operation/performance, parts, accesories or service, call:
1-800-726-7864 (1-800-SAMSUNG)
www.samsung.com
Register your product at www.samsung.com/global/register
DA99-01278D REV(0.0)
SAFETY WARNING SIGNS
• Before operating the appliance, please read and retain this manual thoroughly for your reference.
• The appliance is not intended for use by children or infirm persons without adult supervision.
WARNING
CAUTION/WARNINGS USEDOTHER SIGNS USED
WARNING
CAUTION
Please follow the safety warning signs to prevent injury to users or other persons.
After reading the warning signs, keep them in a safe place for future reference.
• Children should be supervised to ensure that they do not play with the appliance.
Represents something you must NOT do.
Represents something you must NOT
Indicates that a danger of
death or serious injury exists.
disassemble.
Represents something you must NOT touch.
Represents something you must follow.
Indicates that you must disconnect the
Indicates that a risk of
personal injury or material
damage exists.
power plug from the socket.
Represents that a ground is needed to prevent electric shock.
It is recommended that this should be handled by a service center.
WARNING SIGNS
Do not plug several appliances into the same multiple
receptacle.
• This could cause overheating and the risk of fire.
Make sure that the power plug is not squashed or damaged by the back of the refrigerator .
• A damaged power plug may cause overheating and fire.
Do not directly spray water inside or outside the refrig-
/ freezer.
erator
• There is a risk of electric shock.
Do not use aerosols near the refrigerator .
• There is a risk of explosion or fire.
Do not bend the power cord excessively or place heavy
articles on it .
• This constitutes a fire hazard. If the power cord is damaged, have it replaced immediately by the manufacturer
or its service agent.
Do not insert the power plug with wet hands.
• You may receive an electric shock.
Do not put a container filled with water on the refrigerator.
• If spilled, there is a risk of fire or electric shock.
Do not install the refrigerator in a damp place or a
place where it may come in contact with water.
• Deteriorated insulation of the electrical parts may cause
electric shock or fire.
Do not store volatile or flammable substances in the
refrigerator.
• The storage of benzene, thinner, alcohol, ether, LP gas
and other such products may cause explosions.
Do not disassemble or repair the
self.
• You run the risk of causing a fire, malfunctions and/or
personal injury.
refrigerator
by your-
2
Pull the power plug out of the socket before changing the refrigerator’s interior light.
• Otherwise, there is a risk of electric shock.
If you wish to dispose of the
by first removing the doors and seals.
• Do so in a way that it is not possible for a child to remain
trapped inside.
The refrigerator must be grounded.
You must ground the refrigerator to prevent any power
•
leakages or electric shocks caused by current leakage
from the refrigerator.
Never use gas pipes, telephone lines or other potential lightning rods as ground.
Improper use of the ground plug can result in a risk of electric shock.
•
If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade ground plug and a 3-slot receptacle that
will accept the plug on the appliance. The marked rating of the
extension cord should be AC 115V~120V, 10A, or more. If a grounding adapter is used, make sure the receptacle box is fully grounded.
You should use only the power adaptor which is provided with the
I.C.E. PAD.
- Otherwise, it may cause malfunction and the risk of fire.
Do not heat the I.C.E. PAD and do not place it inside in the refrigerator.
- It may cause damage such as explosion fire or electric shock.
Do not connect between charging terminals of I.C.E. PAD bottom side.
- This can cause reduced battery life, malfunction, explosion and electric
shock.
When you use your I.C.E. PAD, it should be used in the open area for
proper ventilation.
Do not disassemble or repair the I.C.E. PAD by yourself.
- You run the risk of causing a fire, malfunction and/or personal injury.
When you use your I.C.E. PAD, keep your body in a comfortable and
relaxed position.
refrigerator,
throw it away
SAFETY WARNING SIGNS
CAUTION SIGNS
Do not overfill the refrigerator with food.
• When you open the door, an item may fall out and cause
personal injury or material damage.
Do not put bottles or glass containers in the
• When the contents freeze, the glass may break and
cause personal injury.
If the wall socket is loose, do not insert the power
plug.
• There is a risk of electric shock or fire.
Do not disconnect the power cord by pulling on it.
• Damage to the cord may cause a short-circuit, fire and/or elec-
tric shock.
• I
f the power cord is damaged, it must be replaced by the manu-
facturer, a certified service agent or qualified service personnel.
Do not store articles on the top of the appliance.
• When you open or close the door, the articles may fall and
cause personal injury and/or material damage.
Do not store pharmaceutical products, scientific materials and
temperature-sensitive products in the refrigerator.
• Products that require strict temperature controls must not be
stored in the refrigerator.
Do not let children hang on the door because a serious
injury may occur.
If you sense pharmaceutical smells or smoke, pull out the
power plug immediately and contact your SAMSUNG
Electronics service center.
Do not touch the inside walls of the freezer or products
stored in the freezer with wet hands.
• It may cause frostbite.
Do not insert your hands into the bottom area under the
appliance.
• Any sharp edges may cause personal injury.
Never put fingers or other objects into the
dispenser hole and ice chute. It may cause personal injury
or material damage.
I.C.E. PAD is designed only for household use.
• Do not operate outside.
• If you use the I.C.E. PAD outside, wireless communication
between the I.C.E. PAD and Transmitter may fail.
Do not drop the I.C.E. PAD.
• Adult supervision should be maintained when children are
operating the unit.
• It may cause malfunction and personal injury.
Do not try to remove or reattach the I.C.E. PAD without first
reading the owner’’s manual.
• You need to connect to the adapter or put the I.C.E. PAD in the
docking station of the refrigerator door when the low battery
signal comes on. Otherwise, you may lose unsaved data.
Do not use sharp material (Pencil, nail, etc.) to touch the LCD.
• It may easily damage the touch screen.You should use the sty-
lus pen which is provided with the I.C.E. PAD product.
The LCD screen may appear different.
•
It is not a malfunction, but due to viewing the screen from different angles, different amounts of light, and ambient temperatures.
To clean the I.C.E. PAD screen, wipe with a smooth and dry cloth.
• Do not spray water or detergent directly on the monitor.
freezer
.
3
DANGER
Risk of child entrapment. Before you throw away
your old refrigerator or freezer
• Take off the doors
• Leave the shelves in place so that children may not
easily climb inside.
SAFETY WARNING SIGNS
Do not use a wet or damp cloth when cleaning the
plug. Remove any foreign matter or dust from the
power plug pins.
• Otherwise there is a risk of causing a fire.
• If the refrigerator is disconnected from the power
supply, you should wait for at least five minutes
before plugging it back in.
If the refrigerator is not to be used for a long
period of time, pull out the power plug.
• Deterioration in the insulation may cause fire.
• The appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that
they do not play with the appliance.
• Do not place the equipment directly under the sunlight, etc.
• The appliance must be positioned so that the plug is
accessible after installation.
• If the power cord is damaged, it must be replaced
by the manufacturer, a certified service agent or a
qualified service personnel.
• If you have a long vacation planned, empty the
refrigerator and turn it off. Wipe excess moisture
from the inside and leave the doors open.
Otherwise, odor and mold may develop.
Service warranty section
• Any changes or modifications performed by a 3rd party on a fin-
ished product is not covered under Samsung warranty service
Safety Caution section
• Samsung does not recommend 3rd party modification, there-
fore Samsung is not responsible for safety issues that result
from 3rd party modifications.
• Any changes or modifications in construction of this device
which are not expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY
AND MUST BE RECYCLED OR DISPOSED OF ACCORDING
TO LOCAL, STATE OR FEDERAL LAWS.
For details see lamprecycle.org,eiae.org,or call 1-800-Samsung.
SETTING UP THE REFRIGERATOR
Once you have performed the following steps, your refrigerator should be fully operational. If not, check
the power supply and electricity source. If you have any questions, contact your SAMSUNG
service center.
Place the refrigerator in an appropriate
location with reasonable clearance
between the wall and the refrigerator.
(refer to installation instructions in this
manual)
When the refrigerator is plugged in,
the interior light should come on when
you open the doors.
MAJOR FEATURES
Twin Cooling System
•
The refrigerator and the freezer have two evaporators. Given this independent system, the freezer and the refrigerator are cooled individually and are, therefore, more efficient. Food odor from the refrigerator
does not affect food in the freezer due to separate air flow circulation.
Multi-Flow System
•
Cool air circulates through multiple vents on every shelf level. This provides even distribution of cooling inside cabinets to keep your food
fresh longer.
Xtra Space
• Vertical room next to the ice maker in the freezer provides space for
pizza etc.
Set the temperature control to the coldest
temperature and wait for an hour. The
freezer should get slightly chilled and the
motor should run smoothly.
Once the refrigerator temperature is sufficiently low, you can store food in the
refrigerator. After starting the refrigerator, it
takes a few hours to reach the appropriate
temperature.
TM
Door Alarm
•
Beeper reminds you that the door is open.
Xtra Fresh
• Optimized humidity control keeps vegetables & fruits fresh.
Deodorizer
• Reusable deodorizer keeps the refrigerator air fresh and odor free.
CoolSelect Zone
• You can select Quick Cool, Thaw and Select buttons to quickly chill,
thaw and cool items. Select Soft Freeze, Cool or Chill to control the
temperature of drawer.
TM
TM
Drawer
4
CONTROL PANEL
FREEZER BUTTON
To set the freezer temperature, press this
button repeatedly to change the set temperature in sequence between
8°F and -14°F.
COOLING OFF
Cooling off stops cooling in both the freezer and refrigerator compartments but does not shut off electrical
power to the refrigerator.To use this feature, press the
freeze and power freeze buttons simultaneously for 3
seconds until a "beep" sounds. To cancel this mode,
press the same buttons again for 3 seconds.
POWER FREEZE BUTTON
Speeds up the freezing process in the freezer.
ICE TYPE BUTTON
Use this button to choose Cubed or
Crushed Ice or Ice off.
FRIDGE BUTTON
To set the fridge temperature, press this button
repeatedly to change the set temperature in
sequence between 34°F and 46°F.
POWER COOL
Speeds up the cooling process in the
CHILD LOCK BUTTON
When this button is pressed for 3 sec., the Power Freeze,
Power Cool, Freezer Temp. and Fridge Temp. are locked and
can not be modified. The Water and Ice dispensers are not
locked and can still be used. To cancel this function, press the
Child Lock button again.
refrigerator
OPERATING INSTRUCTIONS
5
DIGITAL PANEL
Freezer indicates the current freezer temperature.
Fridge indicates the current
Quick Cool, Thaw, and Select show the status of the CoolSelect Zone
Power Freeze
This light goes on when you press the Power Freeze button.
•
Press this button to quickly return the freezer to its set temperature.
This feature enables you to get ice faster.
•
Press the button again to cancel the Power Freeze mode.
•
If you use this function, energy consumption will increase.
refrigerator
temperature.
TM
Drawer
Power Cool
This light goes on when you press the Power Cool button.
•
Press this button to quickly return the refrigerator to its set temperature.
Press this button again to cancel the Power Cool mode.
•
Cubed Ice, Crushed Ice and Ice Off
Filter Indicator
Change filter every 6 months. If indicator is orange, the filter has 1 month left.
•
If indicator is red, quick replacement is strongly recommended.
When the water filter is replaced, reset the indicator by pressing the Ice Type
•
button and the Child Lock buttons simultaneously for 3 seconds.
To turn this indicator off, press the Ice Type and Child Lock buttons simultane-
•
ously and hold for 5 seconds.
Press the Ice Type button in sequence to choose
•
Cubed Ice, Crushed Ice or Ice Off to stop making ice.
Lit icon indicates the ice type currently chosen.
•
6
TEMPERATURE CONTROL
Freezer
The freezer temperature can be set between
•
8°F and -14°F.
Press the Freezer. button repeatedly until the desired
•
set temperature is shown in the temperature display.
The temperature display changes in sequence
•
between 8°F and -14°F. When the display reaches
8°F, it returns to -14°F.
After five seconds, the display reverts to the actual
•
freezer temperature. The unit will then work to adjust to
the new desired temperature.
When ice cream is stored at a temperature above 4°F in freezer, it may melt.
•
The temperature of the freezer or the refrigerator rises from frequent door opening
•
WARNING
and warm food. This may cause the digital display to blink. The digital display will stop
blinking when the freezer and refrigerator return to normal temperature.
Refrigerator
The refrigerator temperature can be set between
•
46°F and 34°F.
Press the Fridge. button repeatedly until the desired
•
temperature is shown in the temperature display.
The temperature display changes in sequence and
•
reverts in the same way as the freezer.
If the temperature control does not reset the temp, unplug the refrigerator, wait 9 min, then plug it back in.
ICE and COLD WATER DISPENSER
Press the Ice Type button to select the type
of ice:
Cubed ice
•
Crushed ice
•
No ice
•
NOTE
If the Ice remains in the Ice bucket,
cubed ice is obtained. Ice stays in cube
form and is crushed when the Crushed
ice button is pressed.
No ice
Water Dispenser
The capacity of the water tank is approximately 0.3
gal.
Cold Water
Push the water dispenser lever with a cup.
•
If you have just installed the refrigerator or
•
installed a new water filter, throw away the first
six glassfuls of water or until water flows cleanly
to flush out impurities in the water supply system.
Push
OPERATING INSTRUCTIONS
Push the ice dispenser lever with a cup.
Place a cup in line with the dispenser to prevent
•
ice from jumping out.
Push
To avoid injury, never put fingers or
NOTE
any other objects in the dispenser
opening.
CAUTION
7
If there will be a long period of time (long
vacation or business trip) where you won’t
use the water or ice dispensers, close the
water valve and shut off the water supply
to the refrigerator. Otherwise, water leakage may occur.
SHELVES AND BINS
Freezer
Xtra Space
Door Bin
Ice Maker
Light
Ice Chute
Glass Shelf
Wire Shelf
Light Switch
Tilt Pockets
Plastic Drawers
Wire Drawers
Front Leg Cover
TM
Refrigerator
Water Filter Compartment
Light (upper)
Spill-proof glass Shelf
Light Switch
Foldable Shelf
Deodorizer
Egg Container
CoolSelect Zone
Vegetable & Fruit Drawers
TM
Drawer
Dairy Compartment
Wine Shelf
Gallon Door Bin
Light (lower)
Door Bin Top Lip
Gallon Door Bins
8
FOOD STORAGE GUIDE
FROZEN FOOD STORAGE IN FREEZER
Ice chute
Do not put your fingers, hands or any other unsuitable objects in the chute or ice-maker bucket,
WARNING
as this may result in personal injury or material damage.
Door Bin
Can be used for small packages of frozen food.
•
Xtra Space
Can be used for frozen foods such as pizza, pasta, burritos,
•
and fajitas.
In order to prevent odor penetration to the ice, stored food
•
should be wrapped securely.
Tempered Glass Shelf
Can be used to store all types of frozen food.
•
Plastic Drawer
Can be used to store meats and dry foods. Stored food should be
•
wrapped securely using foil or other suitable wrapping materials
or containers.
TM
OPERATING INSTRUCTIONS
9
FOOD STORAGE GUIDE
CHILLED FOOD STORAGE IN REFRIGERATOR
Wine Shelf
Place your wine bottles on the shelf to maintain their taste.
•
Tempered Spill Proof Glass Shelf
Can be used to store all types of chilled food.
•
Safe and break resistant.
•
Circular marks on the glass surface are a normal phenomenon.
•
Egg Container
•
Put eggs in the container and place them on the shelf.
WARNING
Chilled Bin or CoolSelect Zone
•
Helps to preserve the taste of food and prolongs its freshness. Use
to store cheese, meat, poultry, fish or any other foods used quickly.
Fruit & Vegetable Drawer (Upper and Lower)
Is used to store fruits and vegetables.
•
This drawer is airtight. Optimized humidity control design helps to
•
preserve the freshness of the stored vegetables and fruits.
Dairy Compartment
Can be used to store butter or margarine.
•
Gallon Door Bins
Can be used to store foods in packages, such as milk and yogurt.
•
If you have a long vacation planned, empty the refrigerator and turn it off. Wipe excess moisture
•
from the inside and leave the doors open. Otherwise, odor and mold may develop.
TM
Drawer
10
CoolSelect Zone
TM
“Quick Cool” Button
You can use the Quick Cool feature with the CoolSelect ZoneTM.
•
“Quick Cool” allows 1~3 canned beverages to cool within 60 min.
•
To cancel this option, press the “Quick Cool” button again.
•
CoolSelect Zone
When “Quick Cool” ends, it returns to the “Cool” temperature set-
•
ting.
TM
returns to the previous temperature.
Drawer GUIDE
NOTE
NOTE
Depending on the beverages, the cool-down time may vary.
When the “Quick Cool” option is selected, remove food stored in the
•
CoolSelect ZoneTMDrawer that you do not want to cool.
“Thaw” Button
After “Thaw” is selected, warm and cold air is alternately sup-
•
plied into the
Depending on the weight of the meat, thawing time can be
•
selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs sequentially, keeping the meat partially frozen.
When “Thaw” ends, the
•
“chill” condition.
When “Thaw” ends, meat is in a half-frozen state so it is
•
easy to cut for cooking.
To cancel this option, press any button except “Thaw”.
•
The approximate thawing times of meat and fish are shown
•
below. (Based on 1inch thickness)
CoolSelect ZoneTMDrawer
CoolSelect Zone
.
TM
display returns to
OPERATING INSTRUCTIONS
NOTE
NOTE
Thaw
Time4 hours6 hours10 hours12 hours
Weight0.8 lb1.3 lb1.7 lb2.2 lb
Depending on the size and thickness of the meat and fish, the thawing time may vary.
The above chart represents the total weight of food in the CoolSelect Zone
Ex) The total thawing time for 1.3 lb frozen beef and 0.8 lb frozen chicken will be 10 hours.
When the “Thaw” option is selected, be sure to remove food stored in the CoolSelect ZoneTMDrawer
•
that you do not want to thaw.
11
TM
Drawer.
CoolSelect Zone
TM
“Select” Button
Soft Freeze
When “Soft Freeze” is selected, the temperature on the
•
digital panel displays 23°F(-5oC), regardless of the set
temperature of the refrigerator.
“Soft Freeze” temperature helps keep meat and fish
•
fresh for longer.
Chill
Drawer GUIDE
When “Chill” is selected, the temperature of the
•
lect Zone
the set refrigerator temperature.
“Chill” temperature helps keep meat or fish fresh for
•
longer.
Cool
When “Cool” is selected, the temperature will be the
•
same as the set temperature of the refrigerator. The digital panel shows the same temperature as that of the
Control panel.
When using “Cool”, the CoolSelect ZoneTMDrawer allows
•
extra refrigerator space.
TM
Drawer is kept at 30°F(-1oC), regardless of
CoolSe-
12
REMOVING THE FREEZER ACCESSORIES
Glass Shelf
Pull the shelf out as far as
•
it goes. Then lift it up and
remove it.
Door Bin
Hold the door bin with both
•
hands and then lift it up.
Plastic Drawer (Wire
Drawer)
Remove the drawer by
•
pulling it out and slightly lifting it up.
Ice Maker Bucket
Remove the bucket by lifting up and pulling out.
•
Front Leg Cover
Open the freezer and refriger-
•
ator doors, remove three
screws and detach the cover.
To reattach the front leg cover,
•
put it back to original position
and tighten the three screws.
Do not use excessive force when
•
NOTE
removing the cover. It may cause an
injury.
REMOVING THE REFRIGERATOR ACCESSORIES
Spill Proof Glass Shelf
Pull the shelf out as far as it will go. Then lift it up and gently remove it.
•
OPERATING INSTRUCTIONS
Vegetable & Fruit Drawer
Remove the drawer by holding the handle, pulling the drawer out and lifting it up smoothly.
•
Remove the optimized humidity control cover by pulling it towards you.
•
Gallon Door Bin
Hold the bin with both hands and remove by lifting it up.
•
Wine Shelf
It is attached to the cabinet wall. To remove the wine shelf, lift it up in the direction
•
of the arrow as shown.
•
Simply take the shelf out of the tabs.
Before
NOTE
•
removing the freezer and refrigerator accessories, please remove the stored foods.
13
CARE AND CLEANING
Interior
Clean the accessories with a mild detergent, then wipe out with a dry cloth.
•
After washing the accessories, make sure that they are dry before using them again.
•
Exterior
Wipe the digital panel and display panel with a clean cloth.
•
Clean the surface of doors, handles and cabinet with a mild detergent and soft cloth, then
•
wipe off the surface with a dry cloth.
- Do not use Benzene, Thinner or CloroxTMfor cleaning
- Do not spray water directly on the surface of the refrigerator while cleaning.
The exterior part of the refrigerator should be polished once or twice a year.
•
Rear
Use a vacuum cleaner to remove dust once or twice a year.
•
Do not remove cover, risk of shock.
•
WARNING
Ice and water dispenser
Use a damp cloth to clean the ice and water dispenser.Then wipe it out with a dry cloth.
•
To keep drainage grid dry, do not touch ice and water dispenser without a cup or glass in
•
place.
Rubber door seals
If the rubber door seals are dirty, the door will not close properly, The refrigerator will not be
•
able to function efficiently. Clean the doors with a mild detergent and damp cloth. Then wipe
with a dry cloth.
Do not spray the refrigerator with water. It may cause a serious electric shock.
•
Do not clean it with benzene, thinner or car detergent. It may cause a fire.
WARNING
•
14
CARE AND CLEANING
Twin Deodorizer
Remove the cover with a flat blade screw driver as shown.
•
Take out the cartridge from the cover and soak it in clean, warm water for at least
•
4 hrs. Completely dry out the cartridge in sunlight for at least 8 hrs in an open area.
Repeat this process once or twice a year.
•
If cartridge is dried in a confined area, there may be some odor.
•
NOTE
Keep children away from contaminated water.
•
CHANGING THE INTERIOR LIGHT
Before changing the interior light, unplug the
WARNING
have difficulty changing the light, contact your service center.
INTERIOR LIGHT IN THE REFRIGERATOR.
Upper
The upper light is located in the upper center of the refrigerator.
Place a flat screwdriver under
the light cover hooks and push
in the direction of the arrow.
Replacement bulbs for the upper refrigerator are available at retail outlets such as
NOTE
Wal-mart and The Home Depot. Use replacement bulb size E26, maximum 40 watts.
Lower
The lower light is located in the lower center of the refrigerator.
Pull the cover in the
direction of the arrow.
refrigerator
from the power supply. If you
After changing the
bulb, replace the light
cover.
E26
40W
OPERATING INSTRUCTIONS
NOTE
Place a flat screwdriver under
the light cover hooks and push
in the direction of the arrow.
Replacement bulbs for the lower refrigerator are available at retail outlets such as
Wal-mart and The Home Depot. Use replacement bulb size E17, maximum 30 watts.
Change the bulb
with a new one (
15
➁
After changing the
)
bulb, replace the light
cover.
E17
30W
CHANGING THE INTERIOR LIGHT
INTERIOR LIGHT IN THE FREEZER
The freezer light is located in the bottom of the auger motor case.
Use a screwdriver(+) to
remove the screw (➀).
Replacement bulbs for the freezer are available at retail outlets such as Wal-mart and The Home
NOTE
Depot.
Use replacement bulb size E26, maximum 40 watts.
.
Change the bulb with a new
one (➁)
E26
40W
Reattach the light cover
WATER FILTER
The water “Filter Indicator” light
“Filter Indicator” light lets you know when it is time to change your water filter cartridge. The light
•
will change from green to orange. This tells you that it is almost time to change the current cartridge.
It is recommended that you replace the cartridge when the light changes to red.
(see “Install the water filter” section for more information)
If you install the water filter, throw away the first six glassfulls of water filter, or until water flows clearly
•
to flush impurities in the water supply system.
Using the dispenser without the water filter
You can not use the water and ice dispenser without a water filter cartridge because the water line
•
blocks at the water supply.
Ordering replacement filters
To order more water filter cartridges, call 1-800-SAMSUNG and ask for accessory Part # DA29-
•
00003B or contact your authorized Samsung dealer.
DOORS
The refrigerator doors have a special door opening and closing feature to make sure that they close all
the way and are securely sealed.
When opening the door, it will only open so far. After reaching a certain point, it will remain open.
When the door is partially open, it will close automatically.
The refrigerator should be properly installed & leveled.
16
INSTALLATION OF THE REFRIGERATOR
Checking the Dimensions of your Entrance Door
Check the dimensions of your entrance door to determine whether the refrigerator can pass
through it.
Dimension
(inches)
• Select a location with easy access to the water supply.
• Select a location with enough space for the refrigerator.
• Select a location without direct exposure to sunlight.
• Select a location with level floor or close to it.
NOTE
Capacity (Cu. Ft)
Case Height
Depth
Width
without Hinge
with Hinge
with door
without door
26.1
35.9"
68.8"
70"
36.5"
30.5"
Selecting the Location for the Refrigerator
• Before removing the freezer door, the water supply line needs to be disconnected.
(If not, the water supply line may be damaged.)
• See “Separating the water supply line from the refrigerator” on the next page.
Allow sufficient space to circulate the air in the internal cooling system.
When the refrigerator does not have enough space, the internal cooling system may not work correctly.
•
NOTE
inches
4
2 inches
0.1inch
●
Allow clearance to the right, left, back and top when installing the refrigerator.
This has the advantage of reducing power consumption.
●
Do not install the refrigerator where the temperature will go below 50°F(10°C).
17
INSTALLATION INSTRUCTIONS
REMOVING THE REFRIGERATOR DOORS
Removing the Front Leg Cover
Open the freezer and refrigerator doors, and then take off the front leg cover by turning the
three screws counter-clockwise.
a
FRONT LEG COVER
SCREW
Separating the Water Supply Line from the Refrigerator
1) Remove the screw from clamp ( ).
2) Remove the water tube by pressing the coupler (➁) and pulling the water tube (➀) away.
Turn off the water supply when separating the water supply line.
NOTE
a
NOTE
a
Do not cut the water tube. Separate it from the coupler.
18
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.