Samsung RIF-BT10 User Manual

Bluetooth user manual

(RIF-BT10)

Table of Contents

1. Hardware, & Software ------------------------------------------------------------------ 2

2. Specifications ----------------------------------------------------------------- 3

3. System Structure ----------------------------------------------------------------- 4

4. How to configure ----------------------------------------------------------------- 5

Attachment 1. Virtual serial port driver installation

Attachment 2. Virtual serial port setting

Attachment 3. Dip switch setting

Attachment 4. Bluetooth slave setting

Attachment 5. Bluetooth master setting

Attachment 6. Printer driver installation & Test page printing

V1.00 WWW.SAMSUNGMINIPRINTERS.COM

1. Hardware & Software

1) Hardware

Bluetooth Main (Master & Slave) Bluetooth Connection PCB

(RIF-BT10) (RIF-BT10C)

Cable_USB_BT Cable_Serial_BT

2) Software & manual

(1) USB virtual serial port driver (Win98, 2000, XP): VirtualCOM_R9032148

(2) System configuration program: BluetoothConfig_V2.x

(3) Window printer driver: Download from website

- SRP 350: V3.0.5E above

- SRP 270: V3.0.3E above

(4) Application programmer’s guide: Bluetooth control message V1.x

3) Ordering information

(1)USB Master (RIF-BT10U) = RIF-BT10 + Cable_USB_BT

(2)Serial Master (RIF-BT10S) = RIF-BT10 + Cable_Serial_BT + (5V Power adapter option)

(3)Slave (RIF-BT10F) = RIF-BT10 + RIF-BT10C

V1.00 WWW.SAMSUNGMINIPRINTERS.COM

2. Specifications

Category Specification

Model name RIF-BTM10

Connection System

(Printer : SRP-350, SRP-270)

POS System

Interface Port USB(PC), RS-232C(PC), UART(Printer)

Flow control Hardware(RTS/CTS)

Transmission speed (bps) 19200,9600

Power

(USB port or RS-232C Pin 9 or Printer power)

DC 5V/150mA

Bluetooth Specification V1.0B & V1.1

Service Distance Max 100 m (Class 1)

Network Support

(Master: Slave)

Multi-Connection Support = N:7(max N=infinity)

Simultaneous printing = 1 : n (max. n=7)

SPP(Serial Port Profile) &

Printing Profile Support

HCRP(Hardcopy Cable Replacement Profile)

Dimensions(W x L x H) 70 x 45 x 11 mm

Rx/Tx Buffer

Rx Buffer: 1024 byte Tx Buffer: 512 byte

V1.00 WWW.SAMSUNGMINIPRINTERS.COM

3. System structure

Connect Bluetooth master module to the USB port (or Serial) of PC and Bluetooth slave module to the

printers.

1) A network between PC (Master) and Printers (Slave) is n : n. The number of PC can be infinite on

network while printers can be max up to 7.

2) Master can designate the printer for use after finding all the printers installed around.

(Refer to Application programmer’s guide for developing Bluetooth application program)

3) Master can save Bluetooth address of the printers up to 7 and then no need to search for printers

4) Master can send data to max 7 printers at the same time.

5) Bluetooth compatible module like PDA also can use the printer.

V1.00 WWW.SAMSUNGMINIPRINTERS.COM

4. How to configure

1) Virtual serial port driver installation (required only when you use the USB port on the PC)

- Connect Bluetooth main (master) to USB port of PC (Refer to Attachment 3. Dip switch setting)

- Found New Hardware Wizard detects new hardware by Plug and Play and select Include this

location in the search. Then select the folder which contains VirtualCOM_R9032148.

- When installation completes, Found New Hardware Wizard will detects new hardware once again.

Then repeat the above setting one more time.

- Refer to Attachment 1.Virtual serial port driver installation.

2) Virtual serial port driver setting (required only when you use the USB port on the PC)

- Check Virtual port and apply the setting as below.

- Start > Control Panel > System > Hardware > Device Manager

- Select USB Serial Port under Port (COM x: Port number varies from your PC condition) and change

the Properties.

- Port Setting: 19200, 8, none, 1, hardware

- Advanced Setting: 4096, 4096, 16, 0, 0,

Check in “Serial Enumerator” and “Serial Printer” .

(In case of Win 98, You cannot see “miscellaneous option” Just ignore)

- Make sure not to change COM Port Number (When changes, select the open port)

- Refer to Attachment 2. Virtual serial port setting

3) Bluetooth & Printer dip switch setting

- Set Maser/Slave, Baud rate and handshaking by Dip switch.

- 19200 bps, DTR/DSR (RTS/CTS) (Be sure that communication condition must be all the same for

PC, Bluetooth master, Bluetooth slave, Printer)

- Refer to Attachment 3. Dip switch setting

4) Bluetooth slave setting

- Connect Bluetooth main (master/slave) to USB (or Serial) port of PC.

- Execute BluetoothConfig_V2.x.exe from the downloaded files.

- Select the virtual port

a) USB port: Select the virtual port (COM x) of step 2).

b) Serial (RS-232C): Select the COM x connected.

- Configure Adapter setting: slave, 19200, hardware

- Disconnect the Bluetooth main (master/slave) from the PC, assemble it with the Cover_BT, and

connect it to the printer.

- Refer to Attachment 4. Bluetooth slave Setting

V1.00 WWW.SAMSUNGMINIPRINTERS.COM

5) Bluetooth master setting

- Connect Bluetooth main (master/slave) to USB (or Serial) port of PC.

- Execute BluetoothConfig_V2.x.exe from the downloaded files.

- Select the port

a) USB port: Select the virtual port (COM x) of step 2).

b) Serial (RS-232C): Select the COM x connected.

- Configure Adapter setting: master, 19200, hardware

- Register Printer setting: Search the printers around and save the printer address by

button “Search”. Make sure the printers are all power on mode.

- Configure Adapter setting: Check in auto connector to printers.

- Click “ok”.

- Refer to Attachment 5. Bluetooth master Setting

6) Printer driver installation & Test page printing

- Once the setting’s complete, disconnect the Bluetooth master from the PC, reconnect it and initialize

the system. Turn the printer off and then on to initialize the Bluetooth slave.

- Wait for approximately 20 seconds for the Bluetooth master and slave are automatically

reconnected.

- Install the printer driver (Available at website)

a) SRP 350: V3.0.5E above

b) SRP 270: V3.0.3E above

- You can download the printer driver from the homepage. Make sure that you delete the older version

driver from the PC before you install the new one(Clean register)

- Open the printer driver and select a port

a) USB port: Select the virtual port (COM x) of step 2).

b) Serial (RS-232C): Select the COM x connected.

- Set the port settings as below (19200, 8, none, 1, hardware)

- Test Page Printing.

- Refer to Attachment 6. Test page printing

7) Other

- If you are a POS Application Programmer, refer to the manual below for more information.

: “Bluetooth control message V1.x

V1.00 WWW.SAMSUNGMINIPRINTERS.COM

+ 11 hidden pages