Printed in Korea
Code No. : GH68-01359A
English. 2000/07. Rev.1.0
Table of ContentsFCC RF EXPOSURE INFORMATION
In August 1996 the Federal Communications Commission (FCC) of
the United States with its action in Report and Order FCC 96-326
adopted an updated safety standard for human exposure to radio
frequency electromagnetic energy emitted by FCC regulated
transmitters. Those guidelines are consistent with the safety
standard previously set by both U.S. and international standards
bodies. The design of this phone complies with the FCC guidelines
and these international standards.
Use only the supplied or an approved antenna. Unauthorized
antennas, modifications, or attachments could impair call quality,
damage the phone, or result in violation of FCC regulations.
Do not use the phone with a damaged antenna. If a damaged
antenna comes into contact with the skin, a minor burn may result.
Please contact your local dealer for replacement antenna.
Body-worn Operation
This device was tested for typical body-worn operations using the
optional belt-clip/holster placed 0.7 inches (1.8cm) from the body.
To comply with FCC RF exposure requirements, a minimum
separation distance of 0.7 inches (1.8cm) must be maintained
between the user’s body and the phone, including the antenna,
whether extended or retracted. The use of third-party belt-clips/
holsters with no metallic components that provide the minimum
separation distance of 0.7 inches (1.8cm) can be used to satisfy
FCC RF exposure requirements. The use of non-tested accessories
or other body-worn operations may not comply with FCC RF
exposure requirements and should be avoided. Contact your local
dealer for optional accessory items.
Vehicle Mounted External Antenna (optional, if
available.)
A minimum separation distance of 7.9 inches (20cm) must be
maintained between a person and the vehicle mounted external
antenna to satisfy FCC RF exposure requirements.
For more information about RF exposure, please visit the FCC web
site at www.fcc.gov
Read these simple guidelines. Failure to comply with
these guidelines may be dangerous or illegal.
For more detailed safety information, see Safety
Information on page 77.
ROAD SAFETY COMES FIRST
Do not use a hand-held phone while driving; park the
vehicle first.
SWITCH OFF IN AIRCRAFT
Mobile phones can cause interference. Using them on
aircraft is illegal.
SWITCH OFF NEAR BLASTING
Do not use the phone where a blasting operation is in
progress. Observe restrictions, and follow any
regulations or rules in force.
SWITCH OFF WHEN REFUELLING
Do not use the phone at a refuelling point or near fuels
or chemicals.
INTERFERENCE
All mobile phone may be subject to radio interference,
which may affect their performance.
45
QUALIFIED SERVICE
Only qualified service personnel must install or repair
cellular equipment. Use only approved accessories and
batteries.
Getting Started
Unpacking
Your package contains the following items.
USE SENSIBLY
Use only in the normal position (to ear).
Avoid unnecessary contact with the antenna when the
phone is switched on.
IMPORTANT!Use only accessories approved by the
phone manufacturer. This apparatus is intended for use
when supplied with power from SAMSUNG approved
Travel charger. The use of any other types will invalidate
any approval or warranty applying to the phone, and
may be dangerous.
When you disconnect the power cord of any accessory,
grasp and pull the plug, not the cord.
Handset
Travel Charger
In addition, you can obtain the accessories for your
phone from your local SAMSUNG dealer. For information
on the accessories, see page 74.
Standard Battery
User’s Manual
Necklace
67
Getting Started
Phone Layout
Getting Started
The following illustrations show the main elements of
your phone.
Antenna
Service light
Earphone jack
Volumn key
Menu key
Send key
Earpiece
Display
O K / N av i g a t i o n
Key
CLR key
End/Power key
Vibrator key
Microphone
Key Functions
Enters the menu facility. Also, scrolls
through the menu options.
Performs several useful functions:
-In Standby mode, slide it up to find your
Phone Book entry by location number.
-In Standby mode, slide it down to view your
Phone Book (in alphabetical ord e r ) .
-In Standby mode, slide it left to launch the
PIM Schedulor.
- F rom Standby or Conversation mode, slide it
right to access the Messages Menu, slide
and hold it to listen to your voice mail.
-In Standby mode, press it to launch the We b
B ro w s e r.
-When navigating a menu, press it to select
the highlighted item.
Deletes characters from the display.
In the menu facility, returns to the previous
menu level.
Makes or answers a call.
In Standby mode, enters the Outgoing Call
Log.
Flip cover
Ends a call. Also switches the phone on and
off when pressed and held.
In the menu facility, returns to the idle mode
and cancels your input.
8
9
Getting Started
Key Functions (continued...)
Enters numbers, letters and some special
characters.
In Standby mode, if you hold down the # key,
the alert type quickly switches to the vibrate
mode (see page 28).
Display
Display Layout
Getting Started
Icons
Signal strength: Shows the received
signal strength. The greater the number of
bars, the better the signal strength.
Service: Appears when a call is in
progress.
No service indicator: Appears when you
are outside a service area. When it
appears, you cannot make or receive calls.
Wait a little while for a signal or move into
an open area.
Roaming: Appears When you are out of
your home area and have registered with a
different network (when travelling in other
countries, for example).
The display comprises two areas; an upper line of fixed
icons, and the lower text and graphic area. The
following icons display at power-on:
Icons
Text and
graphic area
10
New Message: Appears when a new
message has been received.
Digital mode: Indicates that the phone
is in a Digital mode.
Vibrator on: Appears when vibrate mode is
on. An incoming call will vibrate the phone
rather than ring it.
Battery strength: Shows the level of your
battery. The more bars you see, the more
power you have left.
11
Getting Started
Backlight
The display is illuminated by a backlight. When you
press any key, the backlight illuminates. It turns off if no
key is pressed within a given period of time, depending
on the Backlight option set in the Display menu. The
backlight remains on at all times when the phone is
connected to a car kit (optional).
To specify the length of time for which the backlight is
active, set the Backlight menu option (4-1); see page
47 for further details.
Getting Started
Installing Battery
To Install the Battery
1. Align the tabs at the bottom of the battery with the
c o rresponding slots in the phone.
2. Push the battery down towards the catch until it clicks
in place.
To Remove the Battery
1. Tu rn the power off .
2. Pull the catch on the back of the phone and lift the
b a t t e ry away.
12
13
Getting Started
Charging a Battery
Getting Started
Your phone is powered by a rechargeable Li-ion battery.
A travel charger is provided with your phone. Use only
approved batteries and chargers. Ask your local
SAMSUNG dealer for further details.
The phone can be used while the battery is charg i n g .
N o t e : You must fully charge the battery before using your
phone for the first time.
1. Connect the lead from the travel charger to the bottom
of the phone. Check that the arrow on the lead
connector is facing towards the front of the phone.
2. Connect the charger to a standard AC wall outlet.
The color indication of the lamps on the charger is as
f o l l o w s :
Red: charg i n g
G reen: fully charg e d
3. When charging is finished, disconnect the charger fro m
the power outlet.
Disconnect the adapter from the phone by pressing the
g rey tabs on either side of the connector and pulling
the connector out.
Low Battery Indicator
When the battery is weak and only a few minutes of
talk time remain, an empty battery icon (no bars
displayed) flashes in the upper right corner of the
screen. You will hear a warning tone.
Battery is running
[MON]
06/2620:06
When the battery becomes too weak for the phone to
operate, it switches off automatically.
out of power.
14
15
Getting Started
Switching the Phone On/Off
1. Open the phone.
2. Hold down the key for more than one second to
switch the phone on.
The red light flashes, and an alert sounds:
• When the system locates services, the greeting
message displays along with the date and time.
You can now place and receive calls.
• If the system cannot locate service, the greeting
message displays without the date and time. In this
case, you cannot place and receive calls. You can
try later when service is available.
• If your phone is locked, the lock icon appears. Press
the key, and enter the four-digit lock code to
unlock the phone.
3. When you wish to switch the phone off, hold down
the key for more than two seconds.
Getting Started
Standby Mode
Standby is the most basic state of your phone. The
phone goes into Standby mode soon after you turn it on,
or whenever you briefly press the key. When your
phone is in Standby mode, you will typically see the
greeting message and current date and time. If you
enter a phone number, you can press the key to
dial it, or press the key to save it in the internal
phone book.
Press the key at any time to return to Standby
mode. Be careful; if you are on a call when you press
the key, you will return to Standby mode, but your
call will be disconnected. Press the key several
times or hold it down to return to Standby mode without
ending the call.
WA R N I N G :Do not switch on the phone when wire l e s s
phone use is prohibited or when it may
cause interf e rence or danger.
Note: Your phone has a built-in antenna. As with any
other radio-transmitting device, do not touch the
antenna unnecessarily when the phone is
switched on. Contact with the antenna aff e c t s
call quality and may cause the phone to operate
at a higher power level than otherwise needed.
16
17
Call Functions
Making a Call
In Standby mode, key in the area code and phone
number and press thekey.
Call Functions
Emergency Dialing
You can place calls to emergency numbers in your
emergency number list even if your phone is locked or
all outgoing calls are restricted. For further information
on emergency numbers, refer to page 68.
N o t e: If you have set Auto Retryoption (6 - 1) to O n ( s e e
page 55), and the call does not connect, the
phone automatically retries to make the call.
Correcting the Number
To clear ...Then ....
The last digit displayedPress the key .
The whole display Hold down thekey
for more than one
second.
Ending a Call
When you have finished your call, briefly press the
key or close the phone.
Prepend Dialing
The Prepend option lets you add digits such as area
codes and network feature activation codes to a phone
number that is in your Internal Phone Book or Call Logs.
(The prepended phone number cannot be more than 10
digits.)
To prepend existing phone numbers in the Phone Book or
Call Logs:
1. Access the phone number entry.
2. When the desired phone number displays, press the
key to access the Optionsmenu.
3. Press thekey (or key in Call Logs) to
select the Prepend option.
4. Enter the area code or feature code.
5. Press thekey to dial the number.
1918
Call Functions
Call Functions
Making a Call from the Phone Book
You can store the phone numbers called regularly in
memory, called the Phone Book. You then simply recall
the number to dial. For further information on Phone
Book, refer to page 37.
Speed Dialing
Once you have stored phone numbers in the phone book
memory, you can dial them easily whenever you want.
One-Touch Dial
Memory locations 01 through 09 are special one-touch
locations. You can dial the phone numbers stored in the
Phone Book memory from 01 through 09 simply by
pressing one button.
Press and hold the third digit of the memory location
containing the number to be dialed.
For example: Location no. 009
Press and hold.
The number (and name) stored is displayed, then dialed.
Two-Touch Dial
Memory locations 10 through 99 are special two-touch
locations.
Press the second digit briefly, then hold down the third
digit of the memory cell.
For example: Location no. 023
Press briefly and hold down .
The number (and name) stored is displayed, then dialed.
Three-Touch Dial
Memory locations 100 through 249 are special threetouch locations.
Press the first and the second digit briefly, then hold
down the third digit of the memory cell.
For example: Location no. 123
Press and briefly, then hold down
.
The number (and name) stored is displayed, then dialed.
Note : When several numbers are saved in one
location, only the phone number which is specified with
Set Speed Dialoption will be automatically dialed. For
details, refer to the E d i t option under Find Namem e n u
on page 38.
2120
Call Functions
Call Functions
Last Number Redial
The phone stores the last 10 numbers dialed. To recall
any of these numbers, proceed as follows.
1. If there are any characters on the display, clear the
display by holding down the key for more than
one second.
2. Press the key. The list of outgoing calls are
displayed.
3. Slide the key to scroll through the list until you
select the required name or number.
4. Press thekey to dial the number displayed.
Answering a Call
When somebody calls you, the phone rings and the
phone icon is displayed in the middle of the screen.
(( ))
nnn
If the caller can be identified, the caller’s phone number
(or name if pre-stored in your Phone Book) is displayed.
If the caller cannot be identified, only the phone icon
appears.
1. To answer a call, open the flip cover. If the flip cover
is already open, press any key except for the
key.
If the Anykey Answer menu (6-4) is set off, you can
answer a call only by pressing the key.
Caller’s name or
number
2. End the call by closing the flip cover or pressing the
key.
N o t e: You can answer a call while using the phone
book or menu features. The current operation
will be interru p t e d .
2322
Call Functions
Call Functions
Viewing Missed Calls
If you are unable to answer a call for any reason, you
can find out who was calling you, if this service is
available. In this way, you can call the person back
simply by pressing the key, if necessary.
The number of missed calls is displayed on the idle
screen immediately after the call was missed.
To view the missed call, refer to ‘Incoming’ (1-2) under
‘Calls’ on page 35.
In-Call Options
Your phone provides a number of functions that you can
use during a call. You may not utilize all of these
functions at all times. Many of the in-call options are
network services.
Press the key during a call to access the following
in-call options:
Mute/Unmute: allows you to switch your phone’s
microphone off, so that the other party cannot hear you.
Silent Key: does not transmit the key tones. It allows
you to press keys without hearing annoying key tones
during a call.
N o t e: To communicate with answering machines or
computerized telephony systems, the Silent key o p t i o n
must be disabled.
Send Tel #: sends DTMF tones of your number.
My Phone #: shows your phone number.
Send DTMF: sends DTMF tones of the currently
displayed number. DTMF (Dual Tone Multi Frequency)
tones can be used to control electronic phone services
such as bank-by-phone or voicemail. During a call, key in
the digits you want to send as DTMF tones, for example,
the bank account number and password. Then select
this in-call option.
Example: You wish to say something to another person
in the room but do not want the other party to hear you.
Calls: allows you to access the Calls menu.
Phone Book: allows you to access the Phone Book
menu.
2524
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.