Samsung RFG29THDRS/XAA-01, RFG29THDRS/XAA-00, RFG29PHDWP/XAA, RFG29PHDRS/XAA, RFG29PHDBP/XAA-02 Owner’s Manual

the possibilities

Thank you for purchasing this Samsung product.
To recewe more complete service or accessory parts,

please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

Free Standing Appliance

DA68-02488A-09.indb 1 13.4.25. DD 2:07

SAFETY INFORMATION

Before using your new Samsung French Door
Refrigerator, please read this manual thoroughly to
ensure that you know how to operate the features and

functions that your new appliance offers safely and

efficiently.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory, or
mental capabilities, or those who lack experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a
person responsible for their safety.

Because the following instructions cover various
models, the characteristics of your refrigerator may
differ slightly from the refrigerator described in this

manual. If you have any question, contact us at
1-800-SAMSUNG or find help and information online

at www.samsung.com.

important safety symbols and precautions:

Hazards or unsafe practices that may result in

WARNINGsevere personal injury or death.

Hazards or unsafe practices that may result in

CAUTION minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded to
prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent injury to
you and others.

Please follow them carefully.

After reading this section, keep it in a safe place
for future reference.

CRITICAL INSTALLATION

WARNINGWARNINGS

, Do not install the refrigerator in a damp place or

place where it may come in contact with water.

- Deteriorated insulation of electrical parts may cause
an electric shock or fire.

• Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters or

other appliance.

• Do not plug several appliances into the same
multiple power strip. The refrigerator should always

be plugged into its own individual electrical outlet
which has a voltage rating that matches the voltage

listed on the refrigerator's rating plate.

- This provides the best performance and also
prevents overloading house wiring circuits, which

could cause a fire hazard from overheated wires.

• If the wall socket is loose, do not insert the power plug.

- There is a risk of electric shock of fire.

• Do not use a cord that shows cracks or abrasion
damage along its length or at either end.

• Do not bend the power cord excessively or place
heaw articles on it.

• Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull straight

out from the outlet.

- Damage to the cord may cause a short-circuit, fire
and/or electric shock.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause an
explosion or fire.

, his refrigerator must be properly installed and

located in accordance with the manual before
you use it.

• Connect the power plug in the proper position with
the cord hanging down.

- Ifyou connect the power plug upside down, the wire
can get cut off and cause a fire or electric shock.

• When moving the refrigerator, be careful not to roll
over or damage the power cord.

- This constitutes a fire hazard.

• Make sure that the power plug is not squashed or
damaged by the back of the refrigerator.

• Keep the packing materials out of reach of children.

- There is a risk of death from suffocation if a child
puts the packing materials on his or her head.

• The appliance must be positioned so that the plug is
accessible after installation.

• You need to remove all the protective plastic film
before you initially plug the product in.

02 Safety informaton

DA68-02488A-09.indb 2 13.4.25. BB 2:07

o The refrigerator must be safely grounded.

- Always make sure that you have grounded the

refrigerator before attempting to investigate or repair

any part of the appliance. Power leakages can cause
severe electric shock.

• Never use gas pipes, telephone lines or other
potential lightning attractors as an electrical ground.

Improper use of the grounding plug can result in a risk

of electric shock. If it is necessary to use an extension
cord, use only a 3-wire extension cord that has a

3-blade grounding plug and a 3-slot receptacle that
will accept the plug on the appliance. The marked

rating of the extension cord should be AC115-120 V,
10 A, or more. If a grounding adapter is used, make

sure the receptacle box is fully grounded.

o If the power cord is damaged, have it replaced

immediately by the manufacturer or its service agent.

CAUTIONINSTALLATION CAUTIONS

o Allow sufficient space to install the refrigerator

on a flat surface.

If your refrigerator is not level, the internal cooling

system may not work correctly.

• Keep the ventilation space in the appliance enclosure

or mounting structure clear of obstruction.

• Allow the appliance to stand for 2 hours after installation.

• We recommend you have this refrigerator installed
by a qualified technician or service company.

Failing to do so may result in an electric shock, fire,

explosion, problems with the product, or injury.

A

WARNINGCRITICAL USAGE WARNINGS

o Do not insert the power plug with wet hands.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles
may fall and cause personal injury and/or material

damage.

• Do not put a container filled with water on the refrigerator.
If spilled, there is a risk of fire or electric shock.

• Children should be supervised to ensure that they

do not play with the appliance.

Keep fingers out of "pinch point" areas; clearances
between the doors and cabinet are necessarily small.
Be careful when you open the doors when children

are in the area.

• Do not let children hang on the door. A serious injury
may occur.

• Do not let children go inside the refrigerator.

Children could become trapped.

• Do not insert your hands into the bottom area under
the appliance.

- Any sharp edges may cause personal injury.

• Do not let children step on a drawer's cover.

- The drawer may break and cause them to slip.

• Do not overfill the refrigerator with food.

- When you open the door, an item may fall out and

cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Never put fingers or other objects into the water

dispenser hole, ice chute, or ice maker bucket.

- It may cause personal injury or material damage.

• Do not spray flammable gas near the refrigerator.

- There is a risk of explosion or fire.

• Do not store volatile or flammable substances in the

refrigerator.

- The storage of benzene, thinner, alcohol, ether, LP

gas and other such products may cause explosions.

• Do not store pharmaceuticals products, scientific

materials, or temperature sensitive products in the
refrigerator.

- Products that require strict temperature controls

must not be stored in the refrigerator.

• Do not place or use an electrical appliance inside the

refrigerator, unless it is of a type recommended by

the manufacturer.

• Do not stand on top of the appliance or place

objects (such as laundry, lighted candles, lighted
cigarettes, dishes, chemicals, metal objects, etc.) on

the appliance. This may result in an electric shock,
fire, problems with the product, or injury. Do not put

a container filled with water on the appliance.

- If spilled, there is a risk of fire or electric shock.

• Do not use mechanical devices or any other means
to accelerate the defrosting process, other than

those recommended by the manufacturer.

• Do not damage the refrigerant circuit.

[_o Do not disassemble or repair the refrigerator by

yourself.

- You run risk of causing a fire, malfunction and/or

personal injury.

- When the interior or exterior LED lamp has gone out,

please contact your service agents.

o hildren should be supervised to ensure that

they do not play with the appliance.

• Bottles should be stored tightly together so that they

Safety informaton 03

DA68-02488A-09.indb 3 13.4.25. BD 2:07

do not fall out.

o This product is intended only for the storage of food in

a domestic environment.
If a gas leak is detected, avoid any naked flames or

potential sources of ignition and air the room in which
the appliance is standing for several minutes.

Use only the LED Lamps provided by manufacturer or
service agents.

- Wrap food up properly or place it in airtight containers
before putting it into the refrigerator.
Fill the water tank, ice tray, and water cubes only with
potable water.

* f the product is flooded, make sure to contact

your nearest service center.

- There is a risk of electric shock or fire.

o f there are burning smells or smoke, pull out

power plug immediately and contact your
Samsung Electronics service center.
If you experience difficulty when changing the light,
contact a service agent.

If the product is equipped with LED Lamps, do not
disassemble the Lamp Cover and LED Lamp by yourself.

- Please contact your service agents.
If any dust or water is in refrigerator, pull out the power
plug and contact your Samsung Electronics service center.

- Otherwise there is a risk of fire.

A

CAUTIONUSAGE CAUTIONS

,, o not re-freeze frozen foods that have thawed

completely.
Do not place carbonated or fizzy drinks in the freezer
compartment. Do not put bottles or glass containers in

the freezer.

- When the contents freeze, the glass may break and
cause personal injury.

* Service warranty and Modification.

- Any changes or modifications performed by
a 3rd party on this finished appliance are not covered
under Samsung warranty service, nor can Samsung be
responsible for safety issues that result from 3rd party

modifications.
Do not block air holes.

- If the air holes are blocked, especially with a plastic
bag, the refrigerator can be over cooled. Ifthis cooling
period lasts too long, the water filter may break and
cause water leakage.
If the refrigerator is disconnected from the power
supply, you should wait for at least five minutes before
plugging it back in.
If you have a long vacation planned or the refrigerator
is not to be used for a long period of time, you must
empty the refrigerator and pull out the power plug.

- Letting the refrigerator run for a long time without using
it can cause the insulation to deteriorate and may

cause a fire.

- Wipe excess moisture from the inside and leave the
doors open. Otherwise, odor and mold may develop.
To get the best performance from the product:

- Do not place foods too close to the vents at the rear
of the appliance as it can obstruct free air circulation in
the refrigerator compartment.

CAUTIONCLEANING CAUTIONS

* o not directly spray water on the inside or outside

the refrigerator.

- There is a risk of fire or electric shock.
Do not use a hair dryer to dry the inside of the
refrigerator. Do not place a lighted candle in the

refrigerator to remove bad odors.

- This may result in an electric shock or fire.

_ emove any foreign matter or dust from the power

plug pins. Do not use a wet or damp cloth when

cleaning the plug.

- Otherwise, there is a risk of fire or electric shock.

* nplug the refrigerator before cleaning or making

repairs.

State of California Proposition 65

WARNING Warnings:

The California Safe Drinking Water and Toxic

Enforcement Act requires the Governor of California

to publish a list of substances known to the State
of California to cause cancer, birth defects, or other

reproductive harm, and requires businesses to warn of
potential exposure to such substances.

This product contains a chemical known to the State
of California to cause cancer, birth defects, or other

reproductive harm. This appliance can cause low-level

exposure to some of the substances listed, including

benzene, formaldehyde, and carbon monoxide.

WARNINGCRITICAL DISPOSAL WARNINGS

* isk of child entrapment. Before you throw away

your old refrigerator or freezer:

- Take off the doors.

- Leave the shelves in place so that children can not
easily climb inside.
Please dispose of the packaging material from this
product in an environmentally friendly manner.
Leave the shelves in place so that children can not
easily climb inside. Ensure that none of the pipes on the
back of the appliance are damaged prior to disposal.
R600a or R134a is used as a refrigerant. Check the
compressor label on the rear of the appliance or the
rating label inside the fridge to see which refrigerant

04 Safety informaton

DA68-02488A-09.indb 4 13.4.25. BD 2:07

is used for your refrigerator. If this product contains
flammable gas (Refrigerant R600a), contact your local
authority in regard to safe disposal of this product.
When disposing of this refrigerator, remove the door/

door seals and door latch so that small children or
animals cannot become trapped inside. Children

should be supervised to ensure that they do not play
with the appliance.

o Cyclopentane is used in the insulation. The gases in the

insulation material require a special disposal procedure.

Please contact your local authorities in regard to the
environmentally safe disposal of this product. Ensure
that none of the pipes on the back of the refrigerator
are damaged prior to disposal.

ntents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ................................................................................ 5

OPERATING YOUR FRENCH DOOR REFRIGERATOR ............................................................................... 11

TROUBLESHOOTING ................................................................................................................................. 23

WAR RANTY ................................................................................................................................................. 24

Sett ng up your French Door Refrgerator

GETTING READY TO INSTALL THE

REFRIGERATOR

Congratulations on your purchase of this Samsung
French Door Refrigerator.

We hope you enjoy the state-of-art features and
efficiencies that this new appliance offers.

Selecting the best location for the

refrigerator

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a leveled floor.

• A location with enough space for the refrigerator
doors to open easily.

• A location that allows sufficient space to the right,

left, back and top for air circulation.

• A location that allows you to move the refrigerator

easily if it needs maintenance or service.

2 in

If the refrigerator does not have enough space, the

internal cooling system may not work properly.

If your refrigerator has an ice maker, allow extra space

at the back for the water line connections.
When you install the refrigerator next to a fixed wall,

you need a minimum clearance of 3 s4" (95mm)
between the refrigerator and wall to allow the door to
swing open.

First thing! Make sure that you can easily move your
refrigerator to its final location by measuring doorways
(both width and height), thresholds, ceilings, stairways, etc.

The following chart details the exact height and depth
of this Samsung French Door Refrigerator.

Model Depth Width

RFG296**
RFG297** 33 35

RFG298** 1/8" 6/8"
RFG29P* (842mm) (908mm)

RFG29T*

o Allow clearance to the ., .....

right left back and top

when installing. / i :-'_

This will help reduce power | --1:

consumption and keep your / "--(_
energy bills lower. I

• Do not install the refrigerator I I ;
where the temperature will go I

below 50°F (10°C). _ __

Do not locate the refrigerator ..................-

where it may become wet.

"A .... B"

Height Overall Depth

"C" Height"D.... E"

68 69 35

1/2" 6/8" 5/8"

(1740mm) (1774mm) (904mm)

..... 7----..

setting up 05

DA68-02488A-09.indb 5 13.4.25. BD 2:07

When moving your refrigerator

To prevent floor damage, be sure the front

CAUTIONadjusting legs are in the up position

(above the floor). Refer to 'Adjusting the doors' in the
manual (on page 9).

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips Flat-blade screw Socket wrench

screwdriver(+) driver(-) (10mm)

Flat-blade Control Lever
screw driver(-)

FLOORING
For proper installation, you must place this refrigerator

on a level, hard surface that is the same height as the
rest of the floor. This surface should be strong enough

to support a fully loaded refrigerator, or approximately
3591bs (165kg).

To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working. When moving

the refrigerator, you need to pull and push it straight
forwards or back. Do not wiggle it from side to side.

Pliers

Allen wrench

(3/16") (5mm)

REMOVING THE REFRIGERATOR DOORS

For some installationsyou need to remove the fridge
and freezer drawers so you can move the refrigerator to its
final location. Do not remove the doors/drawer if you don't

need to. If you do not need to remove the refrigerator
doors, go to Adjusting the Level on page 8. If you need to

remove the doors, continue below. Before removing the
door/drawer, make sure you read the following items:

Z_ Disconnect power to the refrigerator before

WARNINGremoving the door or drawer.

o e careful not to drop, damage or scratch the

door/drawer while removing them.

o Be careful not to get injured while removing the

door/drawer.

o Reattach the door/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

ACCESSORIES AND REQUIRED
TOOLS

The following accessories are included with your

refrigerator:

Hex wrench Fastener

06 setting up

Disassemble the refrigerator doors

Z_ Be careful not to drop and scratch the doors

WARNINGwhile removing the doors.

Disassemble the refrigerator doors

=

With the door opened, remove the cap top table

( 1 ) with a flat-blade screwdriver(-), and close the
door. Remove 2 screws holding down the cover

hinge (2 ) and turn it with several wires connected.

DA68-02488A-09.indb 6 13. 4. 25. 13132:07

2. Disconnect one connector ( 3 ) on the right side door
and one connector ( 4 ) on left side door. To remove

the water coupler from the hinge, twist and pull it from
the hinge. Remove the water line ( 5 ) while pressing

the marked part ( 6 ) of the water line coupler.

If a red clip is on the coupler, it must be

CAUTIONremoved before removing the tube.

3. Pull and remove the hinge lever ( 2 ). Remove the
ground screw (8 ) attached to the upper left and
right door hinges with a philips screwdriver (+).
Remove the upper left and right door hinges (9 ).

REATTACHINGTHEREFRIGERATORDOORS

To reattach the fridge doors after you have moved the

fridge to its final location, assemble parts in reverse order.

1. The Water Line must be fully inserted to the center
of transparent coupler (Type A) or the line(Type B) to

prevent water leakage from the dispenser.

2. Insert the clip in the install pack and check that it

holds the line firmly.

Type A

f

CenterofTransparent¢oupler

Type B

Dispenser

J • J

DISASSEMBLE THE FREEZER DRAWER

1. Take out the upper drawer

by lifting it up.

4. Lift the door straight up to remove.

t

.

Remove the screw ( 10 ) attached to the lower left

and right door hinges with a philips screwdriver (+).

Remove the 2 hex head bolts ( 11 ) attached to
the lower left and right door hinges with an allen
wrench (3/16"). Remove the lower left and right
door hinges ( 12 ).

.

Remove the tilting pocket
( 1 ) by pulling both support

guards ( 2 ) upward at the
same time.

3. Take out the lower basket
( 3 ) by lifting the basket up

from the rail system.

4. Remove 4 hex head bolts
from both sides with a socket

wrench (10ram).

5. Lift up the freezer door from
the rails.

\

Putting too much food into the freezer drawers

CAUTION

can prevent the freezer from closing completely
and can cause frost build-up.

setting up 07

DA68-02488A-09.indb 7 13. 4. 25. 13132:07

ASSEMBLE THE FREEZER DRAWER

MAKING MINOR ADJUSTMENTS

To reattach the drawer after you have moved the
fridge to its final location, assemble parts in reverse

order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can
make final adjustments. Use a level to test if the
refrigerator is level both side to side and back to front.
If the refrigerator is not level, it will not be possible

to get the doors perfectly even, which may cause

moisture condensation and increased energy bills.
Below is an example of how to level the refrigerator if

the left side of the refrigerator is lower than the right
side.

How to adjust the level

1. Open the freezer drawer
and remove the lower

basket. (See to page 7)

2_

Remove the two screws
( 1 ) attached to the cover

leg front ( 2 ) with a Philips

screwdriver (+).

m

Remove the cover leg front
( 2 ) by lifting the bottom

part of the cover leg front
up and pulling it out.

m

Insert a flat-blade screwdriver (-) into a notch on the

left control lever, and turn it count clockwise to level
the refrigerator. (You turn the lever clockwise to lower
the refrigerator and counterclockwise to raise it.)

BETWEEN DOORS

Remember, a leveled refrigerator is necessary for
getting the doors perfectly even. If you need help,

review the previous section on leveling the refrigerator.

_tment

The left door is fixed. To make minor adjustments

between doors, adjust only the right door.

1. Pull out the freezer drawer ( 1 ), then you can see
the lower hinge ( 2 ).

2. Insert the supplied allen wrench(3!16") ( 3 ) into the
shaft ( 4 ) of the lower hinge.

3. Please adjust the height by turning the hex wrench
( 3 ) clockwise ( ) or counter-clockwise ( ).

When you turn the hex wrench counter-
clockwise( ), the door will move up.

%

flat-blade screwdriver(-) Control Lever

A

CAUTION

08 setting up

Both control levers must be touching the floor
to avoid possible personal injury or property
damage because of tipping.

lf the right side is lower, perform the same

procedure, but with the right control lever.

lt is difficult to remove the cover leg front from the

refrigerator, so we do not recommend making
small adjustments with the control lever. Instead,

refer to the next page for the best way to make
minor adjustments to the doors.

8}

1. After adjusting the doors, insert the supplied
fastener ( 6 ) using a pliers ( 5 ) in the gap between
the hinge-grommet ( 7 ) and the lower hinge

( 8 ). The number of fasteners you'll need to insert
depends on the gap.

®®

2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 0.04".

DA68-02488A-09.indb 8 13. 4. 25. 13132:08

ADJUSTING THE FREEZER DRAWER

LEVEL

INSTALLING THE WATER
DISPENSER LINE

Adjustment part

Freezer Drawer

1. Locate the height-adjuster ( 1 ) in the freezer drawer.
Unscrew the 8 Phillips screws ( 2 ) slightly to loosen

the door.

"Lt-

2. Loosen the controller
screw ( 3 ) with a Phillips

screwdriver (+).

A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need to
purchase a water purifying system to do that.

In order for the ice maker to operate properly, a water
pressure of 20-125 psi (138-862 kPa) is required.
Under normal conditions, a 170 cc (5.75 oz.) cup can

be filled in about 10 seconds.

If the refrigerator is installed in an area with low water
pressure (below 20psi), you can install a booster pump
to compensate for the low pressure.

After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly filled. To do this, press the water dispenser

lever until the water runs from the water outlet.

_ ater line installation kits are available at extra

cost from your dealer.

We recommend using a water line installation kit that
contains copper tubing and 1A" compression nut.

Connecting to the water supply line

1. First, shut off the main water supply.

3. Find the best level to align the door slope.
,, After adjustment, _,_,

tighten the

controller screw
and then the T_/_ t

philips screws.

Example) The slope is about 0.08inch (2mm) as shown below.

- Rotate the height adjuster to -2.0 to reduce the door slope.

A_

s

Reference

plane--

2. Locate the nearest cold water drinking line and
install the pipe
clamp and shut

off valve. Cold water line

3. Connect the water line installation kit to the shut off

valve.

Cold water line

Water line installation kit

setting up 09

DA68-02488A-09.indb 9 13. 4. 25. 13132:08

Connecting the water supply line to the

refrigerator.

There are several items that you need to purchase to
complete this connection.
You may find these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

I o 1A"copper tubing • 1A"plastic tubing

: F1A_'rrClOe(_rpe_Sionnut(1 pc) • _"M°ldmpdreenid(BUluLl(1pc)

Refrigerator

4. Flush 1 gallon of water through the filter before
drinking or using the water from the refrigerator.
(Flush approximately 6 minutes.) To flush, press a
large glass or cup against the water dispenser lever.

Fill the glass, empty it into the kitchen sink after it is

filled, and then repeat.

5. After you turn on the refrigerator, let the ice maker
make ice for 1 to 2 days. Over that period of time,

throw out the first 1 or 2 buckets of ice the freezer

makes to ensure all impurities have been removed

from the water line.

Only connect the water line to a drinkable water
source.

If you have to repair or disassemble the water line, cut
off 1/4" of the plastic tubing to make sure you get a

snug, leak-free connection.

COMPLETING THE SET UP

Compression (Assembled)

Nut (1/4")

(Assembled) Compression

_ Plastic Tubing

:'_:'_...... ! :' _ .... "' Molded

Ferrule_ i : end(Bulb)

(Not supplied) Compression nut

Copper tubing or Plastic tubing (B)

(Not supplied) (Not supplied)

Fitting

(Assembled)

(B) (1/4")(Not
supplied)

Household water supply line

1. Connect the household water line to the assembled
compression fitting.

= If you are using copper tubing, slip the compression

nut ( B ) (not supplied) and ferrule (not supplied) on

the copper tubing (not supplied) as shown.

= If you are using plastic tubing (B ), insert the

molded end (Bulb) of the plastic tubing ( B ) into the
compression fitting.

Z_ Do not use without the molded end (Bulb) of

CAUTIONthe plastic tubing ( B ).

2. Tighten the compression nut ( B ) onto the
compression fitting.

Do not over-tighten the compression nut ( B ).

3. Turn water on and check for any leakage. If you find
water drops or leakage inthe connection areas, turn
off the main water supply. Check the connections
and, if necessary, tighten.

Now that you have your new refrigerator installed in
place, you are ready to set up and enjoy the features

and functions of the appliance. By completing the
following steps, your refrigerator should be fully

operational.

1. Make sure your refrigerator is in an appropriate
location with reasonable clearance between it and

the wall. Refer to installation instructions in this

manual.

2. Once the refrigerator is plugged in, make sure the
interior light comes on when you open the doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to the
temperatures you want.

4. After you plug the refrigerator in, it will take a few
hours to reach the appropriate temperature. You
can store food and drinks in the refrigerator after

the temperature is sufficiently cool.

lf condensation or water drops appears on both

sides of fridge door's central part, turn the Energy
Saver mode off after removing the condensation.
(See the explanation on Energy Saver button in
the USING THE CONTROL PANEL.)

10 setting up

DA68-02488A-09.indb 10 13. 4. 25. 13132:08

©

ur French Door Refrgerator

USING THE CONTROL PANEL

RFG297**, RFG29P**

,c° oo I Water IceType _ I _ Water

@

@)

Touching this button turns Energy Saver
mode on and off. When you turn Energy
Saver on, the Energy Saver icon lights.
Turn Energy Saver off and the icon goes
off. The Energy Saver function automatically
turns on. when power is supplied to the
refrigerator.
If condensation or water drops appear on
the doors, turn the Energy Saver mode off.

Touch this button to set the freezer to your
desired temperature.
You can set the temperature between

-8°F and 8°F (between -22°C and -14°C).
Touch and hold this button for 3 seconds

to decrease the time needed to freeze
products in the Freezer. It can be helpful

if you need to quickly freeze easily spoiled
items or if the temperature in the freezer has
warmed dramatically (For example, if the
door was left open).

This button serves two purposes:

1) To turn the door open alarm on and off
Ifthe door alarm is set to On, an alarm
beeps if any refrigerator door is left open

for more than three minutes.
The beeping stops when you close the

door. The door alarm function is pre-
set to On in the factory. You can turn it

off by touching and then releasing this
button. You can turn it back on in the

same fashion. The icon lights up when the

function is on.
To reset the water filter life indicator.

2)

After you replace the water filter, touch

and hold this button for 3 seconds to reset

the water filter life indicator.

(Cubed)(Crushed)

W

Water

Touching this button turns on the Dispenser
LED lamp (under the display)in continuous
mode so that it stays on continuously.
The button also lights up. If you want the
Dispenser lamp to come on only when some
one uses the dispenser, touch this button

to turn the continuous mode off. Touch and
hold this button for 3 seconds to switch the

temperature units between °C and °R

Touch this button to set the fridge to your

desired temperature. You can set the

temperature between 34°F and 46°F

(between 7°C and 1°C).

Touch and hold this button for 3 seconds to

decrease the time needed to cool products
in the Refrigerator.
It can be helpful if you need to quickly cool
easily spoiled items or if the temperature
in the fridge has warmed dramatically (For
example, if the door was left open).

Ifyou don't want to make more ice, touch
this button. Also, pressing this button for 3

seconds turns on Child Lock which locks
the display panel and dispenser buttons so

the buttons can not be used. The Child Lock
icon lights up to indicate you've activated

the Child Lock function. Press 3 seconds to
unlock.

Touch this button to select your desired

ice type. Cubed and crushed ice modes
alternate when you press the button.

This mode can not be used with the Water

mode simultaneously.

Touch this button to dispense water. This

mode can not be used with the Ice Type
mode simultaneously. Water Water mode will

be off if you touch the Ice Type button.

DA68-02488A-09.indb 11 13. 4. 25. 13132:08

Cooling Off mode (also called Shop mode),
is designed for use by retailers when they
are displaying refrigerators on the shop
floor. In Cooling Off mode, the refrigerator's
fan motor and lights work normally, but the
compressors do not run, and the refrigerator
and freezer do not get cold.
Tostart Cooling Off mode, touch and hold
the Energy Saver button and the Power
Freeze button for 5 seconds during normal
operation. The refrigerator chime sounds and
the temperature display flashes OF OF.
Tocancel Cooling Off mode, touch and hold
the Energy Saver and the Power Freeze
buttons again for 5 seconds.

Ifyou don't want to make more ice, touch

the Ice Off button.
The icon will light up and the Ice-Maker

stops making ice.

We recommend you stop ice making

if the following occur:

- There is enough ice in the ice
bucket.

- You want to save water and energy.

- Water is not being supplied to the
refrigerator.

CHANGING THE WATER FILTER

Z_ To reduce risk of water damage to your

WARNING property DO NOT use generic brands of

water filters in your SAMSUNG Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTER.

SAMSUNG will not be legally responsible for any
damage, including, but not limited to property damage
caused by water leakage from use of a generic water
filter. SAMSUNG Refrigerators are designed to work

ONLY WITH SAMSUNG Water Filter.
The Filter light turns red to let you know when

it is time to change your water filter cartridge.

To give you time to get a new filter, the red

light comes on just before the capacity of the
current filter runs out. Changing the filter on
time provides you with the freshest, cleanest

water from your refrigerator.

1. Shut off the water supply. Then, turn the water filter
( 1 ) about 1/4 turn, counter-clockwise.

2. Pull the water filter ( 1 ) from the case filter ( 2 ).
,!I u

(Red)

lf the ice maker function is ON, and
the water Line is not connected, there

will be a water valve noise from the
back of the unit, press the Ice Off

(Hold 3sec for child lock) button for
less than 3 seconds until the Ice Off

Indicator (_) illuminates.

If you do not press any button(letters not ICON), the
display turns off in a few seconds.

If you press any button(letters not ICON), the
display lights up again.

The function key will operate after you remove
your finger from the letters except E.Saver, Ice

and Water key.

Water filter usage

This icon will light up when you need to
change the filter. After you use about 300
gallons of water, the filter indicator lights

up. (about 6 months). After you install the
new water filter, reset the filter indicator

by touching the Alarm/hold 3 sec for Filter
Reset button.

, If water is not dispensing or

dispensing slowly, you need to
replace the water filter because the
water filter is clogged.

• Some areas have large amounts of
lime in their water, which causes the
water filter to clog more quickly.

, o change the water filter more easily, shut off

the water supply valve.

,, Sometimes, it is hard to disassemble the water

filter because impurities in the water cause it to
stick. If you are having difficulties, grip the water
filter firmly and pull it hard.

,, When you pull the water

filter, a little water can
leak from the opening.

This is normal. To

minimize the water
leaks, keep the filter

cartridge horizontal when you pull it.

,, To prevent overflow, empty the water filter tray

( 3 ) and dry around the filter case ( 2 ).

3. Insert the new filter into the filter case ( 4 ).

4. Push the filter, and then turn it clockwise until it
locks.

, f you have trouble inserting the water filter

because of high water pressure, shut off the
water supply valve.

%
®

DA68-02488A-09.indb 12 13. 4. 25. DD 2:08

o The locked symbol should be lined up with the

indicator line.

_ F!l tt u

5. Touch the "Alarm/hold 3 see
for Filter Reset" button _

((Fi,,_/!=e,)for about 3 seconds to

reset the water filter. The color of
indicator ( _J ) changes from red

to blue, green, or yellow.

6. If you turned off the water supply, turn it back on.

minimum of 40 to 60 psi (276 to 414 kPa.)
If the water pressure to the reverse osmosis system is
less than 40 to 60 psi (276 to 414 kPa):

,, Check to see whether the sediment filter in the

reverse osmosis system is blocked. Replace the

filter if necessary.

,, Allow the storage tank on the reverse osmosis

system to refill after heavy usage.

,, If your refrigerator has a water filter, it may further

reduce the water pressure when used in conjunction
with a reverse osmosis system. Remove the water filter.

If you have questions about your water pressure, call
a licensed, qualified plumber.

CONTROLLING THE TEMPERATURE

For a replacement water filter, you can visit your

local home Improvement center or contact
the Samsung Parts distributor. Be sure the
replacement water filter has the SAMSUNG logo on

the box and on the water filter.
Link • http://www.samsungparts.com

Removing any residual matter inside the
water supply line after installing the water

filter.

1. Turn ON the main water supply and supply water

from water supply line.

2. Run water through the dispenser until the water

runs clear (approx. 6 to 7 minutes). This will clean
the water supply system and remove air from the

lines.

3. Additional flushing may be ...................................................................................................................................................

required in some households.

4. Open the Refrigerator door and

make sure there are no water

leaks coming from the water ........

tilter.

Be sure to flush the dispenser thoroughly,

otherwise water may drip from the dispenser.

This means that there is still air in the line.

Reverse Osmosis Water Supply IMPORTANT:

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve
of the refrigerator needs to be between 35 and 120
psi (241 and 827 kPa).

If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to be a

Basic temperature of Freezer and
Refrigerator Compartments

The basic temperature and recommended
temperatures of the Freezer and Refrigerator

Compartments are -2°F and 38°F (or -19°C and 3°C)
respectively. If the temperature of the Freezer and

Refrigerator Compartments are too high or low, adjust

the temperature manually.

Controlling the Freezer temperature

Recommend Temp (Freezer) : -2°F (or -19°0 )

The Freezer temperature can be set between -8°F

and 8°F (or between -22°C and -14°C) to suit your
particular needs. Press the Freezer button repeatedly
until the desired temperature is shown in the

temperature display. The temperature will change by

2°F (or 1°C) with each press. See below.
Fahrenheit : -2°F =-* -4°F =-*-6°F =-* -8°F =-* 8°F =-*6°F

=., 4OF .=, 2OF =., 0OF=., _2OF.
Centigrade : -19°C =-*-20°C =-* -21 °C =-* -22°C =-*

_14oc .=, _15oc _ -16oc =., _17oc =., _18oC =., _19oc.
Keep in mind that foods like some ice cream may melt

at 4°F (or -15.5°C). The temperature display will move
sequentially from -8°F to 8°F (or from -22°C to -14°C).

operatng 13

DA68-02488A-09.indb 13 13. 4. 25. 13132:08

Controlling the fridge temperature

The fridge temperature can be set between between
34°F and 46°F (or between 7°C and 1°C) to suit your

particular needs. Press the Fridge button repeatedly

until the desired temperature is shown in the
temperature display. The temperature will change by
2°F (or 1°C) with each press. See below.

Fahrenheit : 38°F -* 36°F _ 34°F _ 46°F _ 44°F
42°F _ 40°F _ 38°F.

Centigrade : 3°C _ 2°C _ 1°C _ 7°C _ 6°C _ 5°C

4°C -, 3°C.

The temperature control process for the Fridge works
just like the Freezer process. Press the Fridge button
to set your desired temperature. After a few seconds,
the Fridge will begin adjusting towards the newly set
temperature. This will be reflected in the digital display.

f ............................................................................................................................................................................................................................................................................................................................

Cubed Crushed Water IceOff

NO ICE

Select this ifyou want to

turn ice maker off

Using the ice Dispenser
Place a glass underneath the ice

dispenser and push gently against the
dispenser lever with your glass.
Make sure the glass is in line with

the dispenser to prevent the ice from

bouncing out.

Please wait 2 seconds before

CAUTIONremoving the glass under the

dispenser to prevent spills.

If the Refrigerator door opens, the Dispenser does not

work.

When Cubed Ice is selected after using the

CAUTION

Crushed Ice mode, a small amount of residual
crushed ice might be produced.

Recommend Temp (Fridge) : 38°F (or 3°0 )

- he temperature of the Freezer, Fridge or Pantry
Room may rise when you open the doors too

frequently, or if a large amount of warm or hot food
is placed inside.

- This may cause the digital display to blink. Once the
freezer and Fridge temperature return to their normal
set temperatures, the blinking will stop.

- Ifthe blinking continues, you may need to "reset"
the refrigerator. Try unplugging the appliance, wait
for around 10 minutes and then plug the power cord

back in.

- Ifthere is a communication error between the
Display and Main Controller, the Pantry Display light

may blink. If the blinking continues for a long period
of time, please contact a Samsung Electronics

Service Center.

USING THE COLD WATER
DISPENSER

Push the appropriate ice type button to

select what you want dispensed.

z_ Do not pull the lever out. You could damage

CAUTIONor break the lever's spring.

,, To clean the ice bin/

bucket, wash with a
mild detergent, rinse

well, and dry thoroughly
it. Do not use harsh or

abrasive cleaners or
solvents.

,, When you select Test button

Cubed Ice after using
the Crushed Ice mode,

a small amount of \
residual crushed ice might be produced.

o If ice doesn't come out, pull out the ice bucket and

press the test button located on the right side of ice
maker.

o Do not press the test button continuously when the

tray is filled with ice or water. Water may overflow or
ice may jam the bucket.

o Normal Use

To fill the ice bucket to maximum capacity after

installation, follow these steps:

1. Allow your refrigerator to operate and cool down
for 24 hours (or 1 full day).

- Waiting 24 hours will allow your ice maker to

cool properly.

DA68-02488A-09.indb 14 13. 4. 25. 13132:08

2. Dispense 4 to 6 ice cubes into the glass.

3. After 8, and then 16 hours, dispense a full glass of
ice.

• When you press the Test button you will hear the
refrigerator chime (ding-dong). When the chime

sounds, release the Test button.

• The chime sounds automatically again to let you
know the ice maker is working well.

If a power failure occurs, ice cubes may melt

CAUTIONthen freeze together when the power comes

back on, causing the dispenser to be out of
order.

To prevent this problem, after a power failure, pull out
the ice bucket and discard the residual ice or water.

- Close the water valve. Otherwise, water leakage may

OCCUr.

- Remove all food.

- Unplug the refrigerator.

- Wipe excess moisture from inside and leave
the doors open. Otherwise, odor and mold may

develop. Do not put your fingers, hands or any other
unsuitable objects in the chute or ice-maker bucket.

- It may result in personal injury or material damage.

Never put your finger or any other objects in the
dispenser opening.

- It may cause injury.

Do not try to disassemble the ice maker.
Do not wash or spray the ice bucket with water while

it is in the refrigerator. Remove it to clean it.

After you dump the ice from the ice bucket,

C_N yOUshould press the dispenser lever once

with the 'ICE CUBED' or 'CRUSHED' function

ON. The ice maker will make new ice faster after you
return the ice bucket to the freezer.

lf you use all the ice at once, you must repeat

Steps 2 and 3 on the previous page.
However, only wait 8 hours before dispensing the first
4 to 6 ice cubes. This will replenish the ice cubes and
ensure maximum ice production.

Using the ice off Function

When you select the

Ice Off mode, remove

all ice cubes from the
bucket. Ifyou are not

using the ice dispenser,
the ice cubes may
clump together. Pull the lock lever forward to remove
the bucket. Throw away the ice cubes or clumped ice.
Push the bucket back until you hear a click.

When you insert the Ice maker tray, be sure

CAUTION

that the tray is well centered at the entrance.

Otherwise, the tray may be stuck.

Water clouding phenomenon

AII water provided to the refrigerator flows through
the core filter which is an alkaline water

filter. In the filtering process, the pressure of the
water that has flowed out of the filter is increased,

and the water becomes saturated with oxygen and
nitrogen. When this water flows out into the air, the
pressure plummets and the oxygen and nitrogen get
supersaturated, which results in gas bubbles. The
water may temporarily look misty or cloudy due to
these oxygen bubbles. After a few seconds, the water

will look clear.

_ lease wait 1 second before removing the cup

after dispensing water to prevent spills.

Do not pull out the lever dispenser after dispensing
ice or water. It comes back automatically. Ice is made

in cubes. When you select "Crushed", the ice maker
grinds the ice cubes into crushed ice.

CAUTIONthe refrigerator. The water supply to this

Use only the ice maker provided with
refrigerator must only be installed/connected

by a suitably qualified person. Connect to a potable
water supply only.
To operate the ice maker properly, water pressure of

20 - 125 psi is required.

If you have a long vacation or business trip and won't

use the water or ice dispensers for a long time:

Operating 15

DA68-02488A-09.indb 15 13.4.25. Ill] 2:08

PARTS AND FEATURES

Use this page to become more familiar with the parts and features of the refrigerator.

Light

Interlocking switch

Door Closer

FF Ice-Maker

Foldable-Shelf

Slide-Shelf

Vertical Hinged

Section

Ji

Vegetable &

Fruit Drawers L"

Light

FZ Ice-Maker (on some model)

Ice Bucket Drawer

Tilting Pocket

Dairy

Compartment

Slide n-go shelf
(on some model)

Door Bins

Quick-Space
Glass Shelf

(on some models)

Cool Select
Pantry pLUs

Auto Pull Out

Freezer
Drawer Bin

When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid

®

scratching the other door.

If the Vertical Hinged Section is reversed, put it back to the right position and close the door.
Moisture may appear at times on the Vertical Hinged Section.

The door handle may become loose over time. If this happens, tighten the bolts found on the inside of
the door.

If you close one door with a lot of force, the other door may open.

When the door opens, the interlock switch automatically turns off the auger motor in the ice maker for
safety reasons.

When the interior or exterior LED lamp has gone out, please contact your service agents.

DA68-02488A-09.indb 16 13.4.25. Brq 2:08