
SPEED DOME CAMERA
Samsung-T Protocol User's Manual
Ver
Ver 1111....88880000EEEE
VerVer
REV.
1.80E
July
2011
Samsung Techwin Co., Ltd.
Security Solution Division
Copyright(c)
1996-2011
SAMSUNGTECHWIN CO.,LTD

Ver
Ver 1111....88880000EEEE
VerVer
Preface
Samsung Techwin S-Protocol is Samsung Techwin's proprietary intellectual property protected by
copyright law. All copy, reprint, and translation to other languages asapart of or all contents of this
user's manual without permission of Samsung Techwin Co. Ltd. are expressly prohibited except for
fair use within the scope of copyright law.
The contents of this manual may change without prior notice for the improvement of product perfor
mance.The design and specifications of Samsung Techwin’sproducts compatible with this protocol
also may change without prior notice for the improvement of product performance. Samsung Techwin
shall not be liable, directly or indirectly, for any injury, loss, or damage caused by or alleged to be
caused by or in connection with the use of the product.
Users are solely responsible for using the product and this user’smanual as Samsung Techwin
exercises no control over the use of this manual.
Document Revision Information
Date Description Note
2009,02,21 -
2009,03,17 -
2009,04,27
2009,06,30
2009.09.17
2010.08.13
2010.11.08
2011.03.31
Updated toanew document format Ver
English version published Ver
Added'PTZ Trace stop' and'Target Lock on' of the second chapter.
-
Added'Track protocol'.
-
Modified errors and Tilt Ranges.
-
PTZ Trace top deleted.
-
Digital Zoom calculation added.
-
Revised notation errors of
-
Revised notation errors of
-
Added
-
Protocol name is changed as'Samsung-T'
-
Revised notation errors of
-
Added parameters about SCP-2120/3120
-
Revised notation error of
-
-In'2,9','2.10',
of SCU-2370 Series
-In'2,9','2.10',
of SCP-2370/2330/2270/3370 Series
-In'2.11',
Series
command.
'2.11'
Added Position Range and Zoom Range
Added Position Range and Zoom Range
Added Special Command2 of SCP-2370/2330/2270/3370
'2.8',2.9'
'2.10.6'
'3.
'2.1'
command.
command.
Protocol Samples'
command
Ver
Ver
Ver
Ver
Ver
Ver
1.10
1.10E
1.20E
1.30E
1.40E
1.50E
1.60E
1.70E
-
2011.07.25
Added
-
Added
-
'2.11.2'
'2.12'
Call PTZ Position Command
New Protocol
Ver
1.80E

Ver
Ver 1111....88880000EEEE
VerVer
Table of Contents>
<
1.Protocol Frame Structure.....................................................................................................................3
1.1 Transmission Packet Format..................................................................................................3
1.2.Communication Timing Chart..................................................................................................3
1.3.Transmission Packet Format.................................................................................................. 4
2.Command................................................................................................................................................ 5
2.1 Pan/Tilt/Zoom/Focus/Brightness............................................................................................ 5
2.2 OSD Menu Control.................................................................................................................. 5
2.3 Preset Control......................................................................................................................... 6
2.4 Product Initialization................................................................................................................6
2.5 Swing ...................................................................................................................................... 7
2.6 Sequence Command................................................................................................................ 7
2.7 PTZ Trace................................................................................................................................8
2.8 Set Pan/Tilt Position Move 1(Relative Movement)............................................................. 8
2.9 Set Pan/Tilt Position Move 2(Relative Movement)............................................................. 9
2.10 Special Command................................................................................................................ 10
2.11 Special Command 2.............................................................................................................13
2.11.1 Move PTZ Position and Track On/Off(Abs. position move)....................................... 13
2.12 New Protocol.......................................................................................................................15
3.Protocol Samples.................................................................................................................................17
3.Appendix...............................................................................................................................................18
3.1.SCP-3120 Digital Zoom Parameter..................................................................................... 18

Protocol Frame Structure
1.
Transmission Packet Format
1.1
Ver
Ver 1111....88880000EEEE
VerVer
Mode
-
Transmit Direction:Simplex/Half duplex
-
Start bit
-
Data bit
-
Parity bit
-
Stop bit
-
Baud rate
-
Communication Timing Chart
1.2.
RS-485/RS-422 Asynchronous Communication
:
bit
:1
bits
:8
None
:
bit
:1
bps
:9600
Pic1.Pan/Tilt Operation Timing Chart
Please note that the Preset commands sendaresponse only at the end of their executions.
The recommended minimum period of control signal communications is70ms.
For the Pan/Tilt operation, setting up the communication period shorter than the recommendation
may cause protocol loss or extend the response time of the camera.
Pic2.Other Commands Timing Chart
Aside from Pan/Tilt, other protocols sendaresponse at the end of their executions depending on
the situation; the response time of the camera may take up to7seconds.

Transmission Packet Format
1.3.
Command Packet Format
<
Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8 Byte9 Byte10 Byte11
STX Cam ID Host ID Cmd1 Cmd2 Data1 Data2 Data3 Data4 ETX Checksum
STX(Start of Text): A0h
-
ETX(End of Text): AFh
-
Cam ID: Dome ID(01h~FFh)
-
Host ID: Host Controller ID(default:00h)
-
Checksum: The value of Modulo
-
>
equal toatotal of Byte2 to Byte9
256
processed by'Logical Not(~)'
Checksum
Return Packet Format
<
Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte
STX Host ID Cam ID Cmd1 Cmd2 Data1 Data2 Data3 Error ETX Checksum
>
= ~((
Byte
2 +……+
Byte
9) &
FFh)
Byte9 Byte10 Byte11
8
Ver
Ver 1111....88880000EEEE
VerVer
Host ID:Controller ID
-
Cam ID:Dome ID Number
-
Error:Bit error codes are listed in the chart below.
-
Description
bit7
bit6
bit5 Camera Module Failure
bit4 Pan/Tilt Failure
bit3 RAM of EEPROM Error
bit2
bit1
bit0 Unsuitable Data

Command
2.
Pan/Tilt/Zoom/Focus/Brightness
2.1
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Direction1 Direction2 Pan Speed Tilt Speed
Zoom Speed
Focus Speed
/
The frame above is located at Byte4 to Byte9 in the command packet.
Direction1~2
-
:
Direction1 is to process the Brightness and Focus commands.
Command1
bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
* * *
Brighter Darker
*
XXh
Focus Near Focus Far
Ver
Ver 1111....88880000EEEE
VerVer
Diredtion2 is to process the Zoom, Pan and Tilt commands as shown in the chart below
Command2
bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
Zoom Wide Zoom Tele Tilt Down Tilt Up Pan Left Pan Right always
Note
For these commands, bit0 must be retained as
:
execute the commands shown in the chart above.
at all times. Changing it to
'0'
'1'
fails to
The speed of Pan, Tilt, Zoom, and Focus is available as shown below.
Pan:00h~3Fh
-
Tilt:00h~3Fh
-
Zoom:01h~08h
-
Focus:10h~80h
-
Note: The function of Zoom/Focus Speed, depending on the product, can not be supported.
Important!: The Zoom and Focus commands cannot be transmitted simultaneously.
OSD Menu Control
2.2
OSD(On Screen Display) Menu On:
2.2.1
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h
B1h
00h 00h 00h 00h
.
0
OSD Menu Off
2.2.2
Cmd1 Cmd2 Data1 Data2 Data3 Data4
B1h
01h 00h 00h 00h
2.2.2
00h
Menu Enter
Cmd1 Cmd2 Data1 Data2 Data3 Data4
01h 00h 06h 00h 00h 00h
The Focus command may be activated automatically in Normal(non-OSD Menu) mode.
*

Menu Cancel(Esc)
2.2.3
Cmd1 Cmd2 Data1 Data2 Data3 Data4
02h 00h 07h 00h 00h 00h
The Focus command may be activated automatically in Normal(non-OSD Menu) mode.
*
Preset Control
2.3
Set Preset(Saves preset commands.)
2.3.1
Send
Receive
Preset Number=0~FEh
:
P1
Clear Preset(Deletes preset commands.)
2.3.2
Send
Receive
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 03h
" " " " "
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 05h
" " " " "
P1
P1
00h 00h 00h
Error
00h 00h 00h
Error
Ver
Ver 1111....88880000EEEE
VerVer
Preset Number=0~FEh
:
P1
Goto Preset(Call saved preset commands.)
2.3.3
Send
Receive
Preset Number=0~FEh
:
P1
The SPD-3300/3000/1000 supports these commands only from0to7Fh.
Product Initialization
2.4
Pan/Tilt Position Initialization
2.4.1
Send
Receive
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 07h
" " " " "
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 0
" " " " "
Dh
P1
00h 00h 00h 00h
00h 00h 00h
Error
Error
Zoom Module Motor Position Initialization
2.4.1
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Receive
00h 0
" " " " "
Fh
00h 00h 00h 00h
Error

Swing
2.5
2.5.1
Send
Return
P1:00h=Pan Swing
P2:
00h ~ 40h
P3:
00h ~ 7
2.5.2
Send
Return
P1:
00=
P2:
00h ~
P3:
00h ~
Set Swing Speed&Time
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 13h
" " " " "
h=Tilt Swing
01
Swing Speed
Fh Swing Dwell Time(0
Set Swing
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 19h
" " " " "
Pan Swing
FEh=First preset position
FEh=Second preset position
h=Tilt Swing
01
P1 P2 P3h
h=Pan/Tilt Swing
02
sec)
~ 127
P1 P2 P3h
h=Pan/Tilt Swing
02
00h
Error
00h
Error
Ver
Ver 1111....88880000EEEE
VerVer
Run Swing
2.5.3
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
P1:00h=Pan Swing
Sequence Command
2.6
Run Group
2.6.1
Send
Return
P1:
00h ~ 05h
Run Tour
2.6.2
Send
Return
Clear Tour&Group
2.6.3
Send
Return
P1:00h=Clear the data for Tour
P2: When P1 is00h;00h=Tour number F1h=Clear all Tour
When P1 is01h;00h~05h=Group number F1h=Clear all Group
00h 1
" " " " "
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 21h
" " " " "
Group number
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 25h 00h 00h 00h 00h
" " " " "
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 2
" " " " "
Bh P1
h=Tilt Swing
01
Bh P1 P2
01
02
P1
h=Clear the data for Group
00h 00h 00h
h=Pan/Tilt Swing
00h 00h 00h
Error
Error
Error
00h 00h
Error

PTZ Trace
2.7
Set PTZ Trace
2.7.1
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
P1:00h=Memory start
P2: Pattern No.(0~3)
Stop PTZ Trace
2.7.2
Send
Return
It can be stopped by the command'Enter'.
*
Set Pan/Tilt Position Move1(Relative Movement)
2.8
Send
Return
P1:00h=Pan
P2:00h=Right(or Down)
P3P4: Relative Movement Value(Resolution:
->
00h 71h
" " " " "
h=RePlay start
01
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 73h 00h 00h 00h 00h
" " " " "
Cmd1 Cmd2 Data1 Data2 Data3 Data4
00h 3
" " " " "
h=Tilt
01
P3:High Byte, P4:Low Byte
Bh P1 P2 P3 P4
h=Left(or Up)
01
P1 P2
h=Delete
02
0.1
deg)
00h 00h
Error
Error
Error
Ver
Ver 1111....88880000EEEE
VerVer
In case of tilting camera's direction, it is flipped.
When upward, the angle will decrease.
(1)
When downward, the angle is going to increase.
(2)

Set Pan/Tilt Position Move2(Relative Movement)
2.9
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
P1:00h=Pan
P2:00h=Right(or Down)
P3P4: Relative Movement Value(Pulse)
->
In case of tilting camera's direction, it is flipped.
When upward, the angle will decrease.
(1)
When downward, the angle is going to increase.
(2)
Note!
Camera Position Range per Model
-
-
-
-
-
00h 3
" " " " "
h=Tilt
01
P3:Low Byte, P4:High Byte
SPD-2300/3000/3300:
Pan Range:0~64000, Tilt Range:794~34556
SPD-1000:
Pan Range:0~16851, Tilt Range:0~7662
SPD-3700/3750/3350, SCP-2370/2330/2270/3370:
Pan Range:0~44799, Tilt Range:0~23672
SCP-2120/3120:
Pan Range:0~38399, Tilt Range:0~16887
SCU-2370/VAC/9051
Pan Range:0~17999(0
Tilt Range:0~2000(0
Dh P1 P2 P3 P4
h=Left(or Up)
01
°~360°) =>
°~40°), 61286~65535(-85°~-0°) =>
Position*50
Error
Position*50
Ver
Ver 1111....88880000EEEE
VerVer

Ver
Ver 1111....88880000EEEE
VerVer
2.10
Special Command
The following special commands are developed in response to SI industrial requests.
STX Dome ID Host ID Cmd1 Cmd2 Data ETX CS
xA0 ID ID
0
2.10.1
P1P2: Pan Position(Pulse)->P1:High Byte, P2:Low Byte
P3P4: Tilt Position(Pulse)->P3:High Byte, P4:Low Byte
Call PT Position
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
Note!
Camera Position Range per Model
SPD-2300/3000/3300:
-
Pan Range:0~64000, Tilt Range:794~34556
SPD-1000:
-
Pan Range:0~16851, Tilt Range:0~7662
SPD-3700/3750/3350, SCP-2370/2330/2270/3370:
-
Pan Range:0~44799, Tilt Range:0~23672
SCP-2120/3120:
-
Pan Range:0~38399, Tilt Range:0~16887
SCU-2370/VAC/9051
-
Pan Range:0~17999(0
Tilt Range:0~2000(0
" "
E0
01h 00h 00h 00h 00h
°~360°) =>
°~40°), 61286~65535(-85°~-0°) =>
Command Data1~Data4
P1 P2 P3 P4
Position*50
Position*50
xAF Check Sum
0
2.10.2
P1P2: Zoom Position(Pulse)->P1:High Byte, P2:Low Byte
Only for models later than SPD-3750/3350/3700/3310/2700 Ver1.08,
P3:*Digital Zoom
Digital Zoom Ratio*10
In case of the SCP-3120, please refer to Appendix
For older models and versions
P3P4:*Digital Zoom
Call Zoom Position
Send E0h
Return
ex)P3:E7h
P3:7Fh
→
→
Cmd1 Cmd2 Data1 Data2 Data3 Data4
02h 00h 00h 00h 00h
" "
: = 256*10/(
x)
11(1.1
x)
20(2.0
0~3
bit Flip:4bit
P1 P2 P3 P4
P3+1)
3.1.

Ver
Ver 1111....88880000EEEE
VerVer
2.10.3
Call Focus Position
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
" "
03h 00h 00h 00h 00h
P1 P2
" "
P1P2: Focus Position(Pulse)->P1:High Byte, P2:Low Byte
The Focus value may vary depending on the calibration of lens VCLs.
2.10.4
Move Pan&Tilt Position(Absolute Movement)
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
04h
" " " " " "
P1 P2 P3 P4
P1P2: Pan Position(Pulse)->P1:High Byte, P2:Low Byte
P3P4: Tilt Position(Pulse)->P3:High Byte, P4:Low Byte
2.10.5
Move Pan Position(Absolute Movement
)
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
05h
" " " " "
P1 P2
00h 00h
P1P2: Pan Position(Pulse)->P1:High Byte, P2:Low Byte
Error
2.10.6
Move Tilt Position(Absolute Movement)
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
" " " " "
06h 00h 00h
P1P2: Tilt Position(Pulse)->P1:High Byte, P2:Low Byte
P1 P2
Error

Ver
Ver 1111....88880000EEEE
VerVer
2.10.7
Move Zoom Position(Absolute Movement
)
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
07h
" " " " "
P1 P2 P3
00h
Error
P1P2: Zoom Position->P1:High Byte, P2:Low Byte
P3: Digital Zoom Position
Ratio_X)-1
=(256/
ex) Digital Zoom Ratio:1.1x→P3: E7h
Digital Zoom Ratio:2.0x→P3:7Fh
Only models later than SPD-3750/3350/3700/3310/2700 Ver1.08 support Digital Zoom Position.
In case of the SCP-3120, please refer to Appendix
3.1.
Note!
Camera Zoom Range per Model
SPD-2300:0~1755
-
SPD-3000/3300:
-
SPD-1000:0~1174
-
SPD-3700/3750, SCP-2370/3370
-
SPD-3350, SCP-2330
-
SPD-2700, SCP-2270
-
SCP-2120:0~921
-
SCP-3120:32772~35952
-
SCU-2370:0~1613
-
0~1770
: 0~1613
: 0~1608
:0~1589
2.10.8
Move Focus Position(Absolute Movement
)
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
08h
"
P1 P2
00h 00h
P1P2: Focus Position->P1:High Byte, P2:Low Byte
The Focus value may vary depending on the calibration of lens VCLs.
2.10.9
One Shot AF
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
2.10.10
Target Lock On
"
15h 00h 00h 00h 00h
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send E0h
Return
"
23h 00h 00h 00h 00h
Error
Error
Error

Ver
Ver 1111....88880000EEEE
VerVer
2.11
Special Command
2.11.1
Special Command2is the protocol for the Auto Track's function.(In case of not having the
function of the Auto Track, this protocol is only for the absolute position.)
*
Move PTZ Position and Track On/Off(Abs. position move)
Note!
The command can be executable after firmware versions as follows.
Model SPD-37XX, SPU-37XX SCP-2370TH/3370TH
Dome Version v1.20 v1.00_110130
Track Version v.1.12 v1.00_110316
In case of using the related function with an old version instead of new
one, please check the version before the installation in order for avoiding
Send(14 Bytes)
1 2 3 4 5 6 7
STX Dome ID CMD Data Size P1 P2
xA1 Dome ID
0
8 9 10 11 12 13 14
P4 P5 P6 P7 P8 P9
Tilt High Tilt Low Tilt Speed Zoom High Zoom Low Action check sum
2
24h 09h
P3
Pan High Pan Low Pan Speed
C/S
P1P2:Pan Absolute Position(Pulse)
P3: Pan Speed(00h~40h)
P4P5:Tilt Absolute Position(Pulse)
P6: Tilt Speed(00h~40h)
P7P8:Zoom Position
P9:01h=Track On,00h=Track Off
Return(11 Bytes)
*
Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8 Byte9 Byte10 Byte11
A0h Host ID Cam ID E0h
P1: Action(00h:No Track,07h:Track On)
24h
P1
00h 00h 40h
AFh Checksum

Ver
Ver 1111....88880000EEEE
VerVer
2.11.2
Call PTZ Position(SCP-2370/2330/2270/3370 model only.)
1 2 3 4 5
STX Dome ID CMD Data Size C/s
xA1 Dome ID 26h
0
Return(14 Bytes)
*
0h
Checksum
Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7
STX Dome ID CMD Data Size P1 P2
A1h
Host ID
26h 07h
Pan High Pan Low Tilt High
Byte8 Byte9 Byte10 Byte11 Byte12
P4 P5 P6 P7 C/S
Tilt Low Zoom High Zoom Low Digital Zoom Checksum
P1P2:Pan Absolute Position(Pulse)
P3P4:Tilt Absolute Position(Pulse)
P5P6:Zoom Position
P7: Digital Zoom Position
Ratio_X)-1
=(256/
ex) Digital Zoom Ratio:1.1x→P3: E7h
Digital Zoom Ratio:2.0x→P3:7Fh
P3
Checksum: The value of Modulo
processed by'Logical Not(~)'
Checksum
= ~((
Byte
Note!
Camera Position Range per Model
SPD-2300/3000/3300:
-
Pan Range:0~64000, Tilt Range:794~34556
SPD-1000:
-
Pan Range:0~16851, Tilt Range:0~7662
SPD-3700/3750/3350, SCP-2370/2330/2270/3370:
-
Pan Range:0~44799, Tilt Range:0~23672
SCP-2120/3120:
-
Pan Range:0~38399, Tilt Range:0~16887
SCU-2370/VAC/9051
-
Pan Range:0~17999(0
Tilt Range:0~2000(0
°~40°), 61286~65535(-85°~-0°) =>
equal toatotal of Byte2 to Byte
256
2 +……+
°~360°) =>
Byte
11) &
Position*50
FFh)
11
Position*50

Note!
Camera Zoom Range per Model
SPD-2300:0~1755
-
SPD-3000/3300:
-
SPD-1000:0~1174
-
SPD-3700/3750, SCP-2370/3370
-
SPD-3350, SCP-2330
-
SPD-2700, SCP-2270
-
SCP-2120:0~921
-
SCP-3120:32772~35952
-
SCU-2370:0~1613
-
0~1770
: 0~1608
:0~1589
: 0~1613
Ver
Ver 1111....88880000EEEE
VerVer
2.12
New Protocol
The following New protocol are developed in response to SI industrial requests.
2.12.1
Set Home Position
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
h=HP Specified
00
h=ON/OFF Specified
01
h=Specified of Hour
02
2.12.2
Set Home Position Status
00h 0
" " " " "
P1 P2
Bh P1 P2
h~FEh=Preset Number
00
h=OFF
00
h=5Sec
00
h=30Sec
03
h=3Min
06
h=5Min(Initial Value=03h)
08
/ 01
/ 01
/ 07
h=ON
h=10Sec
/ 04
h=4Min
h=1Min
00h
/ 02
/ 05
h=20Sec
h=2Min
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
00h 8
" "
Bh P1
P1 P2
00h
00h 00h
"
00h
Error
Error
h=HP Specified
00
h=ON/OFF Specified
01
h=Specified of Hour
02
P1 P2
h~FEh=Preset Number
00
FFh=No Registration
h=OFF
00
h=5Sec
00
h=30Sec
03
h=3Min
06
h=5Min(Initial Value=03h)
08
/ 01
/ 01
/ 04
/ 07
h=ON
h=10Sec
h=1Min
h=4Min
/ 02
/ 05
h=20Sec
h=2Min

Ver
Ver 1111....88880000EEEE
VerVer
2.12.3
Freeze
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
P1:00h=OFF
2.12.4
OSD Setting
00h 5
" " " " "
h=ON
/ 01
Dh
02h
P1
00h 00h
Cmd1 Cmd2 Data1 Data2 Data3 Data4
Send
Return
00h
" " " " "
P1:00h=Camera ID
h=Preset Name
03
h=PTZ Position
06
P2:00h=ON
2.12.5
Text Display Command
B5h P1 P2
h=Camera Name02h=Preset Number
01
h=Sequence Status
04
h=ON
01
h=Area Name
05
00h 00h
Please contact us for more usage.
1 2 3 4 5 N
STX Dome ID CMD Data Size Data
xA1 Dome ID
0
20h
P1 P2
…
…
P1P2: Zoom Position->P1:High Byte, P2:Low Byte
Error
Error
C/S
Checksum

Protocol Samples
3.
The following commands are examples of protocols with the camera ID set to01h.
Command Protocol Note
OSD ON A0
One shot AF A0
Call Zoom Pos. A0
Call Pan Pos. A0
Set Preset
Call Preset
Zoom Tele A0
Zoom Stop A0
Pan Right A0
3
3
A0
A0
01 00 00
01 00
01 00
01 00
01 00 00 03 02 00 00 00
01 00 00 07 02 00 00 00
01 00 00 20 00 00 07 00
01 00 00 00 00 00 00 00
01 00 00 02 22 00 00 00
B1
00 00 00 00
E0
15 00 00 00 00
E0
02 00 00 00 00
E0
01 00 00 00 00
AF
4D
AF
09
AF
1C
AF
1D
AF F9
AF F5
AF D7
AF FE
AF DA Speed
Menu ON
34
Ver
Ver 1111....88880000EEEE
VerVer

Appendix
3.
SCP-3120 Digital Zoom Parameter
3.1.
Digital Zoom Position Parameter
1.08 0
1.17 0
x0a
x15
Ver
Ver 1111....88880000EEEE
VerVer
1.25 0
1.33 0
1.42 0
1.5 0
1.58 0
1.67 0
1.83 0
1.92 0
2 0
2.17 0
2.42 0
2.58 0
2.83 0
3 0
3.5 0
4 0
5 0
6 0
x20
x2a
x35
x40
x4a
x55
x6a
x75
x80
x87
x91
x99
xa3
xab
xb5
xc0
xcd
xd6
7 0
8 0
9 0
10 0
11 0
12 0
13 0
14 0
15 0
16 0
xdc
xe0
xe4
xe7
xe9
xeb
xed
xee
xef
xf0