Samsung RF32FMQDBXW-AA User Manual [en, es, fr]

English

Refrigerator

user manual

Free Standing Appliance

imagine the possibilities

Thank you for purchasing this Samsung product.

DA68-02918A-05.indb 1 14. 6. 25. �� 10:57

safety information

SAFETY INFORMATION

• Before operating the appliance, please read
this manual thoroughly and retain it for your
reference.

• Use this appliance only for its intended purpose,
as described in this instruction manual.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory, or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning the use of the appliance by a
person responsible for their safety.

• Warnings and Important Safety Instructions in
this manual do not cover all possible conditions
and situations that may occur.
It is your responsibility to use common sense,
caution, and care when installing, maintaining,
and operating your appliance.

• Because the following operating instructions
cover various models, the characteristics of
your refrigerator may differ slightly from those
described in this manual.

• Never start up an appliance showing any signs
of damage. If in doubt, consult your dealer.

• Refrigerant squirting out of the pipes could
ignite or cause an eye injury. If refrigerant
leaks from the pipe, avoid any naked flames
and move anything flammable away from the
product and ventilate the room immediately.

- Failing to do so may result in fire or explosion.

Important safety symbols and
precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall
socket.

Make sure the machine is grounded to
prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent injury
to you and others.
Please follow them carefully.
After reading this section, keep it in a safe
place for future reference.

02_ safety information

DA68-02918A-05.indb 2 14. 6. 25. �� 10:57

WARNING

CRITICAL TRANSPORTATION AND
SITE WARNINGS

• When transporting and installing the
appliance,care should be taken to
ensure that no parts of the refrigerating
circuit are damaged.

- Refrigerant leaking from the pipe work could
ignite or cause an eye injury. If a leak is
detected, avoid any naked flames or potential
sources of ignition and air the room in which the
appliance is standing for several minutes.

- When transporting and installing the appliance,
care should be taken to ensure that no parts of
the refrigerating circuit are damaged.

WARNING

CRITICAL INSTALLATION WARNINGS

• Deteriorated insulation on electrical
parts may cause an electric shock or
fire.

• Do not place this refrigerator in direct sunlight or
expose it to the heat from stoves, room heaters
or other appliance.

• Do not plug several appliances into the same
multiple power strip.
The refrigerator should always be plugged into
its own individual electrical outlet which has a
voltage rating that matches the rating plate.

- This provides the best performance and
also prevents overloading house wiring
circuits, which could cause a fire hazard from
overheated wires.

• If the wall socket is loose, do not insert the
power plug.

- There is a risk of electric shock or fire.

• Do not use a cord that shows cracks or
abrasion damage along its length or at either
end.

• Do not pull the power cord or bend it excessively.

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal
object, place a heavy object on the power
cord, insert the power cord between objects, or
push the power cord into the space behind the
appliance.

- When moving the refrigerator, be careful not to
roll over or damage the power cord.

- This may result in an electric shock or fire.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause
an explosion or fire.

- Do not bend the power cord excessively or
place heavy articles on it.

• This refrigerator must be properly
installed and located in accordance
with the manual before it is used.

• Do not install the refrigerator in a damp place or
place where it may come in contact with water.

- Deteriorated insulation of electrical parts may
cause an electric shock or fire.

• Connect the power plug in proper position with
the cord hanging down.

- If you connect the power plug upside down,
wire can get cut off and a cause fire or an
electric shock.

• Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.

• When moving the refrigerator, be careful not to
roll over or damage the power cord.

- This constitutes a fire hazard.

• Keep the packing materials out of reach of
children.

- There is a risk of death from suffocation if a
child puts the packaging material on his or her
head.

• The appliance must be positioned so that the
plug is accessible after installation.

- Failing to do so may result in an electric shock
or fire due to electric leakage.

• Do not install this appliance near a heater or
inflammable material.

• Do not install this appliance in a humid, oily or
dusty location, or in a location exposed to direct
sunlight or water (rain drops).

• Do not install this appliance in a location where
gas may leak.

- This may result in an electric shock or fire.

• If any dust or water inundates the refrigerator,
pull out the power plug and contact your
Samsung Electronics service.

- Otherwise there is a risk of fire.

• Do not stand on top of the appliance or place
objects (such as laundry, lighted candles,
lighted cigarettes, dishes, chemicals, metal
objects, etc.) on the appliance.

- This may result in an electric shock, fire,
problems with the product, or injury.

• This appliance must be properly

safety information _03

DA68-02918A-05.indb 3 14. 6. 25. �� 10:57

• Do not ground the appliance to a gas pipe,

grounded.

plastic water pipe, telephone line, or other
potential lightning attractor.

- You must ground the refrigerator to prevent any
power leakages or electric shocks caused by
current leakage from the refrigerator.

- Improper grounding can result in an electric
shock, fire, explosion, or problems with the
product.

- Never plug the power cord into a socket that is
not grounded correctly. Make sure the socket is
grounded in accordance with local and national
codes.

- Improper use of the grounding plug can result
in a risk of electric shock.

• If it is necessary to use an extension cord, use
only a 3-wire extension cord that has a 3-blade
grounding plug and a 3-slot receptacle that will
accept the plug on the appliance. The extension
cord should be rated at AC115-120 V, 10 A, or
more. If a grounding adapter is used, make sure
the receptacle box is fully grounded.

• Plug the power plug into the wall socket firmly.

• Do not use a damaged power plug, damaged
power cord or loose wall socket.

- This may result in an electric shock or fire.

• If the power cord is damaged,
have it replaced immediately by the
manufacturer or its service agent.

• The fuse on the refrigerator must only be
changed by a qualified technician or service
company.

- Failing to do so may result in an electric shock
or personal injury.

CAUTION

INSTALLATION CAUTIONS

• Keep ventilation opening in the
appliance enclosure or mounting
structure clear of obstruction.

• Allow the appliance to stand for 2 hours after
installation.

• We strongly recommend you use a qualified
technician or service company to install or
service the refrigerator.

- Failing to do so may result in an electric shock,
fire, explosion, problems with the product, or
injury.

04_ safety information

WARNING

CRITICAL USAGE WARNINGS

• Do not touch the power plug with wet
hands.

- This may result in an electric shock.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles
may fall and cause a personal injury and/or
material damage.

• Do not put items filled with water on the
refrigerator.

- If spilled, there is a risk of fire or electric shock.

• Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.

- This may cause frostbite.

• Do not use or place any substances sensitive
to temperature such as inflammable sprays,
inflammable objects, dry ice, medicine, or
chemicals near the refrigerator.

• Do not keep volatile or inflammable objects or
substances (benzene, thinner, propane gas,
alcohol, ether, LP gas and other such products
etc.) in the refrigerator.

- This refrigerator is for storing food only.

- This may result in a fire or an explosion.

• Do not store pharmaceuticals products,
scientifiic materials or temperature-sensitive
products in the refrigerator.

- Products that require strict temperature controls
must not be stored in the refrigerator.

• Do not place or use electrical appliance inside
the refrigerator/freezer, unless they are of a type
recommended by the manufacturer.

• If the refrigerator emits a burning smell or
smoke, unplug the refrigerator immediately
and contact your Samsung Electronics service
center.

• If dust or water inundates the refrigerator, pull
out the power plug and contact your Samsung
Electronics service.

- Otherwise there is a risk of fire.

• If a gas leak is detected, avoid any naked
flames or potential sources of ignition and air
the room in which the appliance is standing for
several minutes.

• Do not use mechanical devices or any other
means to accelerate the defrosting process,
other than those recommended by the
manufacturer.

• Do not damage the refrigerant circuit.

• Do not spray volatile material such as

DA68-02918A-05.indb 4 14. 6. 25. �� 10:57

insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may also
result in an electric shock, fire or problems with
the product.

• Do not use a hair dryer to dry the inside of the
refrigerator. Do not place a lighted candle in the
refrigerator to remove bad odors.

- This may result in an electric shock or fire.

• Fill the water tank and ice tray with potable
water only.

- Do not fill with tea, soda, or sports drinks.
This can damage of refrigerator.

• Do not let children hang on the door.
Serious injury can occur.

- Risk of child entrapment.
Do not let children go inside the refrigerator.

• Do not leave the doors of the refrigerator open
while the refrigerator is unattended and do not
let children go inside the refrigerator.

• Do not allow babies or children go inside the
drawer.

- It can cause death from suffocation by
entrapment or personal injury.

• Do not sit on the Freezer door.

- The door can be broken and cause personal
injury.

• To prevent children from getting trapped in the
refrigerator you must reinstall the divider using
the provided screws after cleaning or other
actions if you removed the divider from the
drawer.

• In the event of a gas leak (such as
propane gas, LP gas, etc.), ventilate
immediately without touching the
power plug. Do not touch the appliance
or power cord.

- Do not use a ventilating fan.

- A spark may result in an explosion or fire.

• Use only the LED Lamps provided by the
manufacturer or service agent.

• Children should be supervised to ensure that
they do not play with the appliance.

• Keep fingers out of “pinch point” areas;
clearances between the doors and cabinet are
necessarily small.

• Do not let children hang on the door.
Serious injury can occur.

• Risk of child entrapment.
Do not let children go inside the refrigerator.

• Bottles should be stored tightly together so that
they do not fall out.

• This product is intended for the storage of food
in a domestic environment only.

• Never put your fingers or other objects into the
dispenser hole, ice chute, or ice maker bucket.

- It may cause a personal injury or material
damage.

• Do not insert hands, feet, or metal objects (such
as knives, etc.) into the bottom or the back of
the refrigerator.

- This may result in an electric shock or injury.

- Any sharp edges may cause a personal injury.

• Do not attempt to repair, disassemble,
or modify the appliance yourself.

- Do not use any fuse (such as copper, steel wire,
etc.) other than the standard fuse.

- If the appliance needs to be serviced or re­installed, contact your nearest Samsung service
center.

- Failing to do so may result in an electric shock,
fire, problems with the product, or injury.

• If the appliance generates a strange
noise, a burning smell, or smoke,
unplug the power plug immediately and
contact your nearest service center.

- Failing to do so may result in an electric or fire
hazards.

• Pull the power plug out of the socket before
changing the interior lamps in the refrigerator

- Otherwise, there is a risk of electric shock.

• If you experience difficulty when changing a light,
contact your nearest Samsung service center.

• If the products is equipped with LED Lamps,
do not disassemble the Lamp Cover and LED
Lamp by yourself.

- Please contact your service agent.

• Plug the power plug into the wall socket firmly.
Do not use a damaged power plug, damaged
power cord, or loose wall socket.

- This may result in an electric shock or fire.

• Do not put a container filled with water on the
appliance.

- If spilled, there is a risk of fire or electric shock.

• Never stare directly at the UV LED lamp for long
periods of time.

- This may result in eye strain due to the
ultraviolet rays.

safety information _05

DA68-02918A-05.indb 5 14. 6. 25. �� 10:57

CAUTION

USAGE CAUTIONS

• Allow the appliance to stand for 2 hours
after installation.

• To get best performance from the product:

- Do not place foods too close to the vents at
the rear of the appliance. It can obstruct free air
circulation in the refrigerator compartment.

- Wrap food up properly or place it in airtight
containers before putting it into the refrigerator.

- Do not put food you have just put into the
freezer near already frozen food.

• Do not place glass or bottles or carbonated
beverages into the freezer.

- The container may freeze and break, and this
may result in injury.

• Please observe maximum storage times and
the expiration dates of frozen goods.

• There is no need to disconnect the refrigerator
from the power supply if you will be away for
less than three weeks. However, if you will be
away for more than three weeks, remove all the
food, unplug the refrigerator, close the water
valve, wipe excess moisture from the inside
walls, and leave the doors open to prevent
odors and mold.

• Do not place carbonated or fizzy drinks in the
freezer compartment.
Do not put bottles or glass containers in the
freezer.

- When the contents freeze, the glass may
break and cause personal injury and property
damage.

• Do not change or modify the functionality of the
refrigerator.

- Changes or modifications may result in personal
injury and/or property damage.
Any changes or modifications performed by
a 3rd party on this completed appliance are
not covered under Samsung warranty service.
Samsung is not responsible for any safety
problems, injuries, or damage resulting from 3rd
party modifications.

• Do not block the air holes.

- If the air holes are blocked, especially with a
plastic bag, the refrigerator can be over cooled.
If this cooling period lasts too long, the water
filter may break and cause water leakage.

• Use only the ice-maker provided with the
refrigerator.

• The water supply to this refrigerator must be

06_ safety information

installed/connected by a suitably qualified
person and connected to a potable water
supply only.

• If you won’t be using the refrigerator for a very
long period of time, (3 weeks or more) empty
the refrigerator, unplug it, close the water valve,
wipe excess moisture from the inside walls,
and leave the doors open to prevent odors and
mold.

• If the refrigerator is flooded or a large amount
of water enters the mechanical or electrical
sections of the refrigerator, pull out the power
plug and contact your Samsung Electronics
service center.

CAUTION

CLEANING AND MAINTENANCE
CAUTIONS

• Do not spray cleaning products directly
on the display.

- Printed letters on the display may come off.

• If any foreign substance such as water enters
the mechanical or electrical sections of the
refrigerator while you are cleaning it, unplug the
power plug and contact your nearest service
center.

- Failing to do so may result in an electric shock
or fire.

• Remove all foreign substances such as dust
or water from the power plug terminals and
contact points using a dry cloth on a regular
basis.

- Unplug the power plug and clean it with a dry
cloth.

- Failing to do so may result in an electric shock
or fire.

• Do not clean the appliance by spraying water
directly onto it.

• Do not use benzene, thinner, or Clorox to clean
the refrigerator.

- They may damage the surface of the appliance
and may cause a fire.

• Do not spray inflammable gas near the
refrigerator.

- There is a risk of explosion or fire.

• Before cleaning or performing
maintenance, unplug the appliance
from the wall socket.

- Failing to do so may result in an electric shock
or fire.

DA68-02918A-05.indb 6 14. 6. 25. �� 10:57

WARNING

• This product contains chemicals known to
the State of California to cause cancer and
reproductive toxicity.

WARNING

CRITICAL DISPOSAL WARNINGS

• DANGER : Risk of child entrapment.
Before you throw away your old
refrigerator or freezer:

- Take off the doors and door latch.

- Leave the shelves in place so that children
cannot easily climb inside.

• Ensure that none of the pipes on the back of
the appliance are damaged or broken prior to
disposal.

• Cyclopentane is used in the insulation of
this refrigerator. Consequently, the insulation
material in the refrigerator requires special
disposal procedures. Please contact your local
authorities regarding the environmentally safe
disposal of this product.

• When disposing of this or any other refrigerator,
remove the door/door seals and door latch
so that children or animals cannot become
trapped inside. Children should be supervised
to ensure that they do not play with or enter the
appliance.

- If trapped inside, a child may get hurt or
suffocate to death.

• Please dispose of the packaging material for
this product in an environmentally friendly
manner.

• Keep all packaging materials well out of the
reach of children, as packaging materials can
be dangerous to children.

- If a child places a bag over his or her head, the
child could suffocate.

ADDITIONAL TIPS FOR
PROPER USAGE

• In the event of a power failure, call the local
office of your Electricity Company and ask how
long it is going to last.

- Most power failures that are corrected within
an hour or two will not affect your refrigerator
temperatures.
However, you should minimize the number of
door openings while the power is off.
If the power failure lasts more than 24 hours,
remove all frozen food.

• If keys are provided with the refrigerator, the
keys should be kept out of the reach of children
and not be in the vicinity of the appliance.

• The appliance might not operate consistently
(frozen contents can thaw or temperatures
can become too warm in the frozen food
compartment) when sited for an extended
period of time in a location where ambient
air temperatures are constantly below the
temperatures for which the appliance is
designed.

• Do not store food which goes bad easily at low
temperatures, such as bananas and melons.

• Your appliance is frost free, which means there
is no need to manually defrost your appliance,
This will be carried out automatically.

• Temperature rise during defrosting complies
with ISO requirements. But, If you want to
prevent an undue rise in the temperature of the
frozen food while the appliance defrosts, wrap
the frozen food in several layers of newspaper.

• Any increase in temperature of frozen food
during defrosting can shorten its storage life.

• Do not re-freeze frozen foods that have thawed
completely.

safety information _07

DA68-02918A-05.indb 7 14. 6. 25. �� 10:57

Saving Energy Tips

- Install the appliance in a cool, dry room with
adequate ventilation.
Ensure that it is not exposed to direct sunlight
and never put it near a direct source of heat
(radiator, for example).

- Never block any vents or grilles on the
appliance.

- Allow warm food to cool down before placing it
in the appliance.

- Put frozen food in the refrigerator to thaw.
You can then use the low temperatures of the
frozen products to cool food in the refrigerator.

- Do not keep the door of the appliance open for
too long when putting food in or taking food
out. The shorter the time the door is open, the
less ice will form in the freezer.

- Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and
keep your energy bills lower.

contents

SETTING UP YOUR REFRIGERATOR …………………………………… 09
OPERATING YOUR SAMSUNG REFRIGERATOR …………………… 16
TROUBLESHOOTING ……………………………………………………… 25

08_ safety information

DA68-02918A-05.indb 8 14. 6. 25. �� 10:57

setting up your refrigerator

GETTING READY TO INSTALL THE
REFRIGERATOR

Congratulations on your purchase of the Samsung
refrigerator. We hope you enjoy the state-of-art

features and efficiencies that this new appliance
offers.

Selecting the best location for the
Refrigerator
Choose :

• A location with easy access to the water supply.

• A location without direct exposure to sunlight.

• A location with level (or nearly level) flooring.

• A location with enough space for the refrigerator
doors to open easily.

• A location that allows sufficient space to the
right, left, back, and top for air circulation. If the
refrigerator does not have enough space, the
internal cooling system may not work properly.

• A location that allows you to move the
refrigerator easily if it needs maintenance or
service.

• Do not install the refrigerator in locations where
the temperature is over 109 °F (43 °C) or below
41 °F (5 °C ).

2"

(50mm)

°

125

59 6/8" (1519mm)

35 3/4" (908mm)

2 6/8" (72.3mm)

1 3/4" (43mm)

30 7/8"

(785mm)

Each measurement based on the design
dimension, so it may differ depending on the

measuring method.

When moving your refrigerator

125

°

12"

(305.5mm)

49 5/8" (1260mm)

01 SETTING UP

B

B

AA

To prevent floor damage, be sure the front leveling
legs are in the up position (above the floor).
Refer to “HOW TO LEVEL THE REFRIGERATOR”
in the manual on page 13.

EE

D

C

C

D

FLOORING

For proper installation, you must place this
refrigerator on a level, hard surface that is the same
height as the rest of the floor.
This surface should be strong enough to support a
fully loaded refrigerator.

Depth “A” 35 ¾” (908 mm)

Width “B” 35 ¾” (908 mm)

Height “C” 71 ¾” (1822 mm)

Overall Height “D” 72 7/8” (1850 mm)

DA68-02918A-05.indb 9 14. 6. 25. �� 10:57

To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working.
When moving the refrigerator, you need to pull and
push it straight forwards or back. Do not wiggle it
from side to side.

setting up _09

REMOVING THE REFRIGERATOR
DOORS

If the refrigerator is too large to pass through your
doorway easily, you can remove the refrigerator
doors.

A

2. Separate the two connectors on the left door

and the one connector on the right door. If there
are red clips on the water tube, remove them
now. Press the white sleeve [D] of the Water
Tube Coupler, and then separate the Water
Tube [E].

- Not all models have red clips.

Tools you will need (Not provided)

Philips screwdriver

(+)

Pliers

Disconnect power to the refrigerator before

WARNING

removing the doors or drawers.

• Be careful not to drop, damage or
scratch the doors/drawers while
removing them.

• Use care when you remove the doors/drawers.
The doors are heavy and you could injure
yourself.

• Re-attach the doors/drawers properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

Flat-blade

screwdriver (-)

Allen wrench
5/32" (4mm)

Socket wrench

3/8'' (10mm)

Allen wrench

7/32'' (5mm)

DISASSEMBLE THE
REFRIGERATOR DOORS

1. With the door closed, remove the 3 screws
holding the Top Cover (A) with a Phillips (+)
Screwdriver, and then remove the Top Cover
with the entire wire-harnesses attached.

E

Red Clip
(6.35 mm)

E

D

3. Pull up the Fixer Lever (B), and then pull it

forward.

B

B

4. Remove the Hinge (C).

C

5. Lift up the Fridge Door and take it off.

• While disassembling and reassembling

CAUTION

the door, make sure that the electric
wires are not peeled off.

• Do not let the door fall down.

D

10_ setting up

DA68-02918A-05.indb 10 14. 6. 25. �� 10:57

DISASSEMBLE THE FREEZER
DOORS

• Be sure to remove the Fridge Door

CAUTION

1. With the door open, remove the screw holding

before removing the Freezer Door.

• Be careful with the wires attached to
the bottom of the Freezer Door while
disassembling.

the cover (A) of the Adjustable Leg at the
bottom of the door with a Phillips (+)
Screwdriver, and then disassemble the
Connector (B).

A

B

RE-ATTACHING THE
REFRIGERATOR DOORS

• Be sure to re-attach the Freezer Door

CAUTION

How to Re-attach the Freezer Door

1. Insert the door into the lower hinge (A) in the

before re-attaching the Fridge Door.

• Before re-attaching, make sure that all
the wire connectors at the bottom of the
Freezer Door are connected.

direction of (1) and then push the door in the
direction of (2). Take care not to scratch the
door with the Mid-Hinge (B).

01 SETTING UP

2. Lift up and remove the Mid Hinge Cap (C) on
the Door Hinge above the Freezer Door.

C

3. While pushing the door in the direction of the

arrow, lift up the Mid Hinge Shaft (D).

D

4. Being careful that the door does not touch the

Mid Hinge (E), tilt the Door forward a little, and
then lift it up to remove.

1

B

A

2

1

• Be careful not to damage the wires on

CAUTION

the bottom of the door. Avoid stepping
on them, etc.

2. Insert the Hinge Shaft (C) into the Mid Hinge
Hole (D) and put on the Hinge Cap (E).

When assembling the Hinge Shaft and the
Hinge Cap, be sure to assemble them in
the correct direction.

C

D

E

3. With the door open, join the connectors on the

bottom of the door.

E

2

- Be careful not to step on or damage the
connectors.

setting up _11

DA68-02918A-05.indb 11 14. 6. 25. �� 10:57

4. Attach the Adjustable Leg Cover using a Phillips
(+) Screwdriver.

5. Connect the Water Tube [E]. If the model has
red clips, attach them now to the Coupler [F].
Connect the connector [G] on the left door and
the connector [H] on the right door.

G

Red Clip

E

(6.35mm)

H

How to Assemble Fridge Door

1. Attach the detached Fridge Door to the Mid
Hinge.

2. Slide the Fridge Hinge (C) into the fixing slot,
and then press it down so that it is aligned with
the hole in the door.

C

3. Inserting the Fixer Lever (B) in the direction of

the arrow, and then flip it down to assemble.

B

B

F

6. Attach the front of the Top Cover, and then

press down on its back until it lies flat. Re­attach the screws.

• Assemble the Fridge and Freezer doors

CAUTION

in the reverse order of disassembly.

• If the Wire Connectors are cross­assembled, the display will not work
properly.

• Clips are located inside the cap on the
top.

• To prevent water leaks, if the refrigerator
uses red clips, make sure the red clips
are properly connected to the Coupler
after you insert the Water Tube [E] into
the center of the Coupler.

E

clip A
(6.35 mm)

Center of the
Indicator Line

4. Assemble the Wire Connector.

12_ setting up

DA68-02918A-05.indb 12 14. 6. 25. �� 10:57

LEVELING THE REFRIGERATOR
AND ADJUSTING HEIGHT AND
GAP OF THE DOORS

HOW TO LEVEL THE REFRIGERATOR

If the Refrigerator is put on a floor that is not level,
it can cause a height difference between the doors.

• Insert a Flat-Head (-) Screwdriver into the slot in
the Leveling Leg Control Lever and adjust the
level by turning the Control Lever clockwise or
counter-clockwise. When you rotate the Lever
clockwise, you raise the refrigerator. When you
rotate the Lever counter-clockwise, you lower
the refrigerator.

flat-blade
screwdriver(-)

• If the Refrigerator is not level back and
front, put a solid panel (such as a plastic
panel, a plastic ruler, etc.) on the floor
where the rear legs will rest, and then fix
it in place with plastic tape. When you
push in the Refrigerator, make sure the
rear legs rest on the panel.

• If you have a wooden floor or similar soft
floor, take care not to damage the floor
when pushing the Refrigerator into place.

Control Lever

HOW TO ADJUST THE DOOR
HEIGHT

If any one of the doors is lower than
the other:

• Check if the Refrigerator is level
before adjusting the door.

• Adjust the door height difference
by inserting a Snap Ring ( 1 ) as
shown between the door and the
hinge. You can use the rings on the right side
door of the fresh food compartment and both
sides of the freezer compartment.

1

• After checking the height difference, select one
Snap Ring with a suitable thickness. Insert one
Snap Ring only, Inserting two or more Snap
Rings may cause the Snap Rings to slip out or
make a rubbing noise.

• Lift up the lower door and insert the Snap
Ring into the space between the Door and the
Hinge.

• To avoid injury, insert or remove Snap

CAUTION

Rings carefully.

• Keep the Snap Rings out of the reach of
children and make sure that children do
not play with them or put them into their
mouths.

• 1 mm, 1.5 mm, 2 mm, and 2.5 mm Snap
Rings come with the Refrigerator.

• If the Refrigerator is level before you
load it with food, the Refrigerator may
become unbalanced due to the weight
of the food. If this occurs, adjust the level
again using the same procedure.

• If you raise the door too far, it can rub
against the Top Cover.

01 SETTING UP

Snap Rings included with the refrigerator:

1 mm 1.5 mm 2 mm 2.5 mm

setting up _13

DA68-02918A-05.indb 13 14. 6. 25. �� 10:57

HOW TO ADJUST THE DOOR GAP

If the gap between the left and right fridge
compartment doors is not even.

• You can adjust the gap by turning
the bolt at the top right of the cold
storage compartment door.

• Do not turn the bolt too far.
You can break it.

• Water line installation kits are available at
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper
tubing and ¼” compression nut.

Connecting to the water supply line

1. First, shut off the main water
supply.

1. With the doors closed, remove the 3 screws
holding the top cover using a Phillips
screwdriver, and then lift it off together with the
connected cables.

2. Turn the bolt with a 4 mm
hexagonal L-wrench to adjust
the gap. (Not provided)

3. Turn the bolt clockwise to
( ) widen the gap.
Turn the bolt counter clockwise ( ) to narrow
the gap.

INSTALLING THE WATER
DISPENSER LINE

A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.

The water line also connects to the ice maker.
For the ice maker to operate properly, water

pressure of 20~125 psi (138~862 kPa) is required.
If the refrigerator is installed in an area with low

water pressure (below 20 psi), you can install a
booster pump to compensate for the low pressure.

After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly filled. To do this, press the water dispenser
lever until the water runs from the water outlet.

2. Locate the nearest cold water drinking line and
install the pipe clamp and shut off valve.

Cold water line

Pipe clamp

Shut off valve

3. Connect the water line installation kit to the shut

off valve.

Cold water line

Pipe clamp

Shut off valve

Water line installation kit

Connecting the water supply line to the
refrigerator.

There are several items that you need to purchase
to complete this connection.

You may find these items sold as a kit at your local
hardware store.

For Copper Tubing For Plastic Tubing

• ¼” copper tubing

• ¼” compression nut (1pc)

• Ferrule (2pc)

• ¼” plastic tubing
Molded end(Bulb)

→

• ¼” compression nut (1pc)

14_ setting up

DA68-02918A-05.indb 14 14. 6. 25. �� 10:57

Refrigerator

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Copper tubing
(Not supplied)

or

Household water supply line

Plastic Tubing
(Assembled)

Compression
Fitting
(Assembled)

Molded
end(Bulb)

Compression
nut (B) (1/4”)
(Not supplied)

Plastic tubing (B)
(Not supplied)

1. Connect the household water line to the
assembled compression fitting.

- If you are using copper tubing, slip the
compression nut ( B ) (not supplied) and
ferrule (not supplied) on the copper tubing (not
supplied) as shown.

- If you are using plastic tubing ( B ), insert the
molded end (Bulb) of the plastic tubing ( B ) into
the compression fitting.

• Do not use without the molded end (Bulb)

CAUTION

of the plastic tubing ( B ).

2. Tighten the compression nut ( B ) onto the

compression fitting.
Do not over-tighten the compression nut ( B ) .

3. Turn water on and check for any leakage. If you
find water drops or leakage in the connection
areas, turn off the main water supply. Check
the connections and, if necessary, tighten.

4. Flush 1 gallon of water through the filter before
drinking or using the water from the refrigerator.
(Flush approximately 6 minutes.) To flush, press
a large glass or cup against the water dispenser
lever. Fill the glass, empty it into the kitchen sink
after it is filled, and then repeat.

5. After you turn on the refrigerator, let the ice
maker make ice for 1 to 2 days. Over that period
of time, throw out the first 1 or 2 buckets of ice
the freezer makes to ensure all impurities have
been removed from the water line.

cut off 1/4“ of the plastic tubing to make sure you
get a snug, leak-free connection.

• You can test the water line quickly using
a paper cup. Under normal conditions,
the water dispenser can fill a 5.75 oz.
(170cc) cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.

1. Make sure your refrigerator is in an appropriate
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.

2. Once the refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.

3. Set the Temperature control to the coldest
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.

4. After you plug the refrigerator in, it will take a
few hours to reach the appropriate temperature.
You can store food and drinks in the refrigerator
after the temperature is sufficiently cool.

If condensation or water drops appears
on both sides of fridge door’s central
part, turn the Energy Saver mode off after
removing the condensation.
(See the explanation on Energy Saver
button in the USING THE CONTROL
PANEL.)

01 SETTING UP

• Only connect the water line to a drinkable
water source.

If you have to repair or disassemble the water line,

setting up _15

DA68-02918A-05.indb 15 14. 6. 25. �� 10:57

operating your samsung
refrigerator

USING THE CONTROL PANEL

1

2

3

9

7

( 1 ) CoolSelect+ (Cool Select Room)

The CoolSelect button lets you set the Cool
Select Room on the bottom right of your
refrigerator to one of four settings: Freezer, Soft
Freezing, Chill, or Cool.
Press the CoolSelect button for three seconds to
activate the Cool Select Room function, and then
select one of the four settings.

Select Freezer to set the Cool Select

Freezer

Soft

Freezing

Chill

Cool

Room to the same temperature as
the freezer.

• Use this setting to keep frozen
food fresh.

• Select Soft Freezing to set the
temperature in the Cool Select
Room to 23 °F (-5 °C) .This
feature helps keep meat and fish
fresh longer.

• Select Chill to set the temperature
of the Cool Select Room to 30 °F
(-1 °C).

• Select Cool to set the temperature
of the Cool Select Room to 41 °F
(5 °C). You can keep water, juice,
soft drinks, beer, etc. cold.

8

( 2 ) Freezer (Hold 3 sec for Power Freeze)

Touch this button to set the freezer
to your desired temperature.

4

5

6

You can set the temperature between

-8 °F and 5 °F (between -23 °C and

-15 °C).
Touch and hold this button for

3 seconds to decrease the time
needed to freeze products in the
Freezer. This can be helpful if you
need to quickly freeze easily spoiled
items or if the temperature in the
freezer has warmed dramatically (For
example, if the door was left open).

( 3 ) Alarm (Hold 3 sec for Filter Reset)

This button serves two purposes:

1) To turn the door open alarm on
and off
If the door alarm is set to On, an
alarm beeps if any refrigerator
door is left open for more than two
minutes.
The beeping stops when you close
the door. The door alarm function
is pre-set to On in the factory.
You can turn it off by touching and
then releasing this button.
You can turn it back on in the
same fashion. The icon lights up
when the function is on.
When the Door Alarm function
is on and the alarm sound is
triggered, the Door Alarm Icon will
blink while the alarm sounds.

2) To reset the water filter life
indicator.
After you replace the water filter,
touch and hold this button for 3
seconds to reset the water filter life
indicator.

16_ operating

DA68-02918A-05.indb 16 14. 6. 25. �� 10:57

( 4 ) Energy Saver

(Hold 3 sec for °C↔°F)

Touching this button turns Energy
Saver mode on and off. When you
turn Energy Saver on, the Energy
Saver icon lights.

Turn Energy Saver off and the icon
goes off. The Energy Saver function
is set to “ON” in the factory.
If condensation or water drops
appear on the doors, turn the Energy
Saver mode off.
Touch and hold this button for 3
seconds to switch the temperature
units between °C and °F.

( 5 ) Fridge (Hold 3sec for Power Cool)

Touch this button to set the fridge
to your desired temperature. You
can set the temperature between
34 °F and 44 °F (between 1 °C and
7 °C). Touch and hold this button
for 3 seconds to decrease the time
needed to cool products in the
Refrigerator. This can be helpful if you
need to quickly cool easily spoiled
items or if the temperature in the
fridge has warmed dramatically (For
example, if the door was left open).

( 6 ) Lighting (Hold 3 sec for child lock)

Touching this button sets the
Dispenser LED lamp (under the
display) to continuous mode so that
it stays on continuously.
The button also lights up. If you want
the Dispenser lamp to come on only
when some one uses the dispenser,
touch this button to turn the
continuous mode off. Also, pressing
this button for 3 seconds turns on
Child Lock which locks the display
panel and dispenser buttons so the
buttons can not be used. The Child
Lock icon lights up to indicate you’ve
activated the Child Lock function.
Press 3 seconds to unlock.

( 7 ) Ice Type

Press the Ice Type button to change
the ice type. Each time you press
the Ice Type button, the cubed and
crushed ice modes alternate and the
Cubed or Crushed ice icon lights up,
indicating your selection.

If you don’t need ice, turn the function
off to save on water and energy
consumption (See Ice Off below).

( 8 ) Ice Off (Hold 3 sec)

Press the Ice Off button for 3
seconds until the Ice Off Indicator
( ) illuminates.

( 9 ) Filter

Water filter usage

This icon will light up when you
need to change the filter. After you
use about 300 gallons of water, the
filter indicator lights up (in about 6
months). After you install the new
water filter, reset the filter indicator
by pressing the Alarm/hold 3 sec for
Filter Reset button.

• If water is not dispensing or

dispensing slowly, you need to
replace the water filter because
the water filter is clogged.

• Some areas have large amounts

of lime in their water, which
causes the water filter to clog
more quickly.

Cooling Off Mode

- North American (US, Canada) Models Only ;
Cooling Off mode (also called Shop
mode), is designed for use by retailers when they

are displaying refrigerators on the shop floor. In
Cooling Off mode, the refrigerator’s fan motor and
lights work normally, but the compressors do not
run, and the refrigerator and freezer do not get
cold. To start Cooling Off mode, touch and hold
the CoolSelect button and the Freezer button
for 5 seconds during normal operation. The
refrigerator chime sounds and the temperature
display flashes “OFF”.

To cancel Cooling Off mode, touch and hold the
CoolSelect and the Freezer buttons again for 5
seconds.

02 OPERATING

operating _17

DA68-02918A-05.indb 17 14. 6. 25. �� 10:57

CHANGING THE WATER FILTER

• To reduce risk of water damage to your

WARNING

USE ONLY SAMSUNG BRAND WATER FILTERS.
SAMSUNG will not be legally responsible for any
damage, including, but not limited to, property
damage caused by water leakage from the use of
a generic water filter. SAMSUNG Refrigerators are
designed to work ONLY WITH SAMSUNG Water
Filter.

The Filter light turns red to let you know
when it is time to change your water
filter cartridge.

To give you time to get a new filter,
the red light comes on just before the
capacity of the current filter runs out.
Changing the filter on time provides you with the
freshest, cleanest water from your refrigerator.

1. Shut off the water supply. Then, turn the water

2. Pull the water filter ( 1 ) from the case filter ( 2 ).

• Sometimes, it is hard to disassemble the water

• When you pull out

• To prevent overflow, empty the water filter tray

3. Insert the new filter into the filter case ( 4 ).

4. Push the filter in, and then turn it clockwise until

property DO NOT use generic brands
of water filters in your SAMSUNG
Refrigerator.

(Red)

filter ( 1 ) about 1/4 turn, counter-clockwise.

• To change the water filter more easily,
shut off the water supply valve.

filter because impurities in the water cause it to
stick. If you are having difficulties, grip the water
filter firmly and pull it hard.

the water filter, a little
water can leak from
the opening. This is
normal. To minimize
the water leaks, keep the filter cartridge
horizontal when you pull it.

( 3 ) and dry around the filter case ( 2 ).

it locks.

• The locked symbol should be lined up
with the indicator line.

4

5. Touch the “Alarm/hold
3 sec for Filter Reset”

button (

(Filter Reset)

) for about

3 seconds to reset the
water filter. The color of the

indicator ( ) changes from red to off.

6. If you turned off the water supply, turn it back
on.

• For a replacement water filter, visit your
local home Improvement center, go to
SamsungParts.com on line, or contact
your authorized Samsung dealer.
Be sure the replacement water filter has
the SAMSUNG logo on the box and on
the water filter.

2

Removing any residual matter inside the
water supply line after installing the water

1

filter.

1. Turn ON the main water
supply and supply water
from water supply line.

2. Run water through the
dispenser until the water
runs clear (approx. 6 to 7
minutes). This will clean
the water supply system and remove air from
the lines.

2

3. Additional flushing may be required in some
households.

3

4. Open the Refrigerator door and make sure
there are no water leaks coming from the water
filter.

• Be sure to flush the dispenser thoroughly,
otherwise water may drip from the
dispenser.
This means that there is still air in the line.

• If you have trouble inserting the water
filter because of high water pressure,
shut off the water supply valve.

18_ operating

DA68-02918A-05.indb 18 14. 6. 25. �� 10:57

Reverse Osmosis Water Supply
IMPORTANT:

The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet
valve of the refrigerator needs to be between 35
and 120 psi (241 and 827 kPa).
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi (276 to 414 kPa.) If
the water pressure to the reverse osmosis system
is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the
reverse osmosis system is blocked. Replace
the filter if necessary.

• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.

• If your refrigerator has a water filter, it may
further reduce the water pressure when used
in conjunction with a reverse osmosis system.
Remove the water filter.

If you have questions about your water pressure,
call a licensed, qualified plumber.

Freezer

The Freezer temperature can be set between -8°F
and 5 °F (or between -23 °C and -15 °C) to suit
your particular needs. Press the Freezer button
repeatedly until the desired temperature is shown
in the temperature display. The temperature will
change by 1 °F (or 1 °C) with each press.
See below.

Fahrenheit : 0 °F ➞ -1 °F ➞ -2 °F ➞ -3 °F ➞ -4 °F

-5 °F ➞ -6 °F ➞ -7 °F ➞ -8 °F ➞ 5 °F ➞ 4 °F ➞

➞

3 °F ➞ 2 °F ➞ 1 °F ➞ 0 °F.
Centigrade : -18 °C ➞ -19 °C ➞ -20 °C ➞ -21 °C

-22 °C ➞ -23 °C ➞ -15 °C ➞ -16 °C ➞ -17 °C

➞

-18 °C.

➞

• The Freezer or Fridge temp indicator
will blink when the temperature in the
fridge or freezer compartment goes up

(Freezer or Fridge temperature indicator will stop
blinking when temperature in the Freezer or Fridge
becomes normal. If temperature indicator does not
stop blinking after several hours, please contact
your service center.

dramatically.

02 OPERATING

CONTROLLING THE
TEMPERATURE

RECOMMENDED FREEZER AND
REFRIGERATOR COMPARTMENT
TEMPERATURES

The recommended temperatures for the Freezer
and Refrigerator Compartments are -19 °C
and 3°C (-2 °F and 38°F) respectively. If the
temperature of the Freezer and Refrigerator
Compartments are too high or low, adjust the
temperature manually.

CONTROLLING THE FREEZER
TEMPERATURE

Recommended Temp (Freezer) : -2 °F (-19 °C)

Power Freeze

The Power Freeze function substantially speeds up
the freezer compressor, causing the freezer to cool
down rapidly to a temperature you choose.
This icon will light up when you press and hold the
Freezer button for 3 seconds.

Power Freeze is useful if you need to quick freeze
an item, to make a large quantity of ice, or to cool
the freezer rapidly if it has warmed dramatically (for
example, if the door was left open).

To turn the Power Freeze function off manually,
press the Freezer button, and then re-set the
Freezer temperature.

Power Freeze turns off automatically after 50 hours
to decrease energy consumption.

When the Power Freeze function stops
automatically, it automatically sets the Freezer
temperature to -19 °C. Re-set the temperature if
necessary.

When you use this function, the energy
consumption of the refrigerator will increase.

If you need to freeze large amounts of food,
activate the Power Freeze function at least 20
hours before.

operating _19

DA68-02918A-05.indb 19 14. 6. 25. �� 10:57

CONTROLLING THE FRIDGE
TEMPERATURE

USING THE COLD WATER
DISPENSER

The fridge temperature can be set between
34 °F and 44 °F (or between 1 °C and 7 °C) to

suit your particular needs. Press the Fridge button
repeatedly until the desired temperature is shown
in the temperature display. The temperature will
change by 1 °F (or 1 °C) with each press.
See below.

Fahrenheit : 37 °F ➞ 36 °F ➞ 35 °F ➞ 34 °F ➞ 44
°F ➞ 43 °F ➞ 42 °F ➞ 41 °F ➞ 40 °F ➞ 39 °F ➞
38 °F ➞ 37 °F.

Centigrade : 3 °C ➞ 2 °C ➞ 1 °C ➞ 7 °C ➞ 6 °C

5 °C ➞ 4 °C ➞ 3 °C.

➞

Recommended Temp (Fridge) : 38 °F (3 °C)

• The temperature of the Freezer, Fridge or
Cool Select Pantry Zone may rise when
you open the doors too frequently, or if
a large amount of warm or hot food is

• This may cause the digital display to blink. Once

• If the blinking continues, you may need to “reset”

• If there is a communication error between the

placed inside.

the Freezer and Fridge temperature return to their
normal set temperatures, the blinking will stop.

the Refrigerator. Try unplugging the appliance,
wait for around 10 minutes, and then plug the
power cord back in.

Display and Main Controller, the Convertible
Display light may blink. If the blinking continues
for a long period of time, please contact a
Samsung Electronics Service Center.

Push the appropriate ice type button
to select what you want dispensed.

Using the ice lever ( 1 )

Push the Ice lever dispenser ( 1 ) gently with your
glass. Ice will be released from the dispenser.
You can choose the type of ice by pushing the
cubed or crushed button first.

Select this if you want to

NO ICE

turn ice maker off

Using the Water lever ( 2 )

Push the Water lever dispenser ( 2 )
gently with your glass. Water will be
released from the dispenser.

•

If you push the water and
Ice lever at about the
same time, the dispenser
operates only the option
you actually selected or pushed first.

• Please wait 1 second before removing
the cup after dispensing water to prevent
spills. Do not pull out the lever dispenser
after dispensing ice or water. It comes
back automatically.

1

2

Using the Ice & Water Dispenser together

To get Ice and water, push the Ice lever ( 1 ) first
for ice, then move your glass down and press the
water dispenser lever (2) for water.

MAINTAINING THE ICE BUCKET

• To clean the ice bin/bucket, wash with a mild
detergent, rinse well, and dry thoroughly. Do
not use harsh or abrasive cleaners or solvents.

• Ice is made in cubes. When you select
“Crushed”, the ice maker grinds the ice cubes
into crushed ice.

• When you select Cubed Ice after using the
Crushed Ice mode, a small amount of residual
crushed ice might be produced.

• The ice cubes generated by the rapid ice

20_ operating

DA68-02918A-05.indb 20 14. 6. 25. �� 10:58

making process will look white, which indicates
they are generated normally.

• If ice doesn’t come out, pull out the ice bucket
and press the Test button located on the right
side of ice maker. See the illustration under
Making Ice below.

• Do not press the Test button continuously if
the tray is filled with ice or water. Water may
overflow or ice may jam the bucket.

MAKING ICE

• To fill the ice bucket to maximum capacity after
installation, follow these steps:

1. Allow your refrigerator to operate and cool
down for 24 hours (or 1 full day).

- Waiting 24 hours will allow your ice maker to
cool properly.

2. Dispense 4 to 6 ice cubes into a glass.

3. After another 8, and then 16 hours, dispense a

full glass of ice.

• To test the ice maker, press the Test button
on the ice maker. You will hear the refrigerator
chime (ding-dong). When the chime sounds,
release the Test button.

• The chime sounds automatically again to let
you know the ice maker is working well.

check the
water level

• If a power failure occurs, ice cubes

CAUTION

may melt then freeze together when
the power comes back on, causing the

dispenser to stop working.
To prevent this problem, after a power failure, pull out
the ice bucket and discard the residual ice or water.

• If you use all the ice at once, you must
repeat Steps 2 and 3 above.

However, only wait 8 hours before dispensing the
first 4 to 6 ice cubes. This will replenish the ice
cubes and ensure maximum ice production.

Using the ice off Function

When you select the Ice Off mode, remove all ice
cubes from the bucket.
If you leave the ice cubes in the bucket, the ice
cubes may clump together, making it difficult to
remove them.
To remove the ice bucket safely and avoid injury,
hold the bottom of the bucket with one hand and
the side of the bucket with the other.
Then, lift up on the ice bucket, and pull it straight
out.
To put the ice bucket back in, push it firmly straight
back.

If the ice bucket is not pushed firmly into
place, ice in the bucket can melt.

If the bucket does not fit, turn the helix 90 degree
(see the last illustration on the right, below) and try
again.

02 OPERATING

Test button

• If you want to remove ice cubes without

CAUTION

using the ice bucket, turn the ice maker
off and remove the front cover from the
ice maker. Then, remove the ice cubes.
Note that with the cover removed, the ice
cubes in the ice maker can spill out.

• Do not put food in the ice bucket. If you

CAUTION

store food in the ice bucket, the food can
strike the ice maker when you open or
close the door, causing damage to the
ice maker.

• Note that the ice cubes in the ice bucket

CAUTION

may spill out over the drawer when you

• The inside of the ice bucket is very cold

CAUTION

when the refrigerator is operating.
Do not reach deep inside the ice bucket.

• Use only the ice maker provided with
the refrigerator. The water supply to
this refrigerator must only be installed/
connected by a suitably qualified person.
Connect to a potable water supply only.

- To operate the ice maker properly, water
pressure of 20 ~ 125psi is required.

remove the ice bucket from the drawer.
If this occurs, be sure to pick up any ice
cubes that spill.

operating _21

DA68-02918A-05.indb 21 14. 6. 25. �� 10:58

GOING ON VACATION...

If you are going on a long vacation or business trip
and won’t use the water or ice dispensers for a long
time:

- Close the water valve. Otherwise, water leakage
may occur.

- Remove all food.

- Unplug the refrigerator.

- Wipe excess moisture from inside and leave the
doors open. Otherwise, odor and mold may develop.

ICE MAKER DO’S AND DON’TS

Do not put your fingers, hands or any other
unsuitable objects in the chute or ice-maker bucket.

- You can hurt yourself or damage the refrigerator.
Never put your finger or any other objects in the
dispenser opening.

- You can injure yourself.
Do not try to disassemble the ice maker.
Do not wash or spray the ice bucket with water
while it is in the refrigerator.
Remove it to clean it

.

•

CAUTION

When you insert the Ice maker tray, be
sure that the tray is well centered at the
entrance.
Otherwise, the tray may be stuck.

Water clouding phenomenon

• All water provided to the refrigerator
flows through a core alkaline water filter.
In the filtering process, the pressure
of the water that has flowed out of the
filter has increased, and the water has
become saturated with oxygen and
nitrogen. When this water flows out into
the air, the pressure plummets and the
oxygen and nitrogen get supersaturated,
which results in gas bubbles. The water
may temporarily look misty or cloudy due
to these oxygen bubbles. After a few
seconds, the water will look clear.

PARTS AND FEATURES

Use this page to become more familiar with the parts and features of the Refrigerator.

Ice-Maker

Ice chute

Fridge Multi-Purpose

Guard

EZ Fresh Vegetable &

Fruit Drawers

EZ Freezer Slide-Shelf

Dry Food and Meat

Storage Bin

Freezer Door Bins

22_ operating

DA68-02918A-05.indb 22 14. 6. 25. �� 10:58

EZ Slide-Shelf

Foldable-Shelf
Egg tray

Water filter

Cool Select Room

For the greatest energy efficiency, leave all
selves, drawers,and baskets in their original
positions as shown in the illustration on the
previous page.

When closing the door, make sure the
Vertical Hinged Section is in the correct
position to avoid scratching the other door.

If the Vertical Hinged Section is reversed,
put it back into the correct position, and
then close the door.

Moisture may appear at times on the
Vertical Hinged Section.

The door handle may become loose over
time. If this happens, tighten the bolts found
on the inside of the door.

If you close one door with too much force,
the other door may open.

When the door opens, the interlock switch
automatically turns off the auger motor in
the ice maker for safety reasons.

If the interior or exterior LED lamp has gone
out, please contact Samsung service.

Do not adjust a bin full of food. Remove the
food first.

Dust removal method - Remove the guard and
wash in water.

2. Tempered Glass shelves
To remove - Tilt up the front of the shelf in the

direction shown (1) and lift it up vertically (2). Pull
the shelf out.

To relocate - Tilt the front of the shelf up and
guide the shelf hooks into the slots at a desired
height. Then, lower the front of the shelf so that the
hooks can drop into the slots.

The Tempered Glass shelves are heavy.

CAUTION

Use special care when removing them.

02 OPERATING

FRIDGE MULTI-PURPOSE DOOR BIN

A detachable divider makes it convenient to store
food.

Food products can be stored by items.

• Put the divider in place
when storing slim-size
condiment bottles and
canned drinks together.

• Take out the divider when
storing carton-size milks
or drinks.

REMOVING THE REFRIGERATOR
ACCESSORIES

1. Door Bins Compartment

To remove - Simply lift the bin up and pull straight

out.
To relocate - Slide it in above the desired location

and push down until it stops.

Injuries can occur if the door bins are not

CAUTION

firmly attached to the doors. Do not allow
children to play with the bins. Sharp corners
of the bins may cause injury.

1

2

3. Vegetable & Fruit Drawers (EZ Fresh Zone)

Holding the drawer with one hand, lift it up a little
bit while pulling it forward, and then pull it out of
the refrigerator.

Remove the door bins before removing the
drawer to prevent damage to the door bins.

operating _23

DA68-02918A-05.indb 23 14. 6. 25. �� 10:58

CLEANING THE REFRIGERATOR

Do not use benzene, thinner, Clorox, or car

WARNING

detergent to clean the refrigerator. They can
damage the surface of the appliance and
may cause a fire.

Do not spray the refrigerator with water while it is
plugged in, This can cause an electric shock.

To clean the refrigerator, follow these steps:

1. Unplug the power code of the refrigerator.

2. Slightly dampen a soft lint-free cloth or paper

towel with water.

Do not use any kind of detergent to clean
the refrigerator because that can discolor or
damage the refrigerator.

3. Wipe the inside and outside of refrigerator until
it is clean and dry.

4. Plug the power cord of the refrigerator back in.

CHANGING THE INTERIOR LIGHTS

Freezer / Fridge LED Lamp

• If the LED Lamp Cover is stained with foreign
substances, the LED lamp may not look bright.
Wipe the surface cover with clean dry cloth to
return the light to full brighteness.

• Do not disassemble or replace the LED

CAUTION

type lighting yourself. To replace the LED
lights, contact a Samsung service center

or your authorized Samsung dealer.
If you attempt to replace the LED lamps
yourself, you risk subjecting yourself to an
electric shock or serious personal injury.

24_ operating

DA68-02918A-05.indb 24 14. 6. 25. �� 10:58

troubleshooting

PROBLEM SOLUTION

The refrigerator
does not work at
all or it does not
chill sufficiently.

The food in the
fridge is frozen.

You hear unusual
noise or sounds.

The cabinet-door
sealing area of the
appliance is hot
and condensation
is occurring.

The Ice Maker is
not producing ice.

You can hear
water bubbling in
the refrigerator.

There is a bad
smell in the
refrigerator.

Frost forms on
the walls of the
freezer.

The water
dispenser is not
functioning.

The auto close
system does not
work with the
freezer door.

Condensation or
water drops forms
on both sides
of fridge door's
central part.

• Check that the power plug is properly connected.

• Check if the set temperature on the digital display is warmer than the freezer or fridge
inner temperature. If it is, set the freezer or fridge to a colder temperature.

• Is the refrigerator in direct sunlight or located near a heat source?

• Is the back of the refrigerator too close to the wall, preventing proper ventilation?

• Check if the set temperature on the digital display is too low.

• Try setting the refrigerator to a warmer temperature.

• Is the temperature in the room too low? Set the refrigerator warmer.

• Did you store the food which is juicy in the coldest part of the refrigerator? Try moving those
items to the other shelves in the fridge instead of keeping them in the colder areas or bins.

• Check that the refrigerator is level and stable.

• Is the back of the refrigerator too close to the wall, preventing proper ventilation?

• Try moving the back of the refrigerator at least 2 inches from the wall.

• Was anything dropped behind or under the refrigerator?

• A “ticking” sound is heard from inside the refrigerator. It is normal and occurs because
various accessories are contracting or expanding in response to temperature changes in
the refrigerator interior.

• If it sounds as if something is hitting something else inside the refrigerator, this is normal.
The sound is caused by the compressor operating at high capacity.

• Some heat is normal as anti-condensators are installed in the vertical hinged section of
the refrigerator to prevent condensation.

• Is the refrigerator door ajar? Condensation can occur when you leave the door open for
a long time.

• Did you wait for 12 hours after installing the water supply line before making ice?

• Is the water line connected and the shut-off valve opened?

• Did you manually stop the ice making function?

• Is the freezer temperature too warm? Try setting the freezer temperature lower.

• This is normal. The bubbling comes from refrigerant circulating through the refrigerator.

• Check for spoiled food.

• Foods with strong odors (for example, fish) should be tightly covered.

• Clean out your freezer periodically and throw away any spoiled or suspicious food.

• Is the air vent blocked? Remove any obstructions so air can circulate freely.

• Allow sufficient space between the stored food for efficient air circulation.

• Is the freezer drawer closed properly?

• Is the water line connected and the shut-off valve opened?

• Has the water supply line tubing been crushed or kinked?

• Make sure the tubing is free and clear of any obstruction.

• Is the water tank frozen because the fridge temperature is too low?
Try selecting a warmer setting on the Digital display.

• Is there an imbalance between the right and left parts of the door?

• Open and close the door smoothly 1~2 times. After you do this, the auto close system
usually works properly again.

• Try opening the door smoothly to avoid unbalancing the right part and the left part of the
door.

• Condensation or water drops may form if the humidity is too high while the refrigerator is
operating.

• If condensation or water drops appears on both sides of fridge door's central part, turn
the Energy Saver mode off after removing the condensation.

03 TROUBLESHOOTING

troubleshooting _25

DA68-02918A-05.indb 25 14. 6. 25. �� 10:58

Warranty: USA

WARRANTY ON SAMSUNG REFRIGERATOR

LIMITED WARRANTY TO ORIGINAL PURCHASER
This Samsung brand product, as supplied and distributed by Samsung Electronics America, Inc. (Samsung)

and delivered new, in the original carton to the original consumer purchaser, is warranted by Samsung against
manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year Parts and Labor on Refrigerator
Five (5) years Parts and Labor on sealed Refrigeration system only*
Ten (10) years Parts and Five (5) years Labor on Digital Inverter Compressor

(*Compressor, evaporator, condenser, drier, connecting tubing)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in

the United States. To receive warranty service, the purchaser must contact Samsung for problem determination
and service procedures. Warranty service can only be performed by a Samsung authorized service center.
The original dated bill of sale must be presented upon request as proof of purchase to Samsung or Samsung
authorized service center.

Samsung will repair or replace any part found to be defective, at our option and at no charge as stipulated
herein, with new or reconditioned parts during the limited warranty period specified above. All replaced parts and
products become the property of Samsung and must be returned to Samsung. Replacement parts and products
assume the remaining original warranty, or ninety (90) days, whichever is longer.

In-home service will be provided during the warranty labor period subject to availability within the contiguous
United States. In-home service is not available in all areas. To receive in-home service, the product must be
unobstructed and accessible from floor level to service personnel. If during in-home service repair cannot be
completed, it may be necessary to remove, repair and return the product. If in-home service is unavailable,
Samsung may elect, at our option, to provide for transportation of our choice to and from a Samsung authorized
service center. Otherwise, transportation to and from the Samsung authorized service center is the responsibility
of the purchaser.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,
noncommercial use of this product, and shall not apply to the following, including, but not limited to: damage
which occurs in shipment; delivery and installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire,
water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies,
accessories, applications, installations, repairs, external plumbing and leaks, external wiring, circuit breakers,
fuses or connectors not supplied and authorized by Samsung, or which damage this product or result in service
problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow
operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in
the instruction book; loss of food due to spoilage; consumable items including filters and light.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND
NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY
AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY
OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT
SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR
PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT,
REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST
SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG
AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL
RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY
AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS
PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state.
To obtain warranty service, please contact Samsung at:

SAMSUNG CUSTOMER CARE CENTER

Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660
1-800-SAMSUNG (1-800-726-7864) and www.samsung.com

DA68-02918A-05.indb 26 14. 6. 25. �� 10:58