Samsung SCC-C6325, SCC-C6323, SCC-C7325 User Manual

10x Mini Smart

Dome Camera

SCC-C6323 SCC-C6325 SCC-C7325

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsung.com/global/register

ENG FRE

GER SPA

ITA

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

WARNING

•

To prevent damage which may result in ﬁ re or electric shock hazard, do not expose this appliance to rain or moisture.

WARNING

Be sure to use only the standard adapter that is speciﬁ ed in the speciﬁ cation sheet. Using any other adapter could cause ﬁ re, electrical shock, or damage to the product

Incorrectly connecting the power supply or replacing battery may cause explosion, ﬁ re, electric shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or ﬁ re.

Securely plug the power cord into the power receptacle. Insecure connection may cause ﬁ re.

When installing the camera, fasten it securely and ﬁ rmly. A falling camera may cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers ﬁ lled with water on top of the camera. Doing so may cause personal injury due to ﬁ re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁ re or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause ﬁ re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modiﬁ cations or attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁ re or electric shock.

10.

If the camera is installed or rebooted after power failure when ambient temperature is below the freezing point,

11.

the dome cover is frosted. In this case, the frost will be disappeared after 3 hours after turning on the power. (It is noted that lowest guaranteed operating temperature is -45º C (-49º F) without wind.)

2 – 10X MINI SMART DOME CAMERA

Safety information

CAUTION

Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to

excessive vibrationor magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high

humidity. Doing so may cause ﬁ re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall

it.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause ﬁ re or

damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁ re.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the

CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as vases,

shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

ENG

English – 3

Important Safety Instructions

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliﬁ ers) that

produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience

10.

receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁ ed by the manufacturer.

11.

Use only with cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold

12.

with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus

13.

combination to avoid injury from tip-over.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in

14.

any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4 – 10X MINI SMART DOME CAMERA

Contents

Introduction

Features 7

Product & Accessories 8

Parts Name & Functions 10

Installation

DIP Switch Setup 13

Installation using Surface mount on the Ceiling 14

Installation using Ceiling Mount Bracket (SCC-C7325) 16

Installation using Wall Mount Bracket (SCC-C7325) 17

Cabling 19

Operation

Check points before operation 21

Preset and Pattern Function Pre-Check 21

Starting OSD Menu 21

Reserved Preset 21

Preset 22

Auto Pan 22

Pattern 22

Scan 23

Schedule 23

Other Functions 23

OSD Display of Main Screen 24

General Rules of Key Operation for Menu 25

Main Menu 25

System Information 25

Display Setup 25

English – 5

ENG

Contents

How to use OSD Menu

Privacy Zone Mask Setup 26

Motion Setup 26

Function Setup 27

PRESET Setup 28

Auto Pan Setup 29

Pattern Setup 30

Scan Setup 30

Schedule Setup 32

Camera Setup 33

System Setup 34

System Initialize 36

Speciﬁ cations

Speciﬁ cations 38

Dimension 41

❖

6 – 10X MINI SMART DOME CAMERA

FEATURES

Camera Speciﬁ cations

❖

CCD Sensor : 1/4” Interline Transfer CCD

•

Zoom Magniﬁ cation : x10 Optical Zoom, x10

• Digital Zoom (Max x 100 Zoom)

Day & Night Function

•

Various Focus Mode: Auto-Focus / Manual Focus

• / Semi-Auto Focus.

Independent or General Camera Characteristic

• Setup in Preset operation

Powerful Pan/Tilt Functions

❖

•

Max. 360°/sec high speed Pan/Tilt Motion

•

Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result, time to target view is reduced dramatically and the video on the monitor is very natural to watch.

•

For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy to locate camera to desired target view.

•

Owing to zoom-proportional pan/tilt speed, camera can be moved to a desired position in accurate manner even though zoom ratio is high.

Preset, Pattern, Auto Pan, Scan, Privacy

❖

Mask, Schedule and More…

MAX. 127 Presets are assignable and

• characteristics of each preset can be set up independently, such as White Balance, Auto Exposure, Label and so on.

Max. 8 Auto Pan can be stored. This enables to

• move camera repetitively between two preset positions with designated speed.

Max. 4 of Patterns can be recorded and

• executed. This enables for camera to track a surveillance trajectory as closely as possible which are recorded from operator’s motion of joystick.

Max. 8 Scan can be stored. To compose a

• surveillance trajectory, the Group can have max. 20 entities of Preset/Pattern/Scan functions. This enables for camera to move a combinations of those functions repetitively.

Max. 4 Masks are settable independently to

• protect privacy zone. The mask is arbitrary-sized rectangular and locate any location in view space.

Introduction

•

7 rules of Schedule can be assigned by day and time. Appropriate actions (such as Home, Preset, Auto Pan, Pattern, Scan) can be deﬁ ned for each rule. Also, it is possible to make rule by Weekday and Allday to simplify the rule.

PTZ(Pan/Tilt/Zoom) Control

❖

With RS-485 communication, max. 255 of

• cameras can be controlled at the same time.

Pelco-D/ Pelco-P, Samsung protocol can be

• selected as a control protocol in the current version of ﬁ rmware.

OSD(On Screen Display) Menu

❖

•

OSD menu is provided to display the status of camera and to conﬁ gure the functions interactively.

•

Currently, 7 Languages are supported for OSD Menu: [ENGLISH/ESPAÑOL/FRANÇAIS/

DEUTSCH/ITALIANO/РУССКИЙ/PORTUGUÊS]

•

The information such as Camera ID, Pan/Tilt/ Zoom/Direction, Alarm Input & Output, date/time, current temperature and Preset can be displayed on screen.

•

Each display item can be turned On or Off independently.

Alarm I/O Functions

❖

2 alarm sensor Inputs and 1 relay output are

• available.

To reject external electric noise and shock

• perfectly, alarm sensor Input is decoupled with photo coupler.

If an external sensor is activated, camera can be

• set to move to the corresponding Preset position.

Relay output can be assigned to work with a

• certain preset.

❖

Reserved Presets for Special Purpose

Besides regular 127 presets, direct calling of

• reserved presets enables to set up many of camera functions with without using OSD menu. For more information, refer to “Reserved Preset” in this manual.

ENG

English – 7

Introduction

PRODUCT & ACCESSORIES

Product & Accessories (SCC-C6323)

❖

Main Product

•

Main Body Surface Mount Bracket

Accessory

•

❖

Manual

Product & Accessories (SCC-C6325)

❖

Main Product

•



Main Body Surface Mount Bracket

Accessory

•

Screw & Plastic Anchor (4Pcs)

Mount Bracket Option : Please use SADT-937WM for this purpose.Ú

8 – 10X MINI SMART DOME CAMERA

Terminal Block Torx Screw Driver Surface Mount

Screw & Plastic Anchor (4Pcs)



Gasket

Manual

Product & Accessories (SCC-C7325)

❖

Main Product

•



Main Body Sun Shield Housing

Accessory

•

Introduction

ENG

Terminal Block

Mount Bracket Option

•

Torx Screw Driver Manual

Ceiling Mount Bracket (SADT-732CM)Wall Mount Bracket (SADT-732WM)

English – 9

Introduction

PARTS NAME & FUNCTIONS

SCC-C6323❖

❖

Surface Mount Bracket

Separating Slit

Dome Cover

Main Unit / Surface Mount Bracket Back of Main Unit

Surface Mount Bracket

•

This is used to install the camera directly on the ceiling. After separating this cover ﬁ rst and then attach this directly to ceiling. Camera must be assembled at the last stage. Do not use this bracket when installing camera on the wall with wall mount bracket or on the ceiling with ceiling mount bracket.

Separating Slit

• Using a coin, you can separate upper part lower

body of the dome.



Dome Cover

• Do not detach protection vinyl from dome cover

before ﬁ nishing all installation process to protect dome cover from scratches or dust.

DIP Switch

• Adjusts camera ID and protocols.

Cable Duct

• When you want to install the camera on the surface

of hard ceiling, you need to handle the cable through side of the dome. In this case, break the side wall bit and make the cable pass through the cable duct.

DIP Switch

Cable Duct

10 – 10X MINI SMART DOME CAMERA

SCC-C6325❖

Surface Mount Bracket

Mounting Hole

Introduction



Main Body

Lockup Screw

Dome Cover

Main Unit / Surface Mount Bracket Back of Main Unit

Dome Cover

•

Do not remove the protection vinyl from dome cover before ﬁ nishing all installation process to protect dome cover from scratches or dust.

Surface Mount Bracket

• This is used to install the camera directly on the

ceiling. After separating this cover, mount this bracket on to ceiling. Main body of the camera is going to be assembled again in the last stage.

Do not use this bracket with wall mount bracket or ceiling mount bracket.

Lockup Screw

• Fixes main unit brackets like surface, wall, and

ceiling.

Cabling Terminal Block

• During installation, Power, Video, Communication,

Alarm Input cables are connected on to this cabling terminal block.

DIP Switch

• Adjusts camera ID and protocols.

Cabling Terminal Block

DIP Switch

ENG

English – 11

Introduction

PARTS NAME & FUNCTIONS

SCC-C7325❖

Sun Shield Housing

Main Body

Lockup Screw

Dome Cover

Main Unit / Surface Mount Bracket Back of Main Unit

Dome Cover

•

Do not remove the protection vinyl from dome cover before ﬁ nishing all installation process to protect dome cover from scratches or dust.

Sun Shield Housing

•

Lockup Screw

• Fixes main unit brackets like surface, wall, and

ceiling.

Cabling Terminal Block

• During installation, Power, Video, Communication,

Alarm Input cables are connected on to this cabling terminal block.

DIP Switch

• Adjusts camera ID and protocols.

Cabling Terminal Block

DIP Switch

B s c

❖

12 – 10X MINI SMART DOME CAMERA

❖

DIP SWITCH SETUP

123456

Before you install the camera, you should set the DIP switches to conﬁ gure the camera ID, Baud rate, and communication protocol.

Protocol

Auto Select

Camera ID Setup

❖

ID number of camera is set using binary number.

• The example is shown bellow.

Pin 12345678

ID Value 1 2 4 8 16 32 64 128

ex) ID=5

ex) ID=10onoff

The range of ID is 0~255. Factory default of

• Camera ID is 1.

If you want to control a certain camera, you must

• match the camera ID with Cam ID setting of DVR or Controller.

Communication Protocol Setup

❖



offonon

Buad Rate

ID Setting (1~255)

offonoff

off

RS-485 Terminate

off

Installation

•

Select the appropriate Protocol with DIP switch combination.

Switch State

Pin1 Pin2 Pin3 Pin4

OFF OFF OFF OFF Auto Protocol

ON OFF OFF OFF Pelco-D

OFF ON OFF OFF Pelco-P

ON ON OFF OFF Samsung

If you set the protocol as Auto Protocol, camera

• will automatically recognize the kind of Protocol.

Auto Protocol supports Pelco-D and Samsung Protocol.

•

If you want to control using DVR or system

• keyboard, their protocol must be identical to camera. Otherwise, you can not control the camera.

If you changed camera protocol by changing DIP S/W,

• the change will be effective after you reboot the camera.

Factory default of protocol is “Auto Protocol

•

Communication Baud rate Setup

❖

Select the appropriate Baud rate with DIP switch

• combination.

Switch State

off

Pin5 Pin6 Pin7

OFF OFF OFF 2400 BPS

ON OFF OFF 4800 BPS

OFF ON OFF 9600 BPS

ON ON OFF 19200 BPS

OFF OFF ON 38400 BPS

•

Factory default of Baud rate is “9600 BPS”

Protocol

ENG

Protocol

123456

English – 13

+ 30 hidden pages