Thank you for purchasing this Samsung product.
To receive more complete service or accessory parts,
please register your product at or contact
www.samsung.com/register
1-800-SAMSUNG (726-7864)
Free Standing Appliance
This manual is made with 100% recycled paper.
English
RF323TE
DA68-02603A-03.indb 113. 4. 25. �� 2:12
safety information
SAFETY INFORMATION
Before using your new Samsung French Door
Refrigerator, please read this manual thoroughly to
ensure that you know how to operate the features
and functions that your new appliance offers safely
and efficiently.
This appliance is not intended for use by persons
(including children) with reduced physical,
sensory, or mental capabilities, or those who lack
experience and knowledge, unless they have been
given supervision or instruction concerning the
use of the appliance by a person responsible for
their safety.
Because the following instructions cover various
models, the characteristics of your refrigerator
may differ slightly from the refrigerator described in
this manual. If you have any question, contact us
at 1-800-SAMSUNG or find help and information
online at www.samsung.com.
Important safety symbols and
precautions:
Hazards or unsafe practices that may result in
WARNING
severe personal injury or death.
Hazards or unsafe practices that may result in
CAUTION
minor personal injury or property damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug from the wall socket.
Make sure the refrigerator is grounded to
prevent electric shock.
Call the contact center for help.
Note.
These warning symbols are here to prevent
injury to you and others.
Please follow them carefully.
After reading this section, keep it in a safe
place for future reference.
02_ Safety information
CRITICAL INSTALLATION
WARNINGS
WARNING
• Do not install the refrigerator in a damp
place or place where it may come in
- Deteriorated insulation on electrical parts may
• Do not place this refrigerator in direct sunlight
• Do not plug several appliances into the same
- This provides the best performance and
• If the wall socket is loose, do not insert the
- There is a risk of electric shock of fire.
• Do not use a cord that shows cracks or abrasion
• Do not bend the power cord excessively or
• Do not twist or tie the power cord.
• Do not hook the power cord over a metal
- When moving the refrigerator, be careful not to
- This may result in an electric shock or fire.
• Never unplug your refrigerator by pulling on the
- Damage to the cord may cause a short-circuit,
• Do not use aerosols near the refrigerator.
- Using aerosols near the refrigerator may cause
• Do not install this appliance near a heater,
• Do not install this appliance in a humid, oily or
contact with water.
cause an electric shock or fire.
or expose it to the heat from stoves, room
heaters, or other appliances.
multiple power strip. The refrigerator should
always be plugged into its own individual
electrical outlet which has a voltage rating that
matches the voltage listed on the refrigerator’s
rating plate.
also prevents overloading house wiring
circuits, which could cause a fire hazard from
overheated wires.
power plug.
damage along its length or at either end.
place heavy articles on it.
object, place a heavy object on the power
cord, insert the power cord between objects,
or push the power cord into the space behind
the appliance.
roll over or damage the power cord
power cord. Always grip the plug fi rmly and
pull straight out from the outlet.
fire, and/or electric shock.
an explosion or fire.
inflammable material.
dusty location, in a location exposed to direct
sunlight and water (rain drops).
DA68-02603A-03.indb 213. 4. 25. �� 2:12
• Do not install this appliance in a location where
gas may leak.
- This may result in an electric shock or fire.
• This refrigerator must be properly
located and installed in accordance with
the instructions in this manual before
you use it.
• Connect the power plug in the proper position
with the cord hanging down.
- If you connect the power plug upside down,
the wire can get cut off and cause a fire or
electric shock.
• When moving the refrigerator, be careful not to
roll over or damage the power cord.
- This constitutes a fire hazard.
• Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
• Keep the packing materials out of reach of children.
- There is a risk of death from suffocation if a child
puts the packing materials on his or her head.
• The appliance must be positioned so that the
plug is accessible after installation.
• You need to remove all the protective plastic
film before you initially plug the product in.
• The refrigerator must be safely grounded.
- Always make sure that you have
grounded the refrigerator before
attempting to investigate or repair any
part of the appliance. Power leakages
can cause severe electric shock.
• Never use gas pipes, telephone lines, or other
potential lightning attractors as an electrical
ground.
- Improper use of the grounding plug can result
in a risk of electric shock. If it is necessary
to use an extension cord, use only a 3-wire
extension cord that has a 3-blade grounding
plug and a 3-slot receptacle that will accept
the plug on the appliance. The marked rating
of the extension cord should be AC115-120 V,
10 A, or more. If a grounding adapter is used,
make sure the receptacle box is fully grounded.
• If the power cord is damaged,
have it replaced immediately by the
manufacturer or its service agent.
INSTALLATION CAUTIONS
CAUTION
• Allow sufficient space around the
refrigerator and install it on a flat surface.
- If your refrigerator is not level, the internal
cooling system may not work correctly.
• Keep the ventilation space in the appliance
enclosure or mounting structure clear of
obstruction.
• Allow the appliance to stand for 2 hours after
installation.
• We recommend you have installed this refrigerator
by a qualified technician or service company.
- Failing to do so may result in an electric shock,
fire, explosion, problems with the product, or
injury.
WARNING
CRITICAL USAGE WARNINGS
• Do not insert the power plug with wet
hands.
•
Do not store articles on the top of the appliance.
- When you open or close the door, the articles
may fall and cause personal injury and/or
material damage.
• Do not put a container filled with water on the
refrigerator.
- If spilled, there is a risk of fire or electric shock.
• Children should be supervised to ensure that
they do not play with the appliance.
- Keep fingers out of “pinch point” areas;
clearances between the doors and cabinet are
necessarily small. Be careful when you open
the doors when children are in the area.
• Do not let children hang on the door. A serious
injury may occur.
• Do not let children go inside the refrigerator.
Children could become trapped.
• Do not insert your hands into the bottom area
under the appliance.
- Any sharp edges may cause personal injury.
• Do not let children step on a drawer cover.
- The drawer may break and cause them to slip.
• Do not overfill the refrigerator with food.
- When you open the door, an item may fall out
and cause personal injury or material damage.
• Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
- This may cause frostbite.
• Never put fingers or other objects into the
water dispenser hole, ice chute, or ice maker
bucket.
- It may cause personal injury or material damage.
• Do not spray flammable gas near the refrigerator.
- There is a risk of explosion or fire.
• Do not store volatile or flammable substances
Safety information _03
DA68-02603A-03.indb 313. 4. 25. �� 2:12
in the refrigerator.
- Storing benzene, thinner, alcohol, ether, LP gas
and other such products in the refrigerator may
cause explosions.
• Do not store pharmaceutical products,
scientific materials, or temperature sensitive
products in the refrigerator.
- Products that require strict temperature
controls must not be stored in the refrigerator.
• Do not place or use an electrical appliance
inside the refrigerator, unless it is of a type
recommended by the manufacturer.
• Do not stand on top of the appliance or place
objects (such as laundry, lighted candles,
lighted cigarettes, dishes, chemicals, metal
objects, etc.) on the appliance. This may result
in an electric shock, fire, problems with the
product, or injury. Do not put a container filled
with water on the appliance.
- If spilled, there is a risk of fire or electric shock.
• Do not use mechanical devices or any other
means to accelerate the defrosting process,
other than those recommended by the
manufacturer.
• Do not damage the refrigerant circuit.
• Do not spray volatile material such as
insecticide onto the surface of the appliance.
- As well as being harmful to humans, it may
also result in an electric shock, fire or problems
with the product.
• Never stare directly at the UV LED lamp for
long periods of time.
- This may result in eye strain due to the
ultraviolet rays.
• Do not disassemble or repair the
refrigerator yourself.
- You run the risk of causing a fi re, malfunction,
and/or personal injury.
- When the interior or exterior LED lamp has
gone out, please contact your service agent.
• Children should be supervised to ensure
that they do not play with the appliance.
- Keep fingers out of “pinch point” areas :
clearances between the doors and cabinet are
necessarily small. Be careful when you open
the doors when children are in the area. Do not
let children hang on the door. If not, a serious
injury may occur. Risk of children entrapment.
Do not let children enter inside the refrigerator.
• Bottles should be stored tightly together so
that they do not fall out.
• This product is intended only for the storage of
food in a domestic environment.
• If a gas leak is detected, avoid any naked flames
04_ Safety information
or potential sources of ignition and air the room in
which the appliance is standing for several minutes.
- Do not touch the appliance or power cord.
- Do not use a ventilating fan.
- A spark may result in explosion or fire.
• Use only the LED Lamps provided by the
manufacturer or its service agents.
• If the refrigerator emits a burning smell or
smoke, pull the power plug immediately
and contact your Samsung Electronics
service center.
• IIf you experience difficulty changing a nonLED light, contact a Samsung service energy.
• If the product is equipped with LED Lamps, do
not disassemble the Lamp Covers and LED
Lamps yourself.
- Please contact your service agents.
• If dust or water enters the refrigerator, pull out
the power plug and contact your Samsung
Electronics service center.
- Otherwise there is a risk of fire.
CAUTION
USAGE CAUTIONS
• Do not re-freeze frozen foods that
have thawed completely. Do not place
carbonated or fizzy drinks in the freezer
compartment. Do not put bottles or
glass containers in the freezer.
- When the contents freeze, the glass may break
and cause personal injury.
• Use only the ice maker provided with the
refrigerator. The water supply to this refrigerator
must only be installed/connected by a suitably
qualified person and connected to a potable
water supply only. In order to operate the
ice maker properly, water pressure of 20 ~
125psi is required. If you have a long vacation
or business trip and won’t use water or ice
dispensers, close the water valve.
- Otherwise, water leakage may occur.
• Wipe excess moisture from the inside and
leave the doors open.
- Otherwise, odor and mold may develop.
• Service Warranty and Modifi cation.
- Any changes or modifi cations
performed by a 3rd party on this
finished appliance are not covered
under Samsung warranty service, nor is
Samsung responsible for safety issues
that result from 3rd party modifi cations.
• Do not block the air holes.
- If the air holes are blocked, especially with a
plastic bag, the refrigerator can be over cooled.
DA68-02603A-03.indb 413. 4. 25. �� 2:12
If this cooling period lasts too long, the water
filter may break and cause water leakage.
• If the refrigerator is disconnected from the
power supply, you should wait for at least five
minutes before plugging it back in.
• If you have a long vacation planned or do
not intend to use the refrigerator for a long
period of time, empty the refrigerator, pull out
the power plug, wipe excess moisture from
the inside walls, and leave the doors open to
prevent odors and mold.
- Letting the refrigerator run long periods of time
without using it can cause the insulation to
deteriorate and may cause a fire.
• To get the best performance from the product:
- Do not place food too close to the vents at the
rear of the appliance as it can obstruct free air
circulation in the refrigerator compartment.
- Wrap food up properly or place it in airtight
containers before putting it into the refrigerator.
• Fill the water tank and ice tray with potable
water only.
• If the product is flooded, make sure to
- There is a risk of electric shock or fire.
CAUTION
- There is a risk of fire or electric shock.
• Do not use a hair dryer to dry the inside of the
- This may result in an electric shock or fire.
- Otherwise, there is a risk of fire or electric shock.
contact your nearest service center.
CLEANING CAUTIONS
• Do not directly spray water on the inside
or outside the refrigerator.
refrigerator. Do not place a lighted candle in
the refrigerator to remove bad odors.
• Remove any foreign matter or dust from
the power plug pins. Do not use a wet
or damp cloth when cleaning the plug.
• Unplug the refrigerator before cleaning
or making repairs.
State of California Proposition
65 Warnings:
WARNING
The California Safe Drinking Water and Toxic
Enforcement Act requires the Governor of
California to publish a list of substances known
to the State of California to cause cancer, birth
defects, or other reproductive harm, and requires
businesses to warn of potential exposure to such
substances.
This product contains a chemical known to
the State of California to cause cancer, birth
defects, or other reproductive harm. This
appliance can cause low-level exposure to some
of the substances listed, including benzene,
formaldehyde, and carbon monoxide.
CRITICAL DISPOSAL
WARNINGS
WARNING
• Risk of child entrapment. Before you
- Take off the doors.
- Leave the shelves in place so that children can
• Please dispose of the packaging material from
• Ensure that none of the pipes on the back of
• R600a or R134a is used as a refrigerant. Check
• When disposing of this refrigerator, remove the
• Cyclopentane is used in the insulation. The
throw away your old refrigerator or freezer:
not easily climb inside.
this product in an environmentally friendly manner.
the appliance are damaged prior to disposal.
the compressor label on the rear of the appliance
or the rating label inside the fridge to see which
refrigerant is used for your refrigerator. If this
product contains flammable gas (Refrigerant
R600a), contact your local authority in regard to
safe disposal of this product.
door/door seals and door latch so that small
children or animals cannot become trapped
inside. Children should be supervised to ensure
that they do not play with the appliance.
gases in the insulation material require a special
disposal procedure. Please contact your local
authorities in regard to the environmentally safe
disposal of this product.
contents
SETTING UP YOUR FRENCH DOOR REFRIGERATOR ……………………………………………… 06
OPERATING YOUR FRENCH DOOR REFRIGERATOR ………………………………………………… 12
TROUBLESHOOTING ……………………………………………………………………………………… 24
Safety information _05
DA68-02603A-03.indb 513. 4. 25. �� 2:12
Setting up your French Door
Refrigerator
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on your purchase of this Samsung
French Door Refrigerator.
We hope you enjoy the state-of-art features and
efficiencies that this new appliance offers.
Selecting the best location for the
refrigerator
Choose :
• A location with easy access to a water supply.
• A location without direct exposure to sunlight.
• A location with a level floor.
• A location with enough space for the
refrigerator doors to open easily.
• A location that allows sufficient space to the
right, left, back and top for air circulation.
• A location that allows you to move the
refrigerator easily if it needs maintenance or
service.
2 inches
3/4
2 inches
3 inches
The following chart details the exact height and
depth of this Samsung French Door Refrigerator.
ModelRF323T**
Depth “A”35 1/2" (901mm)
Width “B”35 6/8” (908mm)
Height “C”68 7/8” (1749mm)
Overall Height “D”70” (1777mm)
Depth “E”37 7/8” (963mm)
• Allow clearance to the right, left, back and top
when installing. This will help reduce power
consumption and keep your energy bills lower.
• Do not install the refrigerator where the
temperature will go below 50ºF (10ºC).
• Do not locate the refrigerator where it may
become wet.
B
B
A
A
E
E
C
C
D
D
If the refrigerator does not have enough space,
the internal cooling system may not work properly.
If your refrigerator has an ice maker, allow extra
space at the back for the water line connections.
When you install the refrigerator next to a fixed
wall, you need a minimum clearance of 3 ¾”
(95mm) between the refrigerator and wall to allow
the door to swing open.
Important : Make sure that you can easily move
your refrigerator to its final location by measuring
doorways (both width and height), thresholds,
ceilings, stairways, etc.
06_ setting up
DA68-02603A-03.indb 613. 4. 25. �� 2:12
When moving your refrigerator
To prevent floor damage, be sure the front
CAUTION
adjusting legs are in the up position (above
the floor). Refer to ‘Adjusting the Level’ in
the manual (on page 9).
Required Tools (Not provided)
You need the following tools to complete the
installation of your refrigerator:
Philips
screwdriver(+)
Flat-blade screw
driver(-)
Socket wrench
(10mm)
01 SETTING UP
Flat-blade screw
driver(-)
Control Lever
FLOORING
For proper installation, you must place this
refrigerator on a level, hard surface that is the
same height as the rest of the floor. This surface
should be strong enough to support a fully loaded
refrigerator, or approximately 359lbs (165kg).
To protect the finish of the flooring, cut a large
section of the cardboard carton and place it under
the refrigerator where you are working. When
moving the refrigerator, you need to pull and push
it straight forwards or back. Do not wiggle it from
side to side.
ACCESSORIES AND
REQUIRED TOOLS
The following accessories are included with your
refrigerator:
Pliers
Allen wrench
(3/16”) (5mm)
REMOVING THE
REFRIGERATOR DOORS
For some installations you need to remove the
fridge and freezer drawers so you can move the
refrigerator to its final location. Do not remove the doors/drawer if you don’t need to. If you
do not need to remove the refrigerator doors, go
to Adjusting the Level on page 9. If you need to
remove the doors. continue below.
Before removing the door/drawer, make sure you
read the following items:
Disconnect power to the refrigerator before
WARNING
removing the door or drawer.
• Be careful not to drop, damage, or
scratch the door/drawer while removing
• Use care when you remove the doors/drawer.
• Reattach the doors/drawer properly to avoid:
- Moisture from air leakage.
- Uneven door alignment.
- Wasting energy due to improper door seal.
Disassemble the refrigerator doors
WARNING
them.
The doors are heavy and you could injure
yourself.
Be careful not to drop and scratch the
doors while removing them.
Hex wrenchFastener
setting up _07
DA68-02603A-03.indb 713. 4. 25. �� 2:12
With the door opened
1. Remove 3 screws holding down the TOP TABLE ( 1 ) and separate wires connected.
5. Remove the screw ( 8 ) attached to the
lower left and right door hinges with a philips
screwdriver (+). Remove the 2 hex head bolts
( 9 ) attached to the lower left and right door
hinges with an allen wrench (3/16”). Remove
the lower left and right door hinges ( 10 ).
1
2. Disconnect two connector ( 2 ) on the left side
door. To remove the water coupler from the
hinge, twist and pull it from the hinge. Remove
the water line ( 3 ) while pressing the marked
part ( 4 ) of the water line coupler.
If a red clip is on the coupler, it must be
CAUTION
removed before removing the tube.
2
Red Clip
(1/4")
3
4
3. Pull and remove the hinge lever ( 5 ) . Remove
the ground screw ( 6 ) attached to the upper
left door hinges with a philips screwdriver (+).
Remove the upper left and right door hinges ( 7 ).
5
6
10
8
9
Allen wrench
REATTACHING THE
REFRIGERATOR DOORS
To reattach the fridge doors after you have moved
the fridge to its fi nal location, assemble the parts
in reverse order.
1. The Water Line must be fully inserted to the
center of transparent coupler (Type A) or the
Guide Lines (Type B) to prevent water leakage
from the dispenser.
2. Insert
the clip in the install pack and check that it
holds the line firmly.
Type AType B
Dispenser
Center of Transparent coupler
clip A (1/4”)
(6.35 mm)
The Guide Lines
clip A (1/4”)
(6.35 mm)
7
DISASSEMBLE THE FLEX DOOR
1. Take out the upper drawer by lifting it up.
4. Lift the door straight up to remove.
2. Remove the freeze room guard ( 1 ) by lifting
the guard up.
1
08_ setting up
DA68-02603A-03.indb 813. 4. 25. �� 2:12
3. Take out the lower basket ( 2 ) by lifting the
basket up from the rail system.
2
4. Press the fixing hook of the rail system.
5. Holding the top of the Freezer Drawer, pull it out all
the way, and then remove it from the rail system.
Be careful not to scratch or dent the sliding
CAUTION
rail by letting it strike the floor.
Make sure that you mount the freezer
CAUTION
basket in the right position when removing
/ installing the freezer door. Failing to do
so may result in the door not opening or
closing properly.
ASSEMBLE THE FREEZER DRAWER
To reattach the drawer after you have moved
the fridge to its fi nal location, assemble the parts
in reverse order.
ADJUSTING THE LEVEL
Make sure the refrigerator is level so that you can
make final adjustments. Use a level to test if the
refrigerator is level both side to side and back to
front. If the refrigerator is not level, it will not be
possible to get the doors perfectly even, which
may cause moisture condensation and increased
energy bills. Below is an example of how to level
the refrigerator if the left side of the refrigerator is
lower than the right side.
How to adjust the level
1. Open the freezer drawer and remove the lower
basket.
2. Insert a flat-blade screwdriver (-) into a notch
on the left control lever, and turn it counterclockwise to level the refrigerator. (You turn the
lever clockwise to lower the refrigerator and
counterclockwise to raise it.)
01 SETTING UP
Putting too much food into the freezer
CAUTION
drawers can prevent the freezer from
closing completely and can cause frost
flat-blade screwdriver (-)
Control Lever
build-up.
Both control levers must be touching the
CAUTION
floor to avoid possible personal injury or
property damage because of tipping.
If the right side is lower, perform the same
procedure, but with the right control lever.
It is difficult to remove the cover leg
front from the refrigerator, so we do not
recommend making small adjustments
with the control lever. Instead, refer to the
next page for the best way to make minor
adjustments to the doors.
setting up _09
DA68-02603A-03.indb 913. 4. 25. �� 2:12
MAKING MINOR
ADJUSTMENTS BETWEEN
DOORS
Remember, a leveled refrigerator is necessary
for getting the doors perfectly even. If you need
help, review the previous section on leveling the
refrigerator.
Adjustment
Fixed part
The left door is fixed. To make minor
adjustments between doors, adjust only
the right door.
1. Pull out the freezer drawer ( 1 ) to reveal the
lower hinge ( 2 ).
2. Insert the supplied allen wrench (3/16”) ( 3 )
into the shaft ( 4 ) of the lower hinge.
3. Adjust the height by turning the hex wrench ( 3 )
clockwise (
DOWN
) or counter clockwise ( UP ).
When you turn the hex wrench counterclockwise (), the door will move up.
2
4
1
part
3
2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 0.04”.
INSTALLING THE WATER
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.
The water line also connects to the ice maker.
For the ice maker to operate properly, water
pressure of 20~125 psi (138~862 kPa) is required.
If the refrigerator is installed in an area with low
water pressure (below 20psi), you can install
a booster pump to compensate for the low
pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator
is properly filled. To do this, press the water
dispenser lever until the water runs from the water
outlet.
Water line installation kits are available at
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper tubing
and ¼” compression nut.
Connecting to the water supply line
1. First, shut off the main water
supply.
3
2. Locate the nearest cold water drinking line and
install the pipe clamp and shut off valve.
4. After adjusting the doors, insert the supplied
fastener ( 6 ) using a pliers ( 5 ) in the gap
between the hinge-grommet ( 7 ) and the lower
Cold water line
Pipe clamp
hinge ( 8 ). The number of fasteners you’ll need
to insert depends on the gap.
Shut off valve
3. Connect the water line installation kit to the
shut off valve.
10_ setting up
DA68-02603A-03.indb 1013. 4. 25. �� 2:12
Cold water line
Pipe clamp
Shut off valve
Water line installation kit
Connecting the water supply line to
the refrigerator.
There are several items that you need to purchase
to complete this connection.
You may find these items sold as a kit at your local
hardware store.
Use Copper TubingUse Plastic Tubing
• ¼” copper tubing
• ¼” compression nut (1pc)
• Ferrule (2pc)
Compression
Nut (1/4”)
(Assembled)
Ferrule
(Not supplied)
Copper tubing
(Not supplied)
Household water supply line
1. Connect the household water line to the
assembled compression fitting.
- If you are using copper tubing, slip the
compression nut ( B ) (not supplied) and
ferrule (not supplied) on the copper tubing (not
supplied) as shown.
- If you are using plastic tubing ( B ) , insert the
molded end (Bulb) of the plastic tubing ( B )
into the compression fitting.
Do not use without the molded end (Bulb)
CAUTION
of the plastic tubing ( B ).
2. Tighten the compression nut ( B ) onto the
compression fitting.
• ¼” plastic tubing
Molded end(Bulb)
→
• ¼” compression nut (1pc)
Refrigerator
Plastic Tubing
(Assembled)
Compression
Fitting
(Assembled)
Molded
end(Bulb)
Compression
nut (B) (1/4”)
(Not supplied)
Plastic tubing (B)
or
(Not supplied)
Do not over-tighten the compression nut ( B ) .
3. Turn water on and check for any leakage. If you
find water drops or leakage in the connection
areas, turn off the main water supply. Check
the connections and, if necessary, tighten.
4.
Flush 1 gallon of water through the filter before
drinking or using the water from the refrigerator.
(Flush approximately 6 minutes.) To flush,
press a large glass or cup against the water
dispenser lever. Fill the glass, empty it into the
kitchen sink after it is filled, and then repeat.
5. After you turn on the refrigerator, let the ice
maker make ice for 1 to 2 days. Over that
period of time, throw out the first 1 or 2 buckets
of ice the freezer makes to ensure all impurities
have been removed from the water line.
Only connect the water line to a drinkable
water source.
If you have to repair or disassemble the water line,
cut off 1/4“ of the plastic tubing to make sure you
get a snug, leak-free connection.
You can test the water line quickly using a
paper cup. Under normal conditions, the
water dispenser can fill a 5.75 oz. (170cc)
cup in about 10 seconds.
COMPLETING THE SET UP
Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
1. Make sure your refrigerator is in an appropriate
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
2. Once the refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
4. After you plug the refrigerator in, it will
take a few hours to reach the appropriate
temperature. You can store food and drinks
in the refrigerator after the temperature is
sufficiently cool.
If condensation or water drops appears on
both sides of fridge door’s central part, turn
the Energy Saver mode off after removing
the condensation.
(See the explanation on Energy Saver button
in the USING THE CONTROL PANEL.)
setting up _11
01 SETTING UP
DA68-02603A-03.indb 1113. 4. 25. �� 2:12
Operating your French Door
Refrigerator
USING THE CONTROL PANEL
RF323TE**
1
2
3
78
( 1 ) Energy
Saver
( 2 ) Freezer
(Hold 3 sec
for Power
Freeze)
( 3 ) Alarm
/ hold 3sec
for Filter
Reset
109
Touching this button turns Energy Saver
mode on and off. When you turn Energy
Saver on, the Energy Saver icon lights.
Turn Energy Saver off and the icon
goes off. The Energy Saver function
automatically turns on when power is
supplied to the refrigerator.
If condensation or water drops appear
on the doors, turn the Energy Saver
mode off.
Touch this button to set the freezer to
your desired temperature.
You can set the temperature between
-8°F and 5°F (between -23°C and
-15°C). Touch and hold this button for 3
seconds to decrease the time needed
to freeze products in the Freezer. It can
be helpful if you need to quickly freeze
easily spoiled items or if the temperature
in the freezer has warmed dramatically
(For example, if the door was left open).
This button serves two purposes:
1) To turn the door open alarm on and off
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left
open for more than three minutes.
The beeping stops when you close the
door. The door alarm function is preset to On in the factory. You can turn it
off by touching and then releasing this
button. You can turn it back on in the
same fashion. The icon lights up when
the function is on.
2) To reset the water filter life indicator.
After you replace the water filter, touch
and hold this button for 3 seconds to
reset the water filter life indicator.
4
5
6
( 4 )
Lighting/
Hold 3 sec
for C↔F
( 5 ) Fridge
(Hold 3sec
for Power
Cool)
( 6 ) Ice Off
(Hold 3 sec
for child
lock)
(7) Cubed
Ice
(8) Crushed
Ice
(Cubed) (Crushed)
Cooling Off
Mode
Touching this button turns on the
Dispenser LED lamp (under the display)
in continuous mode so that it stays on
continuously. The button also lights
up. If you want the Dispenser lamp to
come on only when some one uses the
dispenser, touch this button to turn the
continuous mode off. Touch and hold
this button for 3 seconds to switch the
temperature units between °C and °F.
Touch this button to set the fridge to
your desired temperature. You can set
the temperature between 34°F and 44°F
(between 1°C and 7°C). Touch and hold
this button for 3 seconds to decrease
the time needed to cool products in
the Refrigerator. It can be helpful if you
need to quickly cool easily spoiled items
or if the temperature in the fridge has
warmed dramatically (For example, if the
door was left open).
If you don’t want to make more ice,
touch this button. Also, pressing this
button for 3 seconds turns on Child
Lock which locks the display panel and
dispenser buttons so the buttons can not
be used. The Child Lock icon lights up to
indicate you’ve activated the Child Lock
function. Press 3 seconds to unlock.
Press the Cubed Ice or Crushed Ice
button to select the type of ice you
want dispensed. Each time you press
the button, the cubed and crushed
ice modes alternate and the Cubed or
Crushed ice icon lights up, indicating
your selection.
If you don’t need ice, turn the function
off to save on water and energy
consumption (See Ice Off below).
Cooling Off mode (also called Shop
mode), is designed for use by retailers
when they are displaying refrigerators on
the shop floor. In Cooling Off mode, the
refrigerator’s fan motor and lights work
normally, but the compressors do not
run, and the refrigerator and freezer do
not get cold. To start Cooling Off mode,
touch and hold the Energy Saver button
and the Freezer button for 5 seconds
during normal operation. The refrigerator
chime sounds and the temperature
display flashes OF OF.
To cancel Cooling Off mode, touch and
hold the Energy Saver and the Freezer
buttons again for 5 seconds.
12_ operating
DA68-02603A-03.indb 1213. 4. 25. �� 2:12
( 9 ) Ice Off
If you don’t want to make more ice,
touch the Ice Off button.
The icon will light up and the Ice-Maker
stops making ice.
We recommend you to stop ice
making if the following occur:
-
There is enough ice in the ice bucket.
-
You want to save water and energy.
- Water is not being supplied to
the refrigerator.
If the ice maker function is
ON, and the water Line is not
connected, there will be a water
valve noise from the back of the
unit. press the Ice Off (Hold 3sec
for child lock) button for less
than 3 seconds until the Ice Off
Indicator ( ) illuminates.
The function key will operate after you remove
your finger from the letters except E.Saver, Ice
and Water key.
( 10 ) Filter Water filter usage
This icon will light up when you need to
change the filter. After you use about
300 gallons of water, the filter indicator
lights up. (about 6 months). After you
install the new water filter, reset the filter
indicator by touching the Alarm/hold 3
sec for Filter Reset button.
• If water is not dispensing or
dispensing slowly, you need to
replace the water filter because
the water filter is clogged.
• Some areas have large amounts
of lime in their water, which
causes the water filter to clog
more quickly.
CHANGING THE WATER FILTER
To reduce risk of water damage to your
WARNING
property DO NOT use generic brands
of water filters in your SAMSUNG
Refrigerator.
USE ONLY SAMSUNG BRAND WATER FILTERS.
SAMSUNG will not be legally responsible for any
damage, including, but not limited to property
damage caused by water leakage from the use of
a generic water filter. SAMSUNG Refrigerators are
designed to work ONLY WITH SAMSUNG Water
Filter.
The Filter light turns red to let you
know when it is time to change your
water filter cartridge.
To give you time to get a new filter,
the red light comes on just before the
(Red)
capacity of the current filter runs out. Changing
the filter on time provides you with the freshest,
cleanest water from your refrigerator.
1. Shut off the water supply. Then, turn the water
filter ( 1 ) about 1/4 turn, counter-clockwise.
2. Pull the water filter ( 1 ) from the case filter ( 2 ).
• To change the water filter more easily,
shut off the water supply valve.
• Sometimes, it is hard to disassemble the water
filter because impurities in the water cause it
to stick. If you are having difficulties, grip the
water filter firmly and pull it hard.
• When you pull the
water filter, a little
water can leak from
the opening. This is
2
3
normal. To minimize
the water leaks, keep
the filter cartridge horizontal when you pull it.
• To prevent overflow, empty the water filter tray
( 3 ) and dry around the filter case ( 2 ).
3. Insert the new filter into the filter case ( 4 ).
4. Push the filter, and then turn it clockwise until it
locks.
• If you have trouble inserting the water
filter because of high water pressure,
shut off the water supply valve.
• The locked symbol should be lined up
with the indicator line.
4
operating _13
2
1
02 OPERATING
DA68-02603A-03.indb 1313. 4. 25. �� 2:12
5. Touch the “Alarm/hold
3 sec for Filter Reset”
button (
(Filter Reset)
3 seconds to reset the
water filter. The color of the
indicator ( ) changes from red to off.
6. If you turned off the water supply, turn it back
on.
For a replacement water filter, you can
visit your local home Improvement center
or contact the Samsung Parts distributor.
Be sure the replacement water filter has
the SAMSUNG logo on the box and
on the water filter. Link : http://www.
samsungparts.com
) for about
Removing any residual matter inside
the water supply line after installing
the water filter.
1. Turn ON the main water
supply and supply water
from water supply line.
2. Run water through the
dispenser until the water
runs clear (approx. 6 to 7
minutes). This will clean
the water supply system and remove air from
the lines.
3. Additional flushing may be required in some
households.
4. Open the Refrigerator door and make sure
there are no water leaks coming from the
water filter.
• Check to see whether the sediment filter in the
reverse osmosis system is blocked. Replace
the filter if necessary.
• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
• If your refrigerator has a water filter, it may
further reduce the water pressure when used
in conjunction with a reverse osmosis system.
Remove the water filter.
If you have questions about your water pressure,
call a licensed, qualified plumber.
CONTROLLING THE
TEMPERATURE
Basic temperature of Freezer and
Refrigerator Compartments
The basic temperature and recommended
temperatures of the Freezer and Refrigerator
Compartments are 0°F and 37°F (or -18°C and
3°C) respectively. If the temperature of the Freezer
and Refrigerator Compartments are too high or
low, adjust the temperature manually.
Controlling the Freezer
temperature
Be sure to flush the dispenser thoroughly,
otherwise water may drip from the
dispenser.
This means that there is still air in the line.
Reverse Osmosis Water Supply
IMPORTANT:
The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet
valve of the refrigerator needs to be between 35
and 120 psi (241 and 827 kPa).
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi (276 to 414 kPa.) If
the water pressure to the reverse osmosis system
is less than 40 to 60 psi (276 to 414 kPa):
14_ operating
DA68-02603A-03.indb 1413. 4. 25. �� 2:12
Recommend Temp (Freezer) : 0°F (or -18°C )
The Freezer temperature can be set between -8°F
and 5°F (or between -23°C and -15°C) to suit
your particular needs. Press the Freezer button
repeatedly until the desired temperature is shown
in the temperature display. The temperature will
change by 1°F (or 1°C) with each press. See
below.
Fahrenheit : 0°F ➞ -1°F ➞ -2°F ➞ -3°F ➞ -4°F ➞
-5°F ➞ -6°F ➞ -7°F ➞ -8°F ➞ 5°F ➞ 4°F ➞ 3°F
2°F ➞ 1°F ➞ 0°F.
➞
Centigrade : -18°C ➞ -19°C ➞ -20°C ➞ -21°C
-22°C ➞ -23°C ➞ -15°C ➞ -16°C ➞ -17°C ➞
➞
-18°C.
Keep in mind that foods like some ice cream may
melt at 4°F (or -15.5°C). The temperature display
will move sequentially from -8°F to 5°F (or from
-23°C to -15°C).
Controlling the fridge temperature
The fridge temperature can be set between
34°F and 44°F (or between 1°C and 7°C) to suit
your particular needs. Press the Fridge button
repeatedly until the desired temperature is shown
in the temperature display. The temperature will
change by 1°F (or 1°C) with each press. See
below.
Fahrenheit : 37°F ➞ 36°F ➞ 35°F ➞ 34°F ➞ 44°F
43°F ➞ 42°F ➞ 41°F ➞ 40°F ➞ 39°F ➞ 38°F
➞
37°F.
➞
Centigrade : 3°C ➞ 2°C ➞ 1°C ➞ 7°C ➞ 6°C ➞
5°C ➞ 4°C ➞ 3°C.
The temperature control process for the Fridge
works just like the Freezer process. Press the
Fridge button to set your desired temperature.
After a few seconds, the Fridge will begin
adjusting towards the newly set temperature. This
will be reflected in the digital display.
Recommend Temp (Fridge) : 37°F (or 3°C )
- The temperature of the Freezer, Fridge
or Cool Select Pantry Zone may rise
when you open the doors too frequently,
or if a large amount of warm or hot food
- This may cause the digital display to blink.
- If the blinking continues, you may need to
- If there is a communication error between the
is placed inside.
Once the Freezer and Fridge temperature
return to their normal set temperatures, the
blinking will stop.
“reset” the Refrigerator. Try unplugging the
appliance, wait for around 10 minutes and then
plug the power cord back in.
Display and Main Controller, the Convertible
Display light may blink. If the blinking continues
for a long period of time, please contact a
Samsung Electronics Service Center.
USING THE COLD WATER DISPENSER
Push the appropriate ice type button
to select what you want dispensed.
02 OPERATING
Select this if you want to
Using the ice lever ( 1 )
Push the Ice lever dispenser ( 1 )
gently with your glass. Ice will be
released from the dispenser.
You can choose the type of ice
by pushing the cubed or crushed
button first.
Using the Water lever ( 2 )
Push the Water lever dispenser ( 2 ) gently with your
glass. Water will be released from the dispenser.
Even if you push the water and Ice lever
simultaneously, the dispenser operates only
the option you selected or pushed first.
Please wait 1 second before removing the cup
after dispensing water to prevent spills. Do not
pull out the lever dispenser after dispensing
ice or water. It comes back automatically.
Using the Ice & Water Dispenser together
To get Ice and water, push the Ice lever ( 1 ) first
for ice, then move your glass down and press the
water dispenser lever (2) for water.
Maintaining the Ice Bucket
• To clean the ice bin/bucket, wash with a mild
detergent, rinse well, and dry thoroughly it. Do
not use harsh or abrasive cleaners or solvents.
• Ice is made in cubes. When you select “Crushed”,
the ice maker grinds the ice cubes into crushed ice.
• When you select Cubed Ice after using the
Crushed Ice mode, a small amount of residual
crushed ice might be produced.
• The ice cubes generated by the rapid ice
making process will look white, which indicates
they are generated normally.
• As the ice maker in the refrigerator room
makes ice cubes even faster, move the ice
cubes from the refrigerator ice bin to the
NO ICE
turn ice maker off
1
2
operating _15
DA68-02603A-03.indb 1513. 4. 25. �� 2:12
freezer ice bin if you need more ice cubes.
• If ice doesn’t come out, pull out the ice bucket
and press the test button located on the right
side of ice maker. See the illustration below.
• Do not press the test button continuously
when the tray is filled with ice or water. Water
may overflow or ice may jam the bucket.
Making Ice
• To fill the ice bucket to maximum capacity after
installation, follow these steps:
1. Allow your refrigerator to operate and cool
down for 24 hours (or 1 full day).
- Waiting 24 hours will allow your ice maker to
cool properly.
2. Dispense 4 to 6 ice cubes into the glass.
3. After 8, and then 16 hours, dispense a full
glass of ice.
• When you press the Test button on the
icemaker, you will hear the refrigerator chime
(ding-dong). When the chime sounds, release
the Test button.
• The chime sounds automatically again to let
you know the ice maker is working well.
check the
water level
Test button
If you use all the ice at once, you must
repeat Steps 2 and 3 above.
However, only wait 8 hours before dispensing the
first 4 to 6 ice cubes. This will replenish the ice
cubes and ensure maximum ice production.
Using the ice off Function
When you select the Ice Off mode, remove all ice
cubes from the bucket. If you are not using the ice
dispenser, the ice cubes may clump together.
Keep pushing button. Remove bucket as arrow
direction. Throw away the ice cubes or clumped
ice. Push the bottom of the bucket until you hear
a click. When the bucket does not fit, turn the
helix by 90 degree and try again.
• Use only the ice maker provided with
CAUTION
the refrigerator.
• The water supply to this refrigerator
must only be installed/connected by a
suitably qualified person.
• Connect to a potable water supply only.
• To operate the ice maker properly, water
pressure of 20 ~ 125 psi is required.
Going on vacation...
If you want to remove the ice cubes without
CAUTION
using the ice bucket, please turn the ice
maker off. (However, remove the front cover
from the ice maker.) The ice cubes in the
ice maker can spill out over the drawer.
Do not put food in the ice bucket. If you store
CAUTION
food in the ice bucket, the food may get in the
way of the ice maker while opening/closing
the door, causing damage to the ice maker.
Note that the ice cubes in the ice bucket
may spill out over the drawer when
CAUTION
removing the ice bucket from the drawer.
If this is the case, be sure to clear the ice
cubes that spilled out of the drawer.
If a power failure occurs, ice cubes may
melt then freeze together when the power
CAUTION
comes back on, causing the dispenser to
be out of order.
To prevent this problem, after a power failure, pull out
the ice bucket and discard the residual ice or water.
16_ operating
DA68-02603A-03.indb 1613. 4. 25. �� 2:12
If you have a long vacation or business trip and won’t
use the water or ice dispensers for a long time:
- Close the water valve. Otherwise, water
leakage may occur.
- Remove all food.
- Unplug the refrigerator.
- Wipe excess moisture from inside and leave
the doors open. Otherwise, odor and mold
may develop.
Ice Maker Do’s and Don’ts
Do not put your fingers, hands or any other
unsuitable objects in the chute or ice-maker bucket.
- It may result in personal injury or material
damage. Never put your finger or any other
objects in the dispenser opening.
- It may cause injury.
Do not try to disassemble the ice maker.
Do not wash or spray the ice bucket with water
while it is in the refrigerator. Remove it to clean it.
When you insert the Ice maker tray, be sure
that the tray is well centered at the entrance.
CAUTION
Otherwise, the tray may be stuck.
Water clouding phenomenon
All water provided to the refrigerator flows
through the core filter which is an alkaline
may temporarily look misty or cloudy due
to these oxygen bubbles. After a few
seconds, the water will look clear.
water filter. In the filtering process, the
pressure of the water that has flowed out
of the filter is increased, and the water
becomes saturated with oxygen and
nitrogen. When this water flows out into
the air, the pressure plummets and the
oxygen and nitrogen get supersaturated,
which results in gas bubbles. The water
PARTS AND FEATURES
Use this page to become more familiar with the parts and features of the refrigerator.
Light
FF Ice-Maker
Foldable-Shelf
Slide-Shelf
02 OPERATING
Door Closer
Slide-Shelf
Vertical Hinged
Section
Vegetable &
Fruit Drawers
Light
FZ Ice-Maker
Ice Bucket
Guard
Quick-Space
Glass Shelf
(on some models)
Door Bins
Cool Select
Pantry
Auto Pull Out
Drawer
Freezer
Drawer Bin
When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid
scratching the other door.
If the Vertical Hinged Section is reversed, put it back to the right position and close the door.
Moisture may appear at times on the Vertical Hinged Section.
The door handle may become loose over time. If this happens, tighten the bolts found on the
inside of the door.
If you close one door with a lot of force, the other door may open.
When the door opens, the interlock switch automatically turns off the auger motor in the ice
maker for safety reasons.
When the interior or exterior LED lamp has gone out, please contact your service agents.
operating _17
PLUS
DA68-02603A-03.indb 1713. 4. 25. �� 2:12
USING THE COOL SELECT
PANTRY™
The Cool Select Pantry™ is a full-width drawer
with adjustable temperature control. This pantry
can be used for large party trays, deli items, pizza,
beverages, or miscellaneous items.
There is a temperature control which can adjust
the amount of cold air allowed into the pantry.
The control is located on the right side of the
pantry.
• The Pantry has three modes: The Fresh mode,
Chilled mode, and Deli mode. Fresh mode is
the default. Press the Temp button repeatedly
until the mode you want is lit. Once you select
a mode, the temperature will change to match
the mode you selected.
• The Pantry temperature may change
depending on the number of items inside
and where they are located, the ambient
temperature, and how often the door is
opened.
The Pantry Selection Button
1. When you select “Deli”, the temperature of the
pantry will be kept around 41°F (or 5°C). This
feature helps keep food fresh for a long time.
2. When you select
“Fresh”, the
temperature of the
pantry will be kept
around 38°F (or 3°C).
This feature helps keep
food fresh for a longer
time.
3. When you select
“Chilled”, the
temperature of the
pantry will be kept around 34°F (or 1°C). This
feature also helps keep meat or fish fresh for a
longer time.
The table below lists the Pantry modes and
the kinds of foods that can be stored safely for
each mode.
DeliFreshChilled
• Pineapple• cucumbers• steaks
• lemon• apples• hard cheeses
• avocado• oranges• cold cuts
• potato• grapes• bacon
Fruits and vegetables may be damaged
when the “Chilled” mode is set.
Do not store lettuce or other leafy produce in this
pantry.
Do not store glass bottles in this pantry. If
CAUTION
they are frozen, they can break and cause
personal injury.
• zucchinis• hot dogs
• corn
REMOVING THE REFRIGERATOR
ACCESSORIES
1. Door Bins
• Door Bins (1)
To remove - Simply lift the bin up and pull straight
out. To relocate - Slide it in above the desires
location and push down until it stops.
• Door Bins (2)To remove - Take the right side of the bin out by
lifting it at an angle along the guide, and then take
the left side out by pulling it from the door.
To relocate - Slide it into the original location and
push down until it sticks.
1
2
Injury may occur if the door bins are not
firmly assembled.
Do not allow children to play with the bins. Sharp
corners of the bins may cause injury.
18_ operating
DA68-02603A-03.indb 1813. 4. 25. �� 2:12
Do not adjust a bin full of food. Remove
CAUTION
the food first.
To remove dust from the bins : Remove the guard
and wash in water.
2. Tempered Glass shelves
To remove - Tilt up the front of the shelf in the
direction shown ( 1 ) and lift it up vertically ( 2 ).
Pull the shelf out.
To relocate - Tilt the front of the shelf up and
guide the shelf hooks into the slots at a desired
height. Then lower the front of the shelf so that the
hooks can drop into the slots.
The Tempered Glass shelves are heavy.
CAUTION
Use special care when removing them.
1
2
3. Vegetable & Fruit Drawers
To remove - Pull the drawer out to full extension.
Tilt up the front of the drawer and pull straight out.
To relocate - Insert the drawer into the frame rails
and push back into place.
The drawers need to be removed before
CAUTION
the glass shelf above them can be lifted
out.
To remove the divider – Pull the pantry
completely out to full extension and raise the front
side of the divider to unhook it from the rear wall
of the pantry, then lift the divider out.
To relocate the divider - Hook the back of the
divider over the rear wall of the pantry and push
the divider down.
02 OPERATING
Using the doors
Ensure that the doors close all the way and are
securely sealed.
When the refrigerator door is only partially open,
it will automatically close. But, the door will stay
open when opened more than the auto close
range and you must close it manually.
REMOVING THE REFRIGERATOR
ACCESSORIES
1. Freeze room Guard
To remove - Remove the freeze room guard ( 1 )
by lifting the guard up.
To relocate - Push down until the guard ( 1 )
locks into place.
1
2. ICE BUCKET (in Super Extender
4. Flex Zone
To remove the Flex
Zone – Pull the pantry
out to full extension.
Tilt up the front side
of the pantry and pull
straight out.
To relocate the Flex Zone – Push the rails to the
back of the refrigerator. Place the drawer onto the
rails and slide the pantry back until it is in place.
DA68-02603A-03.indb 1913. 4. 25. �� 2:12
drawer)
To remove - Lift the ice bucket ( 1 ).
To relocate - Place the ice bucket into the Super
extended drawer ( 2 ).
2
1
operating _19
3. Super Extended Drawer
To remove - Pull the drawer out to full extension.
Tilt up the rear of the drawer and lift straight out.
To relocate - Place the drawer onto the rails ( 4 )
by tilting it up. Lower the drawer into place until it
is horizontal and slide the Drawer ( 3 ) in.
4
3
Cleaning the Interior
Clean the inside walls and accessories with a mild
detergent and then wipe dry with a soft cloth. You
can remove the drawers and shelves for a more
thorough cleaning. Just make sure to dry drawers
and shelves before putting them back into place.
4. Freezer Drawer
To remove the freezer drawer - Pull the freezer
drawer out fully. Tilt up the rear of the bin and lift it
out to remove.
To relocate the freezer drawer - Place the bin
into the rail assembly.
Do not allow babies or children go inside
CAUTION
the freezer drawer. They could damage the
refrigerator and seriously injure themselves.
Do not sit on the freezer door. The door
may break. Do not allow children to climb
into the freezer drawer.
Do not remove the divider.
CAUTION
If trapped inside, children may be injured
WARNING
or suffocate to death.
Cleaning the Exterior
Wipe the control panel and digital display with
a damp, clean, soft cloth. Do not spray water
directly on the surface of the refrigerator.
The doors, handles, and cabinet surfaces should
be cleaned with a mild detergent and then wiped
dry with a soft cloth. To keep your appliance
looking its best, polish the exterior once or twice a
year.
Do not spray water directly on the
CAUTION
refrigerator. Use a clean, damp cloth to
clean.
Do not use benzene, thinner, or Clorox for
cleaning. They may damage the surface of
CAUTION
the appliance and may cause a fire.
You can erase the printed
CAUTION
letters on the display if you
apply stainless cleaner directly
to the area where the letters
are printed.
Cleaning the Ice / Water Dispenser
Push down one end of the tray dispenser and
CLEANING THE
REFRIGERATOR
Caring for your Samsung French Door Refrigerator
prolongs the life of your appliance and helps keep
the refrigerator free of odor and germs.
20_ operating
DA68-02603A-03.indb 2013. 4. 25. �� 2:13
remove it. Wipe the Ice / Water Dispenser with a
clean and soft cloth.
When using the crushed ice selection from
CAUTION
the dispenser some residual ice chips may
start to collect in the ice chute. To prevent
that residual ice from melting and running
out of the chute, you should clean out the
residual ice when you see
it start to collect in the ice
chute.
Cleaning the Rubber door seals
If the rubber door seals are dirty, the doors may
not close properly, and the refrigerator will not
operate efficiently. Keep the door seals free of
dust or stains by cleaning the doors with a mild
detergent and damp cloth. Wipe dry with a clean,
soft cloth.
Do not clean the refrigerator with benzene,
CAUTION
thinner, or car detergent. These substances
could cause a fire.
Cleaning the rear side of the
refrigerator
To keep cords and exposed parts free of dust and
dirt accumulation.
Vacuum the rear side of the appliance once or
twice a year.
Do not remove the back cover ( 1 ).
CAUTION
You could suffer an electric shock.
1
02 OPERATING
operating _21
DA68-02603A-03.indb 2113. 4. 25. �� 2:13
FOOD STORAGE TIPS
FoodsRefrigeratorFreezerStorage Tips
DAIRY PRODUCTS
Butter2-3 Weeks6-9 MonthsWrap or cover tightly.
Check date code. Most milk and similar prod-
Milk1-2 WeeksNot recommended
Cream Cheese, cheese
food, and cheese spread
Hard Cheese (unopened) 3-4 Months6 Months
Hard Cheese (opened)2 MonthsNot recommended
Cottage Cheese10-15 DaysNot recommended
Cream7-10 Days2 MonthsCheck date code. Most yogurt, creams, and
Sour Cream2 WeeksNot recommended
Cream Dips (opened)1 WeekNot recommended
Yogurt10-14 DaysNot recommended
Frozen Yogurtna2 Months
EGGS
Eggs (uncooked)3-4 WeeksNot recommended
Eggs (cooked)1 WeekNot recommendedStore in covered container
Leftover egg dishes3-4 DaysNot recommendedStore in covered container
FRESH FRUITS
Apples1 MonthNot recommended
Bananas2-4 DaysNot recommended
Peaches, Melons, Pears,
Avocados
Berries and Cherries2-3 Days12 Months
Apricots3-5 DaysNot recommended
Grapes2-5 Daysna
Pineapple (un-cut)2-3 DaysNot recommended
Pineapple (cut)5-7 Days6-12 Months
Citrus1-2 WeeksNot recommendedStore uncovered.
Juice6 DaysNot recommended
Frozen JuiceThawing only12 MonthsCheck date code. Do not re-freeze.
2-4 WeeksNot recommended
3-5 DaysNot recommended
ucts are sold in date-coded cartons that indicate
a products’s peak freshness. Re-seal with cap
or wrap tightly. Do not return unused portions to
original container.
Check date code. Keep all cheese tightly packed
in moisture proof wrap
similar products are sold in date-coded cartons
that indicate a product’s peak freshness. Re-seal
or cover tightly. Do not return unused portions to
original container.
Check date code. Keep covered.
Check date code. Store eggs in coldest part of
refrigerator and in their original container.
If storing in refrigerator, do not wash fruit before
storing. Store in moisture resistant bags or
containers. Wrap cut fruits. Some fruits darken
when refrigerated.
Check date code and re-seal in original container. Do not return unused portions to original
container.
22_ operating
DA68-02603A-03.indb 2213. 4. 25. �� 2:13
FoodsRefrigeratorFreezerStorage Tips
FISH AND SHELLFISH
Fish
Fatty Fish (mackerel, trout, salmon)
Lean Fish (cod,
flounder, etc)
Frozen or Breadedna3 Months
Shellfish
Shrimp (uncooked)1-2 Days12 Months
Crab3-5 Days10 Months
Cooked Fish or
Shellfish
MEAT
Fresh, Uncooked
Chops2-4 Days6-12 Months
Ground1 Day3-4 Months
Roast2-4 Days6-12 Months
Bacon1-2 Weeks1-2 Months
Sausage1-2 Days1-2 Months
Steak2-4 Days6-9 Months
Poultry1 Day12 Months
Lunch meat3-5 Days1 Month
Cooked
Meat2-3 Days2-3 Months
Poultry2-3 Days4-5 Months
Ham1-2 weeks1-2 Months
1-2 Days2-3 Months
1-2 Days6 Months
2-3 Days3 Months
Keep in original wrapper and store in coldest part of
refrigerator. Package in vapor-proof and moisture
proof wrap for freezer. Freeze at 0ºF(or -18°C ). Thaw
in refrigerator or check date code. Freeze in original
packaging.
To freeze, package in vapor-proof and moisture-proof
container.
Check date code for use. Store in coldest part of
refrigerator in original packaging. Package in moistureproof and vapor-proof container for freezing. Recommended refrigerator temperature 33ºF to 36ºF (or 1°C
to 2°C ) and freezer temperature 0ºF to 2ºF (or -18°C
to -16°C )
Check date code for use. Store in coldest part of
refrigerator in original packaging. Package in moistureproof and vapor-proof container for freezing.
02 OPERATING
Sources:
American Meat Institute Foundation. 1994. Yellow pages: answers to predictable questions consumers ask about
meat and poultry. American Meat Institute Food Marketing Institute. 1999. The food keeper. Food Marketing Institute,
Washington, D.C. Freeland-Graves, J.H. and G.C. Peckham. 1996. Foundations of food preparation, 6th ed. PrenticeHall, Inc. Englewood Cliffs, NJ. Hillers, V.N. 1993. Storing foods at home. Washington State University Cooperative
Extension, Pullman, WA. Publ. EB 1205.
National Restaurant Association. 2001. Be cool-chill out! Refrigerate promptly. National Restaurant Association
Education Foundation¼s International Food Safety Council, Washington, D.C. USDA. 1997. Basics for handling food
safely. U.S. Department of Agriculture, Food Safety and Inspection Service, Washington, D.C.
operating _23
DA68-02603A-03.indb 2313. 4. 25. �� 2:13
Troubleshooting
PROBLEMSOLUTION
The refrigerator
does not work at
all or it does not
chill sufficiently.
The food in the
fridge is frozen.
You hear unusual
noise or sounds.
The cabinet-door
sealing area of the
appliance is hot
and condensation
is occurring.
Ice Maker is not
producing ice.
You can hear
water bubbling in
the refrigerator.
There is a bad
smell in the
refrigerator.
Frost forms on
the walls of the
freezer.
Water dispenser
is not functioning.
Auto close
system does not
work with the
freezer door.
Condensation or
water drops forms
on both sides
of fridge door’s
central part.
24_ Troubleshooting
• Check that the power plug is properly connected.
• Check if the set temperature on the digital display is warmer than the freezer or fridge
inner temperature. If it is, set the refrigerator colder.
• Is the refrigerator in direct sunlight or located near a heat source?
• Is the back of the refrigerator too close to the wall, preventing proper ventilation?
• Check if the set temperature on the digital display is too low.
• Try setting the refrigerator to a warmer temperature.
• Is the temperature in the room too low? Set the refrigerator warmer.
• Did you store the food which is juicy in the coldest part of the refrigerator? Try moving
those items to the other shelves in the fridge instead of keeping them in the colder
areas or bins.
• Check that the refrigerator is level and stable.
• Is the back of the refrigerator too close to the wall, preventing proper ventilation?Try moving the back of the refrigerator at least 2 inches from the wall.
• Was anything dropped behind or under the refrigerator?
• A “ticking” sound is heard from inside the refrigerator. It is normal and occurs because
various accessories are contracting or expanding according to the temperature of the
refrigerator interior.
• If it sounds as if something is hitting something else inside the refrigerator, this is normal.
The sound is caused by the compressor operating at high capacity.
• Some heat is normal as anti-condensators are installed in the vertical hinged section of
the refrigerator to prevent condensation.
• Is the refrigerator door ajar? Condensation can occur when you leave the door open for
a long time.
• Did you wait for 12 hours after installation of the water supply line before making ice?
• Is the water line connected and the shut-off valve opened?
• Did you manually stop the ice making function?
• Is the freezer temperature too warm? Try setting the freezer temperature lower.
• This is normal. The bubbling comes from refrigerant circulating through the refrigerator.
• Check for spoiled food.
• Foods with strong odors (for example, fish) should be tightly covered.
• Clean out your freezer periodically and throw away any spoiled or suspicious food.
• Is the air vent blocked? Remove any obstructions so air can circulate freely.
• Allow sufficient space between the stored foods for efficient air circulation.
• Is the freezer drawer closed properly?
• Is the water line connected and the shut-off valve opened?
• Has the water supply line tubing been crushed or kinked?
• Make sure the tubing is free and clear of any obstruction.
• Is the water tank frozen because the fridge temperature is too low?
Try selecting a warmer setting on the Digital display.
• Is there an imbalance between the right and left parts of the door?
• Open and close the door smoothly 1~2 times. After you do this, the auto close system
usually works properly again.
• Try opening the door smoothly to avoid unbalancing the right part and the left part of
the door.
• Condensation or water drops may form if the humidity is too high while the refrigerator
is operating.
• If condensation or water drops appears on both sides of fridge door’s central part, turn
the Energy Saver mode off after removing the condensation.
DA68-02603A-03.indb 2413. 4. 25. �� 2:13
Warranty(USA)
WARRANTY ON SAMSUNG REFRIGERATOR
LIMITED WARRANTY TO ORIGINAL PURCHASER
This Samsung brand product, as supplied and distributed by Samsung Electronics America, Inc. (Samsung)
and delivered new, in the original carton to the original consumer purchaser, is warranted by Samsung against
manufacturing defects in materials and workmanship for a limited warranty period of:
One (1) year Parts and Labor on Refrigerator
Five (5) years Parts and Labor on sealed Refrigeration system only*
(*Compressor, evaporator, condenser, drier, connecting tubing)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and
used in the United States. To receive warranty service, the purchaser must contact Samsung for problem
determination and service procedures. Warranty service can only be performed by a Samsung authorized
service center. The original dated bill of sale must be presented upon request as proof of purchase to Samsung
or Samsung authorized service center.
Samsung will repair or replace any part found to be defective, at our option and at no charge as stipulated
herein, with new or reconditioned parts during the limited warranty period specified above. All replaced parts
and products become the property of Samsung and must be returned to Samsung. Replacement parts and
products assume the remaining original warranty, or ninety (90) days, whichever is longer.
In-home service will be provided during the warranty labor period subject to availability within the contiguous
United States. In-home service is not available in all areas. To receive in-home service, the product must be
unobstructed and accessible from floor level to service personnel. If during in-home service repair cannot be
completed, it may be necessary to remove, repair and return the product. If in-home service is unavailable,
Samsung may elect, at our option, to provide for transportation of our choice to and from a Samsung authorized
service center. Otherwise, transportation to and from the Samsung authorized service center is the responsibility
of the purchaser.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,
noncommercial use of this product, and shall not apply to the following, including, but not limited to: damage
which occurs in shipment; delivery and installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire,
water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies,
accessories, applications, installations, repairs, external plumbing and leaks, external wiring, circuit breakers,
fuses or connectors not supplied and authorized by Samsung, or which damage this product or result in service
problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow
operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in
the instruction book; loss of food due to spoilage; consumable items including filters and light.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND
NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY
AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY
OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT
SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR
PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT,
REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND
AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY
SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER
ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER’S
PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO
USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG.
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER
OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state.
To obtain warranty service, please contact Samsung at:
SAMSUNG CUSTOMER CARE CENTER
Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660
1-800-SAMSUNG (1-800-726-7864) and www.samsung.com
DA68-02603A-03.indb 2513. 4. 25. �� 2:13
In case the need for servicing arises
Do not hesitate to call any Samsung Authorized Service Center nearby giving them your name, address
and telephone number when your product is not functioning properly.
Warranty Information
Limited Warranty for Original Purchaser
This Samsung product is warranted by Samsung Electronics Canada, Inc. (hereafter referred to as SECA)
against manufacturing defects in material or workmanship for the following periods:
Labor : 1 year (in-home)
Parts : 1 year
Inverter Compressor : 10 years
SECA further warrants that if this product fails to operate properly within the specified warranty period and
the failure is due to improper workmanship or defective material, SECA will repair or replace the product at
its option.
All warranty repairs or part replacements must be performed by a SECA Authorized Service Center. (To find
the nearest SECA Service Center, call 1-800-SAMSUNG (7267864) or visit our web site at www.samsung.
com/ca)
Obligation to the Original Owner
The original dated sales receipt must be retained by the customer and is the only acceptable proof of purchase.
It must be presented to a SECA Authorized Service Center at the time service is requested before warranty
services are rendered. On all carry-in models, transportation to and from the Authorized Service Center is the
responsibility of the customer.
Exclusions of the Warranty
This warranty does not cover damage due to accident, fire, flood, and/or other Acts of God, misuse, incorrect
line voltage, improper installation, improper or unauthorized repairs, commercial use, or damage that occurs
during shipping. Customer adjustments which are explained in this owners manual are not covered under the
terms of this warranty. This warranty will automatically be voided for any unit found with a missing or altered
serial number. This warranty is valid only on products purchased and used in the Canada.
Samsung Electronics Canada Inc., Customer Service
55 Standish Court Mississauga, Ontario L5R 4B2
(
CANADA
Canada
)
Customer Care Center 1-800-SAMSUNG(7267864)
Customer Care Center fax. 1-866-436-4617
If you have any questions or comments relating to Samsung products,