Samsung S-1 URX-P01 User guide

Intruder Detector using a radar principle

URX-P01

User’s Manual

Written By
Device Development Group

S-1 CORPORATION

168, S1 BUILDING,

SOONHWA-DONG, JOONG-GU,

SEOUL, KOREA

Tel: [phone]

Fax: [phone]

Website: www.s1.co.kr

Revised: May 2015

CAUTION!!

• This equipment may only be operated Indoors.

• Do not use to Outdoors.

• Do not intentionally install aimed at windows or outside opening doors.

Table of Contents

Introduction & Information ………………………...............……….1

Features of the UWB Sensor....……………………………………...2

Coverage of the UWB Sensor.……………………………………….3

UWB Sensor Specifications………………………………………….4

Installation………………………………………………………………5

Operational precautions……………………………………………...7

INTRODUCTION & INFORMATION

Introduction

The UWB(Ultra Wide Band) sensors refers to a kind of radar technology that was traditionally
used in military applications. When used as a security means, it’s low power, wide band
characteristics often causes frequent false alarms. Overcoming such limitations with its
excellence in technology, S1 showcases the first ever UWB-based security sensor in the world.
Its radar-based principle makes it inherently immune to heat source-induced false alarms and
enables high level of sensitivity to the movement of heat-insulated intruders. Coverage can be
flexibly adjusted to enable its deployment in various environments.

This document describes the features and the specifications of the UWB sensor, important

regulatory information concerning its use, and details on how to diagnose potential problems.

Information to the User

The UWB sensor is an ultra-wideband(UWB) wireless device certified under FCC Part 15.517.

It’s use is subject to technical requirements for indoor UWB systems, in particular the stipulation

that the devices must only be used indoors. Users should note carefully the following
information:

• CAUTION: This equipment may only be operated indoors. Operation outdoors is in
violation of 47 U.S.C. 301 and could subject the operator to serious penalties.

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

Users should also carefully note the following information:

• CAUTION: Any changes or modifications made to the “UWB Sensor” which are not

expressly approved by the “S-1” could void the user’s authority to operate the equipment.

• NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications, However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver
Is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- 1- UWB Intrusion Detection Sensor – URX-P01

FEATURES OF THE UWB SENSOR

Features of the UWB Sensor

The diagram below shows several important features of the UWB Sensor:

UWB

Antenna

GB-41

(Bracket)

Lens

Terminal

(Power, COM,Tamper)

Rotary Switch

LED

[SET]

Magnetic Switch

Point

Label

(System)

[TOP] [BOTTOM]

- 2- UWB Intrusion Detection Sensor – URX-P01

COVERAGE OF THE UWB SENSOR

Coverage of the UWB Sensor

Maximum detection area of the sensor is as follows:

Horizontal View

Vertical View

0m

1.8m

2.4m

3.0m

0m(0ft)

Note

- Installer is to walk into the pattern or may walk perpendicular to the pattern to verify the pattern.

-3- UWB Intrusion Detection Sensor – URX-P01

2m(6.5ft)

5m(16.4ft)

10m(32.8ft)

0ft

6ft

8ft

10ft

UWB SENSOR SPECIFICATIONS

Model

URX-P01

Detection Method

Impulse Radio(Ultra Wide Band)

Colors

URX-P01-WR : White

URX-P01-BR : Black

Coverage

Wide: 8m x 10m(26.24 x 32.80ft), 80˚ Wide

Mounting Height

2.0 ~ 3.0m(6.5 ~ 10ft)

Intruder Speed

0.3 ~ 1.5m/sec.(1 ~ 5ft/sec.)

LED Alarm Indicator

Red LED ON (When detecting)

Tamper Parameters

N.C (200VDC 0.1A max.)
Alarm Output Period

2 Sec.

Alarm Output

N.C (60VDC 0.6A max)

Warm-up Period

Approx. Under 10 sec.

Power Supply

12VDC(9.6 ~ 14.4VDC)
Current Consumption

20mA (max.) at 12VDC(9.6 ~ 14.4VDC)

Weight

85g(2.99oz)

Operating Temperature

-10℃ ~ +50℃(+14℉ ~ +122℉)

Operating Humidity

95% max.

UWB Sensor Specifications

The specification of the sensor refer to the following table:

- 4- UWB Intrusion Detection Sensor – URX-P01

INSTALLATION

1 Step : Using key separate “TOP” and “BOTTOM”

2 Step : Assemble “Bottom” and “GB-41”

3 Step : Connection “Top” and “Wire”

SPARE
TAMPER ALRAM 12VDC

NC C SP NC C (-) (+)

- 5- UWB Intrusion Detection Sensor – URX-P01

INSTALLATION

Switch

Direction

0 1 2 3 4 5 6 7 8

9

Range

10m

1m

2m

3m

4m

5m

6m

7m

8m

9m

4 Step : Assemble “Top” and “Bottom”

※Adjustable detection range from 1 to 10 meter by rotary switch

☞ Note that each adjusted range has ±0.5m deviation

Be sure walk test after installation

Note

1. The unit is to be tested at a min once per year.

2. This unit is designed to detect a burglar or an intruder. When an alarm control panel is activated, the
unit detects a burglar or an intruder. It is only a part of a complete system, we cannot responsibility any
damage to change without prior consent of the S-1

※Specifications and design are subject to change without prior notice

- 6- UWB Intrusion Detection Sensor – URX-P01

OPERATIONAL PRECAUTIONS

Operational precautions

• Do not apply voltages higher than the

rated voltage.

AC220V

• When swaying objects(mobiles of metal material),

in the detection area, change the direction or

adjust the detection distance.

• Do not install where dogs and cats.

• Do not install the outdoor.

• Do not install in the swaying wall.

• Do not install the curtain(blind) by the external

wind swaying.

• Do not install near any moving fan.

- 7- UWB Intrusion Detection Sensor – URX-P01