Samsung SBP-300NBW User Manual

INSTALLATION BOX

User Manual

SBP-300NB (IVORY)

SBP-300NBW (WHITE)

INSTALLATION BOX

User Manual

Copyright

Hanwha Techwin

©2019

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

Co., Ltd. All ri ghts reser ved.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Hanwha Techwin

reserves the

overview

CONTENTS

OVERVIEW

3

INSTALLATION & CONNECTION

6

APPENDIX

12

4 What’s Included

6 Installation

12 Specification
12 Product Overview

English _3

overview

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name Quantity

4_ overview

INSTALLATION BOX

INSTALL BRACKET

Gasket (for SBP-300WM1/WMW1)

Gasket (for SBP-300WM/WMW)

RUBBER HOUSING

BRACKET ADAPTOR

1

1

1

1

1

1

Appearance Item Name Quantity

MOUNT CAP

MOUNT CAP fastener 1

M10 x L22 screw (to attach the install bracket)

M8 x L20 screw (to attach the housing)

M3 x L6 screw

(to attach the bracket adaptor and media convert)

M10 x L12 wrench bolt (to attach SBP-300WM/WMW) 4

M10 x L20 wrench bolt (to attach SBP-300WM1/WMW1) 4

M4 x L8 screw (to attach the media convert) 2

5

4

4

4

English _5

installation & connection

INSTALLATION

1. Push the locking lever on the door to separate the housing and door.

LOCKING
LEVER

LOCKING LEVER

2. Undo the four screws to separate the bracket adaptor.
Lock the unused piping hole with the attached mount cap.
Use a mount cap fastener to attach the mount cap.

Mount cap
BRACKET
ADAPTOR

fastener

DOOR

HOUSING

Mount cap

6_ installation & connection

3. Remove the double-sided tap on the rear side of the gasket and affix it to the door.
Attach the wall mount to the door using the four M10 screws.
< Tighten each of the four screws a little at a time so that the wall mount is evenly pressed
to the gasket. >

• Use of SBP-300WM1/SBP-300WMW1 wall mount (with M10 x L20 screws)

DOOR

• Use of SBP-300WM/SBP-300WMW wall mount (evenly securing the wall mount
inside the gasket groove as shown in the image below.) (with M10 x L12 screws)

DOOR

GASKET

GASKET

GASKET

J

Please assemble
the set in such a
way that the lock tab
faces down into the
slot in the installation
direction.

English _7

installation & connection

4. Attach the install bracket to the wall, corner mount (SBP-300KM/SBP-300KMW) or pole mount
(SBP-300PM/SBP-300PMW) using the M10 screws.
Only use the 4 screws included in the accessories as shown in the image below.

Screw (circular head, with M10 x L22 screw)

• Installation on the wall

• Pole Mount

• Corner Mount

8_ installation & connection

5. Place the housing on the install bracket as shown in the image.

To install it on the wall, attach the rubber housing as shown in the figure.

`

The rubber is not waterproof. It is decorative only, serving to hide a gap.
Therefore, if the cable is inserted into the main body separately and not through the duct on the wall, the insertion
point of the cable must be completely waterproof.
If this is not done, any water leaks may cause problems.

Waterproofing

needed

Cable

6. Secure the housing to the install bracket using 4 M8 screws in the same ways as "No. 4" in the

installation procedure.

English _9

installation & connection

7. Insert the external cable into the main body using a pipe.
Wrap the thread of the pipe screw with Teflon tape to protect against water leakage problems.
(Make sure that water leaks will not cause a problem at the cable insertion point.)

CABLE

Teflon tape

8.

Install the power adaptor and media converter using the bracket adaptor, and connect the external cable.

Power

adaptor

BRACKET ADAPTOR

MEDIA CONVERTER

10_ installation & connection

9. Pull the cable out through the door and wall mount and mount the door on the housing.

(Return the locking lever to its original position and check that the hinge is properly attached to the
housing.)

LOCKING LEVER

Wall Mount

HOUSING

LOCKING LEVER

10. Fasten the door to the housing using a hexagonal wrench. (Tighten the screws while pressing the

door with your hand as shown in the image below. Then tighten each of the screws a little at a
time to make sure that the door is tightly pressed to the housing.)

Cable

DOOR

English _11

appendix

SPECIFICATION

Items Description

Dimensions (mm) W185.0 x D221.0 x H94.3 (mm)

Weight 3.4kg

Material STEEL, ALUMINUM, SILICON

PRODUCT OVERVIEW

Unit : mm (inch)

12_ appendix

Head Oce

6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : [phone] Fax : [phone]
www.hanwha-security.com

Hanwha Techwin America

500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax [phone]
www.hanwhasecurity.com

Hanwha Techwin Europe

Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel [phone] Fax [phone]
www.hanwha-security.eu