Samsung RL19PSUSQ User Manual

SyncMaster 720B/720T/920T

Power

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z

This may cause fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

z

The monitor may cause injury by falling.

Set down the monitor carefully.

z The monitor could be damaged or broken.

Do not place the monitor face down.

z The TFT-LCD surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

z Installation by unqualified personnel may result in injury. z Always use the mounting device specified in the owner's manual.

Leave a space for ventilation between the product and the wall.

z Poor ventilation may cause the interior temperature to rise and lead to

fire.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

z A dirty connector may cause an electric shock or fire.

Others

Contact the Service Center or Customer Center for interior cleaning once a year.

z

Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.

Do not remove cover (or back).

z This may cause an electric shock or fire.

z

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service.

z This may cause an electric shock or fire.

Be careful not to let water drip into the monitor or expose the monitor to moisture.

z This may cause malfunction, an electric shock or fire. z Especially avoid operating the monitor near water or outdoors where it

could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord.

z

The monitor may malfunction, causing an electric shock or fire.

z Then contact the Service Center .

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

z

Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

z This may cause a breakdown, electric shock or fire due to damage to

the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

z

This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

z This may cause malfunction, an electric shock or fire. z If a foreign substance enters the monitor, unplug the power cord and

contact the Service Center .

Do not use or store inflammable substances near the monitor.

z

This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z

This may cause an electric shock, fire or injury.

Do not insert metal objects such as utensils, wire or drill bits or things that catch fire easily, such as pieces of paper or matches, into the vents, the headphone or A/V ports on the monitor.

z

This may cause malfunction, an electric shock or fire.

z

Always contact the Service Center if foreign substances/objects enter into the monitor.

If you view a fixed screen for an extended period of time, residual image or blurriness may appear.

z

Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.

Be careful when adjusting the stand angle.

z Applying too much force may cause the monitor topple over or fall,

resulting in injury.

z

Your hand or finger(s) may get caught between the monitor and the

stand, causing injury.

Adjust the resolution and frequency to the levels appropriate for the model.

z Inappropriate resolution may cause undesirable picture quality.

15 inch - 1024 X 768 17,19 inch - 1280 X 1024

Be careful that adapter should not be in contact with water and therefore not be wet.

z

This may cause malfunction, an electric shock or fire.

z

Do not use adapter by the waterside or outside particularly when it rains or snows.

z Be careful that adapter should not be wet while cleaning floor with

water.

Keep all power adapters apart.

z

Failure to do so may cause fire.

Keep power adapter away from any other heat source.

z Failure to do so may cause fire.

Remove and discard vinyl bag from power adapter before use.

z

Failure to do so may cause fire.

Always keep power adapter in well-ventilated area.

Keep the volume at a proper level when you use the headphones.

z Excessively loud volume levels may damage hearing.

Keep a proper distance between your eyes and the monitor screen.

z

Sitting too close to the monitor on a continuous basis may damage

eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor

.

Do not use the monitor where it may be exposed to strong vibrations.

z

Exposure to strong vibrations may cause fire and hazard and shorten the life of the monitor.

When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.

z

Failure to disconnect the cable may damage it and lead to fire or an electric shock.

y

®

r

SyncMaster 720B

Unpacking

Monitor

Manual

Please make sure the following items are included with your monitor.

Quick Setup Guide

items are missing, contact your dealer.

If an

Warrant y Ca rd

(Not available in all

locations)

User's Guide,

Monitor Driver, Natural Color software, MagicTune™ software,

Pivot

Pro software

Cable

Power Cord DC Adapte

For Multimedia model (Option)

Multimedia model Audio Cable

Front

Menu button [ ]

MagicBright button []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright control buttons.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu.

Brightness button [ ]

Adjust buttons [ ]

: Normal Brightness

2) Text

For documentations or works involving heavy text.

3) Internet

: Medium Brightness

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a Game.

5) Sport

For watching motion pictures such as a Sport.

6) Movie

: High Brightness

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

When OSD is not on the screen, Push the button to adjust brightness.

Adjust items in the menu.

Enter button [ ]

Auto button Power button

Power indicator

Activates a highlighted menu item. Use this button for auto adjustment. Use this button for turn the monitor on and off. This light glows green during normal operation, and blinks green

once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

PC Connection Terminal

Computer Connection Terminal (15 Pin D-SUB)

How to disconnect a cable

DC Power Connection Terminal (DC 14V)

This product may be used with 90 ~ 264VAC. (Voltage is automatically adjusted by the power adapter.)

Audio Connection Terminal (Multimedia Model / Option)

Audio Connection Terminal

See Connecting the Monitor for further information regarding cable connections.

y

®

r

SyncMaster 720T/920T

Unpacking

Monitor

Manual

Please make sure the following items are included with your monitor.

Quick Setup Guide

items are missing, contact your dealer.

If an

Warrant y Ca rd

(Not available in all

locations)

User's Guide,

Monitor Driver, Natural Color software, MagicTune™ software,

Pivot

Pro software

Cable

Power Cord DC Adapte

For Multimedia model (Option)

Multimedia model Audio Cable

Front

Menu button [ ]

MagicBright button []

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright control buttons.

1) Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu.

Brightness button [ ]

Adjust buttons [ ]

: Normal Brightness

2) Text

For documentations or works involving heavy text.

3) Internet

: Medium Brightness

For working with a mixture of images such as text and graphics.

4) Game

For watching motion pictures such as a Game.

5) Sport

For watching motion pictures such as a Sport.

6) Movie

: High Brightness

For watching motion pictures such as a DVD or Video CD.

>>Click here to see an animation clip

When OSD is not on the screen, Push the button to adjust brightness.

Adjust items in the menu.

Enter button [ ] / Source button

Activates a highlighted menu item. / Push the 'Source', then Selects the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the Digital mode, you must connect your monitor to the graphic card's port using the DVI cable.

Auto button Power button

Power indicator

Use this button for auto adjustment. Use this button for turn the monitor on and off. This light glows green during normal operation, and blinks green

once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

PC Connection Terminal

How to disconnect cables

DC Power Connection Terminal (DC 14V)

Computer Connection Terminal (15 Pin D-SUB) Computer Connection Terminal (DVI)

This product may be used with 90 ~ 264VAC. (Voltage is automatically adjusted by the power adapter.)

Audio Connection Terminal (Multimedia Model / Option)

Audio Connection Terminal

See Connecting the Monitor for further information regarding cable connections.

SyncMaster 720B

Connect the power cord for your monitor to the power port on the back of the monitor.

1.

Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analog) connector on the video card.

2-1.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

Connected to a Macintosh.

2-2.

Connect the monitor to the Macintosh computer using the D-SUB connection cable. In the case of an old model Macintosh, you need to connect the monitor using a special Mac

2-3.

adapter. Connect the audio cable for your monitor to the audio port on the back of your computer.

3.

Turn on your computer and monitor. If your monitor displays an image, installation is

4.

complete.

Pivot Stand

Pivot Pro Installation

(

)

(

)

(

)

Caution :

When Pivoting the monitor, the corner of the monitor may reach to the floor. Tilt the monitor backward more than 45 degrees and then Pivot it. Failure to do so may damage the monitor.

Installing a VESA base

Sold separately

1. Bracket

Set-Mount

3. Anchors (3EA)

2. Bracket

Wall-Mount

4. Screws (3EA) Wall-Mount

5. Screws (4EA)

(Contact a local Samsung Electronics service center to buy optional items.)

1. VESA Mounting Bracket

2. Attaching a base

(2)

(1)

Fold the monitor stand. Turn it so that the side to which the cable is connected faces down. Attach the

(1)

VESA Mounting Bracket to the bottom side of the stand. Align the holes of the bracket with those in the VESA stand, and fasten it tightly in place with four screws.

This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad.

NOTE:

3. Wall Mounting the Monitor

(2)

Caution:

The stand is made of aluminum. Keep it from getting nicked or scratched.

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web site : http://www.samsung-monitor.com/ (Worldwide)

http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea ) http://www.samsungmonitor.com.cn/ (China)

Windows ME

1. Insert CD into the CD-ROM drive.

2. Click

"Windows ME Driver"

.

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. Click the

"Install"

button in the

"Warning"

window.

5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive.

2. Click

"Windows XP/2000 Driver"

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. If you can see following message window, then click the Then click

"OK"

button.

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung

"Continue Anyway"

button.

Monitor homepage.

http://www.samsung-monitor.com/.

5. Monitor driver installation is completed.

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z

Internet web site : http://www.samsung-monitor.com/ (Worldwide)

http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea ) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

3. Click "

" —> "

Start

Display

Control Panel

" then click the "

" icon and choose the "

Appearance and Themes

Settings

" tab then click "

Advanced..

".

" icon.

4. Click the "

Properties

" button on the "

Monitor

" tab and select "

Driver

" tab.

5. Click "

6. Select "

Update Driver..

" and select "

Don't search ,I will..

Install from a list or..

" then click "

" and then click "

Have disk

".

7. Click the "

Browse

model list and click the "

" button then choose A:(D:\Driver) and choose your monitor model in the

" button.

Continue Anyway

" button. Then

This monitor driver is under certified MS logo and this installation doesn't

K

damage your system. The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung-monitor.com/.

9. Click the "

" button, then click "OK" button continually.

Close

10. Monitor driver installation is completed.

Microsoft® Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "

2. Click the "

Browse

" button on the "

Insert disk

3. Choose A:(D:\Driver) then click the "Open" button and then click "

" window.

File Needed

" window.

" button.

O

How to install

1. Click "

2. Double click the "

3. Choose the "

4. Choose "

Start

Monitor

" , "

Setting

Settings

" , "

Control Panel

" Icon.

Display

" tab and then click "

".

Advanced..

".

Case1:If the "Properties" button is inactive, it means your monitor is properly configured.

Please stop installation

Case2:If the "Properties" button is active, click the "Properties" button then follow next steps

continually.

5. Click "

6. Choose "

specific driver

7. Click the "

8. Click the "

9. Choose your monitor model and click the "

10. Click the "

" and then click on "

Driver

Update Driver..

" then click on the "Next" button.

Display a list of the known drivers for this device so that I can choose a

" then click "

Browse Open

Finish

" button then choose A:(D:\Driver).

" button, then click "OK" button.

" button then the "

" and then click "

Have disk

" button then click "

".

If you can see the " And click the "

Finish

Digital Signature Not Found

" button then the "

Close

" window then click the "

" button.

Microsoft® Windows® Millennium Operating System

Yes

"button.

1. Click "

2. Double click "

3. Select the "

4. Select the "

5. Click the "

6. Choose "

7. Choose "

8. Click the "

" , "

Start

Display Settings Monitor

Change

Specify the location of the driver

" , "

Setting

" icon.

" tab and click "

" tab.

" button in the "

Control Panel

Advanced Properties

Monitor Type

".

" area.

".

Display a list of all the driver in a specific location..

Have Disk

" button

" button.

" then click "

9. Specify A:\(D:\driver) then click "OK" button.

10. Select "

Show all devices

" and choose the monitor that corresponds to the one you

connected to your computer and click "OK".

11. Continue choos ing "

" button and "OK" button until you close the Display Properties

Close

dialogue box.

Microsoft® Windows® NT Operating System

1. Click

Start,Settings,Control Panel

2. In Display Registration Information window, click Settings Tab and then click .

Modes

, and then double-click

Display

icon.

All Display

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)

and then click OK.

4. Click

button if you see the screen working normally after clicking

Apply

. If the screen is

Test

not normal, change to a different mode (lower mode of resolution, colors or frequency).

If there is no Mode at

All Display Modes

, select the level of resolution and vertical

frequency by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. T he third sc reen is for

setting your mouse

.

3. Set a mouse for your computer.

4. The next screen is for

selecting a keyboard

.

5. Set a Keyboard for your computer.

6. The next screen is for

7. First of all, set a

horizontal frequency

setting your monitor

.

for your monitor. (You can enter the frequency

directly.)

8. Set a

vertical frequency

9. Enter the

model name of your monitor

for your monitor. (You can enter the frequency directly.)

. This information will not affect the actual execution

of X-Window.

10. You have

Execute

finished

X-Window after setting other requested hardware.

setting up your monitor.

Natural Color

Natural Color Software Program

One of the recent problems in using a computer is that the color of the images printed out by a

[

]

printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program.

How to install the Natural Color software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CDROM Drive, click the Enter D:\color\eng\setup.exe and then press the

button of Windows and then select

[Start]

<Enter>

key.

[Execute]

.

(If the drive where the CD is inserted is not D:\, enter the applicable drive.)

How to delete the Natural Color software program

Select

[Setting]/[Control Panel]

program]

.

Select Natural Color from the list and then click the

on the

menu and then double-click

[Start]

Add/Delete

[Add/Delete a

button.

SyncMaster 720T/920T

Connect the power cord for your monitor to the power port on the back of the monitor.

1.

Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analog) connector on the video card.

2-1.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

Using the DVI (Digital) connector on the video card.

2-2.

Connect the DVI Cable to the DVI Port on the back of your Monitor.

Connected to a Macintosh.

2-3.

Connect the monitor to the Macintosh computer using the D-SUB connection cable. In the case of an old model Macintosh, you need to connect the monitor using a special Mac

2-4.

adapter. Connect the audio cable for your monitor to the audio port on the back of your computer.

3.

Turn on your computer and monitor. If your monitor displays an image, installation is

4.

complete.

Pivot Stand

(

)

(

)

(

)

Pivot Pro Installation

Caution :

When Pivoting the monitor, the corner of the monitor may reach to the floor. Tilt the monitor backward more than 45 degrees and then Pivot it. Failure to do so may damage the monitor.

Installing a VESA base

Sold separately

1. Bracket

Set-Mount

3. Anchors (3EA)

2. Bracket

Wall-Mount

4. Screws (3EA) Wall-Mount

5. Screws (4EA)

(Contact a local Samsung Electronics service center to buy optional items.)

1. VESA Mounting Bracket

2. Attaching a base

(2)

(1)