly on the ceiling. After separating this cover, mount this bracket on to ceiling. Main body of the camera is going to be assembled again in the last stage.
Do not use this bracket with wall mount bracket or ceiling mount bracket.
Back of Main Unit
• Lockup Screw
Cabling Terminal
Block
DIP Switch
ENG |
Fixes main unit brackets like surface, wall, and ceiling.
•Cabling Terminal Block
During installation, Power, Video, Communication, Alarm Input cables are connected on to this cabling terminal block.
•DIP Switch
Adjusts camera ID and protocols.
English – 11
Introduction
PARTS NAME & FUNCTIONS
SCC-C7325
Sun Shield Housing
Main Body
Lockup Screw
Dome Cover
Main Unit / Surface Mount Bracket
•Dome Cover
Do not remove the protection vinyl from dome cover before fi nishing all installation process to protect dome cover from scratches or dust.
•Sun Shield Housing
•Lockup Screw
Fixes main unit brackets like surface, wall, and ceiling.
Cabling Terminal
Block
DIP Switch
Back of Main Unit
•Cabling Terminal Block
During installation, Power, Video, Communication, Alarm Input cables are connected on to this cabling terminal block.
•DIP Switch
Adjusts camera ID and protocols.
12 – 10X MINI SMART DOME CAMERA
Installation
DIP SWITCH SETUP
•Select the appropriate Protocol with DIP switch combination.
Before you install the camera, you should set the DIP switches to confi gure the camera ID, Baud rate, and communication protocol.
Protocol |
Buad Rate |
Auto Select |
|
|
Switch State |
|
Protocol |
|
|
|
|
|
|
Pin1 |
Pin2 |
Pin3 |
Pin4 |
|
|
|
|
|
|
OFF |
OFF |
OFF |
OFF |
Auto Protocol |
ON |
OFF |
OFF |
OFF |
Pelco-D |
OFF |
ON |
OFF |
OFF |
Pelco-P |
ON |
ON |
OFF |
OFF |
Samsung |
ID Setting (1~255)
Camera ID Setup
• If you set the protocol as Auto Protocol, camera will automatically recognize the kind of Protocol.
RS-485 |
• |
Auto Protocol supports Pelco-D and Samsung Protocol. |
|
• |
If you want to control using DVR or system |
||
Terminate |
|||
|
keyboard, their protocol must be identical to |
||
|
|
||
|
|
camera. Otherwise, you can not control the camera. |
• If you changed camera protocol by changing DIP S/W, |
||||||||
the change will be effective after you reboot the camera. |
||||||||
• Factory default of protocol is “Auto Protocol |
||||||||
Communication Baud rate Setup |
ENG |
|||||||
|
|
|
|
|
|
|
|
|
ON |
ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
•ID number of camera is set using binary number. The example is shown bellow.
Pin |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
|
|
|
|
|
|
|
|
|
ID Value |
1 |
2 |
4 |
8 |
16 |
32 |
64 |
128 |
|
|
|
|
|
|
|
|
|
ex) ID=5 |
on |
off |
on |
off |
off |
off |
off |
off |
ex) ID=10 |
off |
on |
off |
on |
off |
off |
off |
off |
|
|
|
|
|
|
|
|
|
•The range of ID is 0~255. Factory default of Camera ID is 1.
•If you want to control a certain camera, you must match the camera ID with Cam ID setting of DVR or Controller.
Communication Protocol Setup
ON ON
•Select the appropriate Baud rate with DIP switch combination.
|
Switch State |
|
Protocol |
||
|
|
|
|
|
|
Pin5 |
|
Pin6 |
|
Pin7 |
|
|
|
|
|
|
|
OFF |
|
OFF |
|
OFF |
2400 BPS |
ON |
|
OFF |
|
OFF |
4800 BPS |
OFF |
|
ON |
|
OFF |
9600 BPS |
ON |
|
ON |
|
OFF |
19200 BPS |
OFF |
|
OFF |
|
ON |
38400 BPS |
• Factory default of Baud rate is “9600 BPS”
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
English – 13
Installation
RS-485 Termination Resistor
ON
ON
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
•Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of last camera.
– Pin 8 RS-485 Termination Resistor (On/Off)
INSTALLATION USING SURFACE MOUNT ON THE CEILING
SCC-C6323
Setup DIP Switch (see previous page).
Screw surface mount bracket to ceiling with 4 screws.
Placing lower body to Surface Mount bracket. The cable must be properly handled into hole of bracket or side of lower body.
Make sure stopper pin of bracket pin is located the rightmost side of lower body groove as shown in the picture. Press the dome and turn clockwise till the pin is located leftmost side
of groove. Detach protection vinyl from dome cover.
G
14 – 10X MINI SMART DOME CAMERA
Installation
Tighten locking screw. |
SCC-C6325 |
Connect Video, communication, power cable properly. (see next section)
To pass cables to upside of ceiling, please, make about ũ60mm hole on the ceiling panel.
Screw surface mount bracket to ceiling with 4 screws.
ENG |
Wire cables to terminal block and connect the terminal blocks to main unit.
English – 15
Installation
Screw main unit to surface mount bracket with 4 lock-up screws.
Detach protection vinyl from dome cover.
INSTALLATION USING CEILING MOUNT BRACKET (SCC-C7325)
Install ceiling mount bracket on the ceiling using 4 screws provided.
Turn sunshield clockwise after locating it in the pipe head of ceiling mount properly.
16 – 10X MINI SMART DOME CAMERA
Installation
After wiring cables to terminals, plug the terminals into the bottom of main unit. Then, fi x the main unit with sunshield with 4 screws.
INSTALLATION USING WALL MOUNT BRACKET (SCC-C7325)
Use the 4 screws (provided) to secure the wall mount bracket to the wall.
Turn sunshield clockwise after locating it in the |
ENG |
pipe head of wall mount properly. |
Detach protection vinyl from dome cover.
English – 17
Installation
After wiring cables to terminals, plug the terminals into the bottom of main unit. Then, fi x the main unit with sunshield with 4 screws.
Detach protection vinyl from dome cover.
18 – 10X MINI SMART DOME CAMERA
Installation
CABLING
SCC-C6323
Dual Voltage
DC 12V/AC 24V
BNC Video
|
|
Controller/DVR |
|
1 |
(Black) : IN COM |
|
IrDA |
|
Sensor |
||
2 |
(Yellow) : IN 1 |
|
Door |
3 |
(Brown) : IN 2 |
|
|
|
Switch |
||
4 |
(Red) : Relay Out |
Sensors |
|
|
|
||
5 |
(Orange) : Relay Out |
|
|
|
|
|
Lamp |
|
|
Relay Out |
|
Attaching the Core filter |
|
|
ENG |
• To reduce interference of electric wave. attach the core filter to BNC Cable (PAL Option) |
|||
• Attach the core filter closer to the jack of the product. |
|
|
|
Wind once!
BNC Cable ( PAL Option)
*Note: To attach the core filter to BNC Cable, roll the cable over core filter once.
*Note: Be careful not to damage the cable when attaching the core filter.
SCC-C6325/ SCC-C7325
Dual Voltage
DC 12V/AC 24V
IrDA
Sensor
Door
Switch
Controller/DVR |
Relay Out |
Sensors |
Relay Out |
|
|
|
|
|
|
BNC Video |
|
|
|
Lamp |
|
Cabling Terminal Block |
Relay Out |
|
|
English – 19
Installation
Power Connection
•Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back of main unit.
Power Mode |
Input Voltage Range |
Power Consumption |
||
C6323/ C6325 |
C7325 |
|||
|
|
|||
|
|
|
|
|
DC 12V |
DC 11V ~ 15V |
8 W |
12W |
|
|
|
|
|
|
AC24V |
AC 20V ~ 29V |
10W |
21W |
|
|
|
|
|
RS-485 Communication
•For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time, RS-485 communication lines of them is connected in parallel as shown below.
Keyboard Controller DVR
Video Connection |
If you want to use Alarm Input, the types of sensor |
• Connect with BNC coaxial cable. |
must be selected in OSD menu. The sensor types |
|
are Normal Open and Normal. If sensor type is |
|
not selected properly, the alarm can be activated |
Alarm Input Connection |
reversely. |
• Sensor Input |
|
|
|
|
|
|
Normal Open |
Sensor output is turned ON when |
|||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
IN1 |
(N.O) |
sensor is activated |
|||||
|
|
|
|||||||||
|
|
|
|
||||||||
INTERNALT ER N AL |
|
|
|
|
|
|
|
Normal Close |
Sensor output is turned OFF when |
||
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
(N.C) |
sensor is activated |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN 2 |
|
||||||
|
|
|
|
|
|
|
|
|
• Relay Output |
|
|
|
|
|
|
|
|
|
|
|
|
IN COM |
Internal |
|
Relay Out |
|
Power |
|
Relay Out |
It is noted that short circuit between GND and Input pin means alarm activation.
There are 4 Alarm Outputs and all of them are Relay contact type. Therefore, you do not have to care about polarity, AC/DC, and isolations between channels. Care must be taken for the power capacity of relay contact written above.
20 – 10X MINI SMART DOME CAMERA
Operation
CHECK POINTS BEFORE OPERATION
various functions using keyboard controller as well as simplify the interface with DVR and IP equipments.
•Before power is applied, please check the cables carefully.
•The camera ID of the controller must be identical to that of the camera to be controlled. The camera ID can be checked in the System Information of OSD Menu.
•If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
•If you changed camera protocol by changing DIP switch, the change will be effective after you reboot the camera.
•Since the operation method can be different for each controller available, refer to the manual for your controller if camera can not be controlled properly.
PRESET AND PATTERN
FUNCTION PRE-CHECK
•Check how to operate Preset, Scan, Auto Pan and Pattern function with controller or DVR in advance to operate camera function using them. (refer to your System keyboard Manual)
•If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more information, refer to “Reserved Preset” in this manual.
• Function |
|
<Go Preset> [95] |
: Enters into OSD menu |
<Go Preset> [131~134] |
: Runs Pattern Function 1 ~ 4 |
<Go Preset> [141~148] |
: Runs Auto Pan Function 1 ~ 8 |
<Go Preset> [151~158] |
: Runs Scan Function 1 ~ 8 |
<Go Preset> [161] |
: Sets Relay Output to OFF |
<Set Preset> [161] |
: Sets Relay Output to ON |
<Go Preset> [165] |
: Auto Calibration ON |
<Go Preset> [166] |
: Auto Calibration OFF |
<Go Preset> [167] |
: Zoom Proportional Jog ON |
<Set Preset>[167] |
: Zoom Proportional Jog OFF |
<Go Preset> [170] |
: Sets Camera BLC Mode to OFF |
<Go Preset> [171] |
: Sets Camera BLC Mode to HIGH |
<Go Preset> [174] |
: Sets Camera Focus Mode to |
|
AUTO |
<Go Preset> [175] |
: Sets Camera Focus Mode to |
ENG |
|
Manual |
|
<Go Preset> [176] |
: Sets Camera Focus Mode to |
|
|
SEMI-AUTO |
|
AUTO CALIBRATION
•If the camera is continuously subjected to very high temperature (over 50°C or 122°F) environment for a long time, it is possible for the camera to lose focus. As a result, you will get blurry image. In this case, it is recommended to turn on “AUTO CALIBRATION” by running Preset 165.
•If you execute AUTO CALIBRATION, camera will calibrate its focus at every 6 hours. To turn off this function, please, Run Preset 166.
<Go Preset> [177] |
: Sets Day & Night Mode to |
|
AUTO1 |
<Go Preset> [178] |
: Sets Day & Night Mode to |
|
NIGHT |
<Go Preset> [179] |
: Sets Day & Night Mode to DAY |
<Go Preset> [190] |
: Sets OSD Display Mode to |
|
AUTO (Except Privacy Mask) |
<Go Preset> [191] |
: Sets OSD Display Mode to OFF |
|
(Except Privacy Mask) |
<Go Preset> [192] |
: Setting OSD Display Mode to |
|
ON (Except Privacy Mask) |
STARTING OSD MENU
•Function
Using the OSD menu, Preset, Pattern, Auto Pan, Scan and Alarm Input function can be confi gured for each application.
•Enter Menu <Go Preset> [95]
RESERVED PRESET
•Description
Some Preset numbers are reserved for direct access to specifi c functions in OSD menu. These direct commands via preset provide quick execution of
<Go Preset> [193] |
: Sets all Privacy Mask Display to |
|
OFF |
<Go Preset> [194] |
: Sets all Privacy Mask Display to |
|
ON |
<Go Preset> [195] |
: Heater ON (Turn off after 5mins |
|
and switch to Auto mode) |
<Go Preset> [196] |
: Heater OFF (Turn off and switch |
|
to Manual mode) |
<Go Preset> [197] |
: Fan ON (Turn off after 5mins |
|
and switch to Auto mode) |
<Go Preset> [198] |
: Fan OFF (Turn off and switch to |
|
Manual mode) |
<Go Preset>[200] |
: Digital Zoom ON |
<Go Preset>[201] |
: Digital Zoom OFF |
English – 21
Operation
PRESET
•Function
Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128. It is noted that preset “95” is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset and they are adjusted by using OSD menu. Four relay outputs can be controlled in conjunction with one Preset.
•Set Preset
<Set Preset> [1~128]
•Run Preset
<Go Preset> [1~128]
•Delete Preset
To delete Preset, use OSD menu.
AUTO PAN
•Function
By using Auto Pan function, you can make camera to move between 2 Preset positions repeatedly. When Auto Pan function runs, camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera moves from the preset
assigned as the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise) direction.
|
Direction |
|
|
|
|
2nd Preset |
|
|
|
|
|
CW |
|
|
|
|
CCW |
Direction |
|
|
|
|
1st Preset
In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point, camera turns on its axis by 360˚ in CW(Clockwise) direction and then it turns on its axis by 360˚ in CCW(Counterclockwise) direction.
Speed can be set up from 1˚/sec to 180˚/sec.
•Set Auto Pan
To set Auto Pan, use OSD menu.
•Run Auto Pan
Method1) <Run Auto Pan> [Auto Pan NO.] [Enter]
Method2) <Go Preset> [Auto Pan NO.+140] ex) Run Auto Pan 2 : <Go Preset> [142]]
•Delete Auto Pan
To delete Auto Pan, use OSD menu.
PATTERN
•Function
Pattern Function enables to memorize the path (mostly curve path) created by keyboard controller. By running the pattern, the memorized path can be reconstructed exactly as it memorized whenever required.
4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern.
•Set Pattern
Pattern can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.]
–Pattern editing screen is displayed as bellow.
EDIT PATTERN 1
[NEAR:SAVE / FAR:DELETE] 0/0/X1/N
–Movement by Joystick and preset movement can be memorized in a pattern.
–The rest memory size is displayed in progress bar.
–To save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu:
See the section “How to use OSD Menu”.
22 – 10X MINI SMART DOME CAMERA
Operation
•Run Pattern
Method 1) <Run Pattern> [Pattern NO.] ex) Run Pattern 2 : <Run Pattern> [2] Method 2) <Go Preset> [Pattern NO.+130] ex) Run Pattern 2: <Go Preset> [132]
Tuesday at 9:00AM. If you choose Weekday, camera will move to Main gate everyday except weekend.
It is noted that due to the real time clock, the time data will be kept regardless of blackout. The initial time and day setup is essential to proper Schedule function.
•Delete Pattern
Use OSD menu to delete a Pattern.
When the pattern is saved or executed, the PAN/TILT is operated with Auto Flip OFF mode.
•Set Schedule
Use OSD Menu to create a Schedule
•Run Schedule
Use OSD Menu of Schedule Master Enable
SCAN
•Function
The Scan function allows running sequence of Presets, Patterns and/or Auto Pans. Max 8 Scan can be stored. Each Scan can have max 20 action entities which
can be preset, pattern or Auto Pan. Dwell time means the time interval between actions and is adjustable in the menu. Besides, there is an option number with which Preset speed as well as the repetition number of Pattern and Auto Pan can be set up.
Dwell Time
Preset 1 |
Pattern 5 |
Auto Pan 5 |
Max 20 entities
•Set Scan
Use OSD Menu to create a Scan .
•Run Scan
Method1) <Run Scan> [Scan No.] ex) Run Scan 2 : <Run Scan> [2]
Method2) <Run Preset> [Scan No.+150] ex) Run Scan 2 : <Run Preset> [152]
•Delete Scan
Use OSD Menu to delete.
SCHEDULE
•Function
The Schedule function allows running an appropriate function like Preset, Auto Pan, Pattern, Scan, Home move at designated day and time. For example, if you setup a rule Tuesday at 9:00AM and Preset 1 (say Main Gate), the camera will move to main gate every
•Delete Schedule
Use OSD Menu to delete.
OTHER FUNCTIONS
• Preset Lock |
|
|
This function is made to protect preset data from |
|
|
unauthorized overwriting. If Preset Lock is ON, |
|
|
Preset save command using Hot Key is disabled |
ENG |
|
while Preset save using OSD Menu is acceptable. |
||
• Power Up Action |
||
|
||
This function enables to resume the last action |
|
|
executed before power down. Most of actions such |
|
|
as Preset, Pattern, Auto Pan and Scan are available |
|
|
for this function but Jog actions are not available to |
|
|
resume. |
|
|
• Auto Flip |
|
|
In case that tilt angle arrives at the top of tilt orbit |
|
|
(90°), zoom module camera keep moving to opposite |
|
|
tilt direction (180°) to keep tracing targets. As soon |
|
|
as zoom module camera passes through the top |
|
|
of tilt direction (90°), images should be reversed |
|
|
automatically and F appears in screen. If this |
|
|
function is set to OFF, tilt movement range is 0 ~ 90°. |
|
|
• Parking Action |
|
|
This function enables to locate the camera to specifi c |
|
|
position automatically if operator doesn’t operate the |
|
|
controller for a while. The Park Time can be defi ned |
|
|
as an interval from 1 minute to 4 hours. |
|
|
• Alarm Input |
|
|
2 Alarm Inputs are used. If an external sensor |
|
|
is activated, camera can be set to move to |
|
|
corresponding preset position. It is noted that the |
|
|
latest alarm input is effective if multiple sensors are |
|
|
activated. |
|
English – 23
Operation
•Privacy Zone Mask
To protect privacy, MAX. 4 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With Spherical Coordinates system, powerful Privacy Zone Mask function is possible.
•GENERAL/SPECIAL Image Setup
WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2 modes, “General” mode & “Special” mode. The General mode means that WB or AE can be set up totally and simultaneously for all presets in
“ZOOM CAMERA SETUP” menu. The Special mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Special WB/AE value should activate correspondingly when camera arrives at each preset location.
During jog operation, General WB/AE value should be applied. All Special WB/AE value will not be changed regardless of General WB/AE value change.
•Semi Auto Focus
This mode enables to switch focus mode automatically operation by operation. Manual focus mode is selected during preset operation and Auto focus mode is recovered if jog operation is started. During Preset action, instead of auto focusing, manual focus data stored when it is created will be applied as soon as camera arrives to the preset. This is helpful to get well-focused image in a short time.
OSD DISPLAY OF MAIN SCREEN
|
LABEL12345 |
PRESET1 |
Action Title |
Preset Lable 1 |
|||
Date/Time |
|
|
Temperature |
|
|
Alarm |
|
Camera ID |
|
|
|
|
|
Information |
P/T/Z Information
Image Flip
Camera ID
•P/T/Z INFORMATION
Current Pan/Tilt angle in degree, zoom magnifi cation and a compass direction.
•Camera ID
Current Camera ID(Address).
•Action Title
Followings are possible Action Titles and their meaning.
“SET PRESET ×××” |
When Preset ××× is stored |
“PRESET ×××” |
When camera reach to |
|
Preset ××× |
“PATTERN ×” |
When Pattern × is in action |
“AUPx/PRESET XXX” |
When Auto Pan x is in action |
“UNDEFINED” |
When undefi ned function is |
|
called to run |
•Preset Label
The Label stored for specifi c Preset.
•Alarm Information
This information shows current state of Alarm Input. The “I” means Input and “O” is output. If an Input is ON state it will show the number of input. If an Input is OFF state, ‘-’ will be displayed. In the same way “O:1” means output 1 is ON “O:-“ is OFF.
Ex) When Point 2 of inputs are ON, and Output 1 is On, OSD will show as below
I:-2 0:1
•Image Flip
Shows that images are currently reversed by Auto Flip Function.
•Temperature
Current Temperature: Boxed “C” and “F” means Celsius and Fahrenheit respectively
•Date/Time
Displays Current Date and Time.
24 – 10X MINI SMART DOME CAMERA
How to use OSD Menu
GENERAL RULES OF KEY OPERATION FOR MENU
• The menu item surrounded with < > always means it has its sub menu.
•For all menu level, to go into sub menu, press NEAR or
ENTER key.
•To go to up-one-level menu, press FAR key.
•To move from items to item in the menu, use joystick in the Up/Down or Left/Right.
•To change a value of an item, use Up/Down of the joystick in the controller.
•PressNEAR or ENTER key to save values and Press FAR key to cancel values.
MAIN MENU
ROOT MENU
<SYSTEM INFORMATION> <DISPLAY SETUP> <MOTION SETUP> <FUNCTION SETUP> <CAMERA SETUP> <SYSTEM SETUP> <SYSTEM INITIALIZE>
EXIT
•SYSTEM INFORMATION
Shows System information such as current fi rmware version and communication settings.
•DISPLAY SETUP
Enable/Disable of OSD display on Main Screen.
•MOTION SETUP
Setup for motion related settings
•FUNCTION SETUP
Setup for various functions such as Preset, Auto Pan, Pattern, Scan and Schedule.
•CAMERA SETUP
Confi gure Camera related functions and data
•SYSTEM SETUP
Confi gure for Basic system setup.
•SYSTEM INITIALIZE
Initializes system confi guration and sets all data to factory default confi guration.
SYSTEM INFORMATION
SYSTEM INFORMATION
FIRMWARE VER |
1.0250 |
COLOR SYSTEM |
NTSC |
PROTOCOL |
SAMSUNG |
BAUD RATE |
9600 |
ADDRESS |
255 |
BACK
EXIT
•FIRMWARE VER.
Shows current fi rmware version of camera.
•COLOR SYSTEM
Shows current analog video system of the camera.
• PROTOCOL |
Shows current Protocol for PTZ |
|
control |
• BAUD RATE |
Shows current Baud rate of PTZ |
|
|
control. |
ENG |
• ADDRESS |
Shows current Camera ID for PTZ |
|
|
control. |
|
DISPLAY SETUP
DISPLAY SETUP |
|
CAMERA ID |
ON |
PTZ INFORMATION |
AUTO |
ACTION TITLE |
AUTO |
RESET LABEL |
AUTO |
ALARM I/O |
AUTO |
DATE/TIME |
ON |
<PRIVACY ZONE> |
|
TEMPERATURE |
CELSIUS |
BACK |
|
EXIT |
|
This menu defi nes Enable/Disable of OSD display on Main Screen. If an item is set to be AUTO, the item is displayed only when the value of it is changed.
• CAMERA ID |
[ON/OFF] |
• PTZ INFORMATION |
[ON/OFF/AUTO] |
• ACTION TITLE |
[ON/OFF/AUTO] |
• PRESET LABEL |
[ON/OFF/AUTO] |
• ALARM I/O |
[ON/OFF/AUTO] |
• DATE/TIME |
[ON/OFF] |
• TEMPERATURE |
[CELSIUS/FAHRENHEIT/OFF] |
English – 25
How to use OSD Menu
PRIVACY ZONE MASK SETUP
PRIVACY ZONE |
|
MASK NO. |
1 |
|
UNDEFINED |
DISPLAY |
OFF |
CLEAR MASK |
CANCEL |
<EDIT MASK> |
|
BACK
EXIT
Select area in image to mask. |
|
• MASK NO. |
[1~4] |
Select Mask number. If the selected mask has already data, camera moves as it was set. Otherwise, “UNDEFINED” will be displayed under “Mask NO”.
• DISPLAY |
[ON/OFF] |
Sets if camera makes mask shows or not on images.
• CLEAR MASK |
[CANCEL/OK] |
Deletes data in the selected MASK NO.
Privacy Zone Size Adjustment
EDIT MASK 1
[ |
|
|
WIDTH] |
:ADJUST MASK |
|||
[ |
:ADJUST MASK HEIGHT] |
[NEAR:SELECT/ FAR:CANCEL]
Adjust mask size. Use joystick or arrow buttons to adjust mask size.
• |
(Left/Right) |
Adjusts mask width. |
• |
(Up/Down) |
Adjusts mask height. |
It is noted that during PAN/TILT control like jog action, the object behind the privacy mask can be disclosed in a short period of time.
To hide a certain zone completely regardless of high speed PT motions, it is recommended that the size of mask must be 20% bigger than original target size
Privacy Zone Area Setup
EDIT MASK 1
MOVE TO TARGET POSITION [NEAR:SELECT/FAR:CANCEL]
0/0/x1/N
Move camera to area to mask. Then the menu to adjust mask size will be displayed.
MOTION SETUP
MOTION SETUP |
|
PRESET LOCK |
ON |
PWR UP ACTION |
ON |
AUTO FLIP |
ON |
JOG MAX SPEED |
140/SEC |
JOG DIRECTION |
NORMAL |
FRZ IN PRESET |
OFF |
<PARKING ACTION SETUP> <ALARM INPUT SETUP>
BACK
EXIT
Setup the general functions of Pan/Tilt motions.
• PRESET LOCK |
[ON/OFF] |
This function is made to protect preset data from unauthorized overwriting. If Preset Lock is ON, it is impossible to create and delete Preset, Auto Pan, Pattern and Scan. It is only possible to run those functions. To create and delete those functions, use OSD menu.
• POWER UP ACTION |
[ON/OFF] |
Refer to “Other Functions” section.
26 – 10X MINI SMART DOME CAMERA
How to use OSD Menu
• AUTO FLIP |
[ON/OFF] |
Refer to “Other Functions” section. |
|
• JOG MAX SPEED |
[2°/sec ~360°/sec] |
Sets maximum jog speed. Jog speed is inversely proportional to zoom magnifi cation. As zoom magnifi cation goes up, pan/tilt speed goes down.
Alarm Input Setup
ALARM INPUT SETUP
ALARM1 |
N.O |
PRESET1 |
ALARM2 |
N.C |
NOT USED |
• JOG DIRECTION |
[INVERSE/NORMAL] |
If you set this to ‘Normal’, the view in the screen is moving same direction with jog tilting. If ‘Inverse’ is selected, the view in the screen is moving reversely.
• FREEZE IN PRESET |
[ON/OFF] |
At start point of preset movement, camera starts freezing the image of start point. Camera keeps displaying the image of start point during preset movement and does not display the images which camera gets during preset movement. As soon as camera stops at preset end point, camera starts displaying live images which it gets at preset end point.
This function availability should be different by models.
Parking Action Setup
PARKING ACTION SETUP
PARK ENABLE |
OFF |
WATT TIME |
00:10:00 |
PARK ACTION |
HOME |
BACK
EXIT
Match the Alarm sensor input to one of Preset positions. If an external sensor is activated, camera will move to corresponding preset position when this item is predefi ned.
• ALARM TYPE |
|
[Normal OPEN(N.O) / Normal CLOSE](N.C)] |
|
Sets sensor input type. |
ENG |
• ALARM ACTION |
|
[NOT USED/HOME/PRESET 1~128/SCAN 1~8, |
|
PATTERN1~4, SCAN 1~4] |
|
For each Alarm input, you can assign |
|
counteraction functions (Preset, Auto Pan, Pattern |
|
and Scan). |
|
BACK
EXIT
If Park Enable is set to ON, camera runs assigned function automatically if there is no PTZ command during assigned “Wait Time”.
• |
PARK ENABLE |
[ON/OFF] |
• |
WAIT TIME |
[5 seconds ~ 4 hour] |
The time is displayed with “hh:mm:ss” format and you can change this by 1 min unit.
• PARK ACTION |
[HOME/PRESET/PATTERN/ |
|
AUTO PAN/SCAN] |
Ex) If HOME is selected for Park Action, camera will move to home position when there is no PTZ command during assigned “Wait Time.”
FUNCTION SETUP
FUNCTION SETUP
<PRESET SETUP> <AUTO PAN SETUP> <PATTERN SETUP> <SCAN SETUP> <SCHEDULE SETUP>
BACK
EXIT
Confi gure 5 Special Functions with this menu
•PRESET SETUP
127 Presets from the number 1 to 128 can be assigned excluding preset 95 reserved for Menu.
English – 27
How to use OSD Menu
•AUTO PAN SETUP
Up to 8 Auto Pans are available, which makes camera to move slowly between two preset points.
•PATTERN SETUP
Up to 4 patterns can be stored in the dome.
In this function, path data created by manual move of Joystick are recorded and you can playback the identical path automatically whenever required.
•SCAN SETUP
Up to 8 Scans can be defi ned.
In a Scan, max 20 entities are assigned from any combinations of Preset/Auto Pan/Pattern. If you run a Scan, camera will execute each entry sequentially.
•SCHEDULE SETUP
7 rules of Schedule can be assigned by day and time. Appropriate actions (such as Home, Preset, Auto Pan, Pattern and Scan) can be defi ned for each rule. Also, it is possible to use Weekday and Weekend in a rule to make it simple.
PRESET SETUP
PRESET SETUP |
|
PRESET NO. |
1 |
<EDIT SCENE> |
|
<LABEL> |
NORTH GATE |
CLR PRESET |
CANCEL |
CAM ADJUST |
GENERAL |
ALARM OUT |
- |
BACK |
|
EXIT |
|
• PRESET Number |
[1~128] |
If a selected preset is already defi ned, camera moves to pre-defi ned position and preset characteristics such as Label and Relay Outputs show on monitor. If a selected preset is not defi ned, “UNDEFINED” shows on monitor.
•EDIT PRESET SCENE
Redefi ne current Preset scene position (i.e. PTZ).
•EDIT PRESET LABEL
Edits Label to show on monitor when preset runs. MAX. 10 alphabets are allowed.
• CLEAR PRESET |
[CANCEL/OK] |
Delete current Preset data
• CAM ADJUST [GENERAL/SPECIAL]
WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2 modes, “General” mode & “Special” mode. The General mode means that WB or AE can be set up globally for all presets in “CAMERA SETUP” menu.
The Special mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Special WB/AE value will be applied when camera arrives to the preset location. During jog operation, General WB/AE value should be applied.
All Special WB/AE value will not be affected by General WB/AE value changes. If “Special’’ is selected, Menu to set WB/AE shows on monitor. Its default is GENERAL.
•ALARM OUT
Relay Output can be linked with Preset run.
The character“-“means disable while the number “1” representing each bit means ON.
Ex) If it is set to “1”, Output relay will be ON whenever you call this Preset.
Edit Preset Scene
EDIT SCENE - PRESET 1
MOVE TO TARGET POSITION [NEAR:SELECT/ FAR:CANCEL]
0/0/x1/N
Using Joystick, move camera to desired position.
By pressing NEAR or ENTER key, save current PTZ data.
Press FAR key to cancel.
28 – 10X MINI SMART DOME CAMERA
How to use OSD Menu
Edit Preset Label
AUTO PAN SETUP
LABEL - PRESET 1
[█ ]
----------
1234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx
yz<>-/:.
----------
Edits label to show on monitor when camera arrives at presets. In Edit Label menu, a reverse rectangular is cursor. As soon as fi nishing selecting alphabet, cursor moves to the next digit.
AUTO PAN SETUP |
|
APAN NO. |
1 |
1ST POS. |
NOT USED |
2ND POS. |
NOT USED |
APAN SPEED |
30/SEC |
CLEAR APAN |
CANCEL |
BACK |
|
EXIT |
|
• APAN Number |
[1~8] |
Selects Auto Pan number to edit. If a selected Auto Pan has not defi ned, “NOT USED” is displayed in 1st Position and 2nd Position
[█ |
] |
• 1ST POSITION |
[PRESET 1~128] |
|
|
• 2ND POSITION |
|
Current Cursor Position
Using Left/Right/Up/Down of joystick, move to an appropriate character from the Character set. To choose that character, press the NEAR or
ENTER key.
Set up the 2 position for Auto Pan function. If a |
ENG |
|
selected preset is not defi ned, “UNDEFINED” will be |
||
|
||
displayed as shown below. |
|
|
AUTO PAN SETUP |
|
----------
1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:.
----------
Space Char. Back Space Char.
If you want to use blank, choose Space character (“ ”). If you want to delete a character before, use back space character (“ ”).
If you complete the Label editing, move cursor to “OK” and press NEAR or ENTER key to save completed label. To abort current change, move cursor to “Cancel” and press NEAR or ENTER key.
APAN NO. |
1 |
|
1ST |
POS. |
PRESET5 |
2ND |
POS. |
NOT USED |
|
|
UNDEFINED |
|
|
When Auto Pan function runs, camera moves from the preset assigned as the 1st point to the
preset assigned as the 2nd point in CW (Clockwise) direction. Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW (Counterclockwise) direction. In case that the preset assigned as the 1st point
is same as the preset assigned as the 2nd point, camera turns on its axis by 360° in CW direction and then it turns on its axis by 360° in CCW direction.
• APAN SPEED |
[1°/sec ~180°/sec] |
Sets Auto Pan speed from 1°/sec to 180°/sec.
• CLEAR APAN |
[CANCEL/OK] |
Deletes current Auto Pan data.
English – 29
How to use OSD Menu
PATTERN SETUP
PATTERN SETUP
PATTERN NO. 1 UNDEFINED
CLR PATTERN CANCEL <EDIT PATTERN>
BACK
EXIT
• PATTERN Number [1~4 ]
Selects Pattern number to edit.
If a selected pattern number is not defi ned, “UNDEFINED” will be displayed under selected pattern number.
• CLEAR PATTERN |
[CANCEL/OK] |
Deletes data in current pattern |
|
• EDIT PATTERN |
Starts editing pattern. |
Edit Pattern
By using Joystick, move to start position with appropriate zoom. To start pattern recording, press NEAR or ENTER key. To exit this menu, press FAR key.
EDIT PATTERN 1
MOVE TO START POSITION [NEAR:START/ FAR:CANCEL]
0/0/x1/N
Move camera with joystick of controller or run preset function to memorize the path (mostly curve path) in a selected pattern. The total memory size and the rest memory size is displayed in the form of bar. Maximum 1200 communication commands can be stored in a pattern.
30 – 10X MINI SMART DOME CAMERA
EDIT PATTERN 1
[NEAR:SAVE / FAR:DELETE] 0/0/X1/N
To save data and exit, press NEAR or ENTER key. To cancel recording and delete record data, press FAR key.
SCAN SETUP
SCAN SETUP |
|
SCAN NO. |
1 |
|
UNDEFINED |
CLEAR SCAN |
CANCEL |
<EDIT SCAN> |
|
BACK
EXIT
• SCAN Number [1~8]
Selects Scan number to edit.
If a selected Scan number is not defi ned, “UNDEFINED” will be displayed under selected Scan number.
• CLEAR SCAN |
[CANCEL/OK] |
Deletes data in current Scan |
|
• EDIT SCAN |
Starts editing Scan. |
Edit Scan
Press NEAR or ENTER key in “NO” list to start Scan setup.
EDIT SCAN |
1 |
NO. ACTION NO. DWELL OPT
1 NONE
2NONE
3NONE
4NONE
5NONE
SAVE
CANCEL [NEAR:EDIT]