Samsung SCC-B5366SBP, SCC-B5368P, SCC-B5366P, SCC-B5366BP User Manual

SCC-B5366 SCC-B5368 SCC-B5366S SCC-B5368S
DIGITAL COLOR DOME
CAMERA
user manual
ENG RUS
ENG
POL
CZE
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service, please register your product at
www.samsungsecurity.com
TUR
Safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
To prevent damage which may result in fi re or electric shock hazard, do not expose this appliance to rain
or moisture.
WARNING
Be sure to use only the standard adapter that is specifi ed in the specifi cation sheet. Using any other adapter
1. could cause fi re, electrical shock, or damage to the product
Incorrectly connecting the power supply or replacing battery may cause explosion, fi re, electric shock, or
2. damage to the product.
Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
3. generation or fi re.
Securely plug the power cord into the power receptacle. Insecure connection may cause fi re.
4. When installing the camera, fasten it securely and fi rmly. A falling camera may cause personal injury.
5. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers fi lled with water
6. on top of the camera. Doing so may cause personal injury due to fi re, electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock.
7.
2 – DIGITAL COLOR DOME CAMERA
Safety information
8.
If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock.
9.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.)
10.
When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock.
CAUTION
1.
Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibrationor magnetic interference.
2.
Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fi re or electric shock.
3.
If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4.
Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fi re or damage to the product.
Keep out of direct sunlight and heat radiation sources. It may cause fi re.
5. Install it in a place with good ventilation.
6. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
7. CCD image sensor.
Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases,
8. shall be placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
9.
English 3
ENG
Important Safety Instructions
WARNING
Read these instructions.
1. Keep these instructions.
2. Heed all warnings.
3. Follow all instructions.
4. Do not use this apparatus near water.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
8. amplifi ers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
9. with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
10. the point where they exit from the apparatus.
Only use attachments/accessories specifi ed by the manufacturer.
11. Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or
12. sold with the apparatus.
Unplug this apparatus when a card is used. Use caution when moving the cart/
13. apparatus combination to avoid injury from tip-over.
Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been
14. damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
4 – DIGITAL COLOR DOME CAMERA
Contents
Introduction
Features 6 Product & Accessories 7 Part Names and Functions 8
Installation
Before installation 11 Installation procedure 11 Adjusting the camera direction 13
How to use OSD Menu
Using Icons in the Menu 14 Main Menu 14 Profi le 15 Camera Setup 17 Intelligence 24 Privacy Zone Setup Other Set 28 System Information 29 Language 29
Specifi cations
Specifi cations 30
27
English 5
ENG
Introduction
FEATURES
High Resolution
This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special algorithm technologies.
Intelligent Motion Detection & Tracking
This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it displays an alert if an object passes / enters /exits the virtual fence or virtual area.
XDR (eXtended Dynamic Range)
Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a
certain pixel unit to determine the optimal visibility.
High Sensitivity
It implements images of high sensitivity using the up-to-date SONY Super-HAD IT CCD..
Low Illumination
It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera
identify objects even in the worst environment.
Superior Backlight Adjustment
When an object has a bright illumination or sunlight behind it, this camera automatically improves the
shaded object picture quality.
Digital Power Synchronization
The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the
operationability and reliability of this camera.
Output Signal Setting
You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy,
Horizontal/Vertical profi ling, and digital zooming.
OSD(On Screen Display) Menu
OSD menu is provided to display the status of camera and to confi gure the functions interactively.
6 – DIGITAL COLOR DOME CAMERA
Introduction
Coaxial Cable Communication
This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the
control signal. In installation or repair, this helps you control the communication controller (optional) without additional cabling.
PRODUCT & ACCESSORIES
Product & Accessories
Main Product
Camera
Accessories
Test Monitor Cable
Note :
The test monitor cable is used to test the camera by connecting to a portable display. If you really want to connect the camera
to a monitoring display, use the BNC cable.
Tab screw
User’s Manual
ENG
English 7
Introduction
PART NAMES AND FUNCTIONS
Components of your camera
8 – DIGITAL COLOR DOME CAMERA
테스트 모니터 출력
Test monitor output
Lens
렌즈
Video connector
비디오 커넥터
Power connector
전원 커넥터
Introduction
No Name Brief description
1 Cover dome Covers the inner cover, lens, and main body to protect them.
2 Inner cover Covers the main body to protect it.
3 Wing locker
4 Main body Includes a lens, a switch board, a PCB board, screws, and such.
5 Mount bracket
6 Wiring Passage
7 Zoom lever Using this lever, the lens zoom can be adjusted and fi xed.
8 Focus lever The lens focus can be adjusted by rotating it left or right. Rotate it clockwise for fi xing.
9 Tilt fi xing screw Using this screw, the slope of the lens can be adjusted and fi xed.
10 4-way Switch This switch is used to set and adjust the settings of the camera’s functions.
11 Groove mark
12 Locker Used to open or close the Cover dome. To open the cover dome, press the locker.
13 Lock releaser
14 Cable Connect the Video connector to BNC cable and Power connector to power adapter.
Push a long thin screwdriver into its narrow spot and press it outward when you want to remove the inner cover.
Used as a ceiling or wall fi xture. It is fi xed using three long tab screws provided in the package.
This passage is designed to make arrangement of the cables if you drill a hole to extend the wiring.
ENG
To attach the Main body to the Mount bracket, align this groove mark on the Main body with the wide groove in the CAMERA FRONT side on the Mount bracket.
Push it outward and rotate the main body in UNLOCK direction when you want to remove the Mount bracket from the Main body or to remove the installed camera from the Mount bracket.
English 9
Introduction
Setting switches
SETUP Switch
This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the MAIN MENU appears.
ef
(Left/Right)
: By pressing this switch left or right, you can move left or right on the menu or change the
cd
(Up/Down) :
: When you press this switch in the menu, the selected function is confi rmed. To enter a submenu, press
this button..
10 – DIGITAL COLOR DOME CAMERA
displayed value. By pressing this switch up or down, you can move up or down on the menu.
Installation
BEFORE INSTALLATION
Before installing your camera, you have to read the following cautions.
You have to check whether the location (ceiling or wall) can bear fi ve times the weight of your camera.
Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it
may cause a breakdown or fi re. When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
INSTALLATION PROCEDURE

ENG
English 11
Installation
Press the Locker button on the bottom of your camera and remove the Cover dome from the Main body
using the other hand. The Main body and Inner cover will be exposed to you.
To install and adjust your camera, you have to fi rst remove the Inner cover. To remove the Inner cover from
the Main body, push a long thin screwdriver into the narrow spot of the Wing locker and press it outward to remove the cover.
Remove the Mount bracket from the Main body by rotating the Main body in the UNLOCK direction while
pushing the Lock releaser outward. If it is not easily done, rotate the Mount bracket in the LOCK direction while holding small holes on the Mount bracket.
Fix the Mount bracket to the location (ceiling or wall) with supplied three screws.
Note :
The CAMERA FRONT sign on the Mount bracket should face the camera monitoring area.
Extend the wiring up to the ceiling or wall through the bracket.
Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning the Groove
mark on the Main body with the wide groove around the CAMERA FRONT inlay.
Adjust the camera direction. For more details on the direction control, see “Adjusting the camera direction,”
on the same page. When required to adjust the zoom and focus for your camera, see “Connecting cables and changing the settings,” on page 10.
Attach the Inner cover to the Main body by pressing it until a “click” sound is heard after aligning two screw
holes on the Wing lockers of the Inner cover with two screw holes on the Main body’s left and right sides.
Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard after aligning the
bump inside the Cover dome with the Groove mark on the Main body.
12 – DIGITAL COLOR DOME CAMERA
Installation
ADJUSTING THE CAMERA DIRECTION
When the camera is fi xed on the ceiling, you can adjust the camera viewing angle. You can rotate your camera leftward or rightward (Panning), and can change the slope of your camera upward or downward (Tilting).
In case of panning, the rotation limit of your camera is set to 355 degree (100 degree clockwise and 255 degree counterclockwise). The rotation is stopped by the Stopper inside of the camera. For panning control, fi rst unfasten two screws located on the bottom and rotate in the direction you want, and then fasten them to fi x the camera.
In case of tilting, you can change the slope of your camera from zero to 90 degree. However if the slope angle is under 17 degree, you can encounter a partial image hide problem. To fi x the location after adjusting the tilting angle, use the Tilt fi xing screws.
To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever. When you install the camera on the inclined ceiling or wall, you can rotate the camera lens to see a correct direction image.
Tilting
Panning
Lens rotation
English 13
ENG
How to use OSD Menu
USING ICONS IN THE MENU
(EXIT)
Exits the menu setting. Before you exits the menu setting, select SAVE to save your settings, or select QUIT to cancel.
(RET)
Returns to the previous menu.
(HOME)
Returns to the main menu.
(SAVE)
Used to save your settings of MASK AREA, PRIVACY ZONE and more. Once you save your settings, they will remain even if you select QUIT in the menu.
(DEL)
Used to deletes your settings of MASK AREA, PRIVACY ZONE and more. Once you delete your settings, they will not be restored even if you select QUIT in the menu.
14 – DIGITAL COLOR DOME CAMERA
MAIN MENU
PROFILE
You can set a mode according to the camera installation conditions.
CAMERA SET
Confi gure Camera related functions and data.
INTELLIGENCE
You can confi gure the settings of motion detection, tracking and more.
PRIVACY ZONE
You can confi gure the privacy related settings.
OTHER SET
You can confi gure for Factory Defaults, and more.
SYSTEM INFO.
Displays the system information including the camera version and communication settings.
LANGUAGE
Select a preferred one from the supported languages.
ÃÃMAIN MENUÃÃ
PROFILE
CAMERA SET INTELLIGENCE PRIVACY ZONE
OTHER SET
SYSTEM INFO
LANGUAGE
PROFILE
How to use OSD Menu
e
PROFILE
f
STANDARD
Ã
ITS BACKLIGHT DAY/NIGHT
GAMING CUSTOM
In the PROFILE menu, you can confi gure the following camera settings at once.
CAMERA SET Menu
Previous
MOTION (F.FAST)--- (F.FAST)--- NORM (F.FAST)--- SLOW
SHUTTER OFF AUTO1/250 OFF OFF OFF SENS-UP AUTOx4 AUTOx2 AUTOx4 AUTOx4 AUTOx4
Sub-menus
Menu
IRIS ALC ALC ALC ALC ALC
ALC -- ---
BACKLIGHT OFF OFF BLC OFF OFF
DNR MID MID MID MID MID
XDR MID MID MID MID MID
DAY/
NIGHT
NIGHT-- ---
STANDARD ITS BACKLIGHT DAY/NIGHT GAMING
LENSDCDC DCDCDC
LEVEL 0 0 0 0 0
AUTO AUTO DAY AUTO DAY
BURST OFF ON OFF OFF OFF
English 15
ENG
How to use OSD Menu
CAMERA SET Menu
Previous
Sub-menus
Menu
WHITE
BAL
DAY -- ---
NIGHT-- ---
BRIGHTNESS
DETAIL 2 2 2 2 2
ITS
It will be set automatically so you can easily check the traffi c conditions.
BACKLIGHT
It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.
DAY/NIGHT
It will be set automatically so it optimizes to the day or night conditions, respectively.
GAMING
It will be set automatically to help you take a picture in a regular indoor lighting condition.
16 – DIGITAL COLOR DOME CAMERA
STANDARD ITS BACKLIGHT DAY/NIGHT GAMING
DAY DAY/NIGHT DAY DAY/NIGHT DAY
MODE ATW2 ATW1 ATW1 ATW1 ATW1
RED00 000
BLUE 0 0 0 0 0
User setting
allowed
MODE OFF ATW2 OFF ATW2 OFF
User setting
RED
allowed
User setting
BLUE
allowed
MID
User setting
allowed
User setting
0
0
allowed
User setting
allowed
MID
User setting
allowed
User setting
0
0
allowed
User setting
allowed
CAMERA SETUP
eCAMERA SETf
CAMERA ID OFF IRIS ALC MOTION (F.FAST)--­DNR MID SHUTTER OFF SENS-UP AUTO X4 FLICKERLESS OFF XDR MID
DAY/NIGHT AUTO WHITE BAL DIGITAL ZOOM DETAIL [2] V-SYNC (INT)--­AGC COLOR SUP REVERSE H/V POSI/NEGA + PIP OFF
DIS OFF
d
c
OFF
LOW
d
c
How to use OSD Menu
Setup the general functions of zoom camera module. Use the
cdef
CAMERA ID [OFF, ON]
The CAMERA ID menu is used for you to assign a unique name to a camera. If you press the SETUP switch with the CAMERA ID menu selected, you will see the appropriate screen.
You can enter up to 54 alphanumeric or special characters for the CAMERA ID. Select LOCATION and press the SETUP switch to move the display position of the CAMERA ID.
IRIS [ALC]
The IRIS menu is used if you want to adjust the intensity of radiation incoming to the camera.
ALC (Automatic Light Control)
If you press the SETUP switch with an ALC-
switch to select a menu item.
CAMERA ID
ABCDEFGHIJKLMNOPQRSTUVWXYZ0 123456789 :?-+*()/
SP
ffee
SP LOCATION
CAMERA-1..................
...........................
based sub menu selected, you will see the appropriate screen.
English 17
ENG
How to use OSD Menu
ALC
LEVEL [00]----I---­BACKLIGHT OFF
The LEVEL menu is used to adjust the overall brightness, where “+” will increase the brightness and “–” will decrease it.
If you set the BACKLIGHT option to BLC,
you will see a menu where you can set the BLC area.
you can set the desired BLC zone by defi ning the size and location.
ALC
LEVEL [00]----I---­BACKLIGHT BLC AREA USER <SIZE> <LOCATION>
displayed dark on the monitor affected by the backlight. To solve this problem, you can use the BLC(Back Light Compensation) function to improve the sharpness of the image in such a high contrast scene.
AGC [OFF, VERY LOW, LOW, MID, HIGH, VERY HIGH, USER, FIX]
The AGC (Auto Gain Control) menu is used to set the AGC level of the camera. When the AGC is active, the camera automatically increases the sensitivity by amplifying the Video signal when the strength of the signal falls below the normal value.
If OFF or FIX mode is selected in the SENS-UP menu, you can specify the AGC level.
If you press the SETUP switch with a USER sub menu selected, you will see the appropriate screen.
LEVEL [16]
AGC USER
If you use an ordinary camera in a scene with an intensive backlight, the object will be
18 – DIGITAL COLOR DOME CAMERA
In USER mode, you can break down the level in 16 steps from VERY LOW to VERY HIGH to your preference.
How to use OSD Menu
AGC FIX
LEVEL [01]
If you press the SETUP switch with a FIX sub menu selected, you will see the appropriate screen.
As a fi xed value of the AGC gain is used in FIX mode, you can select one of the 16 detailed levels from VERY LOW to VERY HIGH before fi xing it.
Note :
If the DAY/NIGHT menu of the CAMERA SET is set to
AUTO, the AGC menu will be deactivated. If FLICKERLESS is set to ON, the AGC FIX mode will be
disabled.
MOTION
The MOTION menu is used to adjust the strength of the AGC level for a control of the camera motion. This is available only if the SENS-UP menu is set to AUTO. You can select one from S.SLOW, SLOW, NORM, FAST and F.FAST for the AGC level.
If you monitor a fast moving object in a low contrast scene, select F.FAST while select S.SLOW for a hardly moving object in the same lighting condition.
[S.SLOW, SLOW, NORM, FAST, F.FAST]
Note :
If the DAY/NIGHT menu of the CAMERA SET is set to
AUTO, the MOTION menu will be deactivated.
DNR
You can confi gure the DNR (Digital Noise Reduction) related settings.
Reduces the noise on the screen. This is especially useful for a severely distorted screen.
You can set the level if you set DNR to USER.
SHUTTER
[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250, AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO 1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10K]
The SHUTTER menu is used to confi gure settings of the fi xed / auto high-speed electronic shutter.
You can select one of 7 options from 1/100(PAL:1/120) to 1/10K for the fi xed high speed electronic shutter, which is mostly used for imaging a fast moving object.
The auto high speed electronic shutter operates as the fi xed high speed shutter in a high contrast scene but automatically focuses the target if the iris opens fully in a low contrast scene like in ELC mode. When it gets brighter back, the mode will switch to the fi xed high speed electronic shutter mode.
However, the auto high speed shutter operates properly only in a camera featuring a DC or VIDEO lens.
[OFF,LOW,MID,HIGH, USER(1~16)]
English 19
ENG
How to use OSD Menu
FLICKERLESS [OFF, ON]
Note :
If the SENS-UP function is set to AUTO, only items of
OFF and AUTO are available in the SHUTTER menu. If the SENS-UP mode is set to FIX, the SHUTTER menu
will be deactivated.
If the FLICKERLESS function is set to ON, the SHUTTER menu will be deactivated.
SENS-UP
[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO X8, AUTO X12, AUTO X16, AUTO X24, AUTO X32, AUTO X48, AUTO X64, AUTO X96, AUTO X128, AUTO X256, AUTO X512, FIX X2, FIX X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24, FIX X32, FIX X48, FIX X64, FIX X96, FIX X128, FIX X256, FIX X512]
Automatically detects the ambient level of darkness in the dark or low contrast scene to extend the accumulated time, keeping the image bright and sharp; It can be also used as FIX mode.
Note :
If the SHUTTER menu is set to fi xed electronic shutter
mode, the SENS-UP menu will not be available. If FLICKERLESS is set to ON, the FIX mode of the SENS-
UP menu will be disabled. If the SHUTTER menu is set to AUTO, the SENS-UP
menu can be set to either OFF or AUTO mode.
20 – DIGITAL COLOR DOME CAMERA
If set to ON, the shutter speed will be fi xed to 1/100(PAL:1/120) second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting.
Note :
If the SHUTTER menu is set to AUTO or FIX mode, the
FLICKERLESS menu will not be available. If the SENS-UP function is set to FIX mode, the Flickerless
menu will be deactivated. If AGC is set to FIX mode, the FLICKERLESS function will
be disabled.
XDR (eXtended Dynamic Range)
[OFF, LOW, MID, HIGH]
Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.
Select one from OFF, LOW, MID and HIGH. Closing to HIGH will increase the compensation level.
DAY/NIGHT
DAY
If set to DAY, it will be fi xed to DAY mode regardless of the ambient conditions.
NIGHT
If set to NIGHT, it will be fi xed to Black-and-White mode regardless of the ambient conditions.
[DAY,NIGHT,AUTO]
If you press the SETUP switch with a NIGHT sub menu selected, you will see a menu where you can set Burst to OFF/ON. If BURST is set to ON, the Burst signal will output together with the black-and-white composite video signal. If BURST is set to OFF, the Burst signal does not output. You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.
AUTO
The camera will automatically switch between DAY and NIGHT mode, according to the lighting condition.
If you press the SETUP switch with an AUTO­based sub menu selected, you will see the appropriate screen.
AUTO
BURST OFF DAYÆNIGHT BRIGHTNESS MID DWELL TIME 2S NIGHTÆDAY BRIGHTNESS MID DWELL TIME 5S MASK AREA 1 2
You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.
The BRIGHTNESS of DAYÆNIGHT sets the brightness degree of color to BW switching,
How to use OSD Menu
for which you can select from LOW, MID, and HIGH. As you adjust it from HIGH to LOW, the
screen switches to black and white mode under the darker situation. DWELL TIME of DAYÆNIGHT sets the time to maintain switched black and white mode.
The BRIGHTNESS of NIGHTÆDAY sets the brightness degree of BW to color switching, for which you can select from LOW, MID, and HIGH. As you adjust it from HIGH to LOW, the screen switches to color mode under the darker situation.
DWELL TIME of NIGHTÆDAY sets the time to maintain switched color mode.
The MASK AREA menu is used to prevent unintended mode switching or inability of determining the switching due to existence of high spot light source at night.
If you press the SETUP switch in item 1 or 2 of the MASK AREA menu, you will see a menu where you can specify an area to MASK.
MASK AREA
<SIZE>  <LOCATION>
English 21
ENG
How to use OSD Menu
NIGHT
You can specify MASK 1 and 2 simultaneously. The MASK is only for determining the mode switching, and any excessive bright area at night will be excluded by the confi gured MASK.
Note :
If BACKLIGHT is set to BLC, the MASK AREA function will be deactivated.
WHITE BAL [DAY/NIGHT]
If you want to adjust the color scheme, use the
WHITE BALANCE function.
DAY
In DAY mode, you can set the color values of RED and BLUE. The screen will be displayed in
colors according to your settings.
WHITE BAL
DAY/NIGHT DAY MODE AWC RED [00]----I---­ BLUE [00]----I---­ R-GAIN [0248] B-GAIN [0247]
Note :
You can set the values of R-GAIN and B-GAIN only in
AWC mode.
22 – DIGITAL COLOR DOME CAMERA
Use the NIGHT mode if you want to set the white balance differently according to the ambient luminance.
If the NIGHT mode is set to OFF, the white balance will always operate as set in DAY mode; if not to OFF, the camera will switch to as set in DAY/NIGHT mode according to the brightness.
In NIGHT mode, you can set the values of RED, BLUE and BRIGHTNESS. The screen will be displayed in colors according to your settings.
DAY/NIGHT NIGHT BRIGHTNESS MID MODE AWC RED [00]----I---­ BLUE [00]----I---­ R-GAIN [0248] B-GAIN [0247]
Note :
You can set the values of R-GAIN and B-GAIN only in
AWC mode. If AGC is set to OFF or FIX, you can not access the
NIGHT menu.
For adjusting the white balance, the following 5 modes are provided:
WHITE BAL
How to use OSD Menu
ATW1(Auto Tracing White Balance mode
1): The camera can automatically adjust the color temperature in real time, according to the ambient conditions. The color temperature ranges from approx. 2500K to 9300K.
ATW2: The color temperature ranges from
approx. 2,000K to 10,000K. AWC ( Auto White Balance Control): If you
press the SETUP switch in the appropriate item position, Auto White Balance will perform once.
3200K : Set color temperature to 3200K
5600K : Set color temperature to 5600K
RED : Adjusts the strength of the red color.
BLUE : Adjusts the strength of the blue color.
R-GAIN/B-GAIN : Enables you to set the current
color temperature manually. BRIGHTNESS : Select a brightness level in
switching from setting in DAY mode to setting in NIGHT mode.
DIGITAL ZOOM [ON/OFF]
You can set the digital zoom factor and position. If you press the SETUP switch with the DIGITAL ZOOM function set to ON, you will see the appropriate screen.
When the zoom factor and position are defi ned, the digital zoom function will operate.
DIGITAL ZOOM
RATIO [X1.0] < LOCATION >
-
LOCATION : If you press the SETUP switch in the condition where the image is enlarged as much as the ratio setting, you can watch an invisible area of the effective screen as well using the
Note :
If the digital zoom factor is set to larger than 1x, the FENCE
function will be deactivated. The DIGITAL ZOOM function enlarges the pixel itself, which can cause deterioration of the quality.
DETAIL [0~3]
Controls the horizontal or vertical distinction.
V-SYNC [INT, LINE]
Select the vertical sync mode for INT or LINE. If you select INT, the camera will use the internal
synchronization. If selecting LINE, the camera will use the external
power source frequency for the synchronization. You can adjust the LL-PHASE.
cdef
switch.
English 23
ENG
How to use OSD Menu
Note :
Use of DC 12V will fi x V-SYNC to INT, which can not be
changed.
AGC COLOR SUP [LOW , MID, HIGH]
Adjust the color scheme according to the AGC value.
REVERSE [OFF, H, V, H/V]
Mirrors video signals horizontally, vertically, or both.
POSI/NEGA [+, -]
Output as it is or mirror the video brightness signal.
PIP [OFF, ON]
Displays a sub image together with the main image on the same screen using the Picture In Picture function.
Note :
If more than one privacy zone is set and the PRIVACY
SET is set to ON, the PIP function will be deactivated. If the INTELLIGENCE function is set to FENCE mode, the
PIP menu will be deactivated.
DIS [OFF, ON]
Digital Image Stabilization will set the anti-shake compensation.
24 – DIGITAL COLOR DOME CAMERA
Note :
If you set DIS to ON, the compensation area will be
enlarged as set in the digital zoom factor. If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS function will be deactivated.
INTELLIGENCE
MOTION OFF ADVANCED OFF MASK AREA DISPLAY ON SENSITIVITY [4] RESOLUTION [5]
You can set the motion detection and tracking in the
INTELLIGENCE menu.
MOTION
TRACKING
Detects and tracks a moving object.
DETECTION
Detects a moving object.
Note :
If it is set to DETECTION, you can not set such functions as
FIXED/MOVED and FENCE in the ADVANCED menu.
eINTELLIGENCEf
1 2 3 4
[OFF,TRACKING,DETECTION]
How to use OSD Menu
ADVANCED
Detects a motion of an object and displays an image of any moving object before tracking the moving route.
FENCE
This is to detect if a moving object passes through the specifi ed LINE or AREA.
In a condition where a moving object is detected in an analysis of the previous and current frames whose movement overlaps a certain area, the system displays “PASS” if the object’s center line passes through the line while it displays “ENTER” or “EXIT” if the center point passes through the area.
LINE OFF AREA OFF
You can set the position and detection direction of the
LINE, and the size and position of the AREA.
[OFF, FIXED/MOVED, FENCE]
FENCE
- How to set the line
LINE
PIXEL LEVEL [4] <POINT>
DIRECTION §¨
If you press the SETUP switch with the LINE
option set to ON, you can specify the position and detection direction of the line.
If you change the PIXEL LEVEL for setting
the position, specify the pixel that moves by a single pressure of the
In <POINT>, you can specify the fi rst position of the line by pressing the SETUP switch once, and the second position by pressing the switch again. Use the
cdef
position. Set each position of the two points and press the SETUP switch to complete the positioning.
If you change the DIRECTION, you can specify the detection direction. The detection direction based on the defi ned two points will be displayed on the screen.
cdef
switch.
switch to specify the
English 25
ENG
How to use OSD Menu
- How to set the area
AREA PIXEL LEVEL [4] <SIZE>  <LOCATION>
If you press the SETUP switch with the AREA
option set to ON, you can specify the position and size of the area.
If you change the PIXEL LEVEL for setting
the position, specify the pixel that moves by a single pressure of the
In <SIZE>, press the SETUP switch and use the
cdef
Press the SETUP switch again to complete the sizing.
In <LOCATION>, press the SETUP switch and use the
cdef
Press the SETUP switch again to complete the positioning.
Note :
If you set the LINE of the FENCE to ON, PRIVACY 12 will
not be available. Functions of FENCE, PIP, DIS and DIGITAL ZOOM (if the digital zoom factor is set to larger than 1x) can not be
cdef
switch.
switch to adjust the size.
switch to specify the position.
26 – DIGITAL COLOR DOME CAMERA
used simultaneously.
In the boundary of the defi ned AREA and LINE, a FENCE detection error may occur if two or more moving objects overlap with each other or one object separates in multiple directions.
FIXED/MOVED
If an object on the screen suddenly disappears or an object comes out of nowhere and stays for a certain time, the area will be displayed.
A detection (FIXED/MOVED) error may occur if :
- multiple motions occur continuously in random directions
- a fi xed object moves in one position continuously
- a second object screens the fi rst moving object
MASK AREA [1~4]
Specify a detection exception area to mask. Select a mask number and specify the size and
position.
<SIZE>  <LOCATION>
MASK AREA
How to use OSD Menu
DISPLAY [ON, OFF]
With the DISPLAY option set to ON, a motion or a set ADVANCED function will be displayed on the screen, if detected.
SENSITIVITY [1~7]
Set the sensitivity of the motion detection.
RESOLUTION [1~5]
If setting it to high, the camera can detect even a trivial movement of the target.
PRIVACY ZONE SETUP
ePRIVACY ZONEf
1 2 3 4 5 6 7 8 9 10 11
PRIVACY SET ON STYLE
The PRIVACY function will protect your privacy by screening the privacy area that you have specifi ed during monitoring. You can specify up to 12 privacy zones.
12
MOSAIC1
If you set the PRIVACY SET to ON, your PRIVACY ZONE settings will be applied.
You can change the style to adjust the mosaic size and color of the PRIVACY ZONE.
ePRIVACY ZONEf
1 2 3 4 5 6 7 8 9 10 11
PRIVACY SET ON STYLE COLOR Y-LEVEL [128] RED [128] BLUE [128]
Use the
cdef
PRIVACY 1 through 12. Select one from PRIVACY 1~12 and press the
SETUP switch to confi rm your setting. You can specify a pixel that moves as you change the PIXEL LEVEL to set the position.
switch to select one from
PRIVACY ZONE SET1
PIXEL LEVEL [4] <POINT> <POSITION>
12
English 27
ENG
How to use OSD Menu
- How to set the point
You can set each position of the 4 points.
If you press the SETUP switch in <POINT>,
you will see the points available in the
PRIVACY ZONE. Each time you press the SETUP switch, the points available will move.
Use the
cdef
of each point. Set each position of the four points and press the SETUP switch to complete the positioning.
- How to set the position You can move the position of the overall area.
By pressing the SETUP switch in
<POSITION>, you can move the overall
position of the privacy zone.
Use the
position and press the SETUP switch to confi rm it.
Note :
If more than one PRIVACY ZONE is specifi ed and the
PRIVACY SET is set to ON, the PIP function will be deactivated.
If the 12th PRIVACY ZONE is specifi ed, the LINE function
of FENCE will be deactivated.
switch to set the position
cdef
switch to move the
28 – DIGITAL COLOR DOME CAMERA
OTHER SET
FACTORY DEFAULTS OSD COLOR BW
FACTORY DEFAULTS
All the settings will be restored to the factory default.
OSD COLOR [BW, R/G/B]
You can set the OSD(On-screen Display) color to COLOR or B/W.
eOTHER SETf
How to use OSD Menu
SYSTEM INFORMATION
eSYSTEM INFOf
TYPE 3_VAR_NOR_N SERIAL NO. CAMERA VER. 0.50_090101
You can check the system information such as SERIAL NO and CAMERA VER.
LANGUAGE
The camera supports 5 different languages. Select a preferred language.
000000000000000
eLANGUAGEf
ÃENGLISH
PУCCKNЙ
POLSKI
ČESKY
TÜRKÇE
Initial Confi guration Table
Camera Confi guration
CAMERA ID OFF IRIS ALC AGC VERY HIGH MOTION (F.FAST) DNR MID SHUTTER OFF SENS-UP
AUTO x4 FLICKERLESS (OFF) XDR MID DAY/NIGHT AUTO DIGITAL ZOOM OFF DETAIL [2] AGC COLOR SUP MID REVERSE H/V POSI/NEGA + PIP OFF DIS OFF V-SYNC INT
ENG
English 29
Specifi cations
SPECIFICATIONS
Items Sub-items
Camera Type
Image
Scanning
Min. Scene
Illumination
Functions
30 – DIGITAL COLOR DOME CAMERA
Device 1/3” Super-HAD IT CCD
Pixels
System Interlace
Scanning Line 525 lines
Frame 30frame/1sec
Horizontal
Frequency
Vertical
Frequency
Number of Privacy Zone 12 (Polygonal Method)
Motion Detection OFF/Tracking/Detection
eXtended Dynamic Range(XDR) Off/On (Level Setting)
High Speed Shutter 1/60 ~ 1/10Ksec (OSD)
Total 811 x 508
Effective 768 x 494
Internal Mode 15,734 Hz
Line-lock Mode 15,750 Hz
Internal Mode 59.94 Hz
Line-lock Mode 60 Hz
Sens-up F No. Level DAY NIGHT
OFF 1.2 50 IRE 0.4 Lux 0.4 Lux OFF 1.2 30 IRE 0.24 Lux 0.24 Lux
OFF 1.2 15 IRE 0.12 Lux 0.12 Lux 512 times 1.2 50 IRE 0.0008 Lux 0.0008 Lux 512 times 1.2 30 IRE 0.00047 Lux 0.00047 Lux 512 times 1.2 15 IRE 0.00023 Lux 0.00023 Lux
Day/Night DAY/NIGHT/AUTO
D-Zoom x1 ~ x16 (x0.1 STEP)
PIP Off/On
Flickerless Off/On
Sens-Up x2 ~ x512
BLC Off/On (Area Setting)
SCC-B5366N/SCC-B5366SN/SCC-B5368N/SCC-B5368SN
CCTV Camera
Condition Min. Scene illumination
Loading...
+ 146 hidden pages