Samsung RFG23UERS1-XEO Operating Instructions

Refrigerator
user manual
imagine the possibilities
Thank you for purchasing a Samsung product.
English
Free Standing Appliance
DA99-03403B-17.indb DA99-03403B-17.indb  2016. 3. 24.  10:012016. 3. 24.  10:01
Safety information
• Before operating the appliance, please read this manual thoroughly and retain it at a safe place near the appliance for your future reference.
• Use this appliance only for its intended purpose as described in this instruction manual. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your appliance.
• Because these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or fi nd help and information online at www.samsung.com.
2_ Safety information
DA99-03403B-17.indb 2DA99-03403B-17.indb 2 2016. 3. 24.  10:012016. 3. 24.  10:01
Important safety symbols and precautions :
Hazards or unsafe practices that may
WARNING
result in severe personal injury or death.
Hazards or unsafe practices that may
CAUTION
result in minor personal injury or property damage.
Do NOT attempt.
These warning signs are here to prevent injury to you and others. Please follow them carefully. After reading this section, keep it in a safe place for future reference.
SEVERE WARNING
WARNING
SIGNS FOR TRANSPORTATION AND SITE
Do NOT disassemble. Do NOT touch. Follow directions
carefully. Unplug the power
plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the contact center for help.
Note.
• When transporting and installing the appliance,care should be taken to ensure that no parts of the refrigerating circuit are damaged.
• R-600a or R-134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the refrigerator to see which refrigerant is used for your refrigerator.
• When this product contains fl ammable gas (Refrigerant R-600a),
- Refrigerant leaking from the pipe work could ignite or
Safety information _3
DA99-03403B-17.indb 3DA99-03403B-17.indb 3 2016. 3. 24.  10:012016. 3. 24.  10:01
cause an eye injury. If a leak is detected, avoid any naked fl ames or potential sources of ignition and air the room in which the appliance is standing for several minutes.
- In order to avoid the creation of a fl ammable gas-air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used.
- Never start up an appliance showing any signs of damage. If in doubt, consult your dealer. The room where the refrigerator will be sited must be 1m³ in size for every 8 g of R-600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identifi cation plate inside the appliance.
- If the appliance contains isobutane refrigerant (R-600a), a natural gas with high environmental compatibility that is, however, also combustible. When transporting and
4_ Safety information
installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged.
SEVERE WARNING
WARNING
SIGNS FOR INSTALLATION
• Do not install this appliance in a humid, oily or dusty location, in a location exposed to direct sunlight and water (rain drops).
- Deteriorated insulation of electrical parts may cause an electric shock or fi re.
• Do not place this refrigerator in direct sunlight or expose to the heat from stoves, room heaters or other appliances.
• Do not plug several appliances into the same multiple power board. The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matched the rating plate.
DA99-03403B-17.indb 4DA99-03403B-17.indb 4 2016. 3. 24.  10:012016. 3. 24.  10:01
- This provides the best performance and also prevents overloading house wiring circuits, which could cause a fi re hazard from overheated wires. If the wall socket is loose, do not insert the power plug.
- There is a risk of electric shock or fi re.
• Do not use a cord that shows cracks or abrasion damage along its length or at either end.
• Do not bend the power cord excessively or place heavy articles on it.
- Do not use aerosols near the refrigerator.
- Aerosols used near the refrigerator may cause an explosion or fi re.
• Do not install this appliance in a location where gas may leak.
- This may result in an electric shock or fi re.
• The installation or any service of this appliance is recommended by a qualifi ed technician or service company.
- Failing to do so may result
in an electric shock, fi re, explosion, problems with the product, or injury.
• This refrigerator must be properly installed and located in accordance with the manual before it is used.
• Connect the power plug in proper position with the cord hanging down.
- If you connect the power plug upside down, wire can get cut off and a cause fi re or an electric shock.
• Make sure that the power plug is not squashed or damaged by the back of the refrigerator.
• When moving the refrigerator, be careful not to roll over or damage the power cord.
- This constitutes a fi re hazard.
• The appliance must be positioned so that the plug is accessible after installation.
• The refrigerator must be grounded.
- You must ground the refrigerator to prevent any power leakages or electric shocks caused by current leakage from the refrigerator.
Safety information _5
DA99-03403B-17.indb 5DA99-03403B-17.indb 5 2016. 3. 24.  10:012016. 3. 24.  10:01
• Never use gas pipes, telephone lines or other potential lightening rods as ground.
- Improper use of the ground plug can result in an electric shock.
• If the power cord is damaged, have it replaced immediately by the manufacturer or its service agent.
• The fuse on the refrigerator must be changed by a qualifi ed technician or service company.
- Failing to do so may result in an electric shock or personal injury. Contact with a service center if any damage is found after removing the packing materials.
CAUTION SIGNS FOR
CAUTION
• Allow the appliance to stand
6_ Safety information
INSTALLATION
• Keep ventilation opening in the appliance enclosure or mounting structure clear of obstruction.
for 2 hours after installation.
WARNING
• Do not store articles on the
• Do not put items fi lled with
• Do not let children hang on
• Do not leave the doors of
• Do not allow babies or
• Do not sit on the Freezer
SIGNS FOR USING
• Do not insert the power plug with wet hands.
top of the appliance.
- When you open or close the door, the articles may fall and cause a personal injury and/or material damage.
water on the refrigerator.
- If spilled, there is a risk of fi re or electric shock.
the door.
- Failure to do so may cause serious personal injury.
the refrigerator open while the refrigerator is unattended and do not let children enter inside the refrigerator.
children go inside the drawer.
- It can cause death from suffocation by entrapment or personal injury.
door.
- The door may be broken and cause a personal injury.
SEVERE WARNING
DA99-03403B-17.indb 6DA99-03403B-17.indb 6 2016. 3. 24.  10:012016. 3. 24.  10:01
• To prevent children entrapment, you must reinstall the divider using provided screws after cleaning or other actions if you removed the divider from the drawer.
• Never put fi ngers or other objects into the dispenser hole.
- Failure to do so may cause personal injury or material damage.
• Do not store volatile or fl ammable substances such as benzene, thinner, alcohol, ether or LP gas in the refrigerator.
- The storage of any of such products may cause an explosion.
• Do not store low temperature-sensitive pharmaceutical products, scientifi c materials or other low temperature-sensitive products in the refrigerator.
- Products that require strict temperature controls must not be stored in the refrigerator.
• Do not place or use electrical appliance inside the refrigerator, unless they
are of a type recommended by the manufacturer.
• Do not use a hair dryer to dry the inside of the refrigerator. Do not place a lighted candle in the refrigerator for removing bad odors.
- This may result in an electric shock or fi re.
• Do not touch the inside walls of the freezer or products stored in the freezer with wet hands.
- This may cause frostbite.
• Do not use mechanical devices or any other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• This product is intended only for the storage of food in a domestic environment.
• Bottles should be stored tightly together so that they do not fall out.
• In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate
Safety information _7
DA99-03403B-17.indb 7DA99-03403B-17.indb 7 2016. 3. 24.  10:012016. 3. 24.  10:01
immediately without touching the power plug. Do not touch the appliance or power cord.
- Do not use a ventilating fan.
- A spark may result in an explosion or fi re.
• Use only the LED Lamps provided by manufacturer or service agent.
• Children should be supervised to ensure that they do not play with and/or climb into the appliance.
- Keep fingers out of "pinch point" areas; clearances between the doors and cabinet are necessarily small. Be careful when you open the doors when children are in the area.
• Do not disassemble or repair the refrigerator by yourself.
- You run a risk of causing a fi re, malfunction and/ or personal injury. In case of malfunction, please contact your service agent.
• If the appliance generates a strange noise, a burning or
8_ Safety information
smell or smoke, unplug the power plug immediately and contact your nearest service center.
- Failing to do so may result in an electric or fi re hazards.
• If you experience diffi culty when changing the light, contact service agent.
• If the products is equipped with the LED Lamp, do not disassemble the Lamp Cover and LED Lamp by yourself.
- Please contact your service agent.
• If any dust or water is in the refrigerator, pull out power plug and contact your Samsung Electronics service center.
- There is a risk of fi re.
CAUTION SIGNS FOR
CAUTION
USING
• To get best performance from the product,
- Do not place foods too closely in front of the vents at the rear of the appliance as it can obstruct free air
DA99-03403B-17.indb 8DA99-03403B-17.indb 8 2016. 3. 24.  10:012016. 3. 24.  10:01
circulation in the refrigerator compartment.
- Wrap the food up properly or place it in airtight containers before putting it into the refrigerator.
- Do not put any newly introduced food for freezing near to already existing food.
• Do not place carbonated or fi zzy drinks in the freezer compartment. Do not put bottles or glass containers in the freezer.
- When the contents freeze, the glass may break and cause personal injury and property damage.
• Do not change or modify the functionality of the refrigerator.
- Changes or modifi cations may result in a personal injury and/or property damage. Any changes or modifi cations performed by a 3rd party on this completed appliance are neither covered under Samsung warranty service, nor is Samsung responsible for safety issues and damages that result from 3rd party modifi cations.
• Do not block air holes.
- If the air holes are blocked, especially with a plastic bag, the refrigerator can be over cooled. If this cooling period lasts too long, the water fi lter may break and cause water leakage.
- Do not put any newly introduced food for freezing near to already existing food.
• Please observe maximum storage times and expiry dates of frozen goods.
• Fill the water tank, ice tray, water cubes only with potable water.
• Use only the ice-maker provided with the refrigerator.
• The water supply to this refrigerator must only be installed/connected by a suitably qualifi ed person and connected to a potable water supply only.
• In order to operate the ice-maker properly, water pressure of 138~862 kPa (1.4~8.8 kgf/cm
2
) is required.
• Do not spray volatile material such as insecticide onto the surface of the appliance.
Safety information _9
DA99-03403B-17.indb 9DA99-03403B-17.indb 9 2016. 3. 24.  10:012016. 3. 24.  10:01
- As well as being harmful to humans, it may also result in an electric shock, fi re or problems with the product.
• Do not apply strong shock or excessive force onto the surface of glass.
- Broken glass may result in a personal injury and/or property damage.
CAUTION SIGNS
CAUTION
FOR CLEANING AND MAINTENANCE
• Do not directly spray water inside or outside the refrigerator.
- There is a risk of fi re or electric shock.
• Do not use or place any substances sensitive to temperature such as infl ammable sprays, infl ammable objects, dry ice, medicine, or chemicals near the refrigerator. Do not keep volatile or infl ammable objects or substances (benzene, thinner, propane gas, etc.) in the refrigerator.
- This refrigerator is for storing food only.
10_ Safety information
- This may result in a fi re or an explosion.
• Do not spray cleaning products directly on the display.
- Printed letters on the display may come off.
• Remove any foreign matter or dust from the power plug pins. But do not use a wet or damp cloth when cleaning the plug, remove any foreign material or dust from the power plug pins.
- Otherwise there is a risk of fi re or electric shock.
• Never put fi ngers or other objects into the dispenser hole and ice chute.
- It may cause a personal injury or material damage.
• Unplug the refrigerator before cleaning and performing maintenance.
Clean by using a soft
WARNING
cloth with neutral detergent.
DA99-03403B-17.indb 10DA99-03403B-17.indb 10 2016. 3. 24.  10:012016. 3. 24.  10:01
CAUTION
SIGNS FOR DISPOSAL
• Ensure that none of the pipes on the back of the appliance are damaged prior to disposal.
• R-600a or R-134a is used as a refrigerant. Check the compressor label on the rear of the appliance or the rating label inside the refrigerator to see which refrigerant is used for your refrigerator. When this product contains fl ammable gas (Refrigerant R-600a), contact your local authority in regard to safe disposal of this product. Cyclopentane is used as an insulation blowing gas. The gases in insulation material require special disposal procedure. Please contact your local authorities in regard to the environmentally safe disposal of this product. Ensure that none of the pipes on the back of the appliances are damaged prior to disposal. The pipes shall be broken in the open space.
SEVERE WARNING
• When disposing of this product or other refrigerators, remove the door/door seals, door latch so that small children or animals cannot become trapped inside. Leave the shelves in place so that children may not easily climb inside. Children should be supervised to ensure that they do not play with the old appliance.
• Please dispose of the packaging material for this product in an environmentally friendly manner.
Safety information _11
DA99-03403B-17.indb 11DA99-03403B-17.indb 11 2016. 3. 24.  10:012016. 3. 24.  10:01
ADDITIONAL TIPS FOR PROPER USAGE
• In the event of a power failure, call the local offi ce of your Electricity Company and ask how long it is going to last.
- Most power failures that are corrected within an hour or two will not affect your refrigerator temperatures. However, you should minimize the number of door openings while the power is off.
- Should the power failure last more than 24 hours, remove all frozen food.
• If keys are provided with the refrigerator, the keys should be kept out of the reach of children and not be in the vicinity of the appliance.
• The appliance might not operate consistently (possibility of temperature becoming too warm in the refrigerator) when sited for an extended period of time below the cold end of the range of temperature for which the refrigerating appliance is designed.
• Do not store food which spoils easily at low temperature, such as bananas, melons.
• Your appliance is frost free, which means there is no need to manually defrost your appliance, as this will be carried out automatically.
• Temperature rise during defrosting can comply with ISO requirements. But if you want to prevent an undue rise in the temperature of the frozen food while defrosting the appliance, please wrap the frozen food up in several layers of newspaper.
• Any increase in temperature of frozen food during defrosting can shorten its storage life.
• There is no need to disconnect the refrigerator from the power supply if you will be away for less than three weeks. But, Remove all the food if you are going away for the three weeks or more. Unplug the refrigerator and clean it, rinse and dry.
12_ Safety information
DA99-03403B-17.indb 12DA99-03403B-17.indb 12 2016. 3. 24.  10:012016. 3. 24.  10:01
Saving Energy Tips
- Install the appliance in a cool, dry room with adequate ventilation. Ensure that it is not exposed to direct sunlight and never put it near a direct source of heat (radiator, for example).
- Never block any vents or grilles on the appliance.
- Allow warm food to cool down before placing it in the appliance.
- Put frozen food in the refrigerator to thaw. You can then use the low temperatures of the frozen products to cool food in the refrigerator.
- Do not keep the door of the appliance open for too long when putting food in or taking food out. The shorter time for which the door is open, the less ice will form in the freezer.
- Clean the rear of the refrigerator regularly. Dust increases energy consumption.
- Do not set temperature colder than necessary.
- Ensure suffi cient air exhaust
at the refrigerator base and at the back wall of the refrigerator. Do not cover air vent openings.
- Allow clearance to the right, left, back and top when installing. This will help reduce power consumption and keep your energy bills lower.
- For the most effi cient use of energy, please keep the all inner fi ttings such as baskets, drawers, shelves on the position supplied by manufacturer.
This appliance is intended to be used in household and similar applications such as
- staff kitchen areas in shops, offi ces and other working environments;
- farm houses and by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- catering and similar non­retail applications.
Safety information _13
DA99-03403B-17.indb 13DA99-03403B-17.indb 13 2016. 3. 24.  10:012016. 3. 24.  10:01
A
B
C
D
E
1578mm
335mm
125
°
125
°
50mm
908mm
605mm
1089mm
108mm
46mm
1103mm
Contents
SETTING UP YOUR REFRIGERATOR ······························································
OPERATING THE SAMSUNG REFRIGERATOR
TROUBLESHOOTING
·······················································································
··············································
Setting up your refrigerator
GETTING READY TO INSTALL THE REFRIGERATOR
Congratulations on your purchase of the Samsung Refrigerator. We hope you enjoy the state-of-art features and effi ciencies that this new appliance offers.
Selecting the best location for the Refrigerator
• A location with easy access to the water supply.
• A location without direct exposure to sunlight.
• A location with level (or nearly level) fl ooring.
• A location with enough space for the Refrigerator doors to open easily.
• Allow suffi cient space to the right, left, back and top for air circulation. If the Refrigerator does not have enough space, the internal cooling system may not work properly.
• Please ensure that appliance can be moved freely in the event of maintenance & service.
• Do not install the Refrigerator where the
temperature will go below 50 ºF (10 ºC).
B
A
E
C
D
Model RFG23U*
Depth “A” 712mm
Width “B” 908mm
Height “C” 1740mm
Overall Height “D” 1774mm
Depth “E” 774mm
50mm
°
108mm
46mm
125
°
335mm
1089mm
1103mm
125
1578mm
908mm
605mm
Each measurement based on the design dimension, so it may differ depending on the measuring method.
14
20
27
14_ Setting up
DA99-03403B-17.indb 14DA99-03403B-17.indb 14 2016. 3. 24.  10:012016. 3. 24.  10:01
When moving your refrigerator
3
To prevent fl oor damage be sure the front leveling legs are in the up position (above the fl oor). Refer to ‘ADJUSTING THE DOORS’ in the manual (at page 17)
FLOORING
For proper installation, this refrigerator must be placed on a level surface of hard material that is the same height as the rest of the fl ooring. This surface should be strong enough to support a fully loaded refrigerator. To protect the fi nish of the fl ooring, cut a large section of the cardboard carton and place under the refrigerator where you are working. When moving, be sure to pull the unit straight out and push back in straight.
REMOVING THE REFRIGERATOR DOORS
If the Refrigerator is too large to pass through your doorway easily, you can remove the refrigerator doors.
Disconnect power to the refrigerator
WARNING
• Be careful not to get injured while removing the
• Reattach the door/drawer properly to avoid:
- Moisture from air leakage.
- Uneven door alignment.
- Wasting energy due to improper door seal.
before removing the door or drawer.
• Be careful not to drop, damage or scratch the door/drawer while removing them.
door/drawer.
Tools you will need(Not provided)
Philips
screwdriver
Pliers
Flat-blade
screwdriver
Allen wrench
(3/16”) (5 mm)
Wrench(10 mm)
Disassemble the Refrigerator doors
1. With the door opened, remove the Hinge Cover cap 1 with a Flat head screwdriver, and close the door. Remove the 3 screws holding down the Hinge Cover and remove the Hinge Cover
2
.
2
1
2. Disconnect two connectors of the top cap, the one connector 7 on right side door and the other connector 4 on left side door. Remove the tube 5 with pressing the dark gray color part 6 of the water line coupler.
3
4
5
6
3
at each side
7
02 OPERATING01 SETTING UP
3
Setting up _15
DA99-03403B-17.indb 15DA99-03403B-17.indb 15 2016. 3. 24.  10:012016. 3. 24.  10:01
3.
Center of Transparent
coupler
The Guide Lines
Dispenser
Type A
Type B
Slot
Remove the 3 hex head bolts 7 attached to the upper left and right door hinges with a wrench (10 mm). With a Philips head screwdriver, remove the ground screw 8 attached to the upper left and right door hinges. Remove the upper left and right door hinges
8
7
9
9
.
DISASSEMBLE THE FREEZER DRAWER
1. Push the upper drawer in completely.
2. Remove the tilting pocket
brackets 2 upward at the same time.
1
by pulling on both
4. Lift the door straight up to remove.
5. With a Philips head screwdriver, remove the
10
two screws
attached to the lower left and right door hinges. With an wrench (5 mm), remove the two hex head bolts 11 attached to the lower left and right door hinges. Remove the lower left and right door hinges 12 .
12
10
11
REATTACHING THE REFRIGERATOR DOORS
To reattach the fridge doors, assemble parts in reverse order.
1. The Water Line must be fully inserted to the center of transparent coupler (Type A) or the Guide Lines (Type B) to prevent water leakage from the dispenser.
1
2
3. Take out the lower basket
3
by lifting the
basket up from rail system.
3
4.
Remove four 10 mm hex-head bolts from both sides.
5. Lift the freezer door up from the rails.
Type A
Center of Transparent
coupler
16_ Setting up
DA99-03403B-17.indb 16DA99-03403B-17.indb 16 2016. 3. 24.  10:022016. 3. 24.  10:02
Type B
Dispenser
The Guide Lines
Putting too much food into the freezer drawers can prevent the freezer from closing
CAUTION
completely and can cause frost build-up.
ASSEMBLE THE FREEZER DRAWER
flat-blade
screwdriver(-)
Control Lever
Adjustment part
Adjustment part
(3)
(1)
(3)
(2)
(4)
To reattach the freezer drawer, assemble parts in reverse order.
ADJUSTING THE DOORS
Now that the doors are back on the Refrigerator, you want to make sure the Refrigerator is level so that you can make fi nal adjustments. If the Refrigerator is not level, it will not be possible to get the doors perfectly even.
Insert a fl at-blade screwdriver (-) into a notch on the left control lever, and turn it count clockwise to level the refrigerator. (You turn the lever clockwise to lower the refrigerator and counterclockwise to raise it.)
1. If you open the drawer 1 , you can see the lower hinge
2. Insert a philips screwdriver (+)
4
of the lower hinge.
2
.
3
into the shaft
3. Adjust the height by turning a philips screwdriver (+) 3 clockwise ( ) or counterclockwise ( ).
(2)
(4)
(1)
(3)
When you turn a philips screwdriver (+) counterclockwise (
), the door will move
up.
02 OPERATING01 SETTING UP
(3)
screwdriver(-)
CAUTION
flat-blade
Control Lever
Both control levers must be touching the fl oor to avoid possible personal injury or property damage because of tipping.
If the right side is lower, perform the same procedure, but with the right control lever.
MAKING MINOR ADJUSTMENTS BETWEEN DOORS
Remember a level Refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on leveling the Refrigerator.
When the left door is lower than the right door.
When the left door is higher than the right door.
Adjustment part
Adjustment part
ADJUSTING THE FREEZER DRAWER LEVEL
Adjustment part
Freezer Drawer
Setting up _17
DA99-03403B-17.indb 17DA99-03403B-17.indb 17 2016. 3. 24.  10:022016. 3. 24.  10:02
1. Locate the height-adjuster 1 in the freezer drawer.
Unscrew the four Phillips screws
2
slightly to
loosen the door.
2
1
2. Loosen the controller screw
3
with a Phillips
screwdriver.
3
3. Find the best level to align the door slope.
Example) The slope is about 2 mm (0.08 inch) as shown
below.
Slope
ice-maker to operate properly, a water pressure of 138~862 kPa is required. Under normal conditions, a 170 cc (5.75 oz.) cup can be fi lled in 10 seconds. If the Refrigerator is installed in an area with low water pressure (below 138 kPa), you can install a booster pump to compensate for the low pressure. Make sure the water storage tank inside the Refrigerator is properly fi lled. To do this, press the water dispenser lever until the water runs from the water outlet.
Water line installation kits are available at extra cost from your dealer. We recommend using a water supply kit that contains copper tubing.
The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
Check the accessory list below.
Water fi lter Compression fi tting
Compression nut
Connecting to the water supply line
1. First, shut off the main water supply line and turn the ice-maker off.
2. Locate the nearest cold water drinking line.
3. After connecting the water supply with water fi lter, turn on water supply and Flush 3 L through fi lter before use (fl ush approximately 6 minutes).
1
Reference
plane
- Rotate the Height Adjuster to -2.0 to reduce the door slope.
Cold water line
2
Pipe clamp
Water line
3
installation kit
After adjustment, fi rst tighten screw 3 and then
2
screw
.
4
Shut off valve
CHECKING THE WATER LINE
A water dispenser is one of the helpful features on your new Samsung Refrigerator. To help promote better health, the Samsung water fi lter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. In order for the
18_ Setting up
DA99-03403B-17.indb 18DA99-03403B-17.indb 18 2016. 3. 24.  10:022016. 3. 24.  10:02
INSTALLING THE WATER LINE
Connecting the water line to the Refrigerator.
There are several items that you need to purchase to complete this connection. You may fi nd these items sold as a kit at your local hardware store.
Refrigerator
6.35 mm compression nut • copper tubing
• plastic tubing • ferrule
Refrigerator
Compression nut
Plastic tubing
(6.35 mm) (Supplied)
Compression fitting (Supplied)
Bulb
Compression nut (6.35 mm) (Not supplied)
Plastic tubing
(Supplied)
Ferrule
(Not supplied)
Copper tubing
(Not supplied) (Not supplied)
or
Household water line
1. Slip the compression nut through the supplied plastic tubing
2. Tighten the compression nut compression fi tting.
If you are using copper tubing, slip the compression
-
nut
.
onto the 6.35 mm
(not included) and ferrule (not included) on
copper tubing (not included) as shown.
- If you are using plastic tubing , insert the
molded end(Bulb) of the plastic tubing
into the
compression fi tting.
Do not use without the molded end(Bulb) of the
plastic tubing
3. Tighten the compression nut
.
onto the compression fi tting. Do not over-tighten the compression nut
.
4. Turn water on and check for any leakage.
Only connect the water line to a drinkable water
source. If you have to repair or disassemble the water line, cut off 6.35 mm of the plastic tubing to make sure you get a snug, leak-free connection.
2 3
Sticker (month indicator)
4. Remove the fi lter cap and insert the fi lter into the fi lter housing.
5. Slowly turn the water fi lter 90º clockwise to align with the printing mark on the cover, locking the fi lter in position.
Make sure to align the water fi lter label mark
with center of cover fi lter printing as illustrated. Remember, do not overtighten.
4 5
Separation of red cap.
Cover fi lter
Turn until the label is aligned.
You should remove the right side upper glass shelf before installing the water fi lter.
1
02 OPERATING01 SETTING UP
Installing the water fi lter.
1. Remove the water fi lter cover 1 .
2. Remove the fi xed cap by turning it counter clockwise. Keep the cap in a safe place for later use if you don’t use the fi lter.
3. Remove the water fi lter from the box and put
a replacement indicator sticker on the fi lter as shown. Place the sticker on the fi lter that dates six months in the future. For example, if you install the water fi lter in March, put the “SEP” sticker on the fi lter to remind you to replace it in September. That way you’ll know when it is time to replace the fi lter. Normally, a fi lter life is about 6 months.
Removing any residual matter inside the water supply line after installing the water fi lter.
1. Turn ON the main water supply & turn OFF the valve to the water supply line.
2. Run water through the dispenser until the water runs clear (approx. 6-7 minutes). This will clean the water supply system and remove air from the lines.
3. Additional fl ushing may be required in some households.
4. Open the Refrigerator door and make sure there are no water leaks coming from the water fi lter.
Be sure to fl ush the dispenser thoroughly or water may leak from it. This is due to the fact
that there is still air in the line.
Setting up _19
DA99-03403B-17.indb 19DA99-03403B-17.indb 19 2016. 3. 24.  10:022016. 3. 24.  10:02
Operating the SAMSUNG refrigerator
USING THE CONTROL PANEL
1
2
3
87
1
Energy
Saver
Button
2
Freezer / Power
Freeze (3sec) Button
3
Alarm
/ Reset
Filter (3sec) Button
20_ Operating
For better energy effi ciency, press the Energy Saver button ( If condensation occurs on the doors, turn the Energy Saver function off.
Press the Freezer / Power Freeze (3sec) button ( to your desired temperature. You can set the temperature between
-14 ºC and -22 ºC. Press and hold the Freezer / Power Freeze (3sec) button for 3 seconds, to speed up the time needed to freeze products in the Freezer. It can be helpful if you need to quickly freeze easily spoiled items or if the temperature in the Freezer has warmed dramatically (For example, if the door was left open). When you use this function the energy consumption of the refrigerator will increase. Remember to turn it off when you don’t need it and return the freezer to your original temperature setting. When you have enough ice, just press and hold the button for 3 seconds again to cancel the Power Freeze mode. Power Freeze mode must be activated before putting large stuff in freezer compartment at least 20 hours before.
Press the Alarm button ( ) to turn off the door open alarm. After removing the old water fi lter and installing a new one, reset the Indicator by pressing and holing the “Alarm” button for 3 seconds. The indicator will light again in about 6months to let you know it is Time to change your water fi lter.
).
) to set the Freezer
3
Alarm
4
5
6
/ Reset
Filter (3sec) Button
4
Lighting
Button
5
Fridge /
Power
Cool
(3sec)
Button
6
Ice Off /
Child Lock
(3sec)
7
Ice Button
8
Water
Button
Some functions are activated after a few-
second delay when the buttons are pressed, while others operate immediately. This is normal operation.
The fi lter Indicator will be Blue when you initially insert the water fi lter. The fi lter Indicator will be Light Pink when you have used your water fi lter for 5 months. The fi lter Indicator ( will be Red when you have used your water fi lter for 6 months.
Press the Lighting button ( ) to turn on the dispenser LED lamp.
Press the Fridge / Power Cool (3sec) button ( desired temperature. You can set the temperature between 1 ºC and 7 ºC. Press and hold the Fridge / Power Cool (3sec) button for 3 seconds, to speed up the time needed to cool products in the Refrigerator. It can be helpful if you need to quickly cool easily spoiled items or if the temperature in the fridge has warmed dramatically if the door was left open). Press and hold the button for 3 seconds again to cancel the Power Cool mode.
Press the Ice Off button ( ) to turn the ice making function off. If you press and hold the Ice Off button for 3 seconds, the display and dispenser will be locked.
Press the Ice button to select your desired ice type. Cubed and crushed ice modes will be alternatively changed whenever you press the button. After selecting, push the dispenser Lever gently with your glass. This mode can not be used with the Water mode simultaneously.
Press the Water button to dispense water. There is no Off mode additionally. After selecting, push the dispenser Lever gently with your glass. This button can not be used with the Ice button simultaneously. Water mode will be off if you press the Ice button.
) to set the fridge to your
)
(For example,
DA99-03403B-17.indb 20DA99-03403B-17.indb 20 2016. 3. 24.  10:022016. 3. 24.  10:02
USING THE CONTROL PANEL
Basic temperature of Freezer and Refrigerator Compartments
The basic temperature and/or recommended temperature of Freezer and Refrigerator Compartments are -19 °C and 3 °C respectively. If the temperature of Freezer and Refrigerator Compartments are too high or low, adjust the temperature manually.
Controlling the Freezer temperature
The Freezer temperature can be set between
-14 ºC and -22 ºC to suit your particular needs. Press the Freezer button repeatedly until the desired temperature is shown in the temperature display. Keep in mind that foods like ice cream may melt at -15 ºC. The temperature display will move sequentially from -22 ºC to -14 ºC. When the display reaches -14 ºC, it will begin again at -22 ºC.
Controlling the Refrigerator temperature
The Refrigerator temperature can be set between 7 ºC and 1 ºC to suit your particular needs. Press the Fridge button repeatedly until the desired temperature is shown in the temperature display. The temperature control process for the Fridge works just like the Freezer process. Press the Fridge button to set your desired temperature. After a few seconds, the Fridge will begin adjusting towards the newly set temperature. This will be refl ected in the digital display.
- The temperature of the Freezer, Refrigerator or pantry room may rise when
you open the doors too frequently, or if a large
amount of warm or hot food is placed inside.
- This may cause the digital display to blink. Once the Freezer and Refrigerator temperature return to their normal set temperatures, the blinking will stop.
- If the blinking continues, you may need to “reset” the Refrigerator. Try unplugging the appliance, wait for around 10 minutes and then plug the power cord back in.
- The temperature of the pantry room may be a little different according to the location inside.
- If communication between display and Main Controller errors, Pantry display light may blink. Once the pantry room return to their normal set temperatures, the blinking will stop. If the blinking continues for a long period of time, please contact to Samsung Electronics Service Center.
USING THE COLD WATER DISPENSER
Press the Ice / Water button to select the type of you want.
No ICE
Select this if you want to turn ice-maker off.
• Place a glass underneath the ice dispenser and push gently against the dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the ice from bouncing out.
• Please wait 2 seconds before removing the glass under the dispenser to prevent spills. If the Refrigerator door opens, the dispenser does not work.
• When Cubed Ice is selected after using the Crushed Ice feature, a small amount of residual crushed ice might be produced.
• Water Dispenser Installation
After installation, press the dispenser arm for at
least 2 minutes to remove trapped air from the water line and to fi ll the water system.
PUSH
• In case ice doesn’t come out, pull out the ice
bucket and press test button located on the right side of ice-maker.
• Do not press the test button continuously when
the tray is fi lled with ice or water as illustration. Water may overfl ow or ice jamming may occur.
• Normal Use
To fi ll ice bucket to maximum capacity after
installation, make sure to do the following steps.
1. Allow your refrigerator to operate and cool
down for 24 hours (or 1 full day).
2. Waiting 24 hours will allow your ice maker to
cool properly.
3. Dispense 4 to 6 ice cubes into the glass.
4. After 8 and 16 hours, dispense a full glass of
ice at each time.
02 OPERATING
Operating _21
DA99-03403B-17.indb 21DA99-03403B-17.indb 21 2016. 3. 24.  10:022016. 3. 24.  10:02
Test button
Check the water level
2
Whenever all ice is used at one time, the
above step 3 and 4 must be repeated (before dispense the fi rst 4 to 6 ice cubes, it needs waiting 8 hours). This will replenish the ice cubes and ensure maximum ice production.
When you dump the ice from the ice bucket, you should press the dispenser lever once with ‘ICE CUBED’ or ‘CRUSHED’ function ON to get new ice faster after replacing the ice bucket in the refrigerator.
Using the water dispenser
Place a glass underneath the water outlet and push gently against the water dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the water from splashing out. If you have just installed the refrigerator or installed a new water fi lter,Flush 3 L through fi lter before use (fl ush approximately 6 minutes). Make sure that water fl ows clearly again before drinking.
When you do not use the water dispenser
for 2~3 days (especially during the summer), the dispensed water may have a funny smell or taste. If this occurs, we recommend that you discard the fi rst 1~2 glasses for better tasting water.
Using the ice off function
When selecting the Ice Off mode, remove all ice cubes from the bucket. If you are not using the ice dispenser,
Pull on
Push
the ice cubes may clump together. Pull the lock lever forward to throw away ice cubes or remove clumped ice from the bucket. Push the bucket back until you hear a click.
If you have a long vacation or business trip,
close the water valve and shut off the water supply to the Refrigerator. This will help prevent accidental leakages. Do not disassemble the Ice-maker personally. It may cause disorder. Do not wash or spray the ice bucket with water. Just wipe it with a dry cloth. In order to operate the ice-maker properly, water pressure of 138~862 kPa is required.
Water clouding phenomenon
All water provided to refrigerators fl ows through the core fi lter which is an alkaline water fi lter. In this process, the pressure in the water that has fl owed out of the fi lter gets increased, and oxygen and nitrogen become saturated. When this water fl ows out in the air, the pressure plummets and the oxygen and nitrogen get supersaturated so that they turn into gas bubbles. The water could look misty due to these oxygen bubbles.The water may look temporarily cloudy due to these oxygen bubbles. After a few seconds, the water will look clear. Please wait 1 second before removing the cup after dispensing water to prevent spills. Do not pull out the lever dispenser after taking out ice or water. It comes back automatically. Ice is made in cubes. When you select “Crushed”, the ice-maker grinds the ice cubes into crushed ice.
22_ Operating
DA99-03403B-17.indb 22DA99-03403B-17.indb 22 2016. 3. 24.  10:022016. 3. 24.  10:02
PARTS AND FEATURES
(1)
(2)
(3)
(4)
(5)
(11)
(12)
(13)
(10)
(7)
(9)
(6)
(8)
Light
Water Filter
Door Closer
Light
Use this page to become more familiar with the parts and features of the Refrigerator.
Light
(1)
(11)
(3)
(5)
(2)
(10)
(13)
(4)
Water Filter
(6)
(7)
(12)
Door Closer
(8)
(9)
Light
USING THE COOL SELECT PANTRY™
The Cool Select Pantry™ is a full-width drawer with adjustable temperature control. This pantry can be used for large party trays, deli items, pizza, beverages or miscellaneous items. There is a temperature control which can adjust the amount of cold air allowed into the pantry. The control is located on the right side of the pantry.
• Press the Temp button repeatedly until your
desired mode is lit. The Fresh mode (3 °C), Zero Zone mode (0 °C) and Deli mode (5 °C) will be selected whenever you press the Temp button. Initially, the Fresh mode is set. Though the setting temperature is different from the current temperature, the temperature will be changed to the setting temperature automatically.
Temp
You can select your Pantry temperature from among Deli (5 °C [41 °F]), Fresh (3 °C [38 °F] ) and Zero Zone (0 °C [32 °F] ) modes.
02 OPERATING
( 1 ) Ice-Maker ( 2 ) Foldable-Shelf ( 3 ) Slide-Shelf ( 4 ) Vertical Hinged Section ( 5 ) Vegetable & Fruit Drawers ( 6 ) Slide-Shelf ( 7 ) 2 Step Foldable Shelf ( 8 ) Dairy Compartment
( 9 ) Door Bins ( 10 ) Cool Select Pantry™ ( 11 )
Tilting Pocket
( 12 ) Auto Pull Out Drawer ( 13 ) Freezer Drawer Bin
Selection Button
1. When “Deli” is selected, the temperature of the pantry will be kept around 5 °C (41 °F). This feature helps keep food fresh for a long time.
2. When “Fresh” is selected, the temperature of the pantry will be kept around 3 °C (38 °F). This feature helps keep food fresh for a longer time.
3. When “Zero Zone” is selected, the temperature of the pantry will be kept around 0 °C (32 °F). This feature also helps keep meat or fi sh fresh for a longer time.
Operating _23
DA99-03403B-17.indb 23DA99-03403B-17.indb 23 2016. 3. 24.  10:022016. 3. 24.  10:02
Deli Fresh Zero Zone
• pineapple
• lemon
• avocado
• potato
• cucumbers
• apples
• oranges
• grapes
• zucchinis
• corn
• steaks
• hard cheeses
• cold cuts
• bacon
• hot dogs
Fruits and vegetables may be damaged under the “Zero Zone” setting. Do not store lettuce or other leafy produce in this pantry.
Do not store glass bottles in this pantry. If they are frozen, they can break and
CAUTION
cause personal injury.
REMOVING THE REFRIGERATOR ACCESSORIES
2. Tempered Glass shelves
To remove - Tilt up the front of the shelf in the
direction shown
Pull the shelf out.
To relocate - Tilt the front of the shelf up and
guide the shelf hooks into the slots at a
desired height. Then lower the front of the shelf so that the hooks can drop into the slots.
The Tempered Glass shelves are heavy. Use special care when removing them.
CAUTION
2
1
and lift it up vertically 2 .
1
1. Door Bins & Dairy Compartment
To remove -
To relocate - Slide it in above the desired
CAUTION
Sharp corners of the bins may cause injury.
Do not adjust a bin full of foods.
Dust removal method - Remove the guard and
wash in water.
Simply lift the bin up and pull straight out.
location and push down until it stops.
Injury may occur if the door bins are not fi rmly assembled. Do not allow children to play with bins.
3. Vegetable & Fruit Drawers
To remove - Pull the drawer out to full
extension. Tilt up the front of the drawer and pull straight out.
To relocate - Insert the drawer into the frame rails and push back into place.
The drawers need to be removed before the
glass shelf above them can be lifted out. Do not open the drawers while the pantry is open. It may cause a scratch or breakage to the drawer covers.
24_ Operating
DA99-03403B-17.indb 24DA99-03403B-17.indb 24 2016. 3. 24.  10:022016. 3. 24.  10:02
4. Cool Select Pantry™
To remove the pantry - Pull the pantry out to
full extension. Tilt up the front side of pantry
and pull straight out.
To relocate the pantry - Push the rails to the back of the Refrigerator. Place the drawer onto the rails and slide the pantry back until it is in
place.
REMOVING THE FREEZER ACCESSORIES
1. Tilting Pocket
To remove - Pull the brackets upward until you hear a clicking sound and remove the pocket
To replace - Hook the ends of the pocket into both brackets
into place.
1
and push down until it locks
1
02 OPERATING
To remove the divider - Pull the pantry completely out to full extension and raise the
front side of the divider to unhook it from the rear wall of the pantry, then lift the divider out.
To relocate the divider - Hook the back of the divider over the rear wall of the pantry and
push the divider down.
USING THE DOORS
The Refrigerator doors ensure that the doors close all the way and are securely sealed. When the Refrigerator door is only partially open, it will automatically close. The door will stay open when opened more than 76mm.
USING THE TILTING POCKET
The Tilting Pocket can be used to store up to a 406mm pizza if you place it as shown in the illustration.
2. Auto Pull out Drawer
To remove - Pull the drawer out to full
extension. Tilt up rear of drawer and lift straight out.
To relocate - Place the drawer onto the rails by tilting it up. Lower the drawer into place until it is horizontal and slide the drawer in.
2
1
3. Freezer Drawer
To remove the freezer drawer - Pull the freezer drawer out fully. Tilt up the rear of the bin and lift it out to remove.
To relocate the freezer drawer - Place the bin into the rail assembly.
You can scratch the side of the bin if you twist it left or right when disassembling
CAUTION
or re-assembling it. Do not allow babies or children go inside
the freezer drawer.
CAUTION
seriously injure themselves. Do not sit on the freezer door. The door may break. Do not allow children to climb into the freezer drawer.
They could damage the refrigerator and
Do not remove the divider.
WARNING
Operating _25
DA99-03403B-17.indb 25DA99-03403B-17.indb 25 2016. 3. 24.  10:022016. 3. 24.  10:02
If trapped inside, children may become injury and suffocate to death.
WARNING
CLEANING THE REFRIGERATOR
Do not use benzene, thinner, or Clorox, Chloride for cleaning. They may damage
WARNING
cause a fi re. Do not spray the refrigerator with water while it is
plugged in, as it may cause an electric shock. Do not clean the refrigerator with benzene, thinner or car detergent for risk of fi re.
the surface of the appliance and may
CHANGING THE INTERIOR LIGHTS
Do not disassemble or replace the LED type Lighting. To change the LED Type
CAUTION
or your authorized Samsung dealer.
Lighting contact Samsung service center
If Users randomly exchange the LED lamp by yourself, this may result in an electric shock or personal injury.
CHANGING THE WATER FILTER
To reduce risk of water damage to your property DO NOT use generic brands
CAUTION
of water fi lters in your SAMSUNG
USE ONLY SAMSUNG BRAND WATER FILTERS. SAMSUNG will not be legally responsible for any damage, including, but not limited to property damage caused by water leakage from use of a generic water fi lter. SAMSUNG Refrigerators are designed to work ONLY WITH SAMSUNG WATER Filter.
The “Filter Indicator” light lets you know when it is time to change your water fi lter cartridge. To give you preparation time to get a new fi lter, the red light will come on just before the capacity of the current fi lter runs out. Changing the fi lter on time provides you with the freshest, cleanest water from your fridge.
1. Take a new water fi lter and put a month
2. Remove the new fi lter’s protective cap and
3. Position and insert the new fi lter into the fi lter
4. Once you have completed this process, press
5. Lastly, Flush 3L through fi lter before use (fl ush
dispenser. This means that there is still air in the line. Do NOT use the water or ice dispenser without a water fi lter cartridge because the water line may become blocked.
Refrigerator.
indicator sticker on the fi lter as shown. The date on the sticker must be six months from the current date. For example, if you are replacing the water fi lter in March, put the “SEP” (September) sticker on the fi lter to remind you to replace in September. Normal fi lter life is about every 6 months.
remove the old fi lter.
housing. Slowly turn the water fi lter clockwise to align with the printing mark on the cover, locking the fi lter in position. Make sure to align the water fi lter label mark with the center of cover fi lter printing as illustrated. Remember, do not over-tighten.
and hold the Alarm button for 3 seconds to reset the fi lter schedule.
approximately 6 minutes) Make sure that water fl ows clearly again before drinking.
Be sure to fl ush the dispenser thoroughly otherwise water may drip from the
26_ Operating
DA99-03403B-17.indb 26DA99-03403B-17.indb 26 2016. 3. 24.  10:022016. 3. 24.  10:02
Troubleshooting
PROBLEM SOLUTION
The Refrigerator does not work at
all or it does not chill suffi ciently.
The food in the Refrigerator is frozen.
You hear unusual noise or sounds.
The front corners and vertical hinged section of the appliance are hot and condensation is occurring.
Ice-maker is not producing ice.
You can hear water bubbling in the Refrigerator.
There is a bad smell in the Refrigerator.
Frost forms on the walls of the Freezer.
Water dispenser is not functioning.
• Check that the power plug is properly connected.
• Is the temperature control on the display panel set to the correct temperature?
Try setting it to a lower temperature.
• Is the Refrigerator in direct sunlight or located near a heat source?
• Is the back of the Refrigerator too close to the wall and therefore keeping air from circulating?
• Is the temperature control on the display set to the correct temperature?
Try setting it to a warmer temperature.
• Is the temperature in the room too low?
• Did you store the food with high water content in the coldest part of the Refrigerator? Try moving those items into the body of the Refrigerator instead of keeping them in the Cool Select Pantry™.
• Check that the Refrigerator is level and stable.
• Is the back of the Refrigerator too close to the wall and therefore keeping air from circulating?
• Was anything dropped behind or under the Refrigerator?
• A “ticking” sound is heard from inside the Refrigerator. It is normal and occurs because various accessories are contracting or expanding according to the temperature of the Refrigerator interior.
• Some heat is normal as anti-condensators are installed in the vertical hinged section of the Refrigerator to prevent condensation.
• Is the Refrigerator door ajar? Condensation can occur when you leave the door open for a long time.
• Did you wait for 12 hours after installation of the water supply line before making ice?
• Is the water line connected and the shut-off valve opened?
• Did you manually stop the ice making function?
• Is the Freezer temperature too warm? Try setting the Freezer temperature lower.
• This is normal. The bubbling comes from the Refrigerator coolant liquid circulating through the Refrigerator.
• Check for spoiled food.
• Foods with strong odors(for example, fi sh) should be tightly covered.
• Clean out your Freezer periodically and throw away any spoiled or suspicious food.
• Is the air vent blocked? Remove any obstructions so air can circulate freely.
• Allow suffi cient space between the foods stored for effi cient air circulation.
• Is the Freezer drawer closed properly?
• Is the water line connected and the shut-off valve opened?
• Has the water supply line tubing been crushed or kinked?
Make sure the tubing is free and clear of any obstruction.
• Is the water tank frozen because the Refrigerator temperature is too low?
Try selecting a warmer setting on the main display panel.
03 TROUBLESHOOTING
Troubleshooting _27
DA99-03403B-17.indb 27DA99-03403B-17.indb 27 2016. 3. 24.  10:022016. 3. 24.  10:02
Memo
DA99-03403B-17.indb 28DA99-03403B-17.indb 28 2016. 3. 24.  10:022016. 3. 24.  10:02
Memo
DA99-03403B-17.indb 29DA99-03403B-17.indb 29 2016. 3. 24.  10:022016. 3. 24.  10:02
Ambient Room Temperature Limits
This refrigerator is designed to operate in ambient temperatures specified by its temperature class marked on the rating plate.
Class Symbol
Extended Temperate SN +10 to +32 +10 to +32
Temperate N +16 to +32 +16 to +32
Subtropical ST +16 to +38 +18 to +38
Tropical T +16 to +43 +18 to +43
IEC 62552 (ISO 15502) ISO 8561
Ambient Temperature range (°C)
Internal temperatures may be affected by such factors as the location of the fridge/freezer, ambient temperature and the frequency with which you open the door. Adjust the temperature as required to compensate for these factors.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
English
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government offi ce, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
DA99-03403B-17.indb 30DA99-03403B-17.indb 30 2016. 3. 24.  10:022016. 3. 24.  10:02
Loading...
+ 230 hidden pages