SC20F70 Series
SC07F70 Series
Vacuum Cleaner
user manual
✻ Before operating this unit, please read the instructions carefully.
✻ For indoor use only.
Thank you for purchasing a Samsung product.
To receive a more complete service,
please register your product at
www.samsung.com/register
English
CLEAN THE DUST BIN WITH WATER
1 2 3 4
Take the dust bin out by
lifing the handle
Push the button aside. Turn the grille and take
5 6 7
Separate the dust bin
from body.
Clean the dust bin and
body with water.
ACCESSORY (OPTION)
• Pull out the button, to use the dusting brush.
out it.
Push the button.
Leave the dust bin and
body in the shade until
completely dry.
• To use the crevice tool, push the accessory on to the end of the hose handle in the opposite
direction.
safety information
SAFETY INFORMATION
• Before operating the appliance, please read this manual thoroughly and retain it for your
WARNING
WARNING
CAUTION/WARNING SYMBOLS USED
reference.
• Because these following operating instructions cover various models, the characteristics of
your vacuum cleaner may differ slightly from those described in this manual.
WARNING
CAUTION
Indicates that a danger of death or serious injury exists.
Indicates that a risk of personal injury or material damage exists.
OTHER SYMBOLS USED
Represents something you must NOT do.
Represents something you must follow.
Indicates that you must disconnect the power plug from the socket.
WARNING
This vacuum cleaner is designed for household use only.
Do not use this vacuum cleaner to clean building waste and debris.
Regularly keep the filters in clean conditions to prevent of collecting fine dust in them.
Do not use this vacuum cleaner with any of the filters removed.
Failure to meet these requirements could cause damage to the internal parts and void
your warranty.
safety information _03
IMPORTANT SAFEGUARDS
GENERAL
• Read all instructions carefully. Before switching on, make sure
that the voltage of your electricity supply is the same as that
indicated on the rating plate on the bottom of the cleaner.
• WARNING : Do not use the vacuum cleaner when rug or floor is
wet. Do not use to suck up water.
• Close supervision is necessary when any appliance is used by
or near children. Do not allow the vacuum cleaner to be used
as a toy. Do not allow the vacuum cleaner to run unattended at
any time. Use the vacuum cleaner only for its intended use as
described in these instructions.
• Do not use the vacuum cleaner without a dust bin.
Empty the dust bin before it is full in order to maintain the best
efficiency.
• Do not use the vacuum cleaner to pick up matches, live ashes or
cigarette butts. Keep the vacuum cleaner away from stoves and
other heat sources. Heat can deform and discolour the plastic
parts of the unit.
• Avoid picking up hard, sharp objects with the vacuum cleaner as
they may damage the cleaner parts.
Do not stand on the hose assembly. Do not put weight on the
hose.
Do not block the suction or the exhaust port.
• Switch the vacuum cleaner off on the body of the machine
before unplugging from the electrical outlet. Disconnect the plug
from the electrical outlet before emptying the dust bin. To avoid
damage, please remove the plug by grasping the plug itself, not
by pulling on the cord.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
04_ safety information
safety information
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
• Children should be supervised to ensure that they do not play
with the appliance.
• The plug must be removed from the socket outlet before
cleaning or maintaining the appliance.
• The use of an extension cord is not recommended.
• If your vacuum cleaner is not operating correctly, switch off the
power supply and consult an authorized service agent.
• If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
• Don’t carry the vacuum cleaner by holding the hose.
Use the handle on the vacuum cleaner set.
• Unplug the cleaner when not in use.
Turn off the power switch before unplugging.
UV BRUSH
• Since the UV rays from the UV Brush damage skin and eyes,
never allow the rays to make contact with skin or eyes and do
not let children or the elderly use the UV Brush. It may damage
your eyesight.
• If the transparent window is broken and the UV rays are exposed
directly, turn the power off and contact the service center.
• Do not use the UV Brush for purposes other than the sterilization
of mattresses, bedclothes, beds, cushions and so on made from
material. The company will not be held liable for any loss due to
accidents from using the UV Brush for purposes other than its
original purpose as listed above.
safety information _05
• Do not sit on the UV Brush or drop it, and avoid imparting
impacts on the product. Failing to do so may result in injury or
product damage.
• Do not touch the power terminals on the back of the UV Brush
with a metal pin or rod. This may result in electric shock or fire.
• When the UV lamp is out of order, never disassemble or modify
the product yourself.
Please contact the manufacturer or service center for a
replacement.
• Since an internal discharge occurs within the UV Brush, never
use the product near an inflammable spray or substance.
• Take care not to touch the UV lamp window after using the
UV Brush for an extended period of time as the surface of the
window may be hot.
• The UV Brush may start slowly at a low temperature due to the
inherent characteristics of UV lamps. Please keep the UV Brush
indoors.
06_ safety information
contents
ASSEMBLING THE CLEANER
08
OPERATING THE CLEANER
09
TOOLS AND MAINTENANCE
FILTER
15
TROUBLESHOOTING
26
09 Power cord
09 ON/OFF Switch
10 Power control
12 Using the UV brush (SC20F70U Series)
13 Using the Dust Sensor (Option)
15 Using accessory
17 Maintain floor tools
20 Cleaning the Dust Sensor (Option)
20 Emptying the dust bin
21 Clean the Grille
22 Clean the dust bin with water
23 Cleaning the dust filter
24 Cleaning the dust filter
25 Cleaning the outlet filter
contents _07
assembling the cleaner
OPTION
• For storage, park the floor nozzle.
Please do not pick up a machine while the floor
nozzle parked
08_ assembling the cleaner
operating the cleaner
POWER CORD
• When removing the plug from the electrical outlet, grasp the plug, not the
CAUTION
ON/OFF SWITCH
cord.
02 OPERATING THE CLEANER
operating the cleaner _09
POWER CONTROL
- +
-/+
Hose Handle (SC20F70H Series)
1. ON/OFF [ ] Button
- Press the ON/OFF button to operate the vacuum cleaner.
Press again to stop the vacuum cleaner.
2. [(-/+)] Button
- Press the MODE button repeatedly to select the correct mode.
(ON) MIN → MAX
3. [ ] Button
- Press the [ ] button to operate the vacuum cleaner quietly.
Don’t cover the handle transmitter when you use a
handle control button.
HOSE (SC07F70H Series)
1. ON/OFF [ ] Button
- Press the ON/OFF button to operate the vacuum cleaner.
Press again to stop the vacuum cleaner.
2. [(-)], [(+)] Button
- Press the (+) button to increase the vacuum's suction power.
Press the (-) button to decrease the vacuum's suction power.
Don’t cover the handle transmitter when you use a
handle control button.
If no button is pressed for 30 minutes while cleaning, the
safety device is activated and the power is cut off.
In this case, press the [Power] button on the main unit or
unplug and then plug the power cord in again.
sender
Handle Control
The cleaner is controlled by radio
frequency signals.
sender
Handle Control
The cleaner is controlled by radio
frequency signals.
HOSE (SC20F70U Series)
1. ON/OFF [ ] Button
- Press the [ ] button to operate the vacuum cleaner. Press
again to stop the vacuum cleaner.
2. [SUCTION (-/+)] Button
- Press the [SUCTION (-/+)] button to increase or decrease the
suction power. Each time you press the button, you gradually
increase the suction power. After the suction power reaches its
maximum, the next time you press the button, you return the
suction power to its minimum.
3. [BRUSH ON/OFF] Button
- Press the [BRUSH ON/OFF] button to operate the UV Brush.
Press again to stop the UV Brush.
Don’t cover the handle transmitter when you use a handle control button.
If no button is pressed for 30 minutes while cleaning, the safety device is activated and the
power is cut off.
In this case, press the [Power] button on the main unit or unplug and then plug the power cord
in again.
10_ operating the cleaner
sender
Handle Control
The cleaner is controlled by radio
frequency signals.
operating the cleaner
Change the battery
• When the vacuum cleaner does not work, replace the batteries.
If the problem persists, please contact our authorized dealer.
• Use 2 batteries of size AAA.
02 OPERATING THE CLEANER
CAUTION
1. Never disassemble or recharge the batteries.
2. Never heat up the batteries or throw them into a fire.
3. Do not reverse (+), (-) poles.
4. Dispose of the batteries property.
BATTERY TYPE : AAA Size
BODY
Press the power ON/OFF button repeatedly to start and to stop
the vacuum cleaner. (OFF → ON → OFF)
If the remote handle control is not working, the cleaner
can be operated using the ON/OFF button on the body
of the machine.
1
Before performing this operation, make sure that there is no blockage in the tube, hose or brush.
The ON/OFF button toogles the vacuum between the on and off states.
The filter light is illuminated when the dust pack requires checking or emptying.
2
operating the cleaner _11
USING THE UV BRUSH (SC20F70U SERIES)
1. Insert the brush into the hose handle.
• Insert the UV brush securely into the hose handle until you hear a “clicking”
sound.
2. Press the [BRUSH ON/OFF] button to start cleaning.
• Press the [BRUSH ON/OFF] button and choose the appropriate
suction strength for the cleaner.
• It is advisable to select the (Max) suction strength setting.
• UV sterilization cannot be activated by itself.
3. When you have finished UV cleaning, press the [ ] button.
• Press the [ ] button to stop the cleaner.
- For safety reasons, UV brushing only runs for 30 minutes and then stops
operating. To resume the operation, press the [SUCTION (-/+)] button again.
CAUTION
12_ operating the cleaner
The UV brush, which is inserted into the hose handle (not directly connected to the telescopic
pipe), is dedicated for bedclothes.
operating the cleaner
USING THE DUST SENSOR (OPTION)
Dust Sensor Operations
• Indicates the amount of sucked in
dust so that users can experience
the successful operation of the
product while cleaning the room.
• The dust sensor is automatically turned on when the cleaner runs and turned off when the cleaner is
stopped.
• Since the dust sensor runs on battery power, there is no separate switch.
Installing the Batteries
• Green : When the amount of
sucked in dust is small.
• Red : When the amount of
sucked in dust is large.
02 OPERATING THE CLEANER
1 2 3
• If the dust sensor doesn’t work even after cleaning the sensor, replace the batteries with new ones.
AAA type batteries are required.
• Do not disassemble or recharge the used batteries.
CAUTION
• Do not heat the batteries or put them in a fire.
• Check the polarities (+ ,-) before inserting the batteries.
• Put the used batteries into the battery recycle bin.
• When you are not using the product for an extended period of time, separate the batteries.
Check the polarities
operating the cleaner _13
Cleaning the dust sensor (Option)
• Since the dust sensor consists of sensitive electronic devices, if water or
other liquids enters the sensor, it may cause a problem.
• If you use athe dust sensor without closing the battery compartment
cover, pollutants such as dust may accumulate in the compartment
and cause a problem. Therefore, be sure to use the product with the
compartment cover closed.
• Take care when you use the cleaner because the dust sensor may
malfunction or may break due to an impact.
Installing the Dust Sensor
• Assemble the dust sensor between the air inlet connector on the neck of
the brush and the extension pipe. (Recommended)
You can assemble the dust sensor between the extension pipe and the
hose.
Dust Sensor (2 EA)
The assembly position of
the dust sensor
14_ operating the cleaner
tools and maintenance filter
USING ACCESSORY
Pipe
• Adjust the length of the telescopic pipe by sliding the length control
button located in the center of the telescopic pipe back and forth.
• To check for blockages, separate the telescopic pipe and adjust to
shorten. This allows for easier removal of waste clogging the tube.
Accessory (Option)
• Pull out the button, to use the dusting brush.
03
TOOLS AND MAINTENANCE FILTER
• To use the crevice tool, push the accessory on to
the end of the hose handle in the opposite direction.
tools and maintenance filter _15
Accessories (SC20F70U Series)
• Push the accessory onto the end of the hose
handle.
• Pull out the dusting brush to use the crevice tool.
• Push the accessory onto the end of the pipe.
• Pull out the dusting brush to use the crevice
tool.
Accessory (Option)
• Furniture brush for desk, Furniture and Floor.
16_ tools and maintenance filter
tools and maintenance filter
MAINTAIN FLOOR TOOLS
2-Step Brush
Carpet Cleaning Floor Cleaning
• Adjust the inlet lever according to the floor surface.
• Remove waste matter completely if the inlet is blocked.
Power Pet Plus Brush (Option)
03
TOOLS AND MAINTENANCE FILTER
1 2
For improved pickup
of pet hair and fibre on
carpets.
Frequent vacuuming of hair or pet fur may cause a falling-off of the rotation due to matters tangled around
the drum. In this case, clean the drum with care.
1. Push the Open button of the transparent screen cover to separate the cover.
2. Remove the brushbar from the transparent screen.
3. Remove waste matter such as dust and hair tangled around the brushbar using scissors.
4. Remove dust inside the brush housing using a dry duster or crevice tool.
5. Insert brushbar into rotating belt and assemble.
6. Click the transparent screen cover back into place to reassemble.
4 5
3
6
Parquet Master Brush (Option)
• Vacuum dust in wide area at once.
• Remove waste matter completely if the inlet is
blocked.
tools and maintenance filter _17
Mini turbo brush (Option)
- To replace brushroll
1. If a clog is present or debris is visible, unscrew the two screws on
the back of the Mini turbo brush to remove the faceplate and clear
any obstructions.
2. Inspect condition of brushroll.
Replace brushroll if brushes are worn down.
To remove brushroll, pull up and out of end slots in nozzle housing.
Insert ends of brushroll into same slots to replace.
Inspect belt to ensure that it is in good condition.
If belt is broken or cracked, replace belt according to To Replace
Belt instructions.
3. Using at MAX.
Press the MAX button to operate the vacuum at maximum intake.
- To replace belt
1. Remove bottom plate.
See figure in To Replace Brushroll instructions.
2. Loop one end of new belt around shaft of pulley.
3. Loop other end of belt around designated area for it on brushroll.
Insert brushroll into slots in nozzle housing.
See figure in To Replace Brushroll instructions.
4. Fit Mini turbo brush back together as described in To Replace
Brushroll instructions.
18_ tools and maintenance filter
tools and maintenance filter
To remove dust from the dust bin of the UV brush (Option)
When you notice that the dust bin is filled, use the [Dust Removal] button to empty the dust bin.
1. To remove dust from the dust bin, move the [Dust Removal] button
to the “Open” position.
- While the cleaner is operating (suction), use the [Dust Removal]
button for this purpose.
2. When done, move the [Dust Removal] button to the “Close”
position.
- When the [Dust Removal] button is in the “Open” position, the
suction power of the cleaner is reduced.
Cleaning the UV brush (Cleaning the drum) (Option)
Human and pet hair often becomes tangled in the drum, causing a reduction in the rotary power of the
the drum. To prevent this, clean the drum on a regular basis. Before the operations make sure that UV
brush is off.
1. Push the [Open Transparent Cover] button inward to remove the
cover.
03
TOOLS AND MAINTENANCE FILTER
2. Use the crevice tool to remove impurities such as dust and hair
from around the drum.
3. When done, push the [Open Transparent Cover] button outward to
close the cover.
tools and maintenance filter _19
CLEANING THE DUST SENSOR (OPTION)
If the green light is not lit while cleaning
• Check if the hose, extension pipe or the air inlet is clogged and clean it if
necessary.
• Empty the dust bin of the cleaner or clean the filters.
If the red light does not light up when cleaning a dusty
location
• Clean the sensors (2EA) in the dust sensor block with a dry cloth.
CAUTION
Take care when you clean the sensors in the dust sensor block so that the sensors are not
damaged.
EMPTYING THE DUST BIN
1 2 3
Once dust reaches the dust full
mark, empty the dust bin.
4 5 6
Take the dust bin out by lifing
the handle
Push the button aside.
Click
Throw the dust away in the bin. Close the dust bin cover.
20_ tools and maintenance filter
Before use, push the dust
bin into the main body of the
vacuum cleaner until you hear
the “click” sound.
tools and maintenance filter
CLEAN THE GRILLE
1 2
Push the button aside. Turn the grille and take out it. Brush away the dust.
4 5
Insert the grille back into the
dust bin and turn the grille.
Close the dust bin cover.
3
03
TOOLS AND MAINTENANCE FILTER
tools and maintenance filter _21
CLEAN THE DUST BIN WITH WATER
1 2 3
Push the button aside. Turn the grille and take out it. Push the button.
4 5 6
Separate the dust bin from
body.
You may rinse the dust bin with cold water.
22_ tools and maintenance filter
Clean the dust bin and body
with water.
Leave the dust bin and body in
the shade until completely dry.
tools and maintenance filter
CLEANING THE DUST FILTER
When to clean the dust filter
• If the dust filter is very dirty outside or clogged with fine dust, then
clean it.
• The lamp will turn red when suction is reduced. If the light comes on
after emptying the dust bin, cleaning the grill, please check the dust
filter.
When suction is noticeably reduced or vacuum cleaner abnormally overheats, please clean the
dust filter.
03
TOOLS AND MAINTENANCE FILTER
tools and maintenance filter _23
CLEANING THE DUST FILTER
1 2 3
Take the dust bin out by lifing
the handle.
Pull the dust bin cover to open.
4 5 6
Shake the filter over a garabage
can to remove loose dust, then
wash the filter with water.
Let the filter dry in the shade for
more than 12 hours.
7
Close the dust bin cover.
Make sure the filter is completely dry before putting it back into the
vacuum cleaner. Allow 12 hours for it to dry.
Do not use wet filter.
If dust filter is damaged or deformed please replace it.
To close the dust bin cover,
filter should be assembled.
Remove the filter from the dust
bin.
Put the filter into the dust bin.
8
After the take the dust bin in
main body, close the cover
dust when you hear the " click"
sound.
24_ tools and maintenance filter
CLEANING THE OUTLET FILTER
1 2 3
03
TOOLS AND MAINTENANCE FILTER
Take the dust bin out by lifing
the handle.
Pull out the HEPA filter.
Separate the filter and holder
by pulling.
4 5 6
Throw away the dirty filter.
• When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats,
please clean the outlet filter. Note. Do not wash HEPA filter.
If cleaning does not resolve the problem Please replace blocked out filter.
• Replacement filters are available at your local Samsung distributor.
Assemble the new filter in
holder.
Assemble the filter and holder
in main body.
tools and maintenance filter _25
troubleshooting
PROBLEM SOLUTION
Motor does not start.
Suction force is gradually
decreasing.
Cord does not rewind
fully.
Vacuum cleaner dows not
pick up dirt.
Low or decreasing
suction.
Body overheating. • Please check filters, if required clean as illustrated in the instruction.
Static electicity
discharge.
• Check cable, pulg and socket.
• Leave to cool.
• Check for blockage and remove.
• Pull the cord out 2-3m and push down the cord rewind button.
• Check hose and replace if required.
• Please check filter and, if required, clean as illustrated in the
instructions. if filters are out of condition change them to new ones.
• Please decrease power suction.
• This can also occur when air in the room is very dry.
Please ventilate the room till air humidity becomes normal.
26_ troubleshooting
memo
Code No. DJ68-00701F REV(0.0)
Loading...